#define CONFIG_PM856 1 /* PM856 board specific */
#define CONFIG_PCI
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-#undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_ECC /* only for ECC DDR module */
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-#define CONFIG_MEM_INIT_VALUE 0xDEADBEEF
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
/*
* sysclk for MPC85xx
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+/* DDR Setup */
+#define CONFIG_FSL_DDR1
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#undef CONFIG_DDR_SPD
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_ECC /* only for ECC DDR module */
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE 0x00000000
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
-#if defined(CONFIG_SPD_EEPROM)
- /*
- * Determine DDR configuration from I2C interface.
- */
- #define SPD_EEPROM_ADDRESS 0x58 /* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
-#else
- /*
- * Manually set up DDR parameters
- */
- #define CFG_SDRAM_SIZE 256 /* DDR is 256 MB */
- #define CFG_DDR_CS0_BNDS 0x0000000f /* 0-256MB */
- #define CFG_DDR_CS0_CONFIG 0x80000102
- #define CFG_DDR_TIMING_1 0x47444321
- #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
- #define CFG_DDR_CONTROL 0xc2008000 /* unbuffered,no DYN_PWR */
- #define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
- #define CFG_DDR_INTERVAL 0x045b0100 /* autocharge,no open page */
-#endif
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS 0x58 /* CTLR 0 DIMM 0 */
+/* Manually set up DDR parameters */
+#define CFG_SDRAM_SIZE 256 /* DDR is 256 MB */
+#define CFG_DDR_CS0_BNDS 0x0000000f /* 0-256MB */
+#define CFG_DDR_CS0_CONFIG 0x80000102
+#define CFG_DDR_TIMING_1 0x47444321
+#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
+#define CFG_DDR_CONTROL 0xc2008000 /* unbuffered,no DYN_PWR */
+#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
+#define CFG_DDR_INTERVAL 0x045b0100 /* autocharge,no open page */
/*
* SDRAM on the Local Bus
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#undef CFG_RAMBOOT
#endif
-#define CFG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_LOCK 1
#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_ON_SCC /* define if console on SCC */
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xe0000000
#define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#if defined(CONFIG_TSEC_ENET)
#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
+#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_MII 1 /* MII PHY management */
* Environment
*/
#ifndef CFG_RAMBOOT
- #define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x80000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
- #define CFG_ENV_SIZE 0x2000
+ #define CONFIG_ENV_IS_IN_FLASH 1
+ #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x80000)
+ #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+ #define CONFIG_ENV_SIZE 0x2000
#else
#define CFG_NO_FLASH 1 /* Flash is not usable now */
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
- #define CFG_ENV_SIZE 0x2000
+ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CONFIG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
-#endif
-
/*
* Internal Definitions
*