-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-#endif /* CONFIG_HERMES */
-
-/*** IAD210 **********************************************************/
-
-/* The IAD210 uses the FEC on a MPC860P for Ethernet */
-
-#if defined(CONFIG_IAD210)
-
-# define FEC_ENET /* use FEC for Ethernet */
-# undef SCC_ENET
-
-# define PD_MII_TXD1 ((ushort) 0x1000 ) /* PD 3 */
-# define PD_MII_TXD2 ((ushort) 0x0800 ) /* PD 4 */
-# define PD_MII_TXD3 ((ushort) 0x0400 ) /* PD 5 */
-# define PD_MII_RX_DV ((ushort) 0x0200 ) /* PD 6 */
-# define PD_MII_RX_ERR ((ushort) 0x0100 ) /* PD 7 */
-# define PD_MII_RX_CLK ((ushort) 0x0080 ) /* PD 8 */
-# define PD_MII_TXD0 ((ushort) 0x0040 ) /* PD 9 */
-# define PD_MII_RXD0 ((ushort) 0x0020 ) /* PD 10 */
-# define PD_MII_TX_ERR ((ushort) 0x0010 ) /* PD 11 */
-# define PD_MII_MDC ((ushort) 0x0008 ) /* PD 12 */
-# define PD_MII_RXD1 ((ushort) 0x0004 ) /* PD 13 */
-# define PD_MII_RXD2 ((ushort) 0x0002 ) /* PD 14 */
-# define PD_MII_RXD3 ((ushort) 0x0001 ) /* PD 15 */
-
-# define PD_MII_MASK ((ushort) 0x1FFF ) /* PD 3...15 */
-
-#endif /* CONFIG_IAD210 */
-
-/*** ICU862 **********************************************************/
-
-#if defined(CONFIG_ICU862)
-
-#ifdef CONFIG_FEC_ENET
-#define FEC_ENET /* use FEC for EThernet */
-#endif /* CONFIG_FEC_ETHERNET */
-
-#endif /* CONFIG_ICU862 */
-
-/*** IP860 **********************************************************/
-
-#if defined(CONFIG_IP860)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
-#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0100) /* PA 7 */
-
-#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
-#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
-#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
-
-#define PB_ENET_RESET (uint)0x00000008 /* PB 28 */
-#define PB_ENET_JABD (uint)0x00000004 /* PB 29 */
-
-/* Control bits in the SICR to route TCLK (CLK1) and RCLK (CLK2) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000002C)
-#endif /* CONFIG_IP860 */
-
-/*** IVMS8 **********************************************************/
-
-/* The IVMS8 uses the FEC on a MPC860T for Ethernet */
-
-#if defined(CONFIG_IVMS8) || defined(CONFIG_IVML24)
-
-#define FEC_ENET /* use FEC for EThernet */
-#undef SCC_ENET
-
-#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */
-
-#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-#endif /* CONFIG_IVMS8, CONFIG_IVML24 */
-
-/*** KUP4K, KUP4X ****************************************************/
-/* The KUP4 boards uses the FEC on a MPC8xx for Ethernet */
-
-#if defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
-
-#define FEC_ENET /* use FEC for EThernet */
-#undef SCC_ENET
-
-#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */
-
-#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-#endif /* CONFIG_KUP4K */
-
-
-/*** LANTEC *********************************************************/
-
-#if defined(CONFIG_LANTEC) && CONFIG_LANTEC >= 2
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_LBK ((ushort)0x0010) /* PC 11 */
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000FF00)
-#define SICR_ENET_CLKRT ((uint)0x00002E00)
-#endif /* CONFIG_LANTEC v2 */
-
-/*** LWMON **********************************************************/
-
-#if defined(CONFIG_LWMON)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0800) /* PA 4 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK4) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003E00)
-#endif /* CONFIG_LWMON */
-
-/*** NX823 ***********************************************/
-
-#if defined(CONFIG_NX823)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002f00)
-
-#endif /* CONFIG_NX823 */
-
-/*** MBX ************************************************************/
-
-#ifdef CONFIG_MBX
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use. The TCLK and RCLK seem unique
- * to the MBX860 board. Any two of the four available clocks could be
- * used, and the MPC860 cookbook manual has an example using different
- * clock pins.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001)
-#define PA_ENET_TXD ((ushort)0x0002)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PC_ENET_TENA ((ushort)0x0001)
-#define PC_ENET_CLSN ((ushort)0x0010)
-#define PC_ENET_RENA ((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000003d)
-#endif /* CONFIG_MBX */
-
-/*** KM8XX *********************************************************/
-
-/* The KM8XX Service Module uses SCC3 for Ethernet */
-
-#ifdef CONFIG_KM8XX
-#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
-#define CPM_CR_ENET CPM_CR_CH_SCC3
-#define SCC_ENET 2
-#define PA_ENET_RXD ((ushort)0x0010) /* PA 11 */
-#define PA_ENET_TXD ((ushort)0x0020) /* PA 10 */
-#define PA_ENET_RCLK ((ushort)0x1000) /* PA 3 CLK 5 */
-#define PA_ENET_TCLK ((ushort)0x2000) /* PA 2 CLK 6 */
-
-#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
-
-#define PC_ENET_RENA ((ushort)0x0200) /* PC 6 */
-#define PC_ENET_CLSN ((ushort)0x0100) /* PC 7 */
-
-/* Control bits in the SICR to route TCLK (CLK6) and RCLK (CLK5) to
- * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x00FF0000)
-#define SICR_ENET_CLKRT ((uint)0x00250000)
-#endif /* CONFIG_KM8XX */
-
-
-/*** MHPC ********************************************************/
-
-#if defined(CONFIG_MHPC)
-/* This ENET stuff is for the MHPC with ethernet on SCC2.
- * Note TENA is on Port B.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002e00) /* RCLK-CLK2, TCLK-CLK3 */
-#endif /* CONFIG_MHPC */
-
-/*** NETVIA *******************************************************/
-
-/* SinoVee Microsystems SC8xx series FEL8xx-AT,SC823,SC850,SC855T,SC860T */
-#if ( defined CONFIG_SVM_SC8xx )
-# ifndef CONFIG_FEC_ENET
-
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-
- /* Bits in parallel I/O port registers that have to be set/cleared
- * * * * to configure the pins for SCC2 use.
- * * * */
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0400) /* PA 5 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * * * * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- * * * */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003700)
-
-# else /* Use FEC for Fast Ethernet */
-
-#undef SCC_ENET
-#define FEC_ENET
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-# endif /* CONFIG_FEC_ENET */
-#endif /* CONFIG_SVM_SC8xx */
-
-
-#if defined(CONFIG_NETVIA)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
-
-#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1
-# define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */
-#elif CONFIG_NETVIA_VERSION >= 2
-# define PC_ENET_PDN ((ushort)0x0008) /* PC 12 */
-#endif
-
-#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002f00)
-
-#endif /* CONFIG_NETVIA */
-
-/*** QS850/QS823 ***************************************************/
-
-#if defined(CONFIG_QS850) || defined(CONFIG_QS823)
-#undef FEC_ENET /* Don't use FEC for EThernet */
-
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-
-#define PA_ENET_RXD ((ushort)0x0004) /* RXD on PA13 (Pin D9) */
-#define PA_ENET_TXD ((ushort)0x0008) /* TXD on PA12 (Pin D7) */
-#define PC_ENET_RENA ((ushort)0x0080) /* RENA on PC8 (Pin D12) */
-#define PC_ENET_CLSN ((ushort)0x0040) /* CLSN on PC9 (Pin C12) */
-#define PA_ENET_TCLK ((ushort)0x0200) /* TCLK on PA6 (Pin D8) */
-#define PA_ENET_RCLK ((ushort)0x0800) /* RCLK on PA4 (Pin D10) */
-#define PB_ENET_TENA ((uint)0x00002000) /* TENA on PB18 (Pin D11) */
-#define PC_ENET_LBK ((ushort)0x0010) /* Loopback control on PC11 (Pin B14) */
-#define PC_ENET_LI ((ushort)0x0020) /* Link Integrity control PC10 (A15) */
-#define PC_ENET_SQE ((ushort)0x0100) /* SQE Disable control PC7 (B15) */
-
-/* SCC2 TXCLK from CLK2
- * SCC2 RXCLK from CLK4
- * SCC2 Connected to NMSI */
-#define SICR_ENET_MASK ((uint)0x00007F00)
-#define SICR_ENET_CLKRT ((uint)0x00003D00)
-
-#endif /* CONFIG_QS850/QS823 */
-
-/*** QS860T ***************************************************/
-
-#ifdef CONFIG_QS860T
-#ifdef CONFIG_FEC_ENET
-#define FEC_ENET /* use FEC for EThernet */
-#endif /* CONFIG_FEC_ETHERNET */
-
-/* This ENET stuff is for GTH 10 Mbit ( SCC ) */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-
-#define PA_ENET_RXD ((ushort)0x0001) /* PA15 */
-#define PA_ENET_TXD ((ushort)0x0002) /* PA14 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA4 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA6 */
-#define PB_ENET_TENA ((uint)0x00001000) /* PB19 */
-#define PC_ENET_CLSN ((ushort)0x0010) /* PC11 */
-#define PC_ENET_RENA ((ushort)0x0020) /* PC10 */
-
-#define SICR_ENET_MASK ((uint)0x000000ff)
-/* RCLK PA4 -->CLK4, TCLK PA6 -->CLK2 */
-#define SICR_ENET_CLKRT ((uint)0x0000003D)
-
-#endif /* CONFIG_QS860T */
-
-/*** RPXCLASSIC *****************************************************/
-
-#ifdef CONFIG_RPXCLASSIC
-
-#ifdef CONFIG_FEC_ENET
-
-# define FEC_ENET /* use FEC for EThernet */
-# undef SCC_ENET
-
-#else /* ! CONFIG_FEC_ENET */
-
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001)
-#define PA_ENET_TXD ((ushort)0x0002)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PB_ENET_TENA ((uint)0x00001000)
-#define PC_ENET_CLSN ((ushort)0x0010)
-#define PC_ENET_RENA ((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000003d)
-
-#endif /* CONFIG_FEC_ENET */
-
-#endif /* CONFIG_RPXCLASSIC */
-
-/*** RPXLITE ********************************************************/
-
-#ifdef CONFIG_RPXLITE
-/* This ENET stuff is for the MPC850 with ethernet on SCC2. Some of
- * this may be unique to the RPX-Lite configuration.
- * Note TENA is on Port B.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#if defined(CONFIG_RMU)
-#define PC_ENET_TENA ((uint)0x00000002) /* PC14 */
-#else
-#define PB_ENET_TENA ((uint)0x00002000)
-#endif
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003d00)
-#endif /* CONFIG_RPXLITE */
-
-/*** SM850 *********************************************************/
-
-/* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */
-
-#ifdef CONFIG_SM850
-#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
-#define CPM_CR_ENET CPM_CR_CH_SCC3
-#define SCC_ENET 2
-#define PB_ENET_RXD ((uint)0x00000004) /* PB 29 */
-#define PB_ENET_TXD ((uint)0x00000002) /* PB 30 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
-#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
-
-#define PC_ENET_RENA ((ushort)0x0800) /* PC 4 */
-#define PC_ENET_CLSN ((ushort)0x0400) /* PC 5 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x00FF0000)
-#define SICR_ENET_CLKRT ((uint)0x00260000)
-#endif /* CONFIG_SM850 */
-
-/*** SPD823TS ******************************************************/
-
-#ifdef CONFIG_SPD823TS
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2 /* Ethernet on SCC2 */
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_MDC ((ushort)0x0001) /* PA 15 !!! */
-#define PA_ENET_MDIO ((ushort)0x0002) /* PA 14 !!! */
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 !!! */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002E00)
-#endif /* CONFIG_SPD823TS */
-
-/*** SXNI855T ******************************************************/
-
-#if defined(CONFIG_SXNI855T)
-
-#ifdef CONFIG_FEC_ENET
-#define FEC_ENET /* use FEC for Ethernet */
-#endif /* CONFIG_FEC_ETHERNET */
-
-#endif /* CONFIG_SXNI855T */
-
-/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, ETX094, R360MPI **********/
-
-#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
- defined(CONFIG_R360MPI) || defined(CONFIG_RBC823) || \
- defined(CONFIG_TQM823L) || defined(CONFIG_TQM823M) || \
- defined(CONFIG_TQM850L) || defined(CONFIG_TQM850M) || \
- defined(CONFIG_TQM885D) || defined(CONFIG_ETX094) || \
- defined(CONFIG_RRVISION)|| defined(CONFIG_VIRTLAB2)|| \
- (defined(CONFIG_LANTEC) && CONFIG_LANTEC < 2)
-
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#if (!defined(CONFIG_TK885D)) /* TK885D does not use SCC Ethernet */
-#define SCC_ENET 1
-#endif
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-#if defined(CONFIG_R360MPI)
-#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
-#endif /* CONFIG_R360MPI */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002600)
-
-# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
-#define FEC_ENET
-# endif /* CONFIG_FEC_ENET */
-
-#endif /* CONFIG_MVS v1, CONFIG_TQM823L/M, CONFIG_TQM850L/M, etc. */
-
-/*** TQM855L/M, TQM860L/M, TQM862L/M, TQM866L/M *********************/
-
-#if defined(CONFIG_TQM855L) || defined(CONFIG_TQM855M) || \
- defined(CONFIG_TQM860L) || defined(CONFIG_TQM860M) || \
- defined(CONFIG_TQM862L) || defined(CONFIG_TQM862M) || \
- defined(CONFIG_TQM866L) || defined(CONFIG_TQM866M)
-
-# ifdef CONFIG_SCC1_ENET /* use SCC for 10Mbps Ethernet */
-
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
-#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
-#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
-#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x00000026)
-
-# endif /* CONFIG_SCC1_ENET */
-
-# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
-
-#define FEC_ENET