Changes since U-Boot 1.1.4:
======================================================================
+* Add support for high-boot on TQM5200 and TQM5200S boards.
+ Hint: the CPLD on the TQM5200 must be programmed with a software
+ version supporting the high boot option! The new TQM5200S is
+ already supporting this option. On the TQM5200 this option will be
+ supported in configurations with MPC5200 rev B processors.
+ To actually "high boot", set jumper X30 on the STK52xx.
+ Patch by Martin Krause, 12 Jul 2006
+
+* Add support for new TQM5200 revisions
+ - Support for TQM5200S (short version without graphic controller)
+ - Support for modules with 'N' type S29GL128N Spansion flashes
+ (requires changes to flash layout)
+ - Support for MPC5200B cpu (mostly support for second SDRAM bank)
+ Patch by Martin Krause, 07 Jul 2006
+
+* Fix support for PS/2 keyboard on TQM85xx boards
+ The PS/2 keyobard driver for the TQM85xx modules only supports the
+ internal DUART of the MPC85xx CPU. Since the MPC8560 doesn't
+ include a DUART, the TQM8560 modules can't be used with the PS/2
+ keyboard controller on the STK85xx board.
+ The PS/2 keyboard driver should work with the modules TQM8540,
+ TQM8541 and TQM8555, but it only has been tested on a TQM8540, yet.
+ Make sure the PS/2 controller on the STK85xx is programmed. Jumper
+ settings: X66 1-2, 9-10; X61 2-3
+ Patch by Martin Krause, 21 Jun 2006
+
+* Adjust RTC century handling on STK52xx board to match Linux driver.
+ Patch by Martin Krause, 12 Jun 2006
+
+* Adjust filenames for USB update images on TRAB board.
+ During an automatic update via USB stick, U-Boot searches for
+ images with the name "firmware.img" and "kernel.img". This names
+ are now changed to "firmw_01.img" and "kernl_01.img". This is done,
+ to prevent updates of new boards (with the new macronics "c" step
+ flashes) with old, incompatible firmware or kernel versions.
+ Patch by Martin Krause, 21 Jun 2006
+
+* Bugfix in VFD routine on TRAB board.
+ Make sure upper lext pixel can be set to blue, too
+ (so far only red was possible).
+ Patch by Martin Krause, 15 Feb 2006
+
+* Enable buffered flash writes for TB5200 board.
+
+* Fix some bugs in TRAB board flash driver.
+ - increase CFG_FLASH_ERASE_TOUT from 2 to 15 seconds
+ - use CFG_FLASH_WRITE_TOUT for programming instead of CFG_FLASH_ERASE_TOUT
+ - remove "Unlock Bypass" mode, because macronix flashes do not support
+ this mode officially
+ - fix flash reset command from 0x00FF to 0x00F0. 0x00FF is only specified
+ for Intel compatible flashes, not for AMD compatible.
+ Patch by Martin Krause, 15 Feb 2006
+
+* Add additional error messages to flash driver on TRAB board
+ (for erase errors and timeout errors)
+ Patch by Martin Krause, 14 Feb 2006
+
+* Add support for TB5200 board
+ The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module
+ integrated in a little aluminium case.
+ Patch by Martin Krause, 8 Jun 2006
+
+* Enable buffered flash writes for TQM5200 board.
+
+* Fix problems with SanDisk Corporation Cruzer Micro USB memory stick.
+
+* Add support for TQM885D board.
+ Patch by Martin Krause, 20 Mar 2006
+
+* Fix FEC initialisation: All MII configuration is done via FEC1
+ registers, but MII_SPEED was configured according to FEC used. So
+ if only FEC2 was used, this caused the real MII_SPEED register in
+ FEC1 to stay uninitalised, leqading to "mii_send STUCK!" messages.
+ Fix: always configure MII_SPEED on FEC1 only.
+ Patch by Markus Klotzbuecher, 12 Jul 2006
+
+* Add support for SPC1920 board.
+ Patch by Markus Klotzbuecher, 12 Jul 2006
+
+* MCC200 board: support console on any one of the Quad UART ports.
+
+* Fix error in flash protection calculation on MCC200 board.
+
+* Major PCMCIA Cleanup to make code better readable and maintainable.
+ Notes:
+ - Board-dependend code for RPXLITE and RPXCLASSIC-based boards
+ placed to the drivers/rpx_pmcia.c file to avoid duplication.
+ Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
+ - drivers/i82365.c has been split into two parts located at
+ board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
+ the only boards using CONFIG_82365).
+ - Changes were tested for clean build and *very* *few* boards.
+
+* Fix timer problems on AMCC yucca board.
+ Set Timer Clock Select to use CPU clock as a timer input source.
+
+* Bring yucca config more in line with other AMCC boards.
+
+* Add AMCC bamboo board to MAKEALL build script.
+
+* Fix AMCC bamboo eval board compilation errors.
+
+* Add system memory to the PCI region list for AMCC PPC44x CPUs.
+ Enabled it for Yucca board.
+
+* Cleanup config file and bootup output for Yucca board.
+
+* Fix CONFIG_440_GX define usage.
+
+* Remove autogenerated bmp_logo.h file.
+
+* Add support for AMCC 440SPe CPU based eval board (Yucca).
+
+* Call serial_initialize() before first debug() is used.
+
+* Cleanup trab board for GCC-4.x
+
+* VoiceBlue update: use new MTD flash partitioning methods, use more
+ reasonable TEXT_BASE, update default environment and enable keyed
+ autoboot.
+ Patch by Ladislav Michl, 16. Aug 2005
+
+* Add forgotten changes for the PLEB 2 Board.
+ Patch by David Snowdon, 13. Aug 2005
+
+* Add support for wrPPMC7xx/74xx boards
+ Patch by Richard Danter, 12 Aug 2005
+
+* Add support for gth2 board
+ Patch by Thomas Lange, Aug 11 2005
+
+* Add support for CONFIG_SERIAL_MULTI on MPC5xxx
+ Patch by Martin Krause, 8 Jun 2006
+
+ This patch supports two serial consoles on boards with
+ a MPC5xxx CPU. The console can be switched at runtime
+ by setting stdin, stdout and stderr to the desired serial
+ interface (serial0 or serial1). The PSCs to be used as
+ console port are definded by CONFIG_PSC_CONSOLE
+ and CONFIG_PSC_CONSOLE2.
+ See README.serial_multi for details.
+
+* Bugfix in I2C initialisation on S3C2400.
+ If the bus is blocked because of a previously interrupted
+ transfer, up to eleven clocks are generated on the I2CSCL
+ line to complete the transfer and to free the bus.
+ With this fix pin I2CSCL (PG6) is really configured as GPIO
+ so the clock pulses are really generated.
+ Patch by Martin Krause, 04 Apr 2006
+
+* Fix DDR6 errata on TQM834x boards
+ Patch by Thomas Waehner, 07 Mar 2006
+
+* Remove obsolete flash driver board/tqm5200/flash.c
+ Patch by Martin Krause, 11 Jan 2006
+
+* Update configuration for CMC-PU2 board
+ Patch by Martin Krause, 17 Nov 2005
+
+* Add support for PS/2 keyboard on TQM85xx board
+ Patch by Martin Krause, 07 Nov 2005
+
+ Tested on a STK85XX baseboard. Make sure the PS/2 controller
+ has been programmed. Jumper Settings: X66 1-2, 9-10; X61 2-3
+
+* Fix TRAB channel switching delay for trab_fkt.bin standalone applikation
+ In tsc2000_read_channel() the delay after setting the multiplexer
+ to a temperature channel is increased from 1,5 ms to 10 ms. This
+ is to allow the multiplexer inputs to stabilize after huge steps
+ of the input signal level.
+ Patch by Martin Krause, 08 Nov 2005
+
+* Adjust TQM5200 make targets
+ Make the automatic CS configuration the default.
+ The dedicated configurations CONFIG_TQM5200_AA, CONFIG_TQM5200_AB
+ and CONFIG_TQM5200_AC are removed.
+ "TQM5200_config" is now the default for STK52XX.200 base boards.
+ On a STK52XX.100 base board "TQM5200_STK100_config" must be used.
+ Patch by Martin Krause, 07 Nov 2005
+
+* Fix setting of environment variable "ver" on trab board
+ The environment variable "ver" is now set before
+ do_auto_update() is called, so that "ver" can be used
+ in USB update scripts.
+ Patch by Martin Krause, 27 Oct 2005
+
+* Fix wrong usage of udelay() in led_blink() on trab board
+ Patch by Martin Krause, 27 Oct 2005
+
+* Fix udelay bug in vfd.c for trab board
+ Patch by Martin Krause, 27 Oct 2005
+
+* Disable JFFS2 support for trab board
+ Patch by Martin Krause, 27 Oct 2005
+
+* Change mtdparts definition on trab board to match current flash map
+ Patch by Martin Krause, 27 Oct 2005
+
+* Fix memory init problems on MCC200 board
+
+* Fix IxEthDB.h to compile again
+ Patch by Stefan Roese, 14 Jun 2006
+
+* Minor cleanup for PCS440EP board
+ Patch by Stefan Roese, 13 Jun 2006
+
+* Add MCF5282 support (without preloader)
+ relocate ichache_State to ram
+ u-boot can run from internal flash
+ Add EB+MCF-EV123 board support.
+ Add m68k Boards to MAKEALL
+ Patch from Jens Scharsig, 08 Aug 2005
+
+* Nios II - Add Altera EP1C20, EP1S10 and EP1S40 boards
+ Patch by Scott McNutt, 08 Jun 2006
+
+* Nios II - Add EPCS Controller bootrom work-around
+ -When booting from an epcs controller, the epcs bootrom may leave the
+ slave select in an asserted state causing soft reset hang. This
+ patch ensures slave select is negated at reset.
+ Patch by Scott McNutt, 08 Jun 2006
+
+* Update PK1C20 board
+ -Update base addresses for standard configuration
+ -Eliminate use of CACHE_BYPASS in board code
+ Patch by Scott McNutt, 08 Jun 2006
+
+* Nios II - Fix I/O Macros and mini-app stubs
+ -Fix asm/io.h macros
+ -Eliminate use of CACHE_BYPASS in cpu code
+ -Eliminate assembler warnings
+ -Fix mini-app stubs and force no small data
+ Patch by Scott McNutt, 08 Jun 2006
+
+* Fix U-Boot environment sector protection on MCC200 board
+
+* Minor cleanup for PCS440EP board
+
+* Update PCS440EP port to fit into one flash device (incl. environment)
+ Patch by Stefan Roese, 06 Jun 2006
+
+* Add support for PCS440EP board
+ Patch by Stefan Roese, 02 Jun 2006
+
+* Fix examples/Makefile; some build targets were lost
+
+* Fix watchdog handling in CFI flash driver
+ Just use udelay() when waiting for status changes which will
+ implicitely trigger the watchdog.
+
+* Fix PCI to memory window size problems on PM82x boards
+ We use the "automatic" mode that was used for the MPC8266ADS and
+ MPC8272 boards. Eventually this should be used on all boards?]
+ Patch by Wolfgang Grandegger, 17 Jan 2006
+
+* Correct GPIO setup (UART1/IRQ's) on yosemite & yellowstone
+ Patch by Stefan Roese, 29 May 2006
+
+* Update Intel IXP4xx support
+ - Add IXP4xx NPE ethernet MAC support
+ - Add support for Intel IXDPG425 board
+ - Add support for Prodrive PDNB3 board
+ - Add IRQ support
+ Patch by Stefan Roese, 23 May 2006
+
+* Fix problem in PVR detection for 440GR
+ Patch by Stefan Roese, 18 May 2006
+
+* Fix gcc 3.4.x AFLAGS setting for m68k platform.
+
+* Enable autoboot for M5271EVB board.
+
+* Changed default ramdisk addr in yosemite/yellowstone ports
+ Patch by Stefan Roese, 15 May 2006
+
+* Fix PCMCIA support on virtlab2
+
+* Add support for VirtLab2 board
+ (needed because of differences in the PCMCIA hardware).
+
+* Minor cleanup.
+
+* Update yosemite configuration to enable flash write buffer support
+ Patch by Stefan Roese, 10 May 2006
+
+* Fix compile warnings in common/xyzModem.c
+ Patch by Stefan Roese, 10 May 2006
+
+* Add support for AMCC 440EP Rev C and 440GR Rev B
+ Patch by John Otken, 08 May 2006
+
+* OMAP 5912/OSK: update EMIFS CS1 timings:
+ Problems have been seen in the linux kernel's smc91x network driver
+ due to improper bus timings. The latest 2.6 OMAP kernels currently
+ have a workaround, but this fix belongs in u-boot.
+ Patch by Kevin Hilman, 13 Oct 2005
+
+* Fix REG_MPU_LOAD_TIMER definition in multiple OMAP ports
+ Patch by Hiroki Kaminaga, 11 Mar 2006
+
+* Update omap5912osk board support
+ - Fix OMAP support that omap5912osk compiles in current source tree
+ - Update with code from "http://omap.spectrumdigital.com/osk5912"
+ to fix problems with DDR initialization
+ - Fix timer setup
+ - Use CFI flash driver and support complete 32MB of onboard flash
+ - Add "print_cpuinfo()" and "checkboard()" functions to display
+ CPU (with frequency) and Board infos
+ Patch by Stefan Roese, 10 May 2006
+
* Fix watchdog issues for ColdFire boards.
* Add M5271EVB board support.
projects / platform / kernel / u-boot.git / blobdiff