FU540-C000 RISC-V SoC ===================== The FU540-C000 is the world’s first 4+1 64-bit RISC‑V SoC from SiFive. The HiFive Unleashed development platform is based on FU540-C000 and capable of running Linux. Mainline support ================ The support for following drivers are already enabled: 1. SiFive UART Driver. 2. SiFive PRCI Driver for clock. 3. Cadence MACB ethernet driver for networking support. TODO: 1. U-Boot expects the serial console device entry to be present under /chosen DT node. Example: chosen { stdout-path = "/soc/serial@10010000:115200"; }; Without a serial console U-Boot will panic. Building ======== 1. Add the RISC-V toolchain to your PATH. 2. Setup ARCH & cross compilation enviornment variable. a. export ARCH=riscv b. export CROSS_COMPILE= 3. make sifive_fu540_defconfig 4. make Flashing ======== The current U-Boot port is supported in S-mode only and loaded directly into DRAM. A prior stage (M-mode) firmware/bootloader (e.g OpenSBI) is required to boot the u-boot.bin in S-mode and provide M-mode runtime services. Currently, the u-boot.bin is used as a payload of the OpenSBI FW_PAYLOAD firmware. We need to compile OpenSBI with below command: make PLATFORM=sifive/fu540 FW_PAYLOAD_PATH= FW_PAYLOAD_FDT_PATH= (Note: Prefer hifive-unleashed-a00.dtb from Linux-5.3 or higher) (Note: Linux-5.2 is also fine but it does not have ethernet DT node) More detailed description of steps required to build FW_PAYLOAD firmware is beyond the scope of this document. Please refer OpenSBI documenation. (Note: OpenSBI git repo is at https://github.com/riscv/opensbi.git) Once the prior stage firmware/bootloader binary is generated, it should be copied to the first partition of the sdcard. sudo dd if= of=/dev/disk2s1 bs=1024 Booting ======= Once you plugin the sdcard and power up, you should see the U-Boot prompt. Sample boot log from HiFive Unleashed board =========================================== U-Boot 2019.07-rc4-00013-g1837f893b0 (Jun 20 2019 - 11:08:48 +0530) CPU: rv64imafdc Model: SiFive HiFive Unleashed A00 DRAM: 8 GiB In: serial@10010000 Out: serial@10010000 Err: serial@10010000 Net: eth0: ethernet@10090000 Hit any key to stop autoboot: 0 => version U-Boot 2019.07-rc4-00013-g1837f893b0 (Jun 20 2019 - 11:08:48 +0530) riscv64-linux-gcc.br_real (Buildroot 2018.11-rc2-00003-ga0787e9) 8.2.0 GNU ld (GNU Binutils) 2.31.1 => =============================================================================== Now you can configure your networking, tftp server and use tftp boot method to load uImage. ========================================================================== => setenv ipaddr 10.206.5.241 => setenv netmask 255.255.252.0 => setenv serverip 10.206.4.143 => setenv gateway 10.206.4.1 => tftpboot ${kernel_addr_r} /sifive/fu540/uImage ethernet@10090000: PHY present at 0 ethernet@10090000: Starting autonegotiation... ethernet@10090000: Autonegotiation complete ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x7c00) Using ethernet@10090000 device TFTP from server 10.206.4.143; our IP address is 10.206.5.241 Filename '/sifive/fu540/uImage'. Load address: 0x80600000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################## 1.5 MiB/s done Bytes transferred = 9162364 (8bce7c hex) => tftpboot ${ramdisk_addr_r} /sifive/fu540/uRamdisk ethernet@10090000: PHY present at 0 ethernet@10090000: Starting autonegotiation... ethernet@10090000: Autonegotiation complete ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x7c00) Using ethernet@10090000 device TFTP from server 10.206.4.143; our IP address is 10.206.5.241 Filename '/sifive/fu540/uRamdisk'. Load address: 0x82500000 Loading: ################################################################# ################################################################# ################################## 448.2 KiB/s done Bytes transferred = 2398272 (249840 hex) => setenv bootargs "root=/dev/ram rw console=ttySIF0 earlycon=sbi" => bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdtcontroladdr} ## Booting kernel from Legacy Image at 80600000 ... Image Name: Linux Image Type: RISC-V Linux Kernel Image (uncompressed) Data Size: 9162300 Bytes = 8.7 MiB Load Address: 80200000 Entry Point: 80200000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 82500000 ... Image Name: Linux RootFS Image Type: RISC-V Linux RAMDisk Image (uncompressed) Data Size: 2398208 Bytes = 2.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at ff795730 Booting using the fdt blob at 0xff795730 Loading Kernel Image ... OK Using Device Tree in place at 00000000ff795730, end 00000000ff799dac Starting kernel ... [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000 [ 0.000000] Linux version 5.2.0-rc1-00003-gb9543e66e700 (anup@anup-lab-machine) (gcc version 8.2.0 (Buildroot 2018.11-rc2-00003-ga0787e9)) #1 SMP Thu Jun 20 11:41:26 IST 2019 [ 0.000000] earlycon: sbi0 at I/O port 0x0 (options '') [ 0.000000] printk: bootconsole [sbi0] enabled [ 0.000000] Initial ramdisk at: 0x(____ptrval____) (2398208 bytes) [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000027fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080200000-0x000000027fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000027fffffff] [ 0.000000] software IO TLB: mapped [mem 0xfb795000-0xff795000] (64MB) [ 0.000000] CPU with hartid=0 is not available [ 0.000000] CPU with hartid=0 is not available [ 0.000000] elf_hwcap is 0x112d [ 0.000000] percpu: Embedded 17 pages/cpu s29592 r8192 d31848 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975 [ 0.000000] Kernel command line: root=/dev/ram rw console=ttySIF0 earlycon=sbi [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Sorting __ex_table... [ 0.000000] Memory: 8182056K/8386560K available (5753K kernel code, 357K rwdata, 1804K rodata, 204K init, 808K bss, 204504K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0 [ 0.000000] plic: mapped 53 interrupts with 4 handlers for 9 contexts. [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [2] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns [ 0.000007] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns [ 0.008553] Console: colour dummy device 80x25 [ 0.012990] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=4000) [ 0.023103] pid_max: default: 32768 minimum: 301 [ 0.028269] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.035068] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.042770] *** VALIDATE proc *** [ 0.045610] *** VALIDATE cgroup1 *** [ 0.049157] *** VALIDATE cgroup2 *** [ 0.053743] rcu: Hierarchical SRCU implementation. [ 0.058297] smp: Bringing up secondary CPUs ... [ 0.064134] smp: Brought up 1 node, 4 CPUs [ 0.069114] devtmpfs: initialized [ 0.073281] random: get_random_u32 called from bucket_table_alloc.isra.10+0x4e/0x160 with crng_init=0 [ 0.082157] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.091634] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.098480] NET: Registered protocol family 16 [ 0.114101] vgaarb: loaded [ 0.116397] SCSI subsystem initialized [ 0.120358] usbcore: registered new interface driver usbfs [ 0.125541] usbcore: registered new interface driver hub [ 0.130936] usbcore: registered new device driver usb [ 0.136618] clocksource: Switched to clocksource riscv_clocksource [ 0.148108] NET: Registered protocol family 2 [ 0.152358] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes) [ 0.159928] TCP established hash table entries: 65536 (order: 7, 524288 bytes) [ 0.169027] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.178360] TCP: Hash tables configured (established 65536 bind 65536) [ 0.184653] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.190819] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.197618] NET: Registered protocol family 1 [ 0.201892] RPC: Registered named UNIX socket transport module. [ 0.207395] RPC: Registered udp transport module. [ 0.212159] RPC: Registered tcp transport module. [ 0.216940] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.223445] PCI: CLS 0 bytes, default 64 [ 0.227726] Unpacking initramfs... [ 0.260556] Freeing initrd memory: 2336K [ 0.264652] workingset: timestamp_bits=62 max_order=21 bucket_order=0 [ 0.278452] NFS: Registering the id_resolver key type [ 0.282841] Key type id_resolver registered [ 0.287067] Key type id_legacy registered [ 0.291155] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.298299] NET: Registered protocol family 38 [ 0.302470] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.309906] io scheduler mq-deadline registered [ 0.314501] io scheduler kyber registered [ 0.354134] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.360725] 10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 4, base_baud = 0) is a SiFive UART v0 [ 0.369191] printk: console [ttySIF0] enabled [ 0.369191] printk: console [ttySIF0] enabled [ 0.377938] printk: bootconsole [sbi0] disabled [ 0.377938] printk: bootconsole [sbi0] disabled [ 0.387298] 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 1, base_baud = 0) is a SiFive UART v0 [ 0.396411] [drm] radeon kernel modesetting enabled. [ 0.409818] loop: module loaded [ 0.412606] libphy: Fixed MDIO Bus: probed [ 0.416870] macb 10090000.ethernet: Registered clk switch 'sifive-gemgxl-mgmt' [ 0.423570] macb: GEM doesn't support hardware ptp. [ 0.428469] libphy: MACB_mii_bus: probed [ 1.053009] Microsemi VSC8541 SyncE 10090000.ethernet-ffffffff:00: attached PHY driver [Microsemi VSC8541 SyncE] (mii_bus:phy_addr=10090000.ethernet-ffffffff:00, irq=POLL) [ 1.067548] macb 10090000.ethernet eth0: Cadence GEM rev 0x10070109 at 0x10090000 irq 7 (70:b3:d5:92:f2:f3) [ 1.077330] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.083069] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.089061] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.095485] ehci-pci: EHCI PCI platform driver [ 1.099947] ehci-platform: EHCI generic platform driver [ 1.105196] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.111286] ohci-pci: OHCI PCI platform driver [ 1.115742] ohci-platform: OHCI generic platform driver [ 1.121142] usbcore: registered new interface driver uas [ 1.126269] usbcore: registered new interface driver usb-storage [ 1.132331] mousedev: PS/2 mouse device common for all mice [ 1.137978] usbcore: registered new interface driver usbhid [ 1.143325] usbhid: USB HID core driver [ 1.148022] NET: Registered protocol family 10 [ 1.152609] Segment Routing with IPv6 [ 1.155571] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.161927] NET: Registered protocol family 17 [ 1.165907] Key type dns_resolver registered [ 1.171694] Freeing unused kernel memory: 204K [ 1.175375] This architecture does not have kernel memory protection. [ 1.181792] Run /init as init process _ _ | ||_| | | _ ____ _ _ _ _ | || | _ \| | | |\ \/ / | || | | | | |_| |/ \ |_||_|_| |_|\____|\_/\_/ Busybox Rootfs Please press Enter to activate this console. / #