======================================================================
Changes since U-Boot 1.1.4:
======================================================================
+* Fix dbau1x00 Board
+ - Fix dbau1x00 boards broken by dbau1550 patch
+ PLL:s were not set for boards other than 1550.
+ Flash CFI caused card to hang due to undefined CFG_FLASH_BANKS_LIST.
+ Default boot is now bootp for cards other than 1550.
+ Patch by Thomas Lange Aug 10 2005
+
+* Fixes common/cmd_flash.c:
+
+ - fix some compiler/parser error, if using m68k tool chain
+ - optical fix for protect on/off all messages, if using more
+ then one bank
+ Patch by Jens Scharsig, 28 July 2005
+
+* Fix Lite5200B support: initialize SDelay register
+ See Freescale's AN3221 "MPC5200B SDRAM Initialization and
+ Configuration", 3.3.1 SDelay--MBAR + 0x0190
+
+* Changes/fixes for drivers/cfi_flash.c:
+
+ - Add Intel legacy lock/unlock support to common CFI driver
+
+ On some Intel flash's (e.g. Intel J3) legacy unlocking is
+ supported, meaning that unlocking of one sector will unlock
+ all sectors of this bank. Using this feature, unlocking
+ of all sectors upon startup (via env var "unlock=yes") will
+ get much faster.
+
+ - Fixed problem with multiple reads of envronment variable
+ "unlock" as pointed out by Reinhard Arlt & Anders Larsen.
+
+ - Removed unwanted linefeeds from "protect" command when
+ CFG_FLASH_PROTECTION is enabled.
+
+ - Changed p3p400 board to use CFG_FLASH_PROTECTION
+
+ Patch by Stefan Roese, 01 Apr 2006
+
+* Changes/fixes for drivers/cfi_flash.c:
+ - Correctly handle the cases where CFG_HZ != 1000 (several
+ XScale-based boards)
+ - Fix the timeout calculation of buffered writes (off by a
+ factor of 1000)
+ Patch by Anders Larsen, 31 Mar 2006
+
+* Updates to common PPC4xx onboard (DDR)SDRAM init code (405 and 440)
+
+ 405 SDRAM: - The SDRAM parameters can now be defined in the board
+ config file and the 405 SDRAM controller values will
+ be calculated upon bootup (see PPChameleonEVB).
+ When those settings are not defined in the board
+ config file, the register setup will be as it is now,
+ so this implementation should not break any current
+ design using this code.
+
+ Thanks to Andrea Marson from DAVE for this patch.
+
+ 440 DDR: - Added function sdram_tr1_set to auto calculate the
+ TR1 value for the DDR.
+ - Added ECC support (see p3p440).
+
+ Patch by Stefan Roese, 17 Mar 2006
+
+* Fix CONFIG_SKIP_LOWLEVEL_INIT dependency in cpu/arm920t/start.S
+ Patch by Peter Menzebach, 13 Oct 2005 [DNX#2006040142000473]
+
+* Add support for ymodem protocol download
+ Patch by Stefano Babic, 29 Mar 2006
+
+* Memory Map Update for Delta board: U-Boot is at 0x80000000-0x84000000
+ Merge from Markus Klotzbücher's repo, 01 Apr 2006
+
+* GCC-4.x fixes: clean up global data pointer initialization for all
+ boards
+
+* Update for Delta board:
+ - redundant NAND environment
+ - misc Monahans cleanups (remove dead code etc.)
+ - DA9030 Initialization; some minimal changes to PXA I2C driver to
+ make it work with the Monahans.
+ - Make Monahans clock frequency configurable using
+ CFG_MONAHANS_RUN_MODE_OSC_RATIO and
+ CFG_MONAHANS_TURBO_RUN_MODE_RATIO.
+ Merge from Markus Klotzbücher's repo, 25 Mar 2006
+
+* Enable Quad UART om MCC200 board.
+
+* Cleanup MCC200 board configuration; omit non-existent stuff.
+
+* Add support for MPC859/866 Rev. A.0
+
+* Add command for handling DDR ECC registers on MPC8349EE MDS board.
+
+* Fix DDR ECC bit definitions for MPC83xx.
+
+* Add initial support for MPC8349E MDS board.
+
+* Add support for ECC DDR initialization on MPC83xx.
+
+* Add DMA support for MPC83xx.
+
+* Add sync in do_reset() routine for MPC83xx after RPR register
+ was written to. It is need on some targets when BAT translation
+ is enabled.
+
+* Add bit definitions for MPC83xx DDR controller registers.
+
+* Add Dcbz(), Dcbi() and Dcbf() routines for MPC83xx.
+
+* Correct shift offsets in icache_status and dcache_status for MPC83xx.
+
+* Add support for DS1374 RTC chip.
+
+* Add support for Lite5200B board.
+ Patch by Patch by Jose Maria (Txema) Lopez, 16 Jan 2006
+
+* Apply SoC concept to arm926ejs CPUs, i.e. move the SoC specific
+ timer and cpu_reset code from cpu/$(CPU) into the new
+ cpu/$(CPU)/$(SOC) directories
+ Patch by Andreas Engel, 13 Mar 2006
+
+* Change max size of uncompressed uImage's to 8MByte and add
+ CFG_BOOTM_LEN to adjust this setting.
+
+ As mentioned by Robin Getz on 2005-05-24 the size of uncompressed
+ uImages was restricted to 4MBytes. This default size is now
+ increased to 8Mbytes and can be overrided by setting CFG_BOOTM_LEN
+ in the board config file.
+
+ Patch by Stefan Roese, 13 Mar 2006
+
+* Fix problem with updated PCI code in cpu/ppc4xx/405gp_pci.c
+ Patch by Stefan Roese, 13 Mar 2006
+
+* cpu/ppc4xx/start.S : exceptions are enabled after relocation
+ Patch by Cedric Vincent, 06 Jul 2005
+
+* au1x00_eth.c: check malloc return value and abort if it failed
+ Patch by Andrew Dyer, 26 Jul 2005
+
+* Change the sequence of events in soft_i2c.c:send_ack() to keep from
+ incorrectly generating start/stop conditions on the bus.
+ Patch by Andrew Dyer, 26 Jul 2005
+
+* Fix bug in [id]cache_status commands for MPC85xx processors;
+ should look at LSB of L1CSRn registers to determine if L1 cache is
+ enabled, not the MSB.
+ Patch by Murray Jensen, 19 Jul 2005
+
+* Fix array overflow with fw_setenv on uninitialised environment
+ Patch by Murray Jensen, 15 Jul 2005
+
+* Add support for EmbeddedPlanet EP88x boards
+ Patch by Yuli Barcohen, 13 Jul 2005
+
+* Remove board specific configuration includes from the common xilinx
+ ethernet and iic adapter code.
+ Patch by Michael Libeskind, 12 Jul 2005
+
+* Add Nat Semi DP83865 PHY support to MPC85xx TSEC driver
+ Patch by Murray Jensen, 08 Jul 2005
+
+* Add (some) definitions for the MPC85xx local bus controller
+ Patch by Murray Jensen, 08 Jul 2005
+
+* Add CPM2 I/O pin functions for MPC85xx processors
+ Patch by Murray Jensen, 08 Jul 2005
+
+* Fix compile problem
+
+* Added PCI support for MPC8349ADS board
+ Patch by Kumar Gala 11 Jan 2006
+
+* Enable address translation on MPC83xx
+ Patch by Kumar Gala, 10 Feb 2006
+
+* Decopuled setting of OR/BR and LBLAWBAR/LBLAWAR on MPC83xx
+ Patch by Kumar Gala, 25 Jan 2006
+
+* Fixed defines for MPC83xx SICRL register to match current specs
+ Patch by Kumar Gala, 23 Jan 2006
+
+* Only disable the MPC83xx watchdog if its enabled out of reset.
+ If its disabled out of reset SW can later enable it if so desired
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Allow config of GPIO direction & data registers at boot on 83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Enable time handling on 83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Make System IO Config Registers board configurable on MPC83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Fixed PCI indirect config ops to handle multiple PCI controllers
+ We need to adjust the bus number we are trying to access based
+ on which PCI controller its on
+ Patch by Kumar Gala, 12 Jan 2006
+
+* Report back PCI bus when doing table based device config
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Added support for PCI prefetchable region and BARs
+ If a host controller sets up a region as prefetchable and
+ a device's BAR denotes it as prefetchable, allocate the
+ BAR into the prefetch region.
+
+ If a BAR is prefetchable and no prefetchable region has
+ been setup by the controller we fall back to allocating
+ the BAR into the normally memory region.
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Add helper function for generic flat device tree fixups for mpc83xx
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Add support for passing initrd information via flat device tree
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Added OF_STDOUT_PATH and OF_SOC
+
+ OF_STDOUT_PATH specifies the path to the device the kernel can use
+ for console output
+
+ OF_SOC specifies the proper name of the SOC node if one exists.
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Allow board code to fixup the flat device tree before booting a kernel
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Added CONFIG_ options for bd_t and env in flat dev tree
+
+ CONFIG_OF_HAS_BD_T will put a copy of the bd_t
+ into the resulting flat device tree.
+
+ CONFIG_OF_HAS_UBOOT_ENV will copy the environment
+ variables from u-boot into the flat device tree
+
+ Patch by Kumar Gala, 11 Jan 2006
+
+* Add support for the DHCP vendor optional bootfile (#67).
+ Ignores the vendor TFTP server name option (#66).
+ Patch by Murray Jensen, 30 Jun 2005
+
+* Fix a HW timing issue on 8548 CDS for eTSEC 3 in RGMII mode
+ Patch by Andy Fleming, 14 Jun 2005
+
+* Fix bad register definitions for LTX971 PHY on MPC85xx boards.
+ Patch by Gerhard Jaeger, 21 Jun 2005
+
+* Add netconsole and some more commands to RPXlite_DW board
+ Patch by Sam Song, 19 Jun 2005
+
+* Fix bad declaration on pci_cfgfunc_nothing
+ Patch by Sam Song, 19 Jun 2005
+
+* Adjust "echo" as a default command
+ Patch by Sam Song, 19 Jun 2005
+
+* Fix PCIDF calculation in cpu/mpc8260/speed.c for MPC8280EC
+ Patch by KokHow Teh, 16 Jun 2005
+
+* Add crc of data to jffs2 (in jffs2_1pass_build_lists()).
+ Patch by Rick Bronson, 15 Jun 2005
+
+* Coding Style cleanup
+
+* Avoid dereferencing NULL in find_cmd() if no valid commands were found
+ Patch by Andrew Dyer, 13 Jun 2005
+
+* Add ADI Blackfin support
+ - add support for Analog Devices Blackfin BF533 CPU
+ - add support for the ADI BF533 Stamp uClinux board
+ - add support for the ADI BF533 EZKit board
+ Patches by Richard Klingler, 11 Jun 2005
+
+* Add loads of ntohl() in image header handling
+ Patch by Steven Scholz, 10 Jun 2005
+
+* Switch MPC86xADS and MPC885ADS boards to use cpuclk environment
+ variable to set clock
+ Patch by Yuli Barcohen, 05 Jun 2005
+
+* RPXlite configuration fixes
+ - Use correct flash sector size
+ - Use correct memory test end address
+ - Add support for bzip2 compression
+ - Various small fixes
+ Patch by Yuli Barcohen, 05 Jun 2005
+
+* Memory configuration changes for ZPC.1900 board
+ - Fix SDRAM timing on both local bus and 60x bus
+ - Add support for second flash bank (SIMM)
+ - Change boot flash base
+ Patch by Yuli Barcohen, 05 Jun 2005
+
+* Add support for Adder boards with 16MB SDRAM;
+ add support for second FEC on Adder87x board.
+ Patch by Yuli Barcohen, 05 Jun 2005
+
+* Fix conditional for including ks8695eth driver
+ Patch by Greg Ungerer, 04 Jun 2005
+
+* Fix Makefile: include config.mk only after CROSS_COMPILE is defined
+ Patch by Friedrich Lobenstock, 02 Jun 2005
+
+* Fix comment in common/soft_i2c.c
+ Patches by Peter Korsgaard/Tolunay Orkun, 26 May 2005
+
+* Cleanup compiler warnings.
+ Patch by Greg Ungerer, 21 May 2005
+
+* Word alignment fixes for word aligned NS16550 UART
+ Patch by Jean-Paul Saman, 01 Mar 2005
+
+ Fixes bug with UART that only supports word aligned access: removed
+ "__attribute__ ((packed));" for "(CFG_NS16550_REG_SIZE == 4)" some
+ (broken!) versions of GCC generate byte accesses when encountering
+ the packed attribute regardless if the struct is already correctly
+ aligned for a platform. Peripherals that can only handle word
+ aligned access won't work properly when accessed with byte access.
+ The struct NS16550 is already word aligned for REG_SIZE = 4, so
+ there is no need to packed the struct in that case.
+
+* Fix behaviour if gatewayip is not set
+ Patch by Robin Gilks, 23 Dec 2004
+
+* Fix cleanup for netstart board.
+ Remove build results from repository
+
+* Some code cleanup for GCC 4.x
+
+* Fixes to support environment in NAND flash;
+ enable NAND flash based environment for delta board.
+
+* Add support for Intel Monahans CPU on Zylonite and Delta boards
+ (This is Work in Progress!)
+
+* Add support for TQM8260-AI boards.
+
+* Minor code cleanup
+
+* Merge the new NAND code (testing-NAND brach); see doc/README.nand
+ Rewrite of NAND code based on what is in 2.6.12 Linux kernel
+ Patch by Ladislav Michl, 29 Jun 2005
+
+* Add lowboot target to mcc200 board
+ Patch by Stefan Roese, 4 Mar 2006
+
+* Fix problem with flash_get_size() from CFI driver update
+ Patch by Stefan Roese, 1 Mar 2006
+
+* Make CFG_NO_FLASH work on ARM systems
+ Patch by Markus Klotzbuecher, 27 Feb 2006
+
+* Update mcc200 config: Disable PCI and DoC, use 133 MHz IPB clock,
+ use hush shell.
* Convert mcc200 to use common CFI flash driver
Patch by Stefan Roese, 28 Feb 2006
which sets Intel 28F640J3 flash back to command mode on CSB472
Patch by Tolunay Orkun, 02 July 2005
+* Add basic support for the SMMACO4 Board from PanDaCom.
+ Patch by Heiko Schocher, 20 Feb 2006
+
* Add GIT version information (commid ID) to untagged U-Boot versions
As done in the linux kernel, the U-Boot version (U_BOOT_VERSION)