+
+# Automatically enable Anycast 6to4 if possible. This is not recommended, as
+# the use of 6to4 will generally lead to a severe degradation of connection
+# quality. See RFC6343. Default value is false (as recommended by RFC6343
+# section 4.1).
+# Enable6to4 = false
+
+# Enable use of http get as on online status check.
+# When a service is in a READY state, and is selected as default,
+# ConnMan will issue an HTTP GET request to verify that end-to-end
+# connectivity is successful. Only then the service will be
+# transitioned to ONLINE state.
+# If this setting is false, the default service will remain in READY state.
+# Default value is true.
+# EnableOnlineCheck = false
+
+# List of technologies with AutoConnect = true which are always connected
+# regardless of PreferredTechnologies setting. Default value is empty and
+# will connect a technology only if it is at a higher preference than any
+# other which is already connected.
+# This setting has no effect if SingleConnectedTechnologies is enabled.
+# AlwaysConnectedTechnologies =
+
+# Allow connman to add service gateway to the time server list.
+# Default value is false.
+# UseGatewaysAsTimeservers = false
+
+# Enable auto connection of services in roaming.
+# If this setting is false, roaming services are not auto-connected by ConnMan.
+# Default value is false.
+# AutoConnectRoamingServices = false
+
+# Enable address conflict detection
+# If this setting is true, ConnMan will send probe ARP packets to see
+# if an IPv4 address is already in use before assigning the address
+# to an interface (in accordance with RFC 5227).
+# Default value is false.
+# AddressConflictDetection = false
+
+NetworkCellularInterfaceList = pdp,rmnet,seth_td,seth_w
+
+# Enable use of link-local address for auto-configuration.
+# When a device fails to get IP address from DHCP server,
+# ConnMan will start link-local address autoconfiguration and
+# assign a link-local IP address to device.
+# If this setting is false and device fails to get IP address
+# from DHCP server then device state will be set to disconnected.
+# Default value is true.
+# EnableAutoIp = false
+
+# Allow connman to set additional global nameserver and it will be used
+# if all nameservers are failed to resolve DNS query. The nameserver
+# entries must be in numeric format.
+# GlobalNameserver = 8.8.8.8
+
+# Enable supplicant debugging log
+ConnmanSupplicantDebug = false
+
+# Save ConnMan log to file
+FileLogging = false
+
+# Use dlog for ConnMan logging
+DlogLogging = true
+
+# Some logs of low importance are omitted to reduce the amount of logs
+SimplifiedLog = true
+
+# This value specifies which will be the default when there are multiple wifi interfaces.
+# Default value is wlan0.
+DefaultWifiInterface = wlan0
+
+[INS]
+# INS(Intelligent Network Selection) configuration: BSSID Selection.
+INSPreferredFreqBSSID = 5GHz
+INSPreferredFreqBSSIDScore = 20
+INSLastConnectedBSSID = true
+INSLastConnectedBSSIDScore = 20
+INSAssocReject = true
+INSAssocRejectScore = 10
+INSSignalBSSID = true
+
+# INS(Intelligent Network Selection) configuration: SSID Selection.
+INSLastUserSelection = true
+INSLastUserSelectionTime = 480
+INSLastUserSelectionScore = 30
+# (INSLastUserSelectionTime - selection time diff) / (INSLastUserSelectionTime / INSLastUserSelectionScore)
+# This means '(480 - selection time) / x) <= 30'
+INSLastConnected = true
+INSLastConnectedScore = 30
+INSPreferredFreq = 5GHz
+INSPreferredFreqScore = 60
+INSSecurityPriority = SAE,RSN
+INSSecurityPriorityScore = 5
+# In this case, SAE(10 score), RSN(5 score)
+INSSignal = true
+INSInternet = true
+INSInternetScore = 30
+
+# INS(Intelligent Network Selection) configuration: Common.
+INSSignalLevel3_5GHz = -76
+INSSignalLevel3_24GHz = -74