+#ifdef CONFIG_SPI_FLASH_SPANSION
+static int s25hx_t_mdp_ready(struct spi_nor *nor)
+{
+ u32 addr;
+ int ret;
+
+ for (addr = 0; addr < nor->mtd.size; addr += SZ_128M) {
+ ret = spansion_sr_ready(nor, addr, 0);
+ if (!ret)
+ return ret;
+ }
+
+ return 1;
+}
+
+static int s25hx_t_quad_enable(struct spi_nor *nor)
+{
+ u32 addr;
+ int ret;
+
+ for (addr = 0; addr < nor->mtd.size; addr += SZ_128M) {
+ ret = spansion_quad_enable_volatile(nor, addr, 0);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int s25hx_t_erase_non_uniform(struct spi_nor *nor, loff_t addr)
+{
+ /* Support 32 x 4KB sectors at bottom */
+ return spansion_erase_non_uniform(nor, addr, SPINOR_OP_BE_4K_4B, 0,
+ SZ_128K);
+}
+
+static int s25hx_t_setup(struct spi_nor *nor, const struct flash_info *info,
+ const struct spi_nor_flash_parameter *params)
+{
+ int ret;
+ u8 cfr3v;
+
+#ifdef CONFIG_SPI_FLASH_BAR
+ return -ENOTSUPP; /* Bank Address Register is not supported */
+#endif
+ /*
+ * Read CFR3V to check if uniform sector is selected. If not, assign an
+ * erase hook that supports non-uniform erase.
+ */
+ ret = spansion_read_any_reg(nor, SPINOR_REG_ADDR_CFR3V, 0, &cfr3v);
+ if (ret)
+ return ret;
+ if (!(cfr3v & CFR3V_UNHYSA))
+ nor->erase = s25hx_t_erase_non_uniform;
+
+ /*
+ * For the multi-die package parts, the ready() hook is needed to check
+ * all dies' status via read any register.
+ */
+ if (nor->mtd.size > SZ_128M)
+ nor->ready = s25hx_t_mdp_ready;
+
+ return spi_nor_default_setup(nor, info, params);
+}
+
+static void s25hx_t_default_init(struct spi_nor *nor)
+{
+ nor->setup = s25hx_t_setup;
+}
+
+static int s25hx_t_post_bfpt_fixup(struct spi_nor *nor,
+ const struct sfdp_parameter_header *header,
+ const struct sfdp_bfpt *bfpt,
+ struct spi_nor_flash_parameter *params)
+{
+ int ret;
+ u32 addr;
+ u8 cfr3v;
+
+ /* erase size in case it is set to 4K from BFPT */
+ nor->erase_opcode = SPINOR_OP_SE_4B;
+ nor->mtd.erasesize = nor->info->sector_size;
+
+ ret = set_4byte(nor, nor->info, 1);
+ if (ret)
+ return ret;
+ nor->addr_width = 4;
+
+ /*
+ * The page_size is set to 512B from BFPT, but it actually depends on
+ * the configuration register. Look up the CFR3V and determine the
+ * page_size. For multi-die package parts, use 512B only when the all
+ * dies are configured to 512B buffer.
+ */
+ for (addr = 0; addr < params->size; addr += SZ_128M) {
+ ret = spansion_read_any_reg(nor, addr + SPINOR_REG_ADDR_CFR3V,
+ 0, &cfr3v);
+ if (ret)
+ return ret;
+
+ if (!(cfr3v & CFR3V_PGMBUF)) {
+ params->page_size = 256;
+ return 0;
+ }
+ }
+ params->page_size = 512;
+
+ return 0;
+}
+
+static void s25hx_t_post_sfdp_fixup(struct spi_nor *nor,
+ struct spi_nor_flash_parameter *params)
+{
+ /* READ_FAST_4B (0Ch) requires mode cycles*/
+ params->reads[SNOR_CMD_READ_FAST].num_mode_clocks = 8;
+ /* PP_1_1_4 is not supported */
+ params->hwcaps.mask &= ~SNOR_HWCAPS_PP_1_1_4;
+ /* Use volatile register to enable quad */
+ params->quad_enable = s25hx_t_quad_enable;
+}
+
+static struct spi_nor_fixups s25hx_t_fixups = {
+ .default_init = s25hx_t_default_init,
+ .post_bfpt = s25hx_t_post_bfpt_fixup,
+ .post_sfdp = s25hx_t_post_sfdp_fixup,
+};
+
+static int s25fl256l_setup(struct spi_nor *nor, const struct flash_info *info,
+ const struct spi_nor_flash_parameter *params)
+{
+ return -ENOTSUPP; /* Bank Address Register is not supported */
+}
+
+static void s25fl256l_default_init(struct spi_nor *nor)
+{
+ nor->setup = s25fl256l_setup;
+}
+
+static struct spi_nor_fixups s25fl256l_fixups = {
+ .default_init = s25fl256l_default_init,
+};
+#endif
+