4 * Copyright (c) 2000 - 2011 Samsung Electronics Co., Ltd. All rights reserved.
6 * Contact: Jeongmo Yang <jm80.yang@samsung.com>
8 * Licensed under the Apache License, Version 2.0 (the "License");
9 * you may not use this file except in compliance with the License.
10 * You may obtain a copy of the License at
12 * http://www.apache.org/licenses/LICENSE-2.0
14 * Unless required by applicable law or agreed to in writing, software
15 * distributed under the License is distributed on an "AS IS" BASIS,
16 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
17 * See the License for the specific language governing permissions and
18 * limitations under the License.
27 This part describes the APIs with repect to Multimedia Camcorder.
28 Camcorder is for recording audio and video from audio and video input devices, capturing
29 still image from video input device, and audio recording from audio input
33 Camcorder can be reached by calling functions as shown in the following
34 figure, "The State of Camcorder".
37 @image html camcorder_state.png "The State of Camcorder" width=12cm
38 @image latex camcorder_state.png "The State of Camcorder" width=12cm
41 Between each states there is intermediate state, and in this state,
42 any function call which change the camcorder state will be failed.
45 Recording state and paused state exists when the mode of camcorder is
46 video-capture or audio-capture mode. In case of image-capture mode, CAPTURING state will
59 <td>mm_camcorder_create()</td>
65 <td>mm_camcorder_destroy()</td>
71 <td>mm_camcorder_realize()</td>
77 <td>mm_camcorder_unrealize()</td>
83 <td>mm_camcorder_start()</td>
89 <td>mm_camcorder_stop()</td>
95 <td>mm_camcorder_capture_start()</td>
101 <td>mm_camcorder_capture_stop()</td>
107 <td>mm_camcorder_record()</td>
108 <td>PREPARED/PAUSED</td>
113 <td>mm_camcorder_pause()</td>
119 <td>mm_camcorder_commit()</td>
120 <td>RECORDING/PAUSED</td>
125 <td>mm_camcorder_cancel()</td>
126 <td>RECORDING/PAUSED</td>
131 <td>mm_camcorder_set_message_callback()</td>
137 <td>mm_camcorder_set_video_stream_callback()</td>
143 <td>mm_camcorder_set_video_capture_callback()</td>
149 <td>mm_camcorder_get_state()</td>
155 <td>mm_camcorder_get_attributes()</td>
161 <td>mm_camcorder_set_attributes()</td>
167 <td>mm_camcorder_get_attribute_info()</td>
173 <td>mm_camcorder_init_focusing()</td>
179 <td>mm_camcorder_start_focusing()</td>
185 <td>mm_camcorder_stop_focusing()</td>
195 Attribute system is an interface to operate camcorder. Depending on each attribute, camcorder behaves differently.
196 Attribute system provides get/set functions. Setting proper attributes, a user can control camcorder as he want. (mm_camcorder_set_attributes())
197 Also, a user can comprehend current status of the camcorder, calling getter function(mm_camcorder_get_attributes()).
198 Beware, arguments of mm_camcorder_set_attributes() and mm_camcorder_get_attributes() should be finished with 'NULL'.
199 This is a rule for the variable argument.
201 Besides its value, each Attribute also has 'type' and 'validity type'. 'type' describes variable type that the attribute can get.
202 If you input a value that has wrong type, camcorder will not work properly or be crashed. 'validity' describes array or
203 range of values that are able to set to the attribute. 'validity type' defines type of the 'validity'.
205 A user can retrieve these values using mm_camcorder_get_attribute_info().
206 Following tables have 'Attribute name', 'Attribute macro', 'Type', and 'Validity type'. You can refer '#MMCamAttrsType' and '#MMCamAttrsValidType'
207 for discerning 'Type' and 'Validity type'.
211 Following are the attributes which should be set before initialization (#mm_camcorder_realize):
217 <td><center><b>Attribute</b></center></td>
218 <td><center><b>Description</b></center></td>
222 <td>Mode of camcorder ( still/video/audio )</td>
225 <td>#MMCAM_AUDIO_DEVICE</td>
226 <td>Audio device ID for capturing audio stream</td>
229 <td>#MMCAM_CAMERA_DEVICE_COUNT</td>
230 <td>Video device count</td>
233 <td>#MMCAM_AUDIO_ENCODER</td>
234 <td>Audio codec for encoding audio stream</td>
237 <td>#MMCAM_VIDEO_ENCODER</td>
238 <td>Video codec for encoding video stream</td>
241 <td>#MMCAM_IMAGE_ENCODER</td>
242 <td>Image codec for capturing still-image</td>
245 <td>#MMCAM_FILE_FORMAT</td>
246 <td>File format for recording media stream</td>
249 <td>#MMCAM_AUDIO_SAMPLERATE</td>
250 <td>Sampling rate of audio stream ( This is an integer field )</td>
253 <td>#MMCAM_AUDIO_FORMAT</td>
254 <td>Audio format of each sample</td>
257 <td>#MMCAM_AUDIO_CHANNEL</td>
258 <td>Channels of each sample ( This is an integer field )</td>
261 <td>#MMCAM_AUDIO_INPUT_ROUTE(deprecated)</td>
262 <td>Set audio input route</td>
265 <td>#MMCAM_CAMERA_FORMAT</td>
266 <td>Format of video stream. This is an integer field</td>
269 <td>#MMCAM_CAMERA_FPS</td>
270 <td>Frames per second ( This is an integer field )</td>
273 <td>#MMCAM_CAMERA_WIDTH</td>
274 <td>Width of input video stream</td>
277 <td>#MMCAM_CAMERA_HEIGHT</td>
278 <td>Height of input video stream</td>
281 <td>#MMCAM_CAMERA_FPS_AUTO</td>
282 <td>FPS Auto. When you set true to this attribute, FPS will vary depending on the amount of the light.</td>
285 <td>#MMCAM_DISPLAY_HANDLE</td>
286 <td>Pointer of display buffer or ID of xwindow</td>
289 <td>#MMCAM_DISPLAY_DEVICE</td>
290 <td>Device of display</td>
293 <td>#MMCAM_DISPLAY_SURFACE</td>
294 <td>Surface of display</td>
297 <td>#MMCAM_DISPLAY_SOURCE_X</td>
298 <td>X position of source rectangle. When you want to crop the source, you can set the area with this value.</td>
301 <td>#MMCAM_DISPLAY_SOURCE_Y</td>
302 <td>Y position of source rectangle. When you want to crop the source, you can set the area with this value.</td>
305 <td>#MMCAM_DISPLAY_SOURCE_WIDTH</td>
306 <td>Width of source rectangle. When you want to crop the source, you can set the area with this value.</td>
309 <td>#MMCAM_DISPLAY_SOURCE_HEIGHT</td>
310 <td>Height of source rectangle. When you want to crop the source, you can set the area with this value.</td>
313 <td>#MMCAM_DISPLAY_ROTATION</td>
314 <td>Rotation of display</td>
317 <td>#MMCAM_DISPLAY_VISIBLE</td>
318 <td>Visible of display</td>
321 <td>#MMCAM_DISPLAY_SCALE</td>
322 <td>A scale of displayed image</td>
325 <td>#MMCAM_DISPLAY_GEOMETRY_METHOD</td>
326 <td>A method that describes a form of geometry for display</td>
332 Following are the attributes which should be set before recording (mm_camcorder_record()):
338 <td><center><b>Attribute</b></center></td>
339 <td><center><b>Description</b></center></td>
342 <td>#MMCAM_AUDIO_ENCODER_BITRATE</td>
343 <td>Bitrate of Audio Encoder</td>
346 <td>#MMCAM_VIDEO_ENCODER_BITRATE</td>
347 <td>Bitrate of Video Encoder</td>
350 <td>#MMCAM_TARGET_FILENAME</td>
351 <td>Target filename. Only used in Audio/Video recording. This is not used for capturing.</td>
354 <td>#MMCAM_TARGET_MAX_SIZE</td>
355 <td>Maximum size of recording file(Kbyte). If the size of file reaches this value.</td>
358 <td>#MMCAM_TARGET_TIME_LIMIT</td>
359 <td>Time limit of recording file. If the elapsed time of recording reaches this value.</td>
365 Following are the attributes which should be set before capturing (mm_camcorder_capture_start()):
371 <td><center><b>Attribute</b></center></td>
372 <td><center><b>Description</b></center></td>
375 <td>#MMCAM_IMAGE_ENCODER_QUALITY</td>
376 <td>Encoding quality of Image codec</td>
379 <td>#MMCAM_CAPTURE_FORMAT</td>
380 <td>Pixel format that you want to capture</td>
383 <td>#MMCAM_CAPTURE_WIDTH</td>
384 <td>Width of the image that you want to capture</td>
387 <td>#MMCAM_CAPTURE_HEIGHT</td>
388 <td>Height of the image that you want to capture</td>
391 <td>#MMCAM_CAPTURE_COUNT</td>
392 <td>Total count of capturing</td>
395 <td>#MMCAM_CAPTURE_INTERVAL</td>
396 <td>Interval between each capturing on Multishot ( MMCAM_CAPTURE_COUNT > 1 )</td>
402 Following are the attributes which can be set anytime:
408 <td><center><b>Attribute</b></center></td>
409 <td><center><b>Description</b></center></td>
412 <td>#MMCAM_AUDIO_VOLUME</td>
413 <td>Input volume of audio source ( double value )</td>
416 <td>#MMCAM_CAMERA_DIGITAL_ZOOM</td>
417 <td>Digital zoom level</td>
420 <td>#MMCAM_CAMERA_OPTICAL_ZOOM</td>
421 <td>Optical zoom level</td>
424 <td>#MMCAM_CAMERA_FOCUS_MODE</td>
428 <td>#MMCAM_CAMERA_AF_SCAN_RANGE</td>
429 <td>AF Scan range</td>
432 <td>#MMCAM_CAMERA_AF_TOUCH_X</td>
433 <td>X coordinate of touching position</td>
436 <td>#MMCAM_CAMERA_AF_TOUCH_Y</td>
437 <td>Y coordinate of touching position</td>
440 <td>#MMCAM_CAMERA_AF_TOUCH_WIDTH</td>
441 <td>Width of touching area</td>
444 <td>#MMCAM_CAMERA_AF_TOUCH_HEIGHT</td>
445 <td>Height of touching area</td>
448 <td>#MMCAM_CAMERA_EXPOSURE_MODE</td>
449 <td>Exposure mode</td>
452 <td>#MMCAM_CAMERA_EXPOSURE_VALUE</td>
453 <td>Exposure value</td>
456 <td>#MMCAM_CAMERA_F_NUMBER</td>
457 <td>f number of camera</td>
460 <td>#MMCAM_CAMERA_SHUTTER_SPEED</td>
461 <td>Shutter speed</td>
464 <td>#MMCAM_CAMERA_ISO</td>
465 <td>ISO of capturing image</td>
468 <td>#MMCAM_CAMERA_WDR</td>
469 <td>Wide dynamic range</td>
472 <td>#MMCAM_CAMERA_ANTI_HANDSHAKE</td>
473 <td>Anti Handshake</td>
476 <td>#MMCAM_CAMERA_FOCAL_LENGTH</td>
477 <td>Focal length of camera lens</td>
480 <td>#MMCAM_FILTER_BRIGHTNESS</td>
481 <td>Brightness level</td>
484 <td>#MMCAM_FILTER_CONTRAST</td>
485 <td>Contrast level</td>
488 <td>#MMCAM_FILTER_WB</td>
489 <td>White balance</td>
492 <td>#MMCAM_FILTER_COLOR_TONE</td>
493 <td>Color tone (Color effect)</td>
496 <td>#MMCAM_FILTER_SCENE_MODE</td>
497 <td>Scene mode (Program mode)</td>
500 <td>#MMCAM_FILTER_SATURATION</td>
501 <td>Saturation level</td>
504 <td>#MMCAM_FILTER_HUE</td>
508 <td>#MMCAM_FILTER_SHARPNESS</td>
509 <td>Sharpness level</td>
512 <td>#MMCAM_CAPTURE_BREAK_CONTINUOUS_SHOT</td>
513 <td>Set this as true when you want to stop multishot immediately</td>
516 <td>#MMCAM_DISPLAY_RECT_X</td>
517 <td>X position of display rectangle (This is only available when MMCAM_DISPLAY_GEOMETRY_METHOD is MM_CAMCORDER_CUSTOM_ROI)</td>
520 <td>#MMCAM_DISPLAY_RECT_Y</td>
521 <td>Y position of display rectangle (This is only available when MMCAM_DISPLAY_GEOMETRY_METHOD is MM_CAMCORDER_CUSTOM_ROI)</td>
524 <td>#MMCAM_DISPLAY_RECT_WIDTH</td>
525 <td>Width of display rectangle (This is only available when MMCAM_DISPLAY_GEOMETRY_METHOD is MM_CAMCORDER_CUSTOM_ROI)</td>
528 <td>#MMCAM_DISPLAY_RECT_HEIGHT</td>
529 <td>Height of display rectangle (This is only available when MMCAM_DISPLAY_GEOMETRY_METHOD is MM_CAMCORDER_CUSTOM_ROI)</td>
532 <td>#MMCAM_TAG_ENABLE</td>
533 <td>Enable to write tags (If this value is FALSE, none of tag information will be written to captured file)</td>
536 <td>#MMCAM_TAG_IMAGE_DESCRIPTION</td>
537 <td>Image description</td>
540 <td>#MMCAM_TAG_ORIENTATION</td>
541 <td>Orientation of captured image</td>
544 <td>#MMCAM_TAG_VIDEO_ORIENTATION</td>
545 <td>Orientation of encoded video</td>
548 <td>#MMCAM_TAG_SOFTWARE</td>
549 <td>software name and version</td>
552 <td>#MMCAM_TAG_LATITUDE</td>
553 <td>Latitude of captured postion (GPS information)</td>
556 <td>#MMCAM_TAG_LONGITUDE</td>
557 <td>Longitude of captured postion (GPS information)</td>
560 <td>#MMCAM_TAG_ALTITUDE</td>
561 <td>Altitude of captured postion (GPS information)</td>
564 <td>#MMCAM_STROBE_CONTROL</td>
565 <td>Strobe control</td>
568 <td>#MMCAM_STROBE_MODE</td>
569 <td>Operation Mode of strobe</td>
572 <td>#MMCAM_DETECT_MODE</td>
573 <td>Detection mode</td>
576 <td>#MMCAM_DETECT_NUMBER</td>
577 <td>Total number of detected object</td>
580 <td>#MMCAM_DETECT_FOCUS_SELECT</td>
581 <td>Select one of detected objects</td>
589 #ifndef __MM_CAMCORDER_H__
590 #define __MM_CAMCORDER_H__
593 /*=======================================================================================
595 ========================================================================================*/
598 #include <mm_types.h>
599 #include <mm_error.h>
600 #include <mm_message.h>
606 /*=======================================================================================
607 | GLOBAL DEFINITIONS AND DECLARATIONS FOR CAMCORDER |
608 ========================================================================================*/
610 /*=======================================================================================
611 | MACRO DEFINITIONS |
612 ========================================================================================*/
614 * Get numerator. Definition for fraction setting, such as MMCAM_CAMERA_SHUTTER_SPEED and MMCAM_CAMERA_EXPOSURE_VALUE.
616 #define MM_CAMCORDER_GET_NUMERATOR(x) ((int)(((int)(x) >> 16) & 0xFFFF))
618 * Get denominator. Definition for fraction setting, such as MMCAM_CAMERA_SHUTTER_SPEED and MMCAM_CAMERA_EXPOSURE_VALUE.
620 #define MM_CAMCORDER_GET_DENOMINATOR(x) ((int)(((int)(x)) & 0xFFFF))
622 * Set fraction value. Definition for fraction setting, such as MMCAM_CAMERA_SHUTTER_SPEED and MMCAM_CAMERA_EXPOSURE_VALUE.
624 #define MM_CAMCORDER_SET_FRACTION(numerator, denominator) ((int)((((int)(numerator)) << 16) | (int)(denominator)))
626 /* Attributes Macros */
628 * Mode of camcorder (still/video/audio).
629 * @see MMCamcorderModeType
631 #define MMCAM_MODE "mode"
634 * Audio device ID for capturing audio stream.
635 * @see MMAudioDeviceType (in mm_types.h)
637 #define MMCAM_AUDIO_DEVICE "audio-device"
640 * Video device count.
642 #define MMCAM_CAMERA_DEVICE_COUNT "camera-device-count"
645 * Facing direction of camera device.
646 * @see MMCamcorderCameraFacingDirection
648 #define MMCAM_CAMERA_FACING_DIRECTION "camera-facing-direction"
651 * Audio codec for encoding audio stream.
652 * @see MMAudioCodecType (in mm_types.h)
654 #define MMCAM_AUDIO_ENCODER "audio-encoder"
657 * Video codec for encoding video stream.
658 * @see MMVideoCodecType (in mm_types.h)
660 #define MMCAM_VIDEO_ENCODER "video-encoder"
663 * Image codec for capturing still-image.
664 * @see MMImageCodecType (in mm_types.h)
666 #define MMCAM_IMAGE_ENCODER "image-encoder"
669 * File format for recording media stream.
670 * @see MMFileFormatType (in mm_types.h)
672 #define MMCAM_FILE_FORMAT "file-format"
675 * Sampling rate of audio stream. This is an integer field.
677 #define MMCAM_AUDIO_SAMPLERATE "audio-samplerate"
680 * Audio format of each sample.
681 * @see MMCamcorderAudioFormat
683 #define MMCAM_AUDIO_FORMAT "audio-format"
686 * Channels of each sample. This is an integer field.
688 #define MMCAM_AUDIO_CHANNEL "audio-channel"
691 * Input volume of audio source. Double value.
693 #define MMCAM_AUDIO_VOLUME "audio-volume"
696 * Disable Audio stream when record.
698 #define MMCAM_AUDIO_DISABLE "audio-disable"
701 * Set audio input route
702 * @remarks Deprecated. This will be removed soon.
703 * @see MMAudioRoutePolicy (in mm_types.h)
705 #define MMCAM_AUDIO_INPUT_ROUTE "audio-input-route"
708 * Format of video stream. This is an integer field
709 * @see MMPixelFormatType (in mm_types.h)
711 #define MMCAM_CAMERA_FORMAT "camera-format"
714 * Slow motion rate when video recording
715 * @remarks Deprecated
717 #define MMCAM_CAMERA_SLOW_MOTION_RATE "camera-slow-motion-rate"
720 * Motion rate when video recording
721 * @remarks This should be bigger than 0(zero).
722 * Default value is 1 and it's for normal video recording.
723 * If the value is smaller than 1, recorded file will be played slower,
724 * otherwise, recorded file will be played faster.
726 #define MMCAM_CAMERA_RECORDING_MOTION_RATE "camera-recording-motion-rate"
729 * Frames per second. This is an integer field
732 #define MMCAM_CAMERA_FPS "camera-fps"
735 * Width of preview stream.
737 #define MMCAM_CAMERA_WIDTH "camera-width"
740 * Height of preview stream.
742 #define MMCAM_CAMERA_HEIGHT "camera-height"
745 * Width of video stream.
747 #define MMCAM_VIDEO_WIDTH "video-width"
750 * Height of video stream.
752 #define MMCAM_VIDEO_HEIGHT "video-height"
755 * Digital zoom level.
757 #define MMCAM_CAMERA_DIGITAL_ZOOM "camera-digital-zoom"
760 * Optical zoom level.
762 #define MMCAM_CAMERA_OPTICAL_ZOOM "camera-optical-zoom"
766 * @see MMCamcorderFocusMode
768 #define MMCAM_CAMERA_FOCUS_MODE "camera-focus-mode"
772 * @see MMCamcorderAutoFocusType
774 #define MMCAM_CAMERA_AF_SCAN_RANGE "camera-af-scan-range"
777 * X coordinate of touching position. Only available when you set '#MM_CAMCORDER_AUTO_FOCUS_TOUCH' to '#MMCAM_CAMERA_AF_SCAN_RANGE'.
778 * @see MMCamcorderAutoFocusType
780 #define MMCAM_CAMERA_AF_TOUCH_X "camera-af-touch-x"
783 * Y coordinate of touching position. Only available when you set '#MM_CAMCORDER_AUTO_FOCUS_TOUCH' to '#MMCAM_CAMERA_AF_SCAN_RANGE'.
784 * @see MMCamcorderAutoFocusType
786 #define MMCAM_CAMERA_AF_TOUCH_Y "camera-af-touch-y"
789 * Width of touching area. Only available when you set '#MM_CAMCORDER_AUTO_FOCUS_TOUCH' to '#MMCAM_CAMERA_AF_SCAN_RANGE'.
790 * @see MMCamcorderAutoFocusType
792 #define MMCAM_CAMERA_AF_TOUCH_WIDTH "camera-af-touch-width"
795 * Height of touching area. Only available when you set '#MM_CAMCORDER_AUTO_FOCUS_TOUCH' to '#MMCAM_CAMERA_AF_SCAN_RANGE'.
796 * @see MMCamcorderAutoFocusType
798 #define MMCAM_CAMERA_AF_TOUCH_HEIGHT "camera-af-touch-height"
802 * @see MMCamcorderAutoExposureType
804 #define MMCAM_CAMERA_EXPOSURE_MODE "camera-exposure-mode"
809 #define MMCAM_CAMERA_EXPOSURE_VALUE "camera-exposure-value"
814 #define MMCAM_CAMERA_F_NUMBER "camera-f-number"
819 #define MMCAM_CAMERA_SHUTTER_SPEED "camera-shutter-speed"
822 * ISO of capturing image
823 * @see MMCamcorderISOType
825 #define MMCAM_CAMERA_ISO "camera-iso"
828 * Wide dynamic range.
829 * @see MMCamcorderWDRMode
831 #define MMCAM_CAMERA_WDR "camera-wdr"
834 * Focal length of camera lens.
836 #define MMCAM_CAMERA_FOCAL_LENGTH "camera-focal-length"
840 * @see MMCamcorderAHSMode
842 #define MMCAM_CAMERA_ANTI_HANDSHAKE "camera-anti-handshake"
845 * Video Stabilization
846 * @see MMCamcorderVideoStabilizationMode
848 #define MMCAM_CAMERA_VIDEO_STABILIZATION "camera-video-stabilization"
851 * FPS Auto. When you set true to this attribute, FPS will vary depending on the amount of the light.
853 #define MMCAM_CAMERA_FPS_AUTO "camera-fps-auto"
856 * Rotation angle of video input stream.
857 * @see MMVideoInputRotationType (in mm_types.h)
859 #define MMCAM_CAMERA_ROTATION "camera-rotation"
862 * HDR(High Dynamic Range) Capture mode
863 * @see MMCamcorderHDRMode
865 #define MMCAM_CAMERA_HDR_CAPTURE "camera-hdr-capture"
868 * Bitrate of Audio Encoder
870 #define MMCAM_AUDIO_ENCODER_BITRATE "audio-encoder-bitrate"
873 * Bitrate of Video Encoder
875 #define MMCAM_VIDEO_ENCODER_BITRATE "video-encoder-bitrate"
878 * Encoding quality of Image codec
880 #define MMCAM_IMAGE_ENCODER_QUALITY "image-encoder-quality"
885 #define MMCAM_FILTER_BRIGHTNESS "filter-brightness"
890 #define MMCAM_FILTER_CONTRAST "filter-contrast"
894 * @see MMCamcorderWhiteBalanceType
896 #define MMCAM_FILTER_WB "filter-wb"
899 * Color tone. (Color effect)
900 * @see MMCamcorderColorToneType
902 #define MMCAM_FILTER_COLOR_TONE "filter-color-tone"
905 * Scene mode (Program mode)
906 * @see MMCamcorderSceneModeType
908 #define MMCAM_FILTER_SCENE_MODE "filter-scene-mode"
913 #define MMCAM_FILTER_SATURATION "filter-saturation"
918 #define MMCAM_FILTER_HUE "filter-hue"
923 #define MMCAM_FILTER_SHARPNESS "filter-sharpness"
926 * Pixel format that you want to capture. If you set MM_PIXEL_FORMAT_ENCODED,
927 * the result will be encoded by image codec specified in #MMCAM_IMAGE_ENCODER.
928 * If not, the result will be raw data.
930 * @see MMPixelFormatType (in mm_types.h)
932 #define MMCAM_CAPTURE_FORMAT "capture-format"
935 * Width of the image that you want to capture
937 #define MMCAM_CAPTURE_WIDTH "capture-width"
940 * Height of the image that you want to capture
943 #define MMCAM_CAPTURE_HEIGHT "capture-height"
946 * Total count of capturing. If you set this, it will caputre multiple time.
948 #define MMCAM_CAPTURE_COUNT "capture-count"
951 * Interval between each capturing on Multishot.
953 #define MMCAM_CAPTURE_INTERVAL "capture-interval"
956 * Set this when you want to stop multishot immediately.
958 #define MMCAM_CAPTURE_BREAK_CONTINUOUS_SHOT "capture-break-cont-shot"
961 * Raw data of captured image which resolution is same as preview.
962 * This is READ-ONLY attribute and only available in capture callback.
963 * This should be used after casted as MMCamcorderCaptureDataType.
965 #define MMCAM_CAPTURED_SCREENNAIL "captured-screennail"
968 * Raw data of EXIF. This is READ-ONLY attribute and only available in capture callback.
970 #define MMCAM_CAPTURED_EXIF_RAW_DATA "captured-exif-raw-data"
973 * Pointer of display buffer or ID of xwindow.
975 #define MMCAM_DISPLAY_HANDLE "display-handle"
979 * @see MMDisplayDeviceType (in mm_types.h)
981 #define MMCAM_DISPLAY_DEVICE "display-device"
984 * Surface of display.
985 * @see MMDisplaySurfaceType (in mm_types.h)
987 #define MMCAM_DISPLAY_SURFACE "display-surface"
991 * @see MMDisplayModeType (in mm_types.h)
993 #define MMCAM_DISPLAY_MODE "display-mode"
996 * X position of display rectangle.
997 * This is only available when #MMCAM_DISPLAY_GEOMETRY_METHOD is MM_CAMCORDER_CUSTOM_ROI.
998 * @see MMCamcorderGeometryMethod
1000 #define MMCAM_DISPLAY_RECT_X "display-rect-x"
1003 * Y position of display rectangle
1004 * This is only available when #MMCAM_DISPLAY_GEOMETRY_METHOD is MM_CAMCORDER_CUSTOM_ROI.
1005 * @see MMCamcorderGeometryMethod
1007 #define MMCAM_DISPLAY_RECT_Y "display-rect-y"
1010 * Width of display rectangle
1011 * This is only available when #MMCAM_DISPLAY_GEOMETRY_METHOD is MM_CAMCORDER_CUSTOM_ROI.
1012 * @see MMCamcorderGeometryMethod
1014 #define MMCAM_DISPLAY_RECT_WIDTH "display-rect-width"
1017 * Height of display rectangle
1018 * This is only available when #MMCAM_DISPLAY_GEOMETRY_METHOD is MM_CAMCORDER_CUSTOM_ROI.
1019 * @see MMCamcorderGeometryMethod
1021 #define MMCAM_DISPLAY_RECT_HEIGHT "display-rect-height"
1024 * X position of source rectangle. When you want to crop the source, you can set the area with this value.
1026 #define MMCAM_DISPLAY_SOURCE_X "display-src-x"
1029 * Y position of source rectangle. When you want to crop the source, you can set the area with this value.
1031 #define MMCAM_DISPLAY_SOURCE_Y "display-src-y"
1034 * Width of source rectangle. When you want to crop the source, you can set the area with this value.
1036 #define MMCAM_DISPLAY_SOURCE_WIDTH "display-src-width"
1039 * Height of source rectangle. When you want to crop the source, you can set the area with this value.
1041 #define MMCAM_DISPLAY_SOURCE_HEIGHT "display-src-height"
1044 * Rotation angle of display.
1045 * @see MMDisplayRotationType (in mm_types.h)
1047 #define MMCAM_DISPLAY_ROTATION "display-rotation"
1051 * @see MMFlipType (in mm_types.h)
1053 #define MMCAM_DISPLAY_FLIP "display-flip"
1056 * Visible of display.
1058 #define MMCAM_DISPLAY_VISIBLE "display-visible"
1061 * A scale of displayed image. Available value is like below.
1062 * @see MMDisplayScaleType (in mm_types.h)
1064 #define MMCAM_DISPLAY_SCALE "display-scale"
1067 * A method that describes a form of geometry for display.
1068 * @see MMCamcorderGeometryMethod
1070 #define MMCAM_DISPLAY_GEOMETRY_METHOD "display-geometry-method"
1073 * A videosink name of evas surface.
1074 * This is READ-ONLY attribute.
1076 #define MMCAM_DISPLAY_EVAS_SURFACE_SINK "display-evas-surface-sink"
1079 * This attribute is only available if value of MMCAM_DISPLAY_EVAS_SURFACE_SINK "evaspixmapsink"
1081 #define MMCAM_DISPLAY_EVAS_DO_SCALING "display-evas-do-scaling"
1084 * Target filename. Only used in Audio/Video recording. This is not used for capturing.
1086 #define MMCAM_TARGET_FILENAME "target-filename"
1089 * Maximum size(Kbyte) of recording file. If the size of file reaches this value,
1090 * camcorder will send 'MM_MESSAGE_CAMCORDER_MAX_SIZE' message.
1092 #define MMCAM_TARGET_MAX_SIZE "target-max-size"
1095 * Time limit(Second) of recording file. If the elapsed time of recording reaches this value,
1096 * camcorder will send 'MM_MESSAGE_CAMCORDER_TIME_LIMIT' message.
1098 #define MMCAM_TARGET_TIME_LIMIT "target-time-limit"
1101 * Enable to write tags. If this value is FALSE, none of tag information will be written to captured file.
1103 #define MMCAM_TAG_ENABLE "tag-enable"
1106 * Image description.
1108 #define MMCAM_TAG_IMAGE_DESCRIPTION "tag-image-description"
1111 * Orientation of captured image
1112 * @see MMCamcorderTagOrientation
1114 #define MMCAM_TAG_ORIENTATION "tag-orientation"
1117 * Orientation of captured video
1118 * @see MMCamcorderTagVideoOrientation
1120 #define MMCAM_TAG_VIDEO_ORIENTATION "tag-video-orientation"
1123 * software name and version
1125 #define MMCAM_TAG_SOFTWARE "tag-software"
1128 * Enable to write tags related to GPS. If this value is TRUE, tags related GPS information will be written to captured file.
1130 #define MMCAM_TAG_GPS_ENABLE "tag-gps-enable"
1133 * Latitude of captured postion. GPS information.
1135 #define MMCAM_TAG_LATITUDE "tag-latitude"
1138 * Longitude of captured postion. GPS information.
1140 #define MMCAM_TAG_LONGITUDE "tag-longitude"
1143 * Altitude of captured postion. GPS information.
1145 #define MMCAM_TAG_ALTITUDE "tag-altitude"
1149 * @see MMCamcorderStrobeControl
1151 #define MMCAM_STROBE_CONTROL "strobe-control"
1154 * Operation Mode of strobe
1155 * @see MMCamcorderStrobeMode
1157 #define MMCAM_STROBE_MODE "strobe-mode"
1161 * @see MMCamcorderDetectMode
1163 #define MMCAM_DETECT_MODE "detect-mode"
1166 * Total number of detected object
1168 #define MMCAM_DETECT_NUMBER "detect-number"
1171 * You can use this attribute to select one of detected objects.
1173 #define MMCAM_DETECT_FOCUS_SELECT "detect-focus-select"
1176 * Recommend preview format for capture
1178 #define MMCAM_RECOMMEND_PREVIEW_FORMAT_FOR_CAPTURE "recommend-preview-format-for-capture"
1181 * Recommend preview format for recording
1183 #define MMCAM_RECOMMEND_PREVIEW_FORMAT_FOR_RECORDING "recommend-preview-format-for-recording"
1186 * Recommend rotation of display
1188 #define MMCAM_RECOMMEND_DISPLAY_ROTATION "recommend-display-rotation"
1191 * Recommend width of camera preview.
1192 * This attribute can be used with #mm_camcorder_get_attribute_info and #MMCamcorderPreviewType.
1193 * @see mm_camcorder_get_attribute_info, MMCamcorderPreviewType
1195 #define MMCAM_RECOMMEND_CAMERA_WIDTH "recommend-camera-width"
1198 * Recommend height of camera preview
1199 * This attribute can be used with #mm_camcorder_get_attribute_info and #MMCamcorderPreviewType.
1200 * @see mm_camcorder_get_attribute_info, MMCamcorderPreviewType
1202 #define MMCAM_RECOMMEND_CAMERA_HEIGHT "recommend-camera-height"
1205 * Enable to play capture sound
1207 #define MMCAM_CAPTURE_SOUND_ENABLE "capture-sound-enable"
1210 * Flip of video input stream.
1211 * @see MMFlipType (in mm_types.h)
1213 #define MMCAM_CAMERA_FLIP "camera-flip"
1216 * Support Zero Shutter Lag capture
1218 #define MMCAM_SUPPORT_ZSL_CAPTURE "support-zsl-capture"
1221 * Support zero copy format
1223 #define MMCAM_SUPPORT_ZERO_COPY_FORMAT "support-zero-copy-format"
1226 * Support media packet callback
1228 #define MMCAM_SUPPORT_MEDIA_PACKET_PREVIEW_CB "support-media-packet-preview-cb"
1231 * Support user buffer for zero copy
1233 #define MMCAM_SUPPORT_USER_BUFFER "support-user-buffer"
1236 * Buffer fd from user
1238 #define MMCAM_USER_BUFFER_FD "user-buffer-fd"
1241 * Enable to write tags for recorded file
1243 #define MMCAM_RECORDER_TAG_ENABLE "recorder-tag-enable"
1246 * Determines the socket stream path
1248 #define MMCAM_DISPLAY_SOCKET_PATH "display-socket-path"
1253 #define MMCAM_CLIENT_PID "client-pid"
1256 * Root directory of application
1258 #define MMCAM_ROOT_DIRECTORY "root-directory"
1261 * Bitrate for encoded preview stream
1263 #define MMCAM_ENCODED_PREVIEW_BITRATE "encoded-preview-bitrate"
1266 * GOP interval for encoded preview stream
1268 #define MMCAM_ENCODED_PREVIEW_GOP_INTERVAL "encoded-preview-gop-interval"
1271 * The distance to move the camera horizontally and physically
1273 #define MMCAM_CAMERA_PAN_MECHA "camera-pan-mecha"
1276 * The distance to move the camera horizontally
1278 #define MMCAM_CAMERA_PAN_ELEC "camera-pan-elec"
1281 * The distance to move the camera vertically and physically
1283 #define MMCAM_CAMERA_TILT_MECHA "camera-tilt-mecha"
1286 * The distance to move the camera vertically
1288 #define MMCAM_CAMERA_TILT_ELEC "camera-tilt-elec"
1291 * The type of PTZ(Pan Tilt Zoom). Mechanical or Electonic PTZ.
1293 #define MMCAM_CAMERA_PTZ_TYPE "camera-ptz-type"
1296 * Stream type and index for sound route
1298 #define MMCAM_SOUND_STREAM_TYPE "sound-stream-type"
1299 #define MMCAM_SOUND_STREAM_INDEX "sound-stream-index"
1302 * The display reuse flag and sink element pointer
1304 #define MMCAM_DISPLAY_REUSE_HINT "display-reuse-hint"
1305 #define MMCAM_DISPLAY_REUSE_ELEMENT "display-reuse-element"
1308 * The GBbus connection from outside
1310 #define MMCAM_GDBUS_CONNECTION "gdbus-connection"
1313 * Replay gain enable
1315 #define MMCAM_AUDIO_REPLAY_GAIN_ENABLE "audio-replay-gain-enable"
1318 * Reference level for replay gain
1320 #define MMCAM_AUDIO_REPLAY_GAIN_REFERENCE_LEVEL "audio-replay-gain-reference-level"
1322 /*=======================================================================================
1323 | ENUM DEFINITIONS |
1324 ========================================================================================*/
1326 * An enumeration for camcorder states.
1329 MM_CAMCORDER_STATE_NONE, /**< Camcorder is not created yet */
1330 MM_CAMCORDER_STATE_NULL, /**< Camcorder is created, but not initialized yet */
1331 MM_CAMCORDER_STATE_READY, /**< Camcorder is ready to capture */
1332 MM_CAMCORDER_STATE_PREPARE, /**< Camcorder is prepared to capture (Preview) */
1333 MM_CAMCORDER_STATE_CAPTURING, /**< Camcorder is now capturing still images */
1334 MM_CAMCORDER_STATE_RECORDING, /**< Camcorder is now recording */
1335 MM_CAMCORDER_STATE_PAUSED, /**< Camcorder is paused while recording */
1336 MM_CAMCORDER_STATE_NUM, /**< Number of camcorder states */
1337 } MMCamcorderStateType;
1340 * An enumeration for camcorder mode.
1343 MM_CAMCORDER_MODE_VIDEO_CAPTURE = 0, /**< Video recording and Image capture mode */
1344 MM_CAMCORDER_MODE_AUDIO, /**< Audio recording mode */
1345 } MMCamcorderModeType;
1348 * An enumeration for facing direction.
1351 MM_CAMCORDER_CAMERA_FACING_DIRECTION_REAR = 0, /**< Facing direction of camera is REAR */
1352 MM_CAMCORDER_CAMERA_FACING_DIRECTION_FRONT, /**< Facing direction of camera is FRONT */
1353 } MMCamcorderCameraFacingDirection;
1357 * An enumeration of Audio Format.
1360 MM_CAMCORDER_AUDIO_FORMAT_PCM_U8 = 0, /**< unsigned 8bit audio */
1361 MM_CAMCORDER_AUDIO_FORMAT_PCM_S16_LE = 2, /**< signed 16bit audio. Little endian. */
1362 } MMCamcorderAudioFormat;
1366 * An enumeration for color tone. Color tone provides an impression of
1367 * seeing through a tinted glass.
1369 enum MMCamcorderColorToneType {
1370 MM_CAMCORDER_COLOR_TONE_NONE = 0, /**< None */
1371 MM_CAMCORDER_COLOR_TONE_MONO, /**< Mono */
1372 MM_CAMCORDER_COLOR_TONE_SEPIA, /**< Sepia */
1373 MM_CAMCORDER_COLOR_TONE_NEGATIVE, /**< Negative */
1374 MM_CAMCORDER_COLOR_TONE_BLUE, /**< Blue */
1375 MM_CAMCORDER_COLOR_TONE_GREEN, /**< Green */
1376 MM_CAMCORDER_COLOR_TONE_AQUA, /**< Aqua */
1377 MM_CAMCORDER_COLOR_TONE_VIOLET, /**< Violet */
1378 MM_CAMCORDER_COLOR_TONE_ORANGE, /**< Orange */
1379 MM_CAMCORDER_COLOR_TONE_GRAY, /**< Gray */
1380 MM_CAMCORDER_COLOR_TONE_RED, /**< Red */
1381 MM_CAMCORDER_COLOR_TONE_ANTIQUE, /**< Antique */
1382 MM_CAMCORDER_COLOR_TONE_WARM, /**< Warm */
1383 MM_CAMCORDER_COLOR_TONE_PINK, /**< Pink */
1384 MM_CAMCORDER_COLOR_TONE_YELLOW, /**< Yellow */
1385 MM_CAMCORDER_COLOR_TONE_PURPLE, /**< Purple */
1386 MM_CAMCORDER_COLOR_TONE_EMBOSS, /**< Emboss */
1387 MM_CAMCORDER_COLOR_TONE_OUTLINE, /**< Outline */
1388 MM_CAMCORDER_COLOR_TONE_SOLARIZATION, /**< Solarization */
1389 MM_CAMCORDER_COLOR_TONE_SKETCH, /**< Sketch */
1390 MM_CAMCORDER_COLOR_TONE_WASHED, /**< Washed */
1391 MM_CAMCORDER_COLOR_TONE_VINTAGE_WARM, /**< Vintage warm */
1392 MM_CAMCORDER_COLOR_TONE_VINTAGE_COLD, /**< Vintage cold */
1393 MM_CAMCORDER_COLOR_TONE_POSTERIZATION, /**< Posterization */
1394 MM_CAMCORDER_COLOR_TONE_CARTOON, /**< Cartoon */
1395 MM_CAMCORDER_COLOR_TONE_SELECTIVE_RED, /**< Selective color - Red */
1396 MM_CAMCORDER_COLOR_TONE_SELECTIVE_GREEN, /**< Selective color - Green */
1397 MM_CAMCORDER_COLOR_TONE_SELECTIVE_BLUE, /**< Selective color - Blue */
1398 MM_CAMCORDER_COLOR_TONE_SELECTIVE_YELLOW, /**< Selective color - Yellow */
1399 MM_CAMCORDER_COLOR_TONE_SELECTIVE_RED_YELLOW, /**< Selective color - Red and Yellow */
1404 * An enumeration for white balance. White Balance is the control that adjusts
1405 * the camcorder's color sensitivity to match the prevailing color of white
1406 * outdoor light, yellower indoor light, or (sometimes) greenish fluorescent
1407 * light. White balance may be set either automatically or manually. White balance
1408 * may be set "incorrectly" on purpose to achieve special effects.
1410 enum MMCamcorderWhiteBalanceType {
1411 MM_CAMCORDER_WHITE_BALANCE_NONE = 0, /**< None */
1412 MM_CAMCORDER_WHITE_BALANCE_AUTOMATIC, /**< Automatic */
1413 MM_CAMCORDER_WHITE_BALANCE_DAYLIGHT, /**< Daylight */
1414 MM_CAMCORDER_WHITE_BALANCE_CLOUDY, /**< Cloudy */
1415 MM_CAMCORDER_WHITE_BALANCE_FLUOROSCENT, /**< Fluorescent */
1416 MM_CAMCORDER_WHITE_BALANCE_INCANDESCENT, /**< Incandescent */
1417 MM_CAMCORDER_WHITE_BALANCE_SHADE, /**< Shade */
1418 MM_CAMCORDER_WHITE_BALANCE_HORIZON, /**< Horizon */
1419 MM_CAMCORDER_WHITE_BALANCE_FLASH, /**< Flash */
1420 MM_CAMCORDER_WHITE_BALANCE_CUSTOM, /**< Custom */
1425 * An enumeration for scene mode. Scene mode gives the environment condition
1426 * for operating camcorder. The mode of operation can be in daylight, night and
1427 * backlight. It can be an automatic setting also.
1429 enum MMCamcorderSceneModeType {
1430 MM_CAMCORDER_SCENE_MODE_NORMAL = 0, /**< Normal */
1431 MM_CAMCORDER_SCENE_MODE_PORTRAIT, /**< Portrait */
1432 MM_CAMCORDER_SCENE_MODE_LANDSCAPE, /**< Landscape */
1433 MM_CAMCORDER_SCENE_MODE_SPORTS, /**< Sports */
1434 MM_CAMCORDER_SCENE_MODE_PARTY_N_INDOOR, /**< Party & indoor */
1435 MM_CAMCORDER_SCENE_MODE_BEACH_N_INDOOR, /**< Beach & indoor */
1436 MM_CAMCORDER_SCENE_MODE_SUNSET, /**< Sunset */
1437 MM_CAMCORDER_SCENE_MODE_DUSK_N_DAWN, /**< Dusk & dawn */
1438 MM_CAMCORDER_SCENE_MODE_FALL_COLOR, /**< Fall */
1439 MM_CAMCORDER_SCENE_MODE_NIGHT_SCENE, /**< Night scene */
1440 MM_CAMCORDER_SCENE_MODE_FIREWORK, /**< Firework */
1441 MM_CAMCORDER_SCENE_MODE_TEXT, /**< Text */
1442 MM_CAMCORDER_SCENE_MODE_SHOW_WINDOW, /**< Show window */
1443 MM_CAMCORDER_SCENE_MODE_CANDLE_LIGHT, /**< Candle light */
1444 MM_CAMCORDER_SCENE_MODE_BACKLIGHT, /**< Backlight */
1445 MM_CAMCORDER_SCENE_MODE_AQUA, /**< Aqua */
1450 * An enumeration for focusing .
1452 enum MMCamcorderFocusMode {
1453 MM_CAMCORDER_FOCUS_MODE_NONE = 0, /**< Focus mode is None */
1454 MM_CAMCORDER_FOCUS_MODE_PAN, /**< Pan focus mode*/
1455 MM_CAMCORDER_FOCUS_MODE_AUTO, /**< Autofocus mode*/
1456 MM_CAMCORDER_FOCUS_MODE_MANUAL, /**< Manual focus mode*/
1457 MM_CAMCORDER_FOCUS_MODE_TOUCH_AUTO, /**< Touch Autofocus mode*/
1458 MM_CAMCORDER_FOCUS_MODE_CONTINUOUS, /**< Continuous Autofocus mode*/
1463 * An enumeration for auto focus scan range (af scan range)
1465 enum MMCamcorderAutoFocusType {
1466 MM_CAMCORDER_AUTO_FOCUS_NONE = 0, /**< Scan autofocus is not set */
1467 MM_CAMCORDER_AUTO_FOCUS_NORMAL, /**< Scan autofocus normally*/
1468 MM_CAMCORDER_AUTO_FOCUS_MACRO, /**< Scan autofocus in macro mode(close distance)*/
1469 MM_CAMCORDER_AUTO_FOCUS_FULL, /**< Scan autofocus in full mode(all range scan, limited by dev spec)*/
1474 * An enumeration for focus state.
1475 * When 'MM_MESSAGE_CAMCORDER_FOCUS_CHANGED' is delievered through 'MMMessageCallback',
1476 * this enumeration will be set to 'code' of MMMessageParamType.
1478 enum MMCamcorderFocusStateType {
1479 MM_CAMCORDER_FOCUS_STATE_RELEASED = 0, /**< Focus released.*/
1480 MM_CAMCORDER_FOCUS_STATE_ONGOING, /**< Focus in pregress*/
1481 MM_CAMCORDER_FOCUS_STATE_FOCUSED, /**< Focus success*/
1482 MM_CAMCORDER_FOCUS_STATE_FAILED, /**< Focus failed*/
1487 * An enumeration for ISO.
1489 enum MMCamcorderISOType {
1490 MM_CAMCORDER_ISO_AUTO = 0, /**< ISO auto mode*/
1491 MM_CAMCORDER_ISO_50, /**< ISO 50*/
1492 MM_CAMCORDER_ISO_100, /**< ISO 100*/
1493 MM_CAMCORDER_ISO_200, /**< ISO 200*/
1494 MM_CAMCORDER_ISO_400, /**< ISO 400*/
1495 MM_CAMCORDER_ISO_800, /**< ISO 800*/
1496 MM_CAMCORDER_ISO_1600, /**< ISO 1600*/
1497 MM_CAMCORDER_ISO_3200, /**< ISO 3200*/
1498 MM_CAMCORDER_ISO_6400, /**< ISO 6400*/
1499 MM_CAMCORDER_ISO_12800, /**< ISO 12800*/
1503 * An enumeration for Automatic exposure.
1505 enum MMCamcorderAutoExposureType {
1506 MM_CAMCORDER_AUTO_EXPOSURE_OFF = 0, /**< AE off*/
1507 MM_CAMCORDER_AUTO_EXPOSURE_ALL, /**< AE on, XXX mode*/
1508 MM_CAMCORDER_AUTO_EXPOSURE_CENTER_1, /**< AE on, XXX mode*/
1509 MM_CAMCORDER_AUTO_EXPOSURE_CENTER_2, /**< AE on, XXX mode*/
1510 MM_CAMCORDER_AUTO_EXPOSURE_CENTER_3, /**< AE on, XXX mode*/
1511 MM_CAMCORDER_AUTO_EXPOSURE_SPOT_1, /**< AE on, XXX mode*/
1512 MM_CAMCORDER_AUTO_EXPOSURE_SPOT_2, /**< AE on, XXX mode*/
1513 MM_CAMCORDER_AUTO_EXPOSURE_CUSTOM_1, /**< AE on, XXX mode*/
1514 MM_CAMCORDER_AUTO_EXPOSURE_CUSTOM_2, /**< AE on, XXX mode*/
1519 * An enumeration for WDR mode .
1521 enum MMCamcorderWDRMode {
1522 MM_CAMCORDER_WDR_OFF = 0, /**< WDR OFF*/
1523 MM_CAMCORDER_WDR_ON, /**< WDR ON*/
1524 MM_CAMCORDER_WDR_AUTO, /**< WDR AUTO*/
1529 * An enumeration for HDR capture mode
1531 enum MMCamcorderHDRMode {
1532 MM_CAMCORDER_HDR_OFF = 0, /**< HDR OFF */
1533 MM_CAMCORDER_HDR_ON, /**< HDR ON and no original data - capture callback will be come once */
1534 MM_CAMCORDER_HDR_ON_AND_ORIGINAL, /**< HDR ON and original data - capture callback will be come twice(1st:Original, 2nd:HDR) */
1539 * An enumeration for Anti-handshake mode .
1541 enum MMCamcorderAHSMode {
1542 MM_CAMCORDER_AHS_OFF = 0, /**< AHS OFF*/
1543 MM_CAMCORDER_AHS_ON, /**< AHS ON*/
1544 MM_CAMCORDER_AHS_AUTO, /**< AHS AUTO*/
1545 MM_CAMCORDER_AHS_MOVIE, /**< AHS MOVIE*/
1550 * An enumeration for Video stabilization mode
1552 enum MMCamcorderVideoStabilizationMode {
1553 MM_CAMCORDER_VIDEO_STABILIZATION_OFF = 0, /**< Video Stabilization OFF*/
1554 MM_CAMCORDER_VIDEO_STABILIZATION_ON, /**< Video Stabilization ON*/
1559 * Geometry method for camcorder display.
1561 enum MMCamcorderGeometryMethod {
1562 MM_CAMCORDER_LETTER_BOX = 0, /**< Letter box*/
1563 MM_CAMCORDER_ORIGIN_SIZE, /**< Origin size*/
1564 MM_CAMCORDER_FULL, /**< full-screen*/
1565 MM_CAMCORDER_CROPPED_FULL, /**< Cropped full-screen*/
1566 MM_CAMCORDER_ORIGIN_OR_LETTER, /**< Origin size or Letter box*/
1567 MM_CAMCORDER_CUSTOM_ROI, /**< Explicitely described destination ROI*/
1572 * An enumeration for orientation values of tag .
1574 enum MMCamcorderTagOrientation {
1575 MM_CAMCORDER_TAG_ORT_NONE = 0, /**< No Orientation.*/
1576 MM_CAMCORDER_TAG_ORT_0R_VT_0C_VL, /**< The 0th row is at the visual top of the image, and the 0th column is the visual left-hand side.*/
1577 MM_CAMCORDER_TAG_ORT_0R_VT_0C_VR, /**< The 0th row is at the visual top of the image, and the 0th column is the visual right-hand side.*/
1578 MM_CAMCORDER_TAG_ORT_0R_VB_0C_VR, /**< The 0th row is at the visual bottom of the image, and the 0th column is the visual right-hand side.*/
1579 MM_CAMCORDER_TAG_ORT_0R_VB_0C_VL, /**< The 0th row is at the visual bottom of the image, and the 0th column is the visual left-hand side.*/
1580 MM_CAMCORDER_TAG_ORT_0R_VL_0C_VT, /**< The 0th row is the visual left-hand side of the image, and the 0th column is the visual top.*/
1581 MM_CAMCORDER_TAG_ORT_0R_VR_0C_VT, /**< The 0th row is the visual right-hand side of the image, and the 0th column is the visual top.*/
1582 MM_CAMCORDER_TAG_ORT_0R_VR_0C_VB, /**< The 0th row is the visual right-hand side of the image, and the 0th column is the visual bottom.*/
1583 MM_CAMCORDER_TAG_ORT_0R_VL_0C_VB, /**< The 0th row is the visual left-hand side of the image, and the 0th column is the visual bottom.*/
1587 * An enumeration for captured video orientation values of tag .
1589 enum MMCamcorderTagVideoOrientation {
1590 MM_CAMCORDER_TAG_VIDEO_ORT_NONE = 0, /**< No Orientation.*/
1591 MM_CAMCORDER_TAG_VIDEO_ORT_90, /**< 90 degree */
1592 MM_CAMCORDER_TAG_VIDEO_ORT_180, /**< 180 degree */
1593 MM_CAMCORDER_TAG_VIDEO_ORT_270, /**< 270 degree */
1599 * An enumeration for Strobe mode.
1601 enum MMCamcorderStrobeMode {
1602 MM_CAMCORDER_STROBE_MODE_OFF = 0, /**< Always off */
1603 MM_CAMCORDER_STROBE_MODE_ON, /**< Always splashes */
1604 MM_CAMCORDER_STROBE_MODE_AUTO, /**< Depending on intensity of light, strobe starts to flash. */
1605 MM_CAMCORDER_STROBE_MODE_REDEYE_REDUCTION, /**< Red eye reduction. Multiple flash before capturing. */
1606 MM_CAMCORDER_STROBE_MODE_SLOW_SYNC, /**< Slow sync. A type of curtain synchronization. */
1607 MM_CAMCORDER_STROBE_MODE_FRONT_CURTAIN, /**< Front curtain. A type of curtain synchronization. */
1608 MM_CAMCORDER_STROBE_MODE_REAR_CURTAIN, /**< Rear curtain. A type of curtain synchronization. */
1609 MM_CAMCORDER_STROBE_MODE_PERMANENT, /**< keep turned on until turning off */
1614 * An enumeration for Strobe Control.
1616 enum MMCamcorderStrobeControl {
1617 MM_CAMCORDER_STROBE_CONTROL_OFF = 0, /**< turn off the flash light */
1618 MM_CAMCORDER_STROBE_CONTROL_ON, /**< turn on the flash light */
1619 MM_CAMCORDER_STROBE_CONTROL_CHARGE, /**< charge the flash light */
1624 * An enumeration for Detection mode.
1626 enum MMCamcorderDetectMode {
1627 MM_CAMCORDER_DETECT_MODE_OFF = 0, /**< turn detection off */
1628 MM_CAMCORDER_DETECT_MODE_ON, /**< turn detection on */
1633 * An enumeration for recommended preview resolution.
1635 enum MMCamcorderPreviewType {
1636 MM_CAMCORDER_PREVIEW_TYPE_NORMAL = 0, /**< normal ratio like 4:3 */
1637 MM_CAMCORDER_PREVIEW_TYPE_WIDE, /**< wide ratio like 16:9 */
1638 MM_CAMCORDER_PREVIEW_TYPE_SQUARE, /**< square ratio like 1:1 */
1642 /**********************************
1644 **********************************/
1646 * An enumeration for attribute values types.
1649 MM_CAM_ATTRS_TYPE_INVALID = -1, /**< Type is invalid */
1650 MM_CAM_ATTRS_TYPE_INT, /**< Integer type attribute */
1651 MM_CAM_ATTRS_TYPE_DOUBLE, /**< Double type attribute */
1652 MM_CAM_ATTRS_TYPE_STRING, /**< UTF-8 String type attribute */
1653 MM_CAM_ATTRS_TYPE_DATA, /**< Pointer type attribute */
1658 * An enumeration for attribute validation type.
1661 MM_CAM_ATTRS_VALID_TYPE_INVALID = -1, /**< Invalid validation type */
1662 MM_CAM_ATTRS_VALID_TYPE_NONE, /**< Do not check validity */
1663 MM_CAM_ATTRS_VALID_TYPE_INT_ARRAY, /**< validity checking type of integer array */
1664 MM_CAM_ATTRS_VALID_TYPE_INT_RANGE, /**< validity checking type of integer range */
1665 MM_CAM_ATTRS_VALID_TYPE_DOUBLE_ARRAY, /**< validity checking type of double array */
1666 MM_CAM_ATTRS_VALID_TYPE_DOUBLE_RANGE, /**< validity checking type of double range */
1667 } MMCamAttrsValidType;
1671 * An enumeration for attribute access flag.
1674 MM_CAM_ATTRS_FLAG_DISABLED = 0, /**< None flag is set. This means the attribute is not allowed to use. */
1675 MM_CAM_ATTRS_FLAG_READABLE = 1 << 0, /**< Readable */
1676 MM_CAM_ATTRS_FLAG_WRITABLE = 1 << 1, /**< Writable */
1677 MM_CAM_ATTRS_FLAG_MODIFIED = 1 << 2, /**< Modified */
1678 MM_CAM_ATTRS_FLAG_RW = MM_CAM_ATTRS_FLAG_READABLE | MM_CAM_ATTRS_FLAG_WRITABLE, /**< Readable and Writable */
1682 /**********************************
1684 **********************************/
1686 * An enumeration for stream data type.
1689 MM_CAM_STREAM_DATA_YUV420 = 0, /**< YUV420 Packed type - 1 plane */
1690 MM_CAM_STREAM_DATA_YUV422, /**< YUV422 Packed type - 1 plane */
1691 MM_CAM_STREAM_DATA_YUV420SP, /**< YUV420 SemiPlannar type - 2 planes */
1692 MM_CAM_STREAM_DATA_YUV420P, /**< YUV420 Plannar type - 3 planes */
1693 MM_CAM_STREAM_DATA_YUV422P, /**< YUV422 Plannar type - 3 planes */
1694 MM_CAM_STREAM_DATA_ENCODED, /**< Encoded data type - 1 plane */
1695 MM_CAM_STREAM_DATA_DEPTH, /**< Depth data type - 1 plane */
1696 MM_CAM_STREAM_DATA_RGB /**< RGB data type - 1 plane */
1700 /*=======================================================================================
1701 | STRUCTURE DEFINITIONS |
1702 ========================================================================================*/
1704 * A structure for attribute information
1707 MMCamAttrsType type;
1708 MMCamAttrsFlag flag;
1709 MMCamAttrsValidType validity_type;
1712 * A union that describes validity of the attribute.
1713 * Only when type is 'MM_CAM_ATTRS_TYPE_INT' or 'MM_CAM_ATTRS_TYPE_DOUBLE',
1714 * the attribute can have validity.
1718 * Validity structure for integer array.
1721 int *array; /**< a pointer of array */
1722 int count; /**< size of array */
1723 int def; /**< default value. Real value not index of array */
1727 * Validity structure for integer range.
1730 int min; /**< minimum range */
1731 int max; /**< maximum range */
1732 int def; /**< default value */
1736 * Validity structure for double array.
1739 double *array; /**< a pointer of array */
1740 int count; /**< size of array */
1741 double def; /**< default value. Real value not index of array */
1745 * Validity structure for double range.
1748 double min; /**< minimum range */
1749 double max; /**< maximum range */
1750 double def; /**< default value */
1756 /* General Structure */
1758 * Structure for capture data.
1761 void *data; /**< pointer of captured image */
1762 unsigned int length; /**< length of captured image (in byte)*/
1763 MMPixelFormatType format; /**< image format */
1764 int width; /**< width of captured image */
1765 int height; /**< height of captured image */
1766 int encoder_type; /**< encoder type */
1767 } MMCamcorderCaptureDataType;
1771 * Structure for video stream data.
1773 #define BUFFER_MAX_PLANE_NUM 4
1779 unsigned int length_yuv;
1783 unsigned int length_y;
1785 unsigned int length_uv;
1789 unsigned int length_y;
1791 unsigned int length_u;
1793 unsigned int length_v;
1796 unsigned char *data;
1797 unsigned int length_data;
1798 } encoded, depth, rgb;
1799 } data; /**< pointer of captured stream */
1800 MMCamStreamData data_type; /**< data type */
1801 unsigned int length_total; /**< total length of stream buffer (in byte)*/
1802 unsigned int num_planes; /**< number of planes */
1803 MMPixelFormatType format; /**< image format */
1804 int width; /**< width of video buffer */
1805 int height; /**< height of video buffer */
1806 unsigned int timestamp; /**< timestamp of stream buffer (msec)*/
1807 void *bo[BUFFER_MAX_PLANE_NUM]; /**< TBM buffer object */
1808 void *internal_buffer; /**< Internal buffer pointer */
1809 int stride[BUFFER_MAX_PLANE_NUM]; /**< Stride of each plane */
1810 int elevation[BUFFER_MAX_PLANE_NUM]; /**< Elevation of each plane */
1811 } MMCamcorderVideoStreamDataType;
1815 * Structure for audio stream data.
1818 void *data; /**< pointer of captured stream */
1819 unsigned int length; /**< length of stream buffer (in byte)*/
1820 MMCamcorderAudioFormat format; /**< audio format */
1821 int channel; /**< number of channel of the stream */
1822 unsigned int timestamp; /**< timestamp of stream buffer (msec)*/
1823 float volume_dB; /**< dB value of audio stream */
1824 } MMCamcorderAudioStreamDataType;
1828 * Structure for muxed stream data.
1831 void *data; /**< pointer of muxed stream */
1832 unsigned int length; /**< length of stream buffer (in byte) */
1833 unsigned long long offset; /**< current offset for data */
1834 } MMCamcorderMuxedStreamDataType;
1838 * Prerequisite information for mm_camcorder_create()
1839 * The information to set prior to create.
1842 enum MMVideoDeviceType videodev_type; /**< Video device type */
1843 /* For future use */
1844 int reserved[4]; /**< reserved fields */
1849 * Report structure of recording file
1852 char *recording_filename; /**< File name of stored recording file. Please free after using. */
1853 } MMCamRecordingReport; /**< report structure definition of recording file */
1857 * Face detect defailed information
1859 typedef struct _MMCamFaceInfo {
1860 int id; /**< id of each face */
1861 int score; /**< score of each face */
1862 MMRectType rect; /**< area of face */
1866 * Face detect information
1868 typedef struct _MMCamFaceDetectInfo {
1869 int num_of_faces; /**< number of detected faces */
1870 MMCamFaceInfo *face_info; /**< face information, this should be freed after use it. */
1871 } MMCamFaceDetectInfo;
1874 * Window information
1876 typedef struct _MMCamWindowInfo {
1882 /*=======================================================================================
1883 | TYPE DEFINITIONS |
1884 ========================================================================================*/
1886 * Function definition for video stream callback.
1887 * Be careful! In this function, you can't call functions that change the state of camcorder such as mm_camcorder_stop(),
1888 * mm_camcorder_unrealize(), mm_camcorder_record(), mm_camcorder_commit(), and mm_camcorder_cancel(), etc.
1889 * Please don't hang this function long. It may cause low performance of preview or occur timeout error from video source.
1890 * Also, you're not allowed to call mm_camcorder_stop() even in other context, while you're hanging this function.
1891 * I recommend to you releasing this function ASAP.
1893 * @param[in] stream Reference pointer to video stream data
1894 * @param[in] user_param User parameter which is received from user when callback function was set
1895 * @return This function returns true on success, or false on failure.
1896 * @remarks This function is issued in the context of gstreamer (video sink thread).
1898 typedef gboolean (*mm_camcorder_video_stream_callback)(MMCamcorderVideoStreamDataType *stream, void *user_param);
1902 * Function definition for audio stream callback.
1903 * Be careful! In this function, you can't call functions that change the state of camcorder such as mm_camcorder_stop(),
1904 * mm_camcorder_unrealize(), mm_camcorder_record(), mm_camcorder_commit(), and mm_camcorder_cancel(), etc.
1905 * Please don't hang this function long. It may cause low performance of camcorder or occur timeout error from audio source.
1906 * I recommend to you releasing this function ASAP.
1908 * @param[in] stream Reference pointer to audio stream data
1909 * @param[in] user_param User parameter which is received from user when callback function was set
1910 * @return This function returns true on success, or false on failure.
1913 typedef gboolean (*mm_camcorder_audio_stream_callback)(MMCamcorderAudioStreamDataType *stream, void *user_param);
1917 * Function definition for muxed stream callback.
1918 * Be careful! In this function, you can't call functions that change the state of camcorder such as mm_camcorder_stop(),
1919 * mm_camcorder_unrealize(), mm_camcorder_record(), mm_camcorder_commit(), and mm_camcorder_cancel(), etc.
1920 * Please don't hang this function long. It may cause low performance of camcorder or occur timeout error from encoding pipeline.
1921 * I recommend to you releasing this function ASAP.
1923 * @param[in] stream Reference pointer to muxed stream data
1924 * @param[in] user_param User parameter which is received from user when callback function was set
1925 * @return This function returns true on success, or false on failure.
1928 typedef gboolean (*mm_camcorder_muxed_stream_callback)(MMCamcorderMuxedStreamDataType *stream, void *user_param);
1932 * Function definition for video capture callback.
1933 * Like '#mm_camcorder_video_stream_callback', you can't call mm_camcorder_stop() while you are hanging this function.
1935 * @param[in] frame Reference pointer to captured data
1936 * @param[in] thumbnail Reference pointer to thumbnail data
1937 * @param[in] user_param User parameter which is received from user when callback function was set
1938 * @return This function returns true on success, or false on failure.
1939 * @remarks This function is issued in the context of gstreamer (video src thread).
1941 typedef gboolean (*mm_camcorder_video_capture_callback)(MMCamcorderCaptureDataType *frame, MMCamcorderCaptureDataType *thumbnail, void *user_param);
1944 /*=======================================================================================
1945 | GLOBAL FUNCTION PROTOTYPES |
1946 ========================================================================================*/
1948 * mm_camcorder_create:\n
1949 * Create camcorder object. This is the function that an user who wants to use mm_camcorder calls first.
1950 * This function creates handle structure and initialize mutex, attributes, gstreamer.
1951 * When this function success, it will return a handle of newly created object.
1952 * A user have to put the handle when he calls every function of mm_camcorder. \n
1953 * Second argument of this function is the field to decribe pre-setting information of mm_camcorder such as which camera device it will use.
1954 * Normally, MM_VIDEO_DEVICE_CAMERA0 is for Main camera(or Mega camera, Back camera),
1955 * and MM_VIDEO_DEVICE_CAMERA1 is for VGA camera (or Front camera). If you want audio recording,
1956 * please set MM_VIDEO_DEVICE_NONE. (No camera device is needed.)
1958 * @param[out] camcorder A handle of camcorder.
1959 * @param[in] info Information for camera device. Depending on this information,
1960 * camcorder opens different camera devices.
1961 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
1962 * Please refer 'mm_error.h' to know the exact meaning of the error.
1963 * @see mm_camcorder_destroy
1965 * @post Next state of mm-camcorder will be MM_CAMCORDER_STATE_NULL
1966 * @remarks You can create multiple handles on a context at the same time. However,
1967 * camcorder cannot guarantee proper operation because of limitation of resources, such as
1968 * camera device, audio device, and display device.
1972 #include <mm_camcorder.h>
1974 gboolean initialize_camcorder()
1977 MMCamPreset cam_info;
1979 cam_info.videodev_type = MM_VIDEO_DEVICE_CAMERA0;
1981 // when you want to record audio only, enable this.
1982 cam_info.videodev_type = MM_VIDEO_DEVICE_NONE;
1985 err = mm_camcorder_create(&hcam, &cam_info);
1987 if (err != MM_ERROR_NONE) {
1988 printf("Fail to call mm_camcorder_create = %x\n", err);
1997 int mm_camcorder_create(MMHandleType *camcorder, MMCamPreset *info);
2001 * mm_camcorder_destroy:\n
2002 * Destroy camcorder object. Release handle and all of the resources that were created in mm_camcorder_create().\n
2003 * This is the finalizing function of mm_camcorder. If this function is not called or fails to call, the handle isn't released fully.
2004 * This function releases attributes, mutexes, sessions, and handle itself. This function also removes all of remaining messages.
2005 * So if your application should wait a certain message of mm_camcorder, please wait to call this function till getting the message.
2008 * @param[in] camcorder A handle of camcorder.
2009 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2010 * Please refer 'mm_error.h' to know the exact meaning of the error.
2011 * @see mm_camcorder_create
2012 * @pre Previous state of mm-camcorder should be MM_CAMCORDER_STATE_NULL
2013 * @post Because the handle is not valid, you can't check the state.
2018 #include <mm_camcorder.h>
2020 gboolean destroy_camcorder()
2024 //Destroy camcorder handle
2025 err = mm_camcorder_destroy(hcam);
2027 printf("Fail to call mm_camcorder_destroy = %x\n", err);
2036 int mm_camcorder_destroy(MMHandleType camcorder);
2040 * mm_camcorder_realize:\n
2041 * Allocate resources for camcorder and initialize it.
2042 * This also creates streamer pipeline. So you have to set attributes that are pivotal to create
2043 * the pipeline before calling this function. This function also takes a roll to manage confliction
2044 * between different applications which use camcorder. For example, if you try to use camcorder when
2045 * other application that is more important such as call application, this function will return
2046 * 'MM_ERROR_POLICY_BLOCKED'. On the contrary, if your application that uses camcorder starts to launch
2047 * while another application that uses speaker and has lower priority, your application will kick
2048 * another application.
2050 * @param[in] camcorder A handle of camcorder.
2051 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2052 * Please refer 'mm_error.h' to know the exact meaning of the error.
2053 * @see mm_camcorder_unrealize
2054 * @pre Previous state of mm-camcorder should be MM_CAMCORDER_STATE_NULL
2055 * @post Next state of mm-camcorder will be MM_CAMCORDER_STATE_READY
2060 #include <mm_camcorder.h>
2062 //For image capturing
2063 gboolean initialize_image_capture()
2066 MMCamPreset cam_info;
2067 char *err_attr_name = NULL;
2068 void * hdisplay = NULL;
2071 //Set video device as 'camera0' (main camera device)
2072 cam_info.videodev_type = MM_VIDEO_DEVICE_CAMERA0;
2074 err = mm_camcorder_create(&hcam, &cam_info);
2076 if (err != MM_ERROR_NONE) {
2077 printf("Fail to call mm_camcorder_create = %x\n", err);
2081 mm_camcorder_set_message_callback(hcam,(MMMessageCallback)msg_callback, (void*)hcam);
2082 mm_camcorder_set_video_capture_callback(hcam,(mm_camcorder_video_capture_callback)camcordertest_video_capture_cb, (void*)hcam);
2084 hdisplay = &ad.xid; //xid of xwindow. This value can be different depending on your environment.
2085 hsize = sizeof(ad.xid); //size of xid structure.
2087 // camcorder attribute setting
2088 err = mm_camcorder_set_attributes((MMHandleType)hcam, &err_attr_name,
2089 MMCAM_MODE, MM_CAMCORDER_MODE_IMAGE,
2090 MMCAM_IMAGE_ENCODER, MM_IMAGE_CODEC_JPEG,
2091 MMCAM_CAMERA_WIDTH, 640,
2092 MMCAM_CAMERA_HEIGHT, 480,
2093 MMCAM_CAMERA_FORMAT, MM_PIXEL_FORMAT_YUYV,
2094 MMCAM_CAMERA_FPS, 30,
2095 MMCAM_DISPLAY_ROTATION, MM_DISPLAY_ROTATION_270,
2096 MMCAM_DISPLAY_HANDLE, (void*) hdisplay, hsize,
2097 MMCAM_CAPTURE_FORMAT, MM_PIXEL_FORMAT_ENCODED,
2098 MMCAM_CAPTURE_WIDTH, 640,
2099 MMCAM_CAPTURE_HEIGHT, 480,
2103 printf("Set attrs fail. (%s:%x)\n", err_attr_name, err);
2104 if (err_attr_name) {
2105 free(err_attr_name);
2106 err_attr_name = NULL;
2111 err = mm_camcorder_realize(hcam);
2113 printf("Fail to call mm_camcorder_realize = %x\n", err);
2121 gboolean initialize_video_capture()
2124 MMCamPreset cam_info;
2125 char *err_attr_name = NULL;
2126 void * hdisplay = NULL;
2129 //Set video device as 'camera0' (main camera device)
2130 cam_info.videodev_type = MM_VIDEO_DEVICE_CAMERA0;
2132 err = mm_camcorder_create(&hcam, &cam_info);
2134 if (err != MM_ERROR_NONE) {
2135 printf("Fail to call mm_camcorder_create = %x\n", err);
2139 mm_camcorder_set_message_callback(hcam,(MMMessageCallback)msg_callback, hcam);
2141 hdisplay = &ad.xid; //xid of xwindow. This value can be different depending on your environment.
2142 hsize = sizeof(ad.xid); //size of xid structure.
2144 // camcorder attribute setting
2145 err = mm_camcorder_set_attributes((MMHandleType)hcam, &err_attr_name,
2146 MMCAM_MODE, MM_CAMCORDER_MODE_VIDEO,
2147 MMCAM_AUDIO_DEVICE, MM_AUDIO_DEVICE_MIC,
2148 MMCAM_AUDIO_ENCODER, MM_AUDIO_CODEC_AAC,
2149 MMCAM_VIDEO_ENCODER, MM_VIDEO_CODEC_MPEG4,
2150 MMCAM_FILE_FORMAT, MM_FILE_FORMAT_3GP,
2151 MMCAM_CAMERA_WIDTH, 1280,
2152 MMCAM_CAMERA_HEIGHT, 720,
2153 MMCAM_CAMERA_FORMAT, MM_PIXEL_FORMAT_NV12,
2154 MMCAM_CAMERA_FPS, 30,
2155 MMCAM_AUDIO_SAMPLERATE, 44100,
2156 MMCAM_AUDIO_FORMAT, MM_CAMCORDER_AUDIO_FORMAT_PCM_S16_LE,
2157 MMCAM_AUDIO_CHANNEL, 2,
2158 MMCAM_DISPLAY_ROTATION, MM_DISPLAY_ROTATION_270,
2159 MMCAM_DISPLAY_HANDLE, (void*) hdisplay, hsize,
2160 MMCAM_TARGET_FILENAME, TARGET_FILENAME, strlen(TARGET_FILENAME),
2164 printf("Set attrs fail. (%s:%x)\n", err_attr_name, err);
2165 if (err_attr_name) {
2166 free(err_attr_name);
2167 err_attr_name = NULL;
2172 err = mm_camcorder_realize(hcam);
2174 printf("Fail to call mm_camcorder_realize = %x\n", err);
2181 //For audio(only) capturing
2182 gboolean initialize_audio_capture()
2185 MMCamPreset cam_info;
2186 char *err_attr_name = NULL;
2187 void * hdisplay = NULL;
2190 //Set no video device, because audio recording doesn't need video input.
2191 cam_info.videodev_type = MM_VIDEO_DEVICE_NONE;
2193 err = mm_camcorder_create(&hcam, &cam_info);
2195 if (err != MM_ERROR_NONE) {
2196 printf("Fail to call mm_camcorder_create = %x\n", err);
2200 mm_camcorder_set_message_callback(hcam,(MMMessageCallback)msg_callback, (void*)hcam);
2202 hdisplay = &ad.xid; //xid of xwindow. This value can be different depending on your environment.
2203 hsize = sizeof(ad.xid); //size of xid structure.
2205 // camcorder attribute setting
2206 err = mm_camcorder_set_attributes((MMHandleType)hcam, &err_attr_name,
2207 MMCAM_MODE, MM_CAMCORDER_MODE_AUDIO,
2208 MMCAM_AUDIO_DEVICE, MM_AUDIO_DEVICE_MIC,
2209 MMCAM_AUDIO_ENCODER, MM_AUDIO_CODEC_AAC,
2210 MMCAM_FILE_FORMAT, MM_FILE_FORMAT_3GP,
2211 MMCAM_AUDIO_SAMPLERATE, 44100,
2212 MMCAM_AUDIO_FORMAT, MM_CAMCORDER_AUDIO_FORMAT_PCM_S16_LE,
2213 MMCAM_AUDIO_CHANNEL, 2,
2214 MMCAM_TARGET_FILENAME, TARGET_FILENAME, strlen(TARGET_FILENAME),
2215 MMCAM_TARGET_TIME_LIMIT, 360000,
2219 printf("Set attrs fail. (%s:%x)\n", err_attr_name, err);
2220 if (err_attr_name) {
2221 free(err_attr_name);
2222 err_attr_name = NULL;
2227 err = mm_camcorder_realize(hcam);
2229 printf("Fail to call mm_camcorder_realize = %x\n", err);
2237 int mm_camcorder_realize(MMHandleType camcorder);
2241 * mm_camcorder_unrealize:\n
2242 * Uninitialize camcoder resources and free allocated memory.
2243 * Most important resource that is released here is gstreamer pipeline of mm_camcorder.
2244 * Because most of resources, such as camera device, video display device, and audio I/O device, are operating on the gstreamer pipeline,
2245 * this function should be called to release its resources.
2247 * @param[in] camcorder A handle of camcorder.
2248 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2249 * Please refer 'mm_error.h' to know the exact meaning of the error.
2250 * @see mm_camcorder_realize
2251 * @pre Previous state of mm-camcorder should be MM_CAMCORDER_STATE_READY
2252 * @post Next state of mm-camcorder will be MM_CAMCORDER_STATE_NULL
2257 #include <mm_camcorder.h>
2259 gboolean unrealize_camcorder()
2263 //Release all resources of camcorder handle
2264 err = mm_camcorder_unrealize(hcam);
2266 printf("Fail to call mm_camcorder_unrealize = %x\n", err);
2275 int mm_camcorder_unrealize(MMHandleType camcorder);
2279 * mm_camcorder_start:\n
2280 * Start previewing. (Image/Video mode)
2281 * 'mm_camcorder_video_stream_callback' is activated after calling this function.
2283 * @param[in] camcorder A handle of camcorder.
2284 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2285 * Please refer 'mm_error.h' to know the exact meaning of the error.
2286 * @see mm_camcorder_stop
2287 * @pre Previous state of mm-camcorder should be MM_CAMCORDER_STATE_READY
2288 * @post Next state of mm-camcorder will be MM_CAMCORDER_STATE_PREPARE
2293 #include <mm_camcorder.h>
2295 //For image capturing
2296 gboolean initialize_image_capture()
2299 MMCamPreset cam_info;
2300 char *err_attr_name = NULL;
2301 void * hdisplay = NULL;
2304 //Set video device as 'camera0' (main camera device)
2305 cam_info.videodev_type = MM_VIDEO_DEVICE_CAMERA0;
2307 err = mm_camcorder_create(&hcam, &cam_info);
2309 if (err != MM_ERROR_NONE) {
2310 printf("Fail to call mm_camcorder_create = %x\n", err);
2314 mm_camcorder_set_message_callback(hcam,(MMMessageCallback)msg_callback, (void*)hcam);
2315 mm_camcorder_set_video_capture_callback(hcam,(mm_camcorder_video_capture_callback)camcordertest_video_capture_cb, (void*)hcam);
2317 hdisplay = &ad.xid; //xid of xwindow. This value can be different depending on your environment.
2318 hsize = sizeof(ad.xid); //size of xid structure.
2320 // camcorder attribute setting
2321 err = mm_camcorder_set_attributes((MMHandleType)hcam, &err_attr_name,
2322 MMCAM_MODE, MM_CAMCORDER_MODE_IMAGE,
2323 MMCAM_IMAGE_ENCODER, MM_IMAGE_CODEC_JPEG,
2324 MMCAM_CAMERA_WIDTH, 640,
2325 MMCAM_CAMERA_HEIGHT, 480,
2326 MMCAM_CAMERA_FORMAT, MM_PIXEL_FORMAT_YUYV,
2327 MMCAM_CAMERA_FPS, 30,
2328 MMCAM_DISPLAY_ROTATION, MM_DISPLAY_ROTATION_270,
2329 MMCAM_DISPLAY_HANDLE, (void*) hdisplay, hsize,
2330 MMCAM_CAPTURE_FORMAT, MM_PIXEL_FORMAT_ENCODED,
2331 MMCAM_CAPTURE_WIDTH, 640,
2332 MMCAM_CAPTURE_HEIGHT, 480,
2336 printf("Set attrs fail. (%s:%x)\n", err_attr_name, err);
2337 if (err_attr_name) {
2338 free(err_attr_name);
2339 err_attr_name = NULL;
2344 err = mm_camcorder_realize(hcam);
2346 printf("Fail to call mm_camcorder_realize = %x\n", err);
2351 err = mm_camcorder_start(hcam);
2353 printf("Fail to call mm_camcorder_start = %x\n", err);
2361 gboolean initialize_video_capture()
2364 MMCamPreset cam_info;
2365 char *err_attr_name = NULL;
2366 void * hdisplay = NULL;
2369 //Set video device as 'camera0' (main camera device)
2370 cam_info.videodev_type = MM_VIDEO_DEVICE_CAMERA0;
2372 err = mm_camcorder_create(&hcam, &cam_info);
2374 if (err != MM_ERROR_NONE) {
2375 printf("Fail to call mm_camcorder_create = %x\n", err);
2379 mm_camcorder_set_message_callback(hcam,(MMMessageCallback)msg_callback, hcam);
2381 hdisplay = &ad.xid; //xid of xwindow. This value can be different depending on your environment.
2382 hsize = sizeof(ad.xid); //size of xid structure.
2384 // camcorder attribute setting
2385 err = mm_camcorder_set_attributes((MMHandleType)hcam, &err_attr_name,
2386 MMCAM_MODE, MM_CAMCORDER_MODE_VIDEO,
2387 MMCAM_AUDIO_DEVICE, MM_AUDIO_DEVICE_MIC,
2388 MMCAM_AUDIO_ENCODER, MM_AUDIO_CODEC_AAC,
2389 MMCAM_VIDEO_ENCODER, MM_VIDEO_CODEC_MPEG4,
2390 MMCAM_FILE_FORMAT, MM_FILE_FORMAT_3GP,
2391 MMCAM_CAMERA_WIDTH, 1280,
2392 MMCAM_CAMERA_HEIGHT, 720,
2393 MMCAM_CAMERA_FORMAT, MM_PIXEL_FORMAT_NV12,
2394 MMCAM_CAMERA_FPS, 30,
2395 MMCAM_AUDIO_SAMPLERATE, 44100,
2396 MMCAM_AUDIO_FORMAT, MM_CAMCORDER_AUDIO_FORMAT_PCM_S16_LE,
2397 MMCAM_AUDIO_CHANNEL, 2,
2398 MMCAM_DISPLAY_ROTATION, MM_DISPLAY_ROTATION_270,
2399 MMCAM_DISPLAY_HANDLE, (void*) hdisplay, hsize,
2400 MMCAM_TARGET_FILENAME, TARGET_FILENAME, strlen(TARGET_FILENAME),
2404 printf("Set attrs fail. (%s:%x)\n", err_attr_name, err);
2405 if (err_attr_name) {
2406 free(err_attr_name);
2407 err_attr_name = NULL;
2412 err = mm_camcorder_realize(hcam);
2414 printf("Fail to call mm_camcorder_realize = %x\n", err);
2419 err = mm_camcorder_start(hcam);
2421 printf("Fail to call mm_camcorder_start = %x\n", err);
2428 //For audio(only) capturing
2429 gboolean initialize_audio_capture()
2432 MMCamPreset cam_info;
2433 char *err_attr_name = NULL;
2434 void * hdisplay = NULL;
2437 //Set no video device, because audio recording doesn't need video input.
2438 cam_info.videodev_type = MM_VIDEO_DEVICE_NONE;
2440 err = mm_camcorder_create(&hcam, &cam_info);
2442 if (err != MM_ERROR_NONE) {
2443 printf("Fail to call mm_camcorder_create = %x\n", err);
2447 mm_camcorder_set_message_callback(hcam,(MMMessageCallback)msg_callback, (void*)hcam);
2449 hdisplay = &ad.xid; //xid of xwindow. This value can be different depending on your environment.
2450 hsize = sizeof(ad.xid); //size of xid structure.
2452 // camcorder attribute setting
2453 err = mm_camcorder_set_attributes((MMHandleType)hcam, &err_attr_name,
2454 MMCAM_MODE, MM_CAMCORDER_MODE_AUDIO,
2455 MMCAM_AUDIO_DEVICE, MM_AUDIO_DEVICE_MIC,
2456 MMCAM_AUDIO_ENCODER, MM_AUDIO_CODEC_AAC,
2457 MMCAM_FILE_FORMAT, MM_FILE_FORMAT_3GP,
2458 MMCAM_AUDIO_SAMPLERATE, 44100,
2459 MMCAM_AUDIO_FORMAT, MM_CAMCORDER_AUDIO_FORMAT_PCM_S16_LE,
2460 MMCAM_AUDIO_CHANNEL, 2,
2461 MMCAM_TARGET_FILENAME, TARGET_FILENAME, strlen(TARGET_FILENAME),
2462 MMCAM_TARGET_TIME_LIMIT, 360000,
2466 printf("Set attrs fail. (%s:%x)\n", err_attr_name, err);
2467 if (err_attr_name) {
2468 free(err_attr_name);
2469 err_attr_name = NULL;
2474 err = mm_camcorder_realize(hcam);
2476 printf("Fail to call mm_camcorder_realize = %x\n", err);
2481 err = mm_camcorder_start(hcam);
2483 printf("Fail to call mm_camcorder_start = %x\n", err);
2491 int mm_camcorder_start(MMHandleType camcorder);
2495 * mm_camcorder_stop:\n
2496 * Stop previewing. (Image/Video mode)
2497 * This function will change the status of pipeline. If an application doesn't return callbacks
2498 * of camcorder, this function can be locked. For example, if your application still
2499 * holds '#mm_camcorder_video_capture_callback' or '#mm_camcorder_video_stream_callback',
2500 * this function could be hung. So users have to return every callback before calling this function.
2502 * @param[in] camcorder A handle of camcorder.
2503 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2504 * Please refer 'mm_error.h' to know the exact meaning of the error.
2505 * @see mm_camcorder_start
2506 * @pre Previous state of mm-camcorder should be MM_CAMCORDER_STATE_PREPARE
2507 * @post Next state of mm-camcorder will be MM_CAMCORDER_STATE_READY
2512 #include <mm_camcorder.h>
2514 gboolean stop_camcorder()
2519 err = mm_camcorder_stop(hcam);
2521 printf("Fail to call mm_camcorder_stop = %x\n", err);
2530 int mm_camcorder_stop(MMHandleType camcorder);
2534 * mm_camcorder_capture_start:\n
2535 * Start capturing of still images. (Image mode only)
2536 * Captured image will be delievered through 'mm_camcorder_video_capture_callback'.
2537 * So basically, the operation is working asynchronously. \n
2538 * When a user call this function, MSL will stop to retrieving preview from camera device.
2539 * Then set capture resolution, pixel format, and encoding type to camera driver. After resuming,
2540 * camera can get still image. A user will be notified by
2541 * 'MM_MESSAGE_CAMCORDER_CAPTURED' message when capturing succeed. When a user sets
2542 * multishot (by setting multiple number to MMCAM_CAPTURE_COUNT), the message
2543 * will be called multiple time. You can get the number of image from 'code' of
2544 * 'MMMessageParamType'.
2546 * @param[in] camcorder A handle of camcorder.
2547 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2548 * Please refer 'mm_error.h' to know the exact meaning of the error.
2549 * @see mm_camcorder_capture_stop
2550 * @pre Previous state of mm-camcorder should be MM_CAMCORDER_STATE_PREPARE
2551 * @post Next state of mm-camcorder will be MM_CAMCORDER_STATE_CAPTURING
2552 * @remarks To call this function, preview should be started successfully.\n
2553 * This function is a pair of mm_camcorder_capture_stop().
2554 * So user should call mm_camcorder_capture_stop() after getting captured image.
2558 #include <mm_camcorder.h>
2560 gboolean capturing_picture()
2564 err = mm_camcorder_capture_start(hcam);
2567 printf("Fail to call mm_camcorder_capture_start = %x\n", err);
2571 //mm_camcorder_capture_stop should be called after getting
2572 //MM_MESSAGE_CAMCORDER_CAPTURED message.
2580 int mm_camcorder_capture_start(MMHandleType camcorder);
2584 * mm_camcorder_capture_stop:\n
2585 * Stop capturing of still images. (Image mode only)
2586 * This function notifies the end of capturing and launch preview again.
2587 * Just as mm_camcorder_capture_start(), this funciton stops still image stream and set preview information such as
2588 * resolution, pixel format, and framerate to camera driver. Then it command to start preview.
2589 * If you don't call this, preview will not be displayed even though capturing was finished.
2591 * @param[in] camcorder A handle of camcorder.
2592 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2593 * Please refer 'mm_error.h' to know the exact meaning of the error.
2594 * @see mm_camcorder_capture_start
2595 * @pre Previous state of mm-camcorder should be MM_CAMCORDER_STATE_CAPTURING
2596 * @post Next state of mm-camcorder will be MM_CAMCORDER_STATE_PREPARE
2597 * @remarks To call this function, a user has to call mm_camcorder_capture_start() first.\n
2598 * This is not a function to stop multishot in the middle of operation. For that,
2599 * please use '#MMCAM_CAPTURE_BREAK_CONTINUOUS_SHOT' instead.
2603 #include <mm_camcorder.h>
2605 gboolean capturing_picture_stop()
2609 err = mm_camcorder_capture_stop(hcam);
2611 printf("Fail to call mm_camcorder_capture_stop = %x\n", err);
2615 //After calling upper function, preview will start.
2622 int mm_camcorder_capture_stop(MMHandleType camcorder);
2626 * mm_camcorder_record:\n
2627 * Start recording. (Audio/Video mode only)
2628 * Camcorder starts to write a file when you call this function. You can specify the name of file
2629 * using '#MMCAM_TARGET_FILENAME'. Beware, if you fail to call mm_camcorder_commit() or mm_camcorder_cancel(),
2630 * the recorded file is still on the storage.
2632 * @param[in] camcorder A handle of camcorder.
2633 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2634 * Please refer 'mm_error.h' to know the exact meaning of the error.
2635 * @see mm_camcorder_pause
2636 * @pre Previous state of mm-camcorder should be MM_CAMCORDER_STATE_PREPARE
2637 * @post Next state of mm-camcorder will be MM_CAMCORDER_STATE_RECORDING
2642 #include <mm_camcorder.h>
2644 gboolean record_and_cancel_video_file()
2649 err = mm_camcorder_record(hcam);
2651 printf("Fail to call mm_camcorder_record = %x\n", err);
2660 int mm_camcorder_record(MMHandleType camcorder);
2664 * mm_camcorder_pause:\n
2665 * Pause A/V recording or Audio recording. (Audio/Video mode only)
2666 * On video recording, you can see preview while on pausing. So mm_camcorder cuts video stream path to encoder and keep the flow to preview.
2667 * If you call mm_camcorder_commit() while on pausing, the recorded file only has Audio and Video stream which were generated before pause().
2669 * @param[in] camcorder A handle of camcorder.
2670 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2671 * Please refer 'mm_error.h' to know the exact meaning of the error.
2672 * @see mm_camcorder_record
2673 * @pre Previous state of mm-camcorder should be MM_CAMCORDER_STATE_RECORDING
2674 * @post Next state of mm-camcorder will be MM_CAMCORDER_STATE_PAUSED
2675 * @remarks Even though this function is for pausing recording, small amount of buffers could be recorded after pause().
2676 * Because the buffers which are existed in the queue were created before pause(), the buffers should be recorded.
2680 #include <mm_camcorder.h>
2682 gboolean record_pause_and_resume_recording()
2687 err = mm_camcorder_record(hcam);
2689 printf("Fail to call mm_camcorder_record = %x\n", err);
2693 // Wait while recording...
2696 err = mm_camcorder_pause(hcam);
2698 printf("Fail to call mm_camcorder_pause = %x\n", err);
2705 err = mm_camcorder_record(hcam);
2707 printf("Fail to call mm_camcorder_record = %x\n", err);
2717 int mm_camcorder_pause(MMHandleType camcorder);
2721 * mm_camcorder_commit:\n
2722 * Stop recording and save results. (Audio/Video mode only)\n
2723 * After starting recording, encoded data frame will be stored in the location specified in MMCAM_TARGET_FILENAME.
2724 * Some encoder or muxer require a certain type of finalizing such as adding some information to header.
2725 * This function takes that roll. So if you don't call this function after recording, the result file may not be playable.\n
2726 * After committing successfully, camcorder resumes displaying preview (video recording case).
2727 * Because this is the function for saving the recording result, the operation is available
2728 * only when the mode of camcorder is MM_CAMCORDER_MODE_AUDIO or MM_CAMCORDER_MODE_VIDEO.
2730 * @param[in] camcorder A handle of camcorder.
2731 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2732 * Please refer 'mm_error.h' to know the exact meaning of the error.
2733 * @see mm_camcorder_cancel
2734 * @pre Previous state of mm-camcorder should be MM_CAMCORDER_STATE_RECORDING
2735 * @post Next state of mm-camcorder will be MM_CAMCORDER_STATE_PREPARE
2736 * @remarks This function can take a few second when recording time is long.
2737 * and if there are only quite few input buffer from video src or audio src,
2738 * committing could be failed.
2742 #include <mm_camcorder.h>
2744 gboolean record_and_save_video_file()
2749 err = mm_camcorder_record(hcam);
2751 printf("Fail to call mm_camcorder_record = %x\n", err);
2755 // Wait while recording for test...
2756 // In normal case, mm_camcorder_record() and mm_camcorder_commit() aren't called in the same function.
2759 err = mm_camcorder_commit(hcam);
2761 printf("Fail to call mm_camcorder_commit = %x\n", err);
2770 int mm_camcorder_commit(MMHandleType camcorder);
2774 * mm_camcorder_cancel:\n
2775 * Stop recording and discard the result. (Audio/Video mode only)
2776 * When a user want to finish recording without saving the result file, this function can be used.
2777 * Like mm_camcorder_commit(), this function also stops recording, release related resources(like codec) ,and goes back to preview status.
2778 * However, instead of saving file, this function unlinks(delete) the result.\n
2779 * Because this is the function for canceling recording, the operation is available
2780 * only when mode is MM_CAMCORDER_MODE_AUDIO or MM_CAMCORDER_MODE_VIDEO.
2782 * @param[in] camcorder A handle of camcorder.
2783 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2784 * Please refer 'mm_error.h' to know the exact meaning of the error.
2785 * @see mm_camcorder_commit
2786 * @pre Previous state of mm-camcorder should be MM_CAMCORDER_STATE_RECORDING
2787 * @post Next state of mm-camcorder will be MM_CAMCORDER_STATE_PREPARE
2792 #include <mm_camcorder.h>
2794 gboolean record_and_cancel_video_file()
2799 err = mm_camcorder_record(hcam);
2801 printf("Fail to call mm_camcorder_record = %x\n", err);
2805 // Wait while recording...
2808 err = mm_camcorder_cancel(hcam);
2810 printf("Fail to call mm_camcorder_cancel = %x\n", err);
2819 int mm_camcorder_cancel(MMHandleType camcorder);
2823 * mm_camcorder_set_message_callback:\n
2824 * Set callback for receiving messages from camcorder. Through this callback function, camcorder
2825 * sends various message including status changes, asynchronous error, capturing, and limitations.
2826 * One thing you have to know is that message callback is working on the main loop of application.
2827 * So until releasing the main loop, message callback will not be called.
2829 * @param[in] camcorder A handle of camcorder.
2830 * @param[in] callback Function pointer of callback function. Please refer 'MMMessageCallback'.
2831 * @param[in] user_data User parameter for passing to callback function.
2832 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2833 * Please refer 'mm_error.h' to know the exact meaning of the error.
2834 * @see MMMessageCallback
2837 * @remarks registered 'callback' is called on main loop of the application. So until the main loop is released, 'callback' will not be called.
2841 #include <mm_camcorder.h>
2843 gboolean setting_msg_callback()
2846 mm_camcorder_set_message_callback(hcam,(MMMessageCallback)msg_callback, (void*)hcam);
2854 int mm_camcorder_set_message_callback(MMHandleType camcorder, MMMessageCallback callback, void *user_data);
2858 * mm_camcorder_set_video_stream_callback:\n
2859 * Set callback for user defined video stream callback function.
2860 * Users can retrieve video frame using registered callback.
2861 * The callback function holds the same buffer that will be drawed on the display device.
2862 * So if an user change the buffer, it will be displayed on the device.
2864 * @param[in] camcorder A handle of camcorder.
2865 * @param[in] callback Function pointer of callback function.
2866 * @param[in] user_data User parameter for passing to callback function.
2867 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2868 * Please refer 'mm_error.h' to know the exact meaning of the error.
2869 * @see mm_camcorder_video_stream_callback
2872 * @remarks registered 'callback' is called on internal thread of camcorder. Regardless of the status of main loop, this function will be called.
2876 #include <mm_camcorder.h>
2878 gboolean setting_video_stream_callback()
2881 mm_camcorder_set_video_stream_callback(hcam, (mm_camcorder_video_stream_callback)camcordertest_video_stream_cb, (void*)hcam);
2887 int mm_camcorder_set_video_stream_callback(MMHandleType camcorder, mm_camcorder_video_stream_callback callback, void *user_data);
2891 * mm_camcorder_set_video_capture_callback:\n
2892 * Set callback for user defined video capture callback function. (Image mode only)
2893 * mm_camcorder deliever captured image through the callback.\n
2894 * Normally, this function provides main captured image and thumnail image. But depending on the environment,
2895 * thumnail would not be available. Information related with main captured image and thumnail image is also included
2896 * in the argument of the callback function.
2897 * For more detail information of callback, please refer 'mm_camcorder_video_capture_callback'.
2899 * @param[in] camcorder A handle of camcorder.
2900 * @param[in] callback Function pointer of callback function.
2901 * @param[in] user_data User parameter for passing to callback function.
2902 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2903 * Please refer 'mm_error.h' to know the exact meaning of the error.
2904 * @see mm_camcorder_video_capture_callback
2907 * @remarks registered 'callback' is called on internal thread of camcorder. Regardless of the status of main loop, this function will be called.
2911 #include <mm_camcorder.h>
2913 gboolean setting_capture_callback()
2916 mm_camcorder_set_video_capture_callback(hcam,(mm_camcorder_video_capture_callback)camcordertest_video_capture_cb, (void*)hcam);
2922 int mm_camcorder_set_video_capture_callback(MMHandleType camcorder, mm_camcorder_video_capture_callback callback, void *user_data);
2926 * mm_camcorder_set_audio_stream_callback:\n
2927 * Set callback for user defined audio stream callback function.
2928 * Users can retrieve audio data using registered callback.
2929 * The callback function holds the same buffer that will be recorded.
2930 * So if an user change the buffer, the result file will has the buffer.
2932 * @param[in] camcorder A handle of camcorder.
2933 * @param[in] callback Function pointer of callback function.
2934 * @param[in] user_data User parameter for passing to callback function.
2935 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2936 * Please refer 'mm_error.h' to know the exact meaning of the error.
2937 * @see mm_camcorder_audio_stream_callback
2940 * @remarks registered 'callback' is called on internal thread of camcorder. Regardless of the status of main loop, this function will be called.
2944 #include <mm_camcorder.h>
2946 gboolean setting_audio_stream_callback()
2949 mm_camcorder_set_audio_stream_callback(hcam, (mm_camcorder_audio_stream_callback)camcordertest_audio_stream_cb, (void*)hcam);
2955 int mm_camcorder_set_audio_stream_callback(MMHandleType camcorder, mm_camcorder_audio_stream_callback callback, void *user_data);
2959 * mm_camcorder_set_muxed_stream_callback:\n
2960 * Set callback for user defined muxed stream callback function.
2961 * Users can retrieve muxed data using registered callback.
2962 * The callback function holds the same buffer that will be recorded.
2964 * @param[in] camcorder A handle of camcorder.
2965 * @param[in] callback Function pointer of callback function.
2966 * @param[in] user_data User parameter for passing to callback function.
2967 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2968 * Please refer 'mm_error.h' to know the exact meaning of the error.
2969 * @see mm_camcorder_muxed_stream_callback
2972 * @remarks registered 'callback' is called on internal thread of camcorder. Regardless of the status of main loop, this function will be called.
2976 #include <mm_camcorder.h>
2978 gboolean setting_muxed_stream_callback()
2981 mm_camcorder_set_muxed_stream_callback(hcam, (mm_camcorder_muxed_stream_callback)camcordertest_muxed_stream_cb, (void*)hcam);
2987 int mm_camcorder_set_muxed_stream_callback(MMHandleType camcorder, mm_camcorder_muxed_stream_callback callback, void *user_data);
2991 * mm_camcorder_get_state:\n
2992 * Get the current state of camcorder.
2993 * mm_camcorder is working on the base of its state. An user should check the state of mm_camcorder before calling its functions.
2994 * If the handle is avaiable, user can retrieve the value.
2996 * @param[in] camcorder A handle of camcorder.
2997 * @param[out] state On return, it contains current state of camcorder.
2998 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
2999 * Please refer 'mm_error.h' to know the exact meaning of the error.
3000 * @see MMCamcorderStateType
3007 #include <mm_camcorder.h>
3009 gboolean get_state_of_camcorder()
3011 MMCamcorderStateType state;
3013 //Get state of camcorder
3014 mm_camcorder_get_state(hcam, &state);
3015 printf("Current status is %d\n", state);
3022 int mm_camcorder_get_state(MMHandleType camcorder, MMCamcorderStateType *state);
3023 int mm_camcorder_get_state2(MMHandleType camcorder, MMCamcorderStateType *state, MMCamcorderStateType *old_state);
3027 * mm_camcorder_get_attributes:\n
3028 * Get attributes of camcorder with given attribute names. This function can get multiple attributes
3029 * simultaneously. If one of attribute fails, this function will stop at the point.
3030 * 'err_attr_name' let you know the name of the attribute.
3032 * @param[in] camcorder Specifies the camcorder handle.
3033 * @param[out] err_attr_name Specifies the name of attributes that made an error. If the function doesn't make an error, this will be null. @n
3034 * Free this variable after using.
3035 * @param[in] attribute_name attribute name that user want to get.
3036 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
3037 * Please refer 'mm_error.h' to know the exact meaning of the error.
3040 * @remarks You can retrieve multiple attributes at the same time. @n
3041 * This function must finish with 'NULL' argument. @n
3042 * ex) mm_camcorder_get_attributes(....... , NULL);
3043 * @see mm_camcorder_set_attributes
3047 #include <mm_camcorder.h>
3049 gboolean getting_attribute()
3052 MMCamPreset cam_info;
3053 char *err_attr_name = NULL;
3054 void * hdisplay = NULL;
3057 hdisplay = &ad.xid; //xid of xwindow. This value can be different depending on your environment.
3058 hsize = sizeof(ad.xid); //size of xid structure.
3060 // camcorder attribute setting
3061 err = mm_camcorder_get_attributes(hcamcorder, NULL, //The second is the argument for debugging. But you can skip this.
3062 MMCAM_MODE, &mode, //You have to input a pointer instead of variable itself.
3063 NULL); //mm_camcorder_set_attributes() should be finished with a NULL argument.
3070 int mm_camcorder_get_attributes(MMHandleType camcorder, char **err_attr_name, const char *attribute_name, ...) G_GNUC_NULL_TERMINATED;
3075 * mm_camcorder_set_attributes:\n
3076 * Set attributes of camcorder with given attribute names. This function can set multiple attributes
3077 * simultaneously. If one of attribute fails, this function will stop at the point.
3078 * 'err_attr_name' let you know the name of the attribute.
3080 * @param[in] camcorder Specifies the camcorder handle.
3081 * @param[out] err_attr_name Specifies the name of attributes that made an error. If the function doesn't make an error, this will be null. @n
3082 * Free this variable after using.
3083 * @param[in] attribute_name attribute name that user want to set.
3084 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
3085 * Please refer 'mm_error.h' to know the exact meaning of the error.
3088 * @remarks You can put multiple attributes to camcorder at the same time. @n
3089 * This function must finish with 'NULL' argument. @n
3090 * ex) mm_camcorder_set_attributes(....... , NULL);
3091 * @see mm_camcorder_get_attributes
3095 #include <mm_camcorder.h>
3097 gboolean setting_attribute()
3100 MMCamPreset cam_info;
3101 char *err_attr_name = NULL;
3102 void * hdisplay = NULL;
3105 hdisplay = &ad.xid; //xid of xwindow. This value can be different depending on your environment.
3106 hsize = sizeof(ad.xid); //size of xid structure.
3108 // camcorder attribute setting
3109 err = mm_camcorder_set_attributes((MMHandleType)hcam, &err_attr_name, //The second is the argument for debugging.
3110 MMCAM_MODE, MM_CAMCORDER_MODE_IMAGE,
3111 MMCAM_IMAGE_ENCODER, MM_IMAGE_CODEC_JPEG,
3112 MMCAM_CAMERA_WIDTH, 640,
3113 MMCAM_CAMERA_HEIGHT, 480,
3114 MMCAM_CAMERA_FORMAT, MM_PIXEL_FORMAT_YUYV,
3115 MMCAM_CAMERA_FPS, 30,
3116 MMCAM_DISPLAY_ROTATION, MM_DISPLAY_ROTATION_270,
3117 MMCAM_DISPLAY_HANDLE, (void*) hdisplay, hsize, //Beware some types require 'size' value, too. (STRING, DATA type attributes)
3118 MMCAM_CAPTURE_FORMAT, MM_PIXEL_FORMAT_ENCODED,
3119 MMCAM_CAPTURE_WIDTH, 640,
3120 MMCAM_CAPTURE_HEIGHT, 480,
3121 NULL); //mm_camcorder_set_attributes() should be finished with a NULL argument.
3124 printf("Set attrs fail. (%s:%x)\n", err_attr_name, err); //When the function failed, 'err_attr_name' has the name of attr that made the error.
3125 if (err_attr_name) {
3126 free(err_attr_name); //Please free 'err_attr_name', after using the argument.
3127 err_attr_name = NULL;
3136 int mm_camcorder_set_attributes(MMHandleType camcorder, char **err_attr_name, const char *attribute_name, ...) G_GNUC_NULL_TERMINATED;
3140 * mm_camcorder_get_attribute_info:\n
3141 * Get detail information of the attribute. To manager attributes, an user may want to know the exact character of the attribute,
3142 * such as type, flag, and validity. This is the function to provide such information.
3143 * Depending on the 'validity_type', validity union would be different. To know about the type of union, please refer 'MMCamAttrsInfo'.
3145 * @param[in] camcorder Specifies the camcorder handle.
3146 * @param[in] attribute_name attribute name that user want to get information.
3147 * @param[out] info a structure that holds information related with the attribute.
3148 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
3149 * Please refer 'mm_error.h' to know the exact meaning of the error.
3152 * @remarks If the function succeeds, 'info' holds detail information about the attribute, such as type,
3153 * flag, validity_type, validity_values, and default values.
3154 * @see mm_camcorder_get_attributes, mm_camcorder_set_attributes
3158 #include <mm_camcorder.h>
3160 gboolean getting_info_from_attribute()
3162 MMCamAttrsInfo info;
3165 err = mm_camcorder_get_attribute_info(handle, MMCAM_CAPTURE_HEIGHT, &info);
3167 printf("Fail to call mm_camcorder_get_attribute_info()");
3171 //Now 'info' has many information about 'MMCAM_CAPTURE_HEIGHT'
3177 int mm_camcorder_get_attribute_info(MMHandleType camcorder, const char *attribute_name, MMCamAttrsInfo *info);
3181 * mm_camcorder_get_fps_list_by_resolution:\n
3182 * Get detail information of the fps configure. To manager fps, an user may want to know the supported fps list by the current preview resolution,
3183 * Gives attribute information structure, from the configure data.
3184 * Depending on the 'validity_type', validity union would be different. To know about the type of union, please refer 'MMCamAttrsInfo'.
3186 * @param[in] camcorder Specifies the camcorder handle.
3187 * @param[in] width width value of the current Preview resolution.
3188 * @param[in] height height value of the current Preview resolution.
3189 * @param[out] fps_info a structure that holds information related with the attribute.
3190 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
3191 * Please refer 'mm_error.h' to know the exact meaning of the error.
3194 * @remarks If the function succeeds, 'info' holds detail information about the attribute, such as type,
3195 * flag, validity_type, validity_values, and default values.
3196 * @see mm_camcorder_get_attributes, mm_camcorder_set_attributes
3200 #include <mm_camcorder.h>
3202 gboolean getting_info_from_attribute()
3204 MMCamAttrsInfo info;
3207 err = mm_camcorder_get_fps_list_by_resolution(handle, width, height, &info);
3209 printf("Fail to call mm_camcorder_get_attribute_info()");
3213 //Now 'info' has many information about 'MMCAM_CAPTURE_HEIGHT'
3219 int mm_camcorder_get_fps_list_by_resolution(MMHandleType camcorder, int width, int height, MMCamAttrsInfo *fps_info);
3223 * mm_camcorder_init_focusing:\n
3224 * Initialize focusing. \n
3225 * This function stops focusing action and adjust the camera lens to initial position.
3226 * Some camera applciation requires to initialize its lens position after releasing half shutter. In that case,
3227 * this should be a good choice. Comparing with mm_camcorder_stop_focusing, this function not only stops focusing,
3228 * but also initialize the lens. Preview image might be out-focused after calling this function.
3229 * @param[in] camcorder A handle of camcorder.
3230 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
3231 * Please refer 'mm_error.h' to know the exact meaning of the error.
3232 * @pre The status of camcorder should be MM_CAMCORDER_STATE_PREPARE, MM_CAMCORDER_STATE_RECORDING, or MM_CAMCORDER_STATE_PAUSED.
3235 * @see mm_camcorder_start_focusing, mm_camcorder_stop_focusing
3239 #include <mm_camcorder.h>
3241 gboolean start_autofocus()
3244 char * err_attr_name = NULL;
3246 // Set focus mode to 'AUTO' and scan range to 'AF Normal'.
3247 //You just need to set these values one time. After that, just call mm_camcorder_start_focusing().
3248 err = mm_camcorder_set_attributes((MMHandleType)hcam, &err_attr_name,
3249 MMCAM_CAMERA_FOCUS_MODE, MM_CAMCORDER_FOCUS_MODE_AUTO,
3250 MMCAM_CAMERA_AF_SCAN_RANGE, MM_CAMCORDER_AUTO_FOCUS_NORMAL,
3254 printf("Set attrs fail. (%s:%x)\n", err_attr_name, err);
3255 if (err_attr_name) {
3256 free(err_attr_name);
3257 err_attr_name = NULL;
3262 mm_camcorder_init_focusing(hcam);
3263 mm_camcorder_start_focusing(hcam);
3264 printf("Waiting for adjusting focus\n");
3266 // Waiting for 'MM_MESSAGE_CAMCORDER_FOCUS_CHANGED'
3273 int mm_camcorder_init_focusing(MMHandleType camcorder);
3277 * mm_camcorder_start_focusing:\n
3278 * Start focusing. \n
3279 * This function command to start focusing opeartion. Because focusing operation depends on mechanic or electric module,
3280 * it may take small amount of time. (For ex, 500ms ~ 3sec). \n
3281 * This function works asynchronously. When an user call this function, it will return immediately.
3282 * However, focusing operation will continue until it gets results.
3283 * After finishing operation, you can get 'MM_MESSAGE_CAMCORDER_FOCUS_CHANGED' message.
3284 * 'param.code' of the message structure describes the fucusing was success or not.
3286 * @param[in] camcorder A handle of camcorder.
3287 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
3288 * Please refer 'mm_error.h' to know the exact meaning of the error.
3292 * @see mm_camcorder_init_focusing, mm_camcorder_stop_focusing
3296 #include <mm_camcorder.h>
3298 gboolean start_autofocus()
3301 char * err_attr_name = NULL;
3303 // Set focus mode to 'AUTO' and scan range to 'AF Normal'.
3304 //You just need to set these values one time. After that, just call mm_camcorder_start_focusing().
3305 err = mm_camcorder_set_attributes((MMHandleType)hcam, &err_attr_name,
3306 MMCAM_CAMERA_FOCUS_MODE, MM_CAMCORDER_FOCUS_MODE_AUTO,
3307 MMCAM_CAMERA_AF_SCAN_RANGE, MM_CAMCORDER_AUTO_FOCUS_NORMAL,
3311 printf("Set attrs fail. (%s:%x)\n", err_attr_name, err);
3312 if (err_attr_name) {
3313 free(err_attr_name);
3314 err_attr_name = NULL;
3319 mm_camcorder_init_focusing(hcam);
3320 mm_camcorder_start_focusing(hcam);
3321 printf("Waiting for adjusting focus\n");
3323 // Waiting for 'MM_MESSAGE_CAMCORDER_FOCUS_CHANGED'
3330 int mm_camcorder_start_focusing(MMHandleType camcorder);
3334 * mm_camcorder_stop_focusing:\n
3335 * Stop focusing. This function halts focusing operation.\n
3336 * This is the function to stop focusing in the middle of the operation. So if focusing is already finished or not started yet,
3337 * this function will do nothing.
3339 * @param[in] camcorder A handle of camcorder.
3340 * @return This function returns zero(MM_ERROR_NONE) on success, or negative value with error code.\n
3341 * Please refer 'mm_error.h' to know the exact meaning of the error.
3342 * @see mm_camcorder_init_focusing, mm_camcorder_start_focusing
3343 * @pre mm_camcorder_start_focusing() should be called before calling this function.
3349 #include <mm_camcorder.h>
3351 gboolean stop_autofocus()
3356 mm_camcorder_stop_focusing(hcam);
3363 int mm_camcorder_stop_focusing(MMHandleType camcorder);
3366 void mm_camcorder_emit_signal(MMHandleType camcorder, const char *object_name,
3367 const char *interface_name, const char *signal_name, int value);
3369 /* check compatability between codec and file format */
3370 int mm_camcorder_check_codec_fileformat_compatibility(const char *codec_type, int codec, int file_format);
3372 /* external storage state management */
3373 int mm_camcorder_manage_external_storage_state(MMHandleType camcorder, int storage_state);
3383 #endif /* __MM_CAMCORDER_H__ */