-/*
- * (C) Copyright 2000
- * Murray Jensen <Murray.Jensen@cmst.csiro.au>
- *
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2001
- * Advent Networks, Inc. <http://www.adventnetworks.com>
- * Jay Monkman <jtm@smoothsmoothie.com>
- *
- * Configuration settings for the SACSng 8260 board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#undef DEBUG_BOOTP_EXT /* Debug received vendor fields */
-
-#undef CONFIG_LOGBUFFER /* External logbuffer support */
-
-/*****************************************************************************
- *
- * These settings must match the way _your_ board is set up
- *
- *****************************************************************************/
-
-/* What is the oscillator's (UX2) frequency in Hz? */
-#define CONFIG_8260_CLKIN 66666600
-
-/*-----------------------------------------------------------------------
- * MODCK_H & MODCLK[1-3] - Ref: Section 9.2 in MPC8206 User Manual
- *-----------------------------------------------------------------------
- * What should MODCK_H be? It is dependent on the oscillator
- * frequency, MODCK[1-3], and desired CPM and core frequencies.
- * Here are some example values (all frequencies are in MHz):
- *
- * MODCK_H MODCK[1-3] Osc CPM Core S2-6 S2-7 S2-8
- * ------- ---------- --- --- ---- ----- ----- -----
- * 0x1 0x5 33 100 133 Open Close Open
- * 0x1 0x6 33 100 166 Open Open Close
- * 0x1 0x7 33 100 200 Open Open Open
- *
- * 0x2 0x2 33 133 133 Close Open Close
- * 0x2 0x3 33 133 166 Close Open Open
- * 0x2 0x4 33 133 200 Open Close Close
- * 0x2 0x5 33 133 233 Open Close Open
- * 0x2 0x6 33 133 266 Open Open Close
- *
- * 0x5 0x5 66 133 133 Open Close Open
- * 0x5 0x6 66 133 166 Open Open Close
- * 0x5 0x7 66 133 200 Open Open Open
- * 0x6 0x0 66 133 233 Close Close Close
- * 0x6 0x1 66 133 266 Close Close Open
- * 0x6 0x2 66 133 300 Close Open Close
- */
-#define CONFIG_SYS_SBC_MODCK_H 0x05
-
-/* Define this if you want to boot from 0x00000100. If you don't define
- * this, you will need to program the bootloader to 0xfff00000, and
- * get the hardware reset config words at 0xfe000000. The simplest
- * way to do that is to program the bootloader at both addresses.
- * It is suggested that you just let U-Boot live at 0x00000000.
- */
-#define CONFIG_SYS_SBC_BOOT_LOW 1
-
-/* What should the base address of the main FLASH be and how big is
- * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/sacsng/config.mk
- * The main FLASH is whichever is connected to *CS0.
- */
-#define CONFIG_SYS_FLASH0_BASE 0x40000000
-#define CONFIG_SYS_FLASH0_SIZE 2
-
-/* What should the base address of the secondary FLASH be and how big
- * is it (in Mbytes)? The secondary FLASH is whichever is connected
- * to *CS6.
- */
-#define CONFIG_SYS_FLASH1_BASE 0x60000000
-#define CONFIG_SYS_FLASH1_SIZE 2
-
-/* Define CONFIG_VERY_BIG_RAM to allow use of SDRAMs larger than 256MBytes
- */
-#define CONFIG_VERY_BIG_RAM 1
-
-/* What should be the base address of SDRAM DIMM and how big is
- * it (in Mbytes)? This will normally auto-configure via the SPD.
-*/
-#define CONFIG_SYS_SDRAM0_BASE 0x00000000
-#define CONFIG_SYS_SDRAM0_SIZE 64
-
-/*
- * Memory map example with 64 MB DIMM:
- *
- * 0x0000 0000 Exception Vector code, 8k
- * :
- * 0x0000 1FFF
- * 0x0000 2000 Free for Application Use
- * :
- * :
- *
- * :
- * :
- * 0x03F5 FF30 Monitor Stack (Growing downward)
- * Monitor Stack Buffer (0x80)
- * 0x03F5 FFB0 Board Info Data
- * 0x03F6 0000 Malloc Arena
- * : CONFIG_ENV_SECT_SIZE, 16k
- * : CONFIG_SYS_MALLOC_LEN, 128k
- * 0x03FC 0000 RAM Copy of Monitor Code
- * : CONFIG_SYS_MONITOR_LEN, 256k
- * 0x03FF FFFF [End of RAM], CONFIG_SYS_SDRAM_SIZE - 1
- */
-
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_CPU)
-
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere.
- */
-#define CONFIG_CONS_ON_SMC 1 /* define if console on SMC */
-#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on neither */
-#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-
-#undef CONFIG_ETHER_ON_SCC
-#define CONFIG_ETHER_ON_FCC
-#undef CONFIG_ETHER_NONE /* define if ethernet on neither */
-
-#ifdef CONFIG_ETHER_ON_SCC
-#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */
-#endif /* CONFIG_ETHER_ON_SCC */
-
-#ifdef CONFIG_ETHER_ON_FCC
-#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */
-#undef CONFIG_ETHER_LOOPBACK_TEST /* Ethernet external loopback test */
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
-/*
- * Port pins used for bit-banged MII communictions (if applicable).
- */
-
-#define MDIO_PORT 2 /* Port A=0, B=1, C=2, D=3 */
-#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
- (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
-#define MDC_DECLARE MDIO_DECLARE
-
-#define MDIO_ACTIVE (iop->pdir |= 0x40000000)
-#define MDIO_TRISTATE (iop->pdir &= ~0x40000000)
-#define MDIO_READ ((iop->pdat & 0x40000000) != 0)
-
-#define MDIO(bit) if(bit) iop->pdat |= 0x40000000; \
- else iop->pdat &= ~0x40000000
-
-#define MDC(bit) if(bit) iop->pdat |= 0x80000000; \
- else iop->pdat &= ~0x80000000
-
-#define MIIDELAY udelay(50)
-#endif /* CONFIG_ETHER_ON_FCC */
-
-#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1)
-
-/*
- * - RX clk is CLK11
- * - TX clk is CLK12
- */
-# define CONFIG_SYS_CMXSCR_VALUE1 (CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12)
-
-#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
-
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - Select bus for bd/buffers (see 28-13)
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE 0
-# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
-
-#define CONFIG_SHOW_BOOT_PROGRESS 1 /* boot progress enabled */
-
-/*
- * Configure for RAM tests.
- */
-#undef CONFIG_SYS_DRAM_TEST /* calls other tests in board.c */
-
-
-/*
- * Status LED for power up status feedback.
- */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
-#define STATUS_LED_PAR im_ioport.iop_ppara
-#define STATUS_LED_DIR im_ioport.iop_pdira
-#define STATUS_LED_ODR im_ioport.iop_podra
-#define STATUS_LED_DAT im_ioport.iop_pdata
-
-#define STATUS_LED_BIT 0x00000800 /* LED 0 is on PA.20 */
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ)
-#define STATUS_LED_STATE STATUS_LED_OFF
-#define STATUS_LED_BIT1 0x00001000 /* LED 1 is on PA.19 */
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ)
-#define STATUS_LED_STATE1 STATUS_LED_OFF
-#define STATUS_LED_BIT2 0x00002000 /* LED 2 is on PA.18 */
-#define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ/2)
-#define STATUS_LED_STATE2 STATUS_LED_ON
-
-#define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
-
-#define STATUS_LED_YELLOW 0
-#define STATUS_LED_GREEN 1
-#define STATUS_LED_RED 2
-#define STATUS_LED_BOOT 1
-
-
-/*
- * Select SPI support configuration
- */
-#define CONFIG_SOFT_SPI /* Enable SPI driver */
-#define MAX_SPI_BYTES 4 /* Maximum number of bytes we can handle */
-#undef DEBUG_SPI /* Disable SPI debugging */
-
-/*
- * Software (bit-bang) SPI driver configuration
- */
-#ifdef CONFIG_SOFT_SPI
-
-/*
- * Software (bit-bang) SPI driver configuration
- */
-#define I2C_SCLK 0x00002000 /* PD 18: Shift clock */
-#define I2C_MOSI 0x00004000 /* PD 17: Master Out, Slave In */
-#define I2C_MISO 0x00008000 /* PD 16: Master In, Slave Out */
-
-#define SPI_READ ((immr->im_ioport.iop_pdatd & I2C_MISO) != 0)
-#define SPI_SDA(bit) do { \
- if(bit) immr->im_ioport.iop_pdatd |= I2C_MOSI; \
- else immr->im_ioport.iop_pdatd &= ~I2C_MOSI; \
- } while (0)
-#define SPI_SCL(bit) do { \
- if(bit) immr->im_ioport.iop_pdatd |= I2C_SCLK; \
- else immr->im_ioport.iop_pdatd &= ~I2C_SCLK; \
- } while (0)
-#define SPI_DELAY /* No delay is needed */
-#endif /* CONFIG_SOFT_SPI */
-
-
-/*
- * select I2C support configuration
- *
- * Supported configurations are {none, software, hardware} drivers.
- * If the software driver is chosen, there are some additional
- * configuration items that the driver uses to drive the port pins.
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED 400000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE (iop->pdir |= 0x00010000)
-#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
-#define I2C_READ ((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
- else iop->pdat &= ~0x00010000
-#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
- else iop->pdat &= ~0x00020000
-#define I2C_DELAY udelay(20) /* 1/4 I2C clock duration */
-
-/* Define this to reserve an entire FLASH sector for
- * environment variables. Otherwise, the environment will be
- * put in the same sector as U-Boot, and changing variables
- * will erase U-Boot temporarily
- */
-#define CONFIG_ENV_IN_OWN_SECT 1
-
-/* Define this to contain any number of null terminated strings that
- * will be part of the default environment compiled into the boot image.
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
-"quiet=0\0" \
-"serverip=192.168.123.205\0" \
-"ipaddr=192.168.123.203\0" \
-"checkhostname=VR8500\0" \
-"reprog="\
- "bootp; " \
- "tftpboot 0x140000 /bdi2000/u-boot.bin; " \
- "protect off 60000000 6003FFFF; " \
- "erase 60000000 6003FFFF; " \
- "cp.b 140000 60000000 ${filesize}; " \
- "protect on 60000000 6003FFFF\0" \
-"copyenv="\
- "protect off 60040000 6004FFFF; " \
- "erase 60040000 6004FFFF; " \
- "cp.b 40040000 60040000 10000; " \
- "protect on 60040000 6004FFFF\0" \
-"copyprog="\
- "protect off 60000000 6003FFFF; " \
- "erase 60000000 6003FFFF; " \
- "cp.b 40000000 60000000 40000; " \
- "protect on 60000000 6003FFFF\0" \
-"zapenv="\
- "protect off 40040000 4004FFFF; " \
- "erase 40040000 4004FFFF; " \
- "protect on 40040000 4004FFFF\0" \
-"zapotherenv="\
- "protect off 60040000 6004FFFF; " \
- "erase 60040000 6004FFFF; " \
- "protect on 60040000 6004FFFF\0" \
-"root-on-initrd="\
- "setenv bootcmd "\
- "version\\;" \
- "echo\\;" \
- "bootp\\;" \
- "setenv bootargs root=/dev/ram0 rw quiet " \
- "ip=\\${ipaddr}:\\${serverip}:\\${gatewayip}:\\${netmask}:\\${hostname}::off\\;" \
- "run boot-hook\\;" \
- "bootm\0" \
-"root-on-initrd-debug="\
- "setenv bootcmd "\
- "version\\;" \
- "echo\\;" \
- "bootp\\;" \
- "setenv bootargs root=/dev/ram0 rw debug " \
- "ip=\\${ipaddr}:\\${serverip}:\\${gatewayip}:\\${netmask}:\\${hostname}::off\\;" \
- "run debug-hook\\;" \
- "run boot-hook\\;" \
- "bootm\0" \
-"root-on-nfs="\
- "setenv bootcmd "\
- "version\\;" \
- "echo\\;" \
- "bootp\\;" \
- "setenv bootargs root=/dev/nfs rw quiet " \
- "nfsroot=\\${serverip}:\\${rootpath} " \
- "ip=\\${ipaddr}:\\${serverip}:\\${gatewayip}:\\${netmask}:\\${hostname}::off\\;" \
- "run boot-hook\\;" \
- "bootm\0" \
-"root-on-nfs-debug="\
- "setenv bootcmd "\
- "version\\;" \
- "echo\\;" \
- "bootp\\;" \
- "setenv bootargs root=/dev/nfs rw debug " \
- "nfsroot=\\${serverip}:\\${rootpath} " \
- "ip=\\${ipaddr}:\\${serverip}:\\${gatewayip}:\\${netmask}:\\${hostname}::off\\;" \
- "run debug-hook\\;" \
- "run boot-hook\\;" \
- "bootm\0" \
-"debug-checkout="\
- "setenv checkhostname;" \
- "setenv ethaddr 00:09:70:00:00:01;" \
- "bootp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} debug " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "run debug-hook;" \
- "run boot-hook;" \
- "bootm\0" \
-"debug-hook="\
- "echo ipaddr ${ipaddr};" \
- "echo serverip ${serverip};" \
- "echo gatewayip ${gatewayip};" \
- "echo netmask ${netmask};" \
- "echo hostname ${hostname}\0" \
-"ana=run adc ; run dac\0" \
-"adc=run adc-12 ; run adc-34\0" \
-"adc-12=echo ### ADC-12 ; i2c md e 81 e\0" \
-"adc-34=echo ### ADC-34 ; i2c md f 81 e\0" \
-"dac=echo ### DAC ; i2c md 11 81 5\0" \
-"boot-hook=echo\0"
-
-/* What should the console's baud rate be? */
-#define CONFIG_BAUDRATE 9600
-
-/* Ethernet MAC address */
-#define CONFIG_ETHADDR 00:09:70:00:00:00
-
-/* The default Ethernet MAC address can be overwritten just once */
-#ifdef CONFIG_ETHADDR
-#define CONFIG_OVERWRITE_ETHADDR_ONCE 1
-#endif
-
-/*
- * Define this to do some miscellaneous board-specific initialization.
- */
-#define CONFIG_MISC_INIT_R
-
-/* Set to a positive value to delay for running BOOTCOMMAND */
-#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
-
-/* Be selective on what keys can delay or stop the autoboot process
- * To stop use: " "
- */
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT "Autobooting...\n"
-#define CONFIG_AUTOBOOT_STOP_STR " "
-#undef CONFIG_AUTOBOOT_DELAY_STR
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#define DEBUG_BOOTKEYS 0
-
-/* Define a command string that is automatically executed when no character
- * is read on the console interface withing "Boot Delay" after reset.
- */
-#undef CONFIG_BOOT_ROOT_INITRD /* Use ram disk for the root file system */
-#define CONFIG_BOOT_ROOT_NFS /* Use a NFS mounted root file system */
-
-#ifdef CONFIG_BOOT_ROOT_INITRD
-#define CONFIG_BOOTCOMMAND \
- "version;" \
- "echo;" \
- "bootp;" \
- "setenv bootargs root=/dev/ram0 rw quiet " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "run boot-hook;" \
- "bootm"
-#endif /* CONFIG_BOOT_ROOT_INITRD */
-
-#ifdef CONFIG_BOOT_ROOT_NFS
-#define CONFIG_BOOTCOMMAND \
- "version;" \
- "echo;" \
- "bootp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} quiet " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "run boot-hook;" \
- "bootm"
-#endif /* CONFIG_BOOT_ROOT_NFS */
-
-#define CONFIG_BOOTP_RANDOM_DELAY /* Randomize the BOOTP retry delay */
-#define CONFIG_LIB_RAND
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-
-
-/* undef this to save memory */
-#define CONFIG_SYS_LONGHELP
-
-/* Monitor Command Prompt */
-
-#undef CONFIG_SYS_HUSH_PARSER
-#ifdef CONFIG_SYS_HUSH_PARSER
-#endif
-
-/* When CONFIG_TIMESTAMP is selected, the timestamp (date and time)
- * of an image is printed by image commands like bootm or iminfo.
- */
-#define CONFIG_TIMESTAMP
-
-/* If this variable is defined, an environment variable named "ver"
- * is created by U-Boot showing the U-Boot version.
- */
-#define CONFIG_VERSION_VARIABLE
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_SPI
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-
-#undef CONFIG_CMD_KGDB
-
-#ifdef CONFIG_ETHER_ON_FCC
-#define CONFIG_CMD_MII
-#endif
-
-
-/* Where do the internal registers live? */
-#define CONFIG_SYS_IMMR 0xF0000000
-
-#undef CONFIG_WATCHDOG /* disable the watchdog */
-
-/*****************************************************************************
- *
- * You should not have to modify any of the following settings
- *
- *****************************************************************************/
-
-#define CONFIG_SACSng 1 /* munged for the SACSng */
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_BOOTM_HEADER_QUIET 1 /* Suppress the image header dump */
- /* in the bootm command. */
-#define CONFIG_SYS_BOOTM_PROGESS_QUIET 1 /* Suppress the progress displays, */
- /* "## <message>" from the bootm cmd */
-#define CONFIG_SYS_BOOTP_CHECK_HOSTNAME 1 /* If checkhostname environment is */
- /* defined, then the hostname param */
- /* validated against checkhostname. */
-#define CONFIG_SYS_BOOTP_RETRY_COUNT 0x40000000 /* # of timeouts before giving up */
-#define CONFIG_SYS_BOOTP_SHORT_RANDOM_DELAY 1 /* Use a short random delay value */
- /* (limited to maximum of 1024 msec) */
-#define CONFIG_SYS_CHK_FOR_ABORT_AT_LEAST_ONCE 1
- /* Check for abort key presses */
- /* at least once in dependent of the */
- /* CONFIG_BOOTDELAY value. */
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Don't print console @ startup */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 1 /* Echo the inverted Ethernet link */
- /* state to the fault LED. */
-#define CONFIG_SYS_FAULT_MII_ADDR 0x02 /* MII addr of the PHY to check for */
- /* the Ethernet link state. */
-#define CONFIG_SYS_STATUS_FLASH_UNTIL_TFTP_OK 1 /* Keeping the status LED flashing */
- /* until the TFTP is successful. */
-#define CONFIG_SYS_STATUS_OFF_AFTER_NETBOOT 1 /* After a successful netboot, */
- /* turn off the STATUS LEDs. */
-#define CONFIG_SYS_TFTP_BLINK_STATUS_ON_DATA_IN 1 /* Blink status LED based on */
- /* incoming data. */
-#define CONFIG_SYS_TFTP_BLOCKS_PER_HASH 100 /* For every XX blocks, output a '#' */
- /* to signify that tftp is moving. */
-#define CONFIG_SYS_TFTP_HASHES_PER_FLASH 200 /* For every '#' hashes, */
- /* flash the status LED. */
-#define CONFIG_SYS_TFTP_HASHES_PER_LINE 65 /* Only output XX '#'s per line */
- /* during the tftp file transfer. */
-#define CONFIG_SYS_TFTP_PROGESS_QUIET 1 /* Suppress the progress displays */
- /* '#'s from the tftp command. */
-#define CONFIG_SYS_TFTP_STATUS_QUIET 1 /* Suppress the status displays */
- /* issued during the tftp command. */
-#define CONFIG_SYS_TFTP_TIMEOUT_COUNT 5 /* How many timeouts TFTP will allow */
- /* before it gives up. */
-
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-
-#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
-
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
-
-#define CONFIG_SYS_ALT_MEMTEST /* Select full-featured memory test */
-#define CONFIG_SYS_MEMTEST_START 0x2000 /* memtest works from the end of */
- /* the exception vector table */
- /* to the end of the DRAM */
- /* less monitor and malloc area */
-#define CONFIG_SYS_STACK_USAGE 0x10000 /* Reserve 64k for the stack usage */
-#define CONFIG_SYS_MEM_END_USAGE ( CONFIG_SYS_MONITOR_LEN \
- + CONFIG_SYS_MALLOC_LEN \
- + CONFIG_ENV_SECT_SIZE \
- + CONFIG_SYS_STACK_USAGE )
-
-#define CONFIG_SYS_MEMTEST_END ( CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 \
- - CONFIG_SYS_MEM_END_USAGE )
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE
-#define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_SDRAM0_SIZE
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- */
-#if defined(CONFIG_SYS_SBC_BOOT_LOW)
-# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
-#else
-# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0)
-#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */
-
-/* get the HRCW ISB field from CONFIG_SYS_IMMR */
-#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) | \
- ((CONFIG_SYS_IMMR & 0x01000000) >> 7) | \
- ((CONFIG_SYS_IMMR & 0x00100000) >> 4) )
-
-#define CONFIG_SYS_HRCW_MASTER ( HRCW_BPS10 | \
- HRCW_DPPC11 | \
- CONFIG_SYS_SBC_HRCW_IMMR | \
- HRCW_MMR00 | \
- HRCW_LBPC11 | \
- HRCW_APPC10 | \
- HRCW_CS10PC00 | \
- (CONFIG_SYS_SBC_MODCK_H & HRCW_MODCK_H1111) | \
- CONFIG_SYS_SBC_HRCW_BOOT_FLAGS )
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH0_BASE
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#undef CONFIG_SYS_FLASH_PROTECTION /* use hardware protection */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT (64+4) /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
-
-#ifndef CONFIG_SYS_RAMBOOT
-# define CONFIG_ENV_IS_IN_FLASH 1
-
-# ifdef CONFIG_ENV_IN_OWN_SECT
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-# define CONFIG_ENV_SECT_SIZE 0x10000
-# else
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
-# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-# define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */
-# endif /* CONFIG_ENV_IN_OWN_SECT */
-
-#else
-# define CONFIG_ENV_IS_IN_NVRAM 1
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-# define CONFIG_ENV_SIZE 0x200
-#endif /* CONFIG_SYS_RAMBOOT */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT (HID0_ICE |\
- HID0_DCE |\
- HID0_ICFI |\
- HID0_DCI |\
- HID0_IFEM |\
- HID0_ABE)
-
-#define CONFIG_SYS_HID0_FINAL (HID0_ICE |\
- HID0_IFEM |\
- HID0_ABE |\
- HID0_EMCP)
-#define CONFIG_SYS_HID2 0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RMR 0
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration 4-25
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_BCR (BCR_ETM)
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 4-31
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC11 |\
- SIUMCR_L2CPC00 |\
- SIUMCR_APPC10 |\
- SIUMCR_MMR00)
-
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
- SYPCR_BMT |\
- SYPCR_PBME |\
- SYPCR_LBME |\
- SYPCR_SWRI |\
- SYPCR_SWP |\
- SYPCR_SWE)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
- SYPCR_BMT |\
- SYPCR_PBME |\
- SYPCR_LBME |\
- SYPCR_SWRI |\
- SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\
- TMCNTSC_ALR |\
- TMCNTSC_TCF |\
- TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR (PISCR_PS |\
- PISCR_PTF |\
- PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control 9-8
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SCCR 0
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration 13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR 0
-
-/*
- * Initialize Memory Controller:
- *
- * Bank Bus Machine PortSz Device
- * ---- --- ------- ------ ------
- * 0 60x GPCM 16 bit FLASH (primary flash - 2MB)
- * 1 60x GPCM -- bit (Unused)
- * 2 60x SDRAM 64 bit SDRAM (DIMM)
- * 3 60x SDRAM 64 bit SDRAM (DIMM)
- * 4 60x GPCM -- bit (Unused)
- * 5 60x GPCM -- bit (Unused)
- * 6 60x GPCM 16 bit FLASH (secondary flash - 2MB)
- */
-
-/*-----------------------------------------------------------------------
- * BR0,BR1 - Base Register
- * Ref: Section 10.3.1 on page 10-14
- * OR0,OR1 - Option Register
- * Ref: Section 10.3.2 on page 10-18
- *-----------------------------------------------------------------------
- */
-
-/* Bank 0 - Primary FLASH
- */
-
-/* BR0 is configured as follows:
- *
- * - Base address of 0x40000000
- * - 16 bit port size
- * - Data errors checking is disabled
- * - Read and write access
- * - GPCM 60x bus
- * - Access are handled by the memory controller according to MSEL
- * - Not used for atomic operations
- * - No data pipelining is done
- * - Valid
- */
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\
- BRx_PS_16 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-/* OR0 is configured as follows:
- *
- * - 4 MB
- * - *BCTL0 is asserted upon access to the current memory bank
- * - *CW / *WE are negated a quarter of a clock earlier
- * - *CS is output at the same time as the address lines
- * - Uses a clock cycle length of 5
- * - *PSDVAL is generated internally by the memory controller
- * unless *GTA is asserted earlier externally.
- * - Relaxed timing is generated by the GPCM for accesses
- * initiated to this memory region.
- * - One idle clock is inserted between a read access from the
- * current bank and the next access.
- */
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxG_TRLX |\
- ORxG_EHTR)
-
-/*-----------------------------------------------------------------------
- * BR2,BR3 - Base Register
- * Ref: Section 10.3.1 on page 10-14
- * OR2,OR3 - Option Register
- * Ref: Section 10.3.2 on page 10-16
- *-----------------------------------------------------------------------
- */
-
-/* Bank 2,3 - SDRAM DIMM
- */
-
-/* The BR2 is configured as follows:
- *
- * - Base address of 0x00000000
- * - 64 bit port size (60x bus only)
- * - Data errors checking is disabled
- * - Read and write access
- * - SDRAM 60x bus
- * - Access are handled by the memory controller according to MSEL
- * - Not used for atomic operations
- * - No data pipelining is done
- * - Valid
- */
-#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-/* With a 64 MB DIMM, the OR2 is configured as follows:
- *
- * - 64 MB
- * - 4 internal banks per device
- * - Row start address bit is A8 with PSDMR[PBI] = 0
- * - 12 row address lines
- * - Back-to-back page mode
- * - Internal bank interleaving within save device enabled
- */
-#if (CONFIG_SYS_SDRAM0_SIZE == 64)
-#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A8 |\
- ORxS_NUMR_12)
-#else
-#error "INVALID SDRAM CONFIGURATION"
-#endif
-
-/*-----------------------------------------------------------------------
- * PSDMR - 60x Bus SDRAM Mode Register
- * Ref: Section 10.3.3 on page 10-21
- *-----------------------------------------------------------------------
- */
-
-/* Address that the DIMM SPD memory lives at.
- */
-#define SDRAM_SPD_ADDR 0x50
-
-#if (CONFIG_SYS_SDRAM0_SIZE == 64)
-/* With a 64 MB DIMM, the PSDMR is configured as follows:
- *
- * - Bank Based Interleaving,
- * - Refresh Enable,
- * - Address Multiplexing where A5 is output on A14 pin
- * (A6 on A15, and so on),
- * - use address pins A14-A16 as bank select,
- * - A9 is output on SDA10 during an ACTIVATE command,
- * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks,
- * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command
- * is 3 clocks,
- * - earliest timing for READ/WRITE command after ACTIVATE command is
- * 2 clocks,
- * - earliest timing for PRECHARGE after last data was read is 1 clock,
- * - earliest timing for PRECHARGE after last data was written is 1 clock,
- * - CAS Latency is 2.
- */
-#define CONFIG_SYS_PSDMR (PSDMR_RFEN |\
- PSDMR_SDAM_A14_IS_A5 |\
- PSDMR_BSMA_A14_A16 |\
- PSDMR_SDA10_PBI0_A9 |\
- PSDMR_RFRC_7_CLK |\
- PSDMR_PRETOACT_3W |\
- PSDMR_ACTTORW_2W |\
- PSDMR_LDOTOPRE_1C |\
- PSDMR_WRC_1C |\
- PSDMR_CL_2)
-#else
-#error "INVALID SDRAM CONFIGURATION"
-#endif
-
-/*
- * Shoot for approximately 1MHz on the prescaler.
- */
-#if (CONFIG_8260_CLKIN >= (60 * 1000 * 1000))
-#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV64
-#elif (CONFIG_8260_CLKIN >= (30 * 1000 * 1000))
-#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV32
-#else
-#warning "Unconfigured bus clock freq: check CONFIG_SYS_MPTPR and CONFIG_SYS_PSRT are OK"
-#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV32
-#endif
-#define CONFIG_SYS_PSRT 14
-
-
-/*-----------------------------------------------------------------------
- * BR6 - Base Register
- * Ref: Section 10.3.1 on page 10-14
- * OR6 - Option Register
- * Ref: Section 10.3.2 on page 10-18
- *-----------------------------------------------------------------------
- */
-
-/* Bank 6 - Secondary FLASH
- *
- * The secondary FLASH is connected to *CS6
- */
-#if (defined(CONFIG_SYS_FLASH1_BASE) && defined(CONFIG_SYS_FLASH1_SIZE))
-
-/* BR6 is configured as follows:
- *
- * - Base address of 0x60000000
- * - 16 bit port size
- * - Data errors checking is disabled
- * - Read and write access
- * - GPCM 60x bus
- * - Access are handled by the memory controller according to MSEL
- * - Not used for atomic operations
- * - No data pipelining is done
- * - Valid
- */
-# define CONFIG_SYS_BR6_PRELIM ((CONFIG_SYS_FLASH1_BASE & BRx_BA_MSK) |\
- BRx_PS_16 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-/* OR6 is configured as follows:
- *
- * - 2 MB
- * - *BCTL0 is asserted upon access to the current memory bank
- * - *CW / *WE are negated a quarter of a clock earlier
- * - *CS is output at the same time as the address lines
- * - Uses a clock cycle length of 5
- * - *PSDVAL is generated internally by the memory controller
- * unless *GTA is asserted earlier externally.
- * - Relaxed timing is generated by the GPCM for accesses
- * initiated to this memory region.
- * - One idle clock is inserted between a read access from the
- * current bank and the next access.
- */
-# define CONFIG_SYS_OR6_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH1_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxG_TRLX |\
- ORxG_EHTR)
-#endif /* (defined(CONFIG_SYS_FLASH1_BASE) && defined(CONFIG_SYS_FLASH1_SIZE)) */
-
-#endif /* __CONFIG_H */