.. SPDX-License-Identifier: GPL-2.0+ .. Copyright (C) 2020 Sean Anderson Maix Bit ======== Several of the Sipeed Maix series of boards cotain the Kendryte K210 processor, a 64-bit RISC-V CPU. This processor contains several peripherals to accelerate neural network processing and other "ai" tasks. This includes a "KPU" neural network processor, an audio processor supporting beamforming reception, and a digital video port supporting capture and output at VGA resolution. Other peripherals include 8M of SRAM (accessible with and without caching); remappable pins, including 40 GPIOs; AES, FFT, and SHA256 accelerators; a DMA controller; and I2C, I2S, and SPI controllers. Maix peripherals vary, but include spi flash; on-board usb-serial bridges; ports for cameras, displays, and sd cards; and ESP32 chips. Currently, only the Sipeed Maix Bit V2.0 (bitm) is supported, but the boards are fairly similar. Documentation for Maix boards is available from `Sipeed's website `_. Documentation for the Kendryte K210 is available from `Kendryte's website `_. However, hardware details are rather lacking, so most technical reference has been taken from the `standalone sdk `_. Build and boot steps -------------------- To build u-boot, run .. code-block:: none make sipeed_maix_bitm_defconfig make CROSS_COMPILE= To flash u-boot to a maix bit, run .. code-block:: none kflash -tp /dev/ -B bit_mic u-boot-dtb.bin Boot output should look like the following: .. code-block:: none U-Boot 2020.04-rc2-00087-g2221cc09c1-dirty (Feb 28 2020 - 13:53:09 -0500) DRAM: 8 MiB In: serial@38000000 Out: serial@38000000 Err: serial@38000000 => Loading Images ^^^^^^^^^^^^^^ To load a kernel, transfer it over serial. .. code-block:: none => loady 80000000 1500000 ## Switch baudrate to 1500000 bps and press ENTER ... *** baud: 1500000 *** baud: 1500000 *** ## Ready for binary (ymodem) download to 0x80000000 at 1500000 bps... C *** file: loader.bin $ sz -vv loader.bin Sending: loader.bin Bytes Sent:2478208 BPS:72937 Sending: Ymodem sectors/kbytes sent: 0/ 0k Transfer complete *** exit status: 0 *** ## Total Size = 0x0025d052 = 2478162 Bytes ## Switch baudrate to 115200 bps and press ESC ... *** baud: 115200 *** baud: 115200 *** => Running Programs ^^^^^^^^^^^^^^^^ Binaries """""""" To run a bare binary, use the ``go`` command: .. code-block:: none => loady ## Ready for binary (ymodem) download to 0x80000000 at 115200 bps... C *** file: ./examples/standalone/hello_world.bin $ sz -vv ./examples/standalone/hello_world.bin Sending: hello_world.bin Bytes Sent: 4864 BPS:649 Sending: Ymodem sectors/kbytes sent: 0/ 0k Transfer complete *** exit status: 0 *** (CAN) packets, 5 retries ## Total Size = 0x000012f8 = 4856 Bytes => go 80000000 ## Starting application at 0x80000000 ... Example expects ABI version 9 Actual U-Boot ABI version 9 Hello World argc = 1 argv[0] = "80000000" argv[1] = "" Hit any key to exit ... Legacy Images """"""""""""" To run legacy images, use the ``bootm`` command: .. code-block:: none $ tools/mkimage -A riscv -O u-boot -T standalone -C none -a 80000000 -e 80000000 -d examples/standalone/hello_world.bin hello_world.img Image Name: Created: Thu Mar 5 12:04:10 2020 Image Type: RISC-V U-Boot Standalone Program (uncompressed) Data Size: 4856 Bytes = 4.74 KiB = 0.00 MiB Load Address: 80000000 Entry Point: 80000000 $ picocom -b 115200 /dev/ttyUSB0i => loady ## Ready for binary (ymodem) download to 0x80000000 at 115200 bps... C *** file: hello_world.img $ sz -vv hello_world.img Sending: hello_world.img Bytes Sent: 4992 BPS:665 Sending: Ymodem sectors/kbytes sent: 0/ 0k Transfer complete *** exit status: 0 *** CAN) packets, 3 retries ## Total Size = 0x00001338 = 4920 Bytes => bootm ## Booting kernel from Legacy Image at 80000000 ... Image Name: Image Type: RISC-V U-Boot Standalone Program (uncompressed) Data Size: 4856 Bytes = 4.7 KiB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK Loading Standalone Program Example expects ABI version 9 Actual U-Boot ABI version 9 Hello World argc = 0 argv[0] = "" Hit any key to exit ... Over- and Under-clocking ------------------------ To change the clock speed of the K210, you will need to enable ``CONFIG_CLK_K210_SET_RATE`` and edit the board's device tree. To do this, add a section to ``arch/riscv/arch/riscv/dts/k210-maix-bit.dts`` like the following: .. code-block:: none &sysclk { assigned-clocks = <&sysclk K210_CLK_PLL0>; assigned-clock-rates = <800000000>; }; There are three PLLs on the K210: PLL0 is the parent of most of the components, including the CPU and RAM. PLL1 is the parent of the neural network coprocessor. PLL2 is the parent of the sound processing devices. Note that child clocks of PLL0 and PLL2 run at *half* the speed of the PLLs. For example, if PLL0 is running at 800 MHz, then the CPU will run at 400 MHz. This is the example given above. The CPU can be overclocked to around 600 MHz, and underclocked to 26 MHz. It is possible to set PLL2's parent to PLL0. The plls are more accurate when converting between similar frequencies. This makes it easier to get an accurate frequency for I2S. As an example, consider sampling an I2S device at 44.1 kHz. On this device, the I2S serial clock runs at 64 times the sample rate. Therefore, we would like to run PLL2 at an even multiple of 2.8224 MHz. If PLL2's parent is IN0, we could use a frequency of 390 MHz (the same as the CPU's default speed). Dividing by 138 yields a serial clock of about 2.8261 MHz. This results in a sample rate of 44.158 kHz---around 50 Hz or .1% too fast. If, instead, we set PLL2's parent to PLL1 running at 390 MHz, and request a rate of 2.8224 * 136 = 383.8464 MHz, the achieved rate is 383.90625 MHz. Dividing by 136 yields a serial clock of about 2.8228 MHz. This results in a sample rate of 44.107 kHz---just 7 Hz or .02% too fast. This configuration is shown in the following example: .. code-block:: none &sysclk { assigned-clocks = <&sysclk K210_CLK_PLL1>, <&sysclk K210_CLK_PLL2>; assigned-clock-parents = <0>, <&sysclk K210_CLK_PLL1>; assigned-clock-rates = <390000000>, <383846400>; }; There are a couple of quirks to the PLLs. First, there are more frequency ratios just above and below 1.0, but there is a small gap around 1.0. To be explicit, if the input frequency is 100 MHz, it would be impossible to have an output of 99 or 101 MHz. In addition, there is a maximum frequency for the internal VCO, so higher input/output frequencies will be less accurate than lower ones. Technical Details ----------------- Boot Sequence ^^^^^^^^^^^^^ 1. ``RESET`` pin is deasserted. 2. Both harts begin executing at ``0x00001000``. 3. Both harts jump to firmware at ``0x88000000``. 4. One hart is chosen as a boot hart. 5. Firmware reads value of pin ``IO_16`` (ISP). * If the pin is low, enter ISP mode. This mode allows loading data to ram, writing it to flash, and booting from specific addresses. * If the pin is high, continue boot. 6. Firmware reads the next stage from flash (SPI3) to address ``0x80000000``. * If byte 0 is 1, the next stage is decrypted using the built-in AES accelerator and the one-time programmable, 128-bit AES key. * Bytes 1 to 4 hold the length of the next stage. * The SHA-256 sum of the next stage is automatically calculated, and verified against the 32 bytes following the next stage. 7. The boot hart sends an IPI to the other hart telling it to jump to the next stage. 8. The boot hart jumps to ``0x80000000``. Memory Map ^^^^^^^^^^ ========== ========= =========== Address Size Description ========== ========= =========== 0x00000000 0x1000 debug 0x00001000 0x1000 rom 0x02000000 0xC000 clint 0x0C000000 0x4000000 plic 0x38000000 0x1000 uarths 0x38001000 0x1000 gpiohs 0x40000000 0x400000 sram0 (non-cached) 0x40400000 0x200000 sram1 (non-cached) 0x40600000 0x200000 airam (non-cached) 0x40800000 0xC00000 kpu 0x42000000 0x400000 fft 0x50000000 0x1000 dmac 0x50200000 0x200000 apb0 0x50200000 0x80 gpio 0x50210000 0x100 uart0 0x50220000 0x100 uart1 0x50230000 0x100 uart2 0x50240000 0x100 spi slave 0x50250000 0x200 i2s0 0x50250200 0x200 apu 0x50260000 0x200 i2s1 0x50270000 0x200 i2s2 0x50280000 0x100 i2c0 0x50290000 0x100 i2c1 0x502A0000 0x100 i2c2 0x502B0000 0x100 fpioa 0x502C0000 0x100 sha256 0x502D0000 0x100 timer0 0x502E0000 0x100 timer1 0x502F0000 0x100 timer2 0x50400000 0x200000 apb1 0x50400000 0x100 wdt0 0x50410000 0x100 wdt1 0x50420000 0x100 otp control 0x50430000 0x100 dvp 0x50440000 0x100 sysctl 0x50450000 0x100 aes 0x50460000 0x100 rtc 0x52000000 0x4000000 apb2 0x52000000 0x100 spi0 0x53000000 0x100 spi1 0x54000000 0x200 spi3 0x80000000 0x400000 sram0 (cached) 0x80400000 0x200000 sram1 (cached) 0x80600000 0x200000 airam (cached) 0x88000000 0x20000 otp 0x88000000 0xC200 firmware 0x8801C000 0x1000 riscv priv spec 1.9 config 0x8801D000 0x2000 flattened device tree (contains only addresses and interrupts) 0x8801f000 0x1000 credits ========== ========= ===========