1 DOCS-IETF-CABLE-DEVICE-NOTIFICATION-MIB DEFINITIONS ::= BEGIN
8 FROM SNMPv2-SMI -- RFC 2578
15 FROM SNMPv2-CONF -- RFC 2580
24 FROM DOCS-CABLE-DEVICE-MIB -- RFC 2669
27 docsIfCmtsCmStatusMacAddress,
28 docsIfDocsisBaseCapability,
29 docsIfCmStatusDocsisOperMode,
30 docsIfCmStatusModulationType,
31 docsIfCmtsCmStatusDocsisRegMode,
32 docsIfCmtsCmStatusModulationType
33 FROM DOCS-IF-MIB -- RFC 4546
36 FROM IF-MIB; -- RFC 2863
38 docsDevNotifMIB MODULE-IDENTITY
40 LAST-UPDATED "200605240000Z" -- May 24, 2006
41 ORGANIZATION "IETF IP over Cable Data Network
46 Postal: Cisco Systems, Inc.
48 San Jose, CA 95134, U.S.A.
50 E-mail: azlina@cisco.com
55 San Diego, CA 92121, U.S.A.
57 E-mail: gnakanishi@motorola.com
59 IETF IPCDN Working Group
60 General Discussion: ipcdn@ietf.org
64 Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn
65 Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn
66 Co-chairs: Richard Woundy,
67 richard_woundy@cable.comcast.com
68 Jean-Francois Mule, jf.mule@cablelabs.com"
71 "The Event Notification MIB is an extension of the
72 CABLE DEVICE MIB. It defines various notification
73 objects for both cable modem and cable modem termination
74 systems. Two groups of SNMP notification objects are
75 defined. One group is for notifying cable modem events,
76 and one group is for notifying cable modem termination
79 DOCSIS defines numerous events, and each event is
80 assigned to a functional category. This MIB defines
81 a notification object for each functional category.
82 The varbinding list of each notification includes
83 information about the event that occurred on the
86 Copyright (C) The Internet Society (2006). This version
87 of this MIB module is part of RFC 4547; see the RFC
88 itself for full legal notices."
90 REVISION "200605240000Z" -- May 24, 2006
92 "Initial version, published as RFC 4547."
95 docsDevNotifControl OBJECT IDENTIFIER ::= { docsDevNotifMIB 1}
96 docsDevCmNotifs OBJECT IDENTIFIER ::= { docsDevNotifMIB 2 0 }
97 docsDevCmtsNotifs OBJECT IDENTIFIER ::= { docsDevNotifMIB 3 0 }
99 docsDevCmNotifControl OBJECT-TYPE
101 cmInitTLVUnknownNotif( 0),
102 cmDynServReqFailNotif( 1),
103 cmDynServRspFailNotif( 2),
104 cmDynServAckFailNotif( 3),
107 cmDynamicSANotif( 6),
109 cmSwUpgradeInitNotif( 8),
110 cmSwUpgradeFailNotif( 9),
111 cmSwUpgradeSuccessNotif( 10),
115 cmSwUpgradeCVCNotif( 11),
117 cmDCCReqFailNotif( 13),
118 cmDCCRspFailNotif( 14),
119 cmDCCAckFailNotif( 15)
121 MAX-ACCESS read-write
125 "The object is used to enable specific CM notifications.
126 For example, if the first bit is set, then
127 docsDevCmInitTLVUnknownNotif is enabled. If it is not set,
128 the notification is disabled. Note that notifications are
129 also under the control of the MIB modules defined in
132 If the device is rebooted,the value of this object SHOULD
133 revert to the default value.
136 ::= { docsDevNotifControl 1 }
138 docsDevCmtsNotifControl OBJECT-TYPE
140 cmtsInitRegReqFailNotif( 0),
141 cmtsInitRegRspFailNotif( 1),
142 cmtsInitRegAckFailNotif( 2),
143 cmtsDynServReqFailNotif( 3),
144 cmtsDynServRspFailNotif( 4),
145 cmtsDynServAckFailNotif( 5),
146 cmtsBpiInitNotif( 6),
148 cmtsDynamicSANotif( 8),
149 cmtsDCCReqFailNotif( 9),
150 cmtsDCCRspFailNotif( 10),
151 cmtsDCCAckFailNotif( 11)
153 MAX-ACCESS read-write
156 "The object is used to enable specific CMTS notifications.
157 For example, if the first bit is set, then
158 docsDevCmtsInitRegRspFailNotif is enabled. If it is not set,
159 the notification is disabled. Note that notifications are
160 also under the control of the MIB modules defined in
166 If the device is rebooted,the value of this object SHOULD
167 revert to the default value.
170 ::= { docsDevNotifControl 2 }
172 docsDevCmInitTLVUnknownNotif NOTIFICATION-TYPE
179 docsIfDocsisBaseCapability,
180 docsIfCmStatusDocsisOperMode,
181 docsIfCmStatusModulationType
185 "Notification to indicate that an unknown TLV was
186 encountered during the TLV parsing process.
188 This notification sends additional information about
189 the event by including the following objects in its
191 - docsDevEvLevel: the priority level associated with the
193 - docsDevEvId: the unique identifier of the event that
195 - docsDevEvText: a textual description of the event.
196 - ifPhysAddress: the MAC address of the cable
197 interface of this cable modem.
198 - docsIfCmCmtsAddress: the MAC address of the CMTS
199 to which the CM is connected (if there is a cable
200 card/interface in the CMTS, then it is actually the
201 MAC address of the cable interface to which it is
203 - docsIfDocsisBaseCapability: the highest
204 version of the DOCSIS specification (1.0, 1.1, 2.0)
205 that the device is capable of supporting.
206 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
207 that the CM is operating in.
208 - docsIfCmStatusModulationType: the upstream modulation
209 methodology used by the CM.
211 ::= { docsDevCmNotifs 1 }
217 docsDevCmDynServReqFailNotif NOTIFICATION-TYPE
224 docsIfDocsisBaseCapability,
225 docsIfCmStatusDocsisOperMode,
226 docsIfCmStatusModulationType
231 "A notification to report the failure of a dynamic service
232 request during the dynamic services process.
234 This notification sends additional information about
235 the event by including the following objects in its
237 - docsDevEvLevel: the priority level associated with the
239 - docsDevEvId: the unique identifier of the event that
241 - docsDevEvText: a textual description of the event.
242 - ifPhysAddress: the MAC address of the cable
243 interface of this cable modem.
244 - docsIfCmCmtsAddress: the MAC address of the CMTS
245 to which the CM is connected to (if there is a cable
246 card/interface in the CMTS, then it is actually the
247 MAC address of the cable interface to which it is
249 - docsIfDocsisBaseCapability: the highest
250 version of the DOCSIS specification (1.0, 1.1, 2.0)
251 that the device is capable of supporting.
252 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
253 that the CM is operating in.
254 - docsIfCmStatusModulationType: the upstream modulation
255 methodology used by the CM.
257 ::= { docsDevCmNotifs 2 }
259 docsDevCmDynServRspFailNotif NOTIFICATION-TYPE
269 docsIfDocsisBaseCapability,
270 docsIfCmStatusDocsisOperMode,
271 docsIfCmStatusModulationType
275 " A notification to report the failure of a dynamic service
276 response during the dynamic services process.
278 This notification sends additional information about
279 the event by including the following objects in its
281 - docsDevEvLevel: the priority level associated with the
283 - docsDevEvId: the unique identifier of the event that
285 - docsDevEvText: a textual description of the event.
286 - ifPhysAddress: the MAC address of the cable
287 interface of this cable modem.
288 - docsIfCmCmtsAddress: the MAC address of the CMTS
289 to which the CM is connected (if there is a cable
290 card/interface in the CMTS, then it is actually the
291 MAC address of the cable interface to which it is
293 - docsIfDocsisBaseCapability: the highest
294 version of the DOCSIS specification (1.0, 1.1, 2.0)
295 that the device is capable of supporting.
296 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
297 that the CM is operating in.
298 - docsIfCmStatusModulationType: the upstream modulation
299 methodology used by the CM.
301 ::= { docsDevCmNotifs 3}
303 docsDevCmDynServAckFailNotif NOTIFICATION-TYPE
310 docsIfDocsisBaseCapability,
311 docsIfCmStatusDocsisOperMode,
312 docsIfCmStatusModulationType
319 "A notification to report the failure of a dynamic service
320 acknowledgement during the dynamic services process.
322 This notification sends additional information about
323 the event by including the following objects in its
325 - docsDevEvLevel: the priority level associated with the
327 - docsDevEvId: the unique identifier of the event that
329 - docsDevEvText: a textual description of the event.
330 - ifPhysAddress: the MAC address of the cable
331 interface of this cable modem.
332 - docsIfCmCmtsAddress: the MAC address of the CMTS
333 to which the CM is connected (if there is a cable
334 card/interface in the CMTS, then it is actually the
335 MAC address of the cable interface to which it is
337 - docsIfDocsisBaseCapability: the highest
338 version of the DOCSIS specification (1.0, 1.1, 2.0)
339 that the device is capable of supporting.
340 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
341 that the CM is operating in.
342 - docsIfCmStatusModulationType: the upstream modulation
343 methodology used by the CM.
345 ::= { docsDevCmNotifs 4}
347 docsDevCmBpiInitNotif NOTIFICATION-TYPE
354 docsIfDocsisBaseCapability,
355 docsIfCmStatusDocsisOperMode,
356 docsIfCmStatusModulationType
360 "A notification to report the failure of a BPI
361 initialization attempt during the registration process.
363 This notification sends additional information about
364 the event by including the following objects in its
366 - docsDevEvLevel: the priority level associated with the
371 - docsDevEvId: the unique identifier of the event that
373 - docsDevEvText: a textual description of the event.
374 - ifPhysAddress: the MAC address of the cable
375 interface of this cable modem.
376 - docsIfCmCmtsAddress: the MAC address of the CMTS
377 to which the CM is connected (if there is a cable
378 card/interface in the CMTS, then it is actually the
379 MAC address of the cable interface to which it is
381 - docsIfDocsisBaseCapability: the highest
382 version of the DOCSIS specification (1.0, 1.1, 2.0)
383 that the device is capable of supporting.
384 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
385 that the CM is operating in.
386 - docsIfCmStatusModulationType: the upstream modulation
387 methodology used by the CM.
389 ::= { docsDevCmNotifs 5 }
391 docsDevCmBPKMNotif NOTIFICATION-TYPE
398 docsIfDocsisBaseCapability,
399 docsIfCmStatusDocsisOperMode,
400 docsIfCmStatusModulationType
404 "A notification to report the failure of a Baseline
405 Privacy Key Management (BPKM) operation.
407 This notification sends additional information about
408 the event by including the following objects in its
410 - docsDevEvLevel: the priority level associated with the
412 - docsDevEvId: the unique identifier of the event that
414 - docsDevEvText: a textual description of the event.
415 - ifPhysAddress: the MAC address of the cable
416 interface of this cable modem.
417 - docsIfCmCmtsAddress: the MAC address of the CMTS
421 to which the CM is connected (if there is a cable
422 card/interface in the CMTS, then it is actually the
423 MAC address of the cable interface to which it is
425 - docsIfDocsisBaseCapability: the highest
426 version of the DOCSIS specification (1.0, 1.1, 2.0)
427 that the device is capable of supporting.
428 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
429 that the CM is operating in.
430 - docsIfCmStatusModulationType: the upstream modulation
431 methodology used by the CM.
433 ::= { docsDevCmNotifs 6 }
435 docsDevCmDynamicSANotif NOTIFICATION-TYPE
442 docsIfDocsisBaseCapability,
443 docsIfCmStatusDocsisOperMode,
444 docsIfCmStatusModulationType
448 "A notification to report the failure of a dynamic security
449 association operation.
451 This notification sends additional information about
452 the event by including the following objects in its
454 - docsDevEvLevel: the priority level associated with the
456 - docsDevEvId: the unique identifier of the event that
458 - docsDevEvText: a textual description of the event.
459 - ifPhysAddress: the MAC address of the cable
460 interface of this cable modem.
461 - docsIfCmCmtsAddress: the MAC address of the CMTS
462 to which the CM is connected (if there is a cable
463 card/interface in the CMTS, then it is actually the
464 MAC address of the cable interface to which it is
466 - docsIfDocsisBaseCapability: the highest
467 version of the DOCSIS specification (1.0, 1.1, 2.0)
468 that the device is capable of supporting.
472 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
473 that the CM is operating in.
474 - docsIfCmStatusModulationType: the upstream modulation
475 methodology used by the CM.
477 ::= { docsDevCmNotifs 7 }
479 docsDevCmDHCPFailNotif NOTIFICATION-TYPE
487 docsIfDocsisBaseCapability,
488 docsIfCmStatusDocsisOperMode,
489 docsIfCmStatusModulationType
493 "A notification to report the failure of a DHCP operation.
495 This notification sends additional information about
496 the event by including the following objects in its
498 - docsDevEvLevel: the priority level associated with the
500 - docsDevEvId: the unique identifier of the event that
502 - docsDevEvText: a textual description of the event.
503 - ifPhysAddress: the MAC address of the cable
504 interface of this cable modem.
505 - docsIfCmCmtsAddress: the MAC address of the CMTS
506 to which the CM is connected (if there is a cable
507 card/interface in the CMTS, then it is actually the
508 MAC address of the cable interface to which it is
510 - docsDevServerDhcp: the IP address of the DHCP server.
511 - docsIfDocsisBaseCapability: the highest
512 version of the DOCSIS specification (1.0, 1.1, 2.0)
513 that the device is capable of supporting.
514 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
515 that the CM is operating in.
516 - docsIfCmStatusModulationType: the upstream modulation
517 methodology used by the CM.
519 ::= { docsDevCmNotifs 8 }
523 docsDevCmSwUpgradeInitNotif NOTIFICATION-TYPE
532 docsIfDocsisBaseCapability,
533 docsIfCmStatusDocsisOperMode,
534 docsIfCmStatusModulationType
538 "A notification to indicate that a software upgrade
539 has been initiated on the device.
541 This notification sends additional information about
542 the event by including the following objects in its
544 - docsDevEvLevel: the priority level associated with the
546 - docsDevEvId: the unique identifier of the event that
548 - docsDevEvText: a textual description of the event.
549 - ifPhysAddress: the MAC address of the cable
550 interface of this cable modem.
551 - docsIfCmCmtsAddress: the MAC address of the CMTS
552 to which the CM is connected (if there is a cable
553 card/interface in the CMTS, then it is actually the
554 MAC address of the cable interface to which it is
556 - docsIfDocsisBaseCapability: the highest
557 version of the DOCSIS specification (1.0, 1.1, 2.0)
558 that the device is capable of supporting.
559 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
560 that the CM is operating in.
561 - docsIfCmStatusModulationType: the upstream modulation
562 methodology used by the CM.
564 ::= { docsDevCmNotifs 9 }
566 docsDevCmSwUpgradeFailNotif NOTIFICATION-TYPE
578 docsIfDocsisBaseCapability,
579 docsIfCmStatusDocsisOperMode,
580 docsIfCmStatusModulationType
584 "A notification to report the failure of a software upgrade
587 This notification sends additional information about
588 the event by including the following objects in its
590 - docsDevEvLevel: the priority level associated with the
592 - docsDevEvId: the unique identifier of the event that
594 - docsDevEvText: a textual description of the event.
595 - ifPhysAddress: the MAC address of the cable
596 interface of this cable modem.
597 - docsIfCmCmtsAddress: the MAC address of the CMTS
598 to which the CM is connected (if there is a cable
599 card/interface in the CMTS, then it is actually the
600 MAC address of the cable interface to which it is
602 - docsDevSwFilename: the software image file name
603 - docsDevSwServer: the IP address of the server that
604 the image is retrieved from.
605 - docsIfDocsisBaseCapability: the highest
606 version of the DOCSIS specification (1.0, 1.1, 2.0)
607 that the device is capable of supporting.
608 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
609 that the CM is operating in.
610 - docsIfCmStatusModulationType: the upstream modulation
611 methodology used by the CM.
613 ::= { docsDevCmNotifs 10 }
615 docsDevCmSwUpgradeSuccessNotif NOTIFICATION-TYPE
627 docsIfDocsisBaseCapability,
628 docsIfCmStatusDocsisOperMode,
629 docsIfCmStatusModulationType
633 "A notification to report the software upgrade success
636 This notification sends additional information about
637 the event by including the following objects in its
639 - docsDevEvLevel: the priority level associated with the
641 - docsDevEvId: the unique identifier of the event that
643 - docsDevEvText: a textual description of the event.
644 - ifPhysAddress: the MAC address of the cable
645 interface of this cable modem.
646 - docsIfCmCmtsAddress: the MAC address of the CMTS
647 to which the CM is connected (if there is a cable
648 card/interface in the CMTS, then it is actually the
649 MAC address of the cable interface to which it is
651 - docsDevSwFilename: the software image file name
652 - docsDevSwServer: the IP address of the server that
653 the image is retrieved from.
654 - docsIfDocsisBaseCapability: the highest
655 version of the DOCSIS specification (1.0, 1.1, 2.0)
656 that the device is capable of supporting.
657 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
658 that the CM is operating in.
659 - docsIfCmStatusModulationType: the upstream modulation
660 methodology used by the CM.
662 ::= { docsDevCmNotifs 11 }
664 docsDevCmSwUpgradeCVCFailNotif NOTIFICATION-TYPE
671 docsIfDocsisBaseCapability,
672 docsIfCmStatusDocsisOperMode,
676 docsIfCmStatusModulationType
680 "A notification to report that the verification of the
681 code file has failed during a secure software upgrade
684 This notification sends additional information about
685 the event by including the following objects in its
687 - docsDevEvLevel: the priority level associated with the
689 - docsDevEvId: the unique identifier of the event that
691 - docsDevEvText: a textual description of the event.
692 - ifPhysAddress: the MAC address of the cable
693 interface of this cable modem.
694 - docsIfCmCmtsAddress: the MAC address of the CMTS
695 to which the CM is connected (if there is a cable
696 card/interface in the CMTS, then it is actually the
697 MAC address of the cable interface to which it is
699 - docsIfDocsisBaseCapability: the highest
700 version of the DOCSIS specification (1.0, 1.1, 2.0)
701 that the device is capable of supporting.
702 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
703 that the CM is operating in.
704 - docsIfCmStatusModulationType: the upstream modulation
705 methodology used by the CM.
707 ::= { docsDevCmNotifs 12 }
709 docsDevCmTODFailNotif NOTIFICATION-TYPE
717 docsIfDocsisBaseCapability,
718 docsIfCmStatusDocsisOperMode,
719 docsIfCmStatusModulationType
723 "A notification to report the failure of a time of day
729 This notification sends additional information about
730 the event by including the following objects in its
732 - docsDevEvLevel: the priority level associated with the
734 - docsDevEvId: the unique identifier of the event that
736 - docsDevEvText: a textual description of the event.
737 - ifPhysAddress: the MAC address of the cable
738 interface of this cable modem.
739 - docsIfCmCmtsAddress: the MAC address of the CMTS
740 to which the CM is connected (if there is a cable
741 card/interface in the CMTS, then it is actually the
742 MAC address of the cable interface to which it is
744 - docsDevServerTime: the IP address of the time server.
745 - docsIfDocsisBaseCapability: the highest
746 version of the DOCSIS specification (1.0, 1.1, 2.0)
747 that the device is capable of supporting.
748 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
749 that the CM is operating in.
750 - docsIfCmStatusModulationType: the upstream modulation
751 methodology used by the CM.
753 ::= { docsDevCmNotifs 13 }
755 docsDevCmDCCReqFailNotif NOTIFICATION-TYPE
762 docsIfDocsisBaseCapability,
763 docsIfCmStatusDocsisOperMode,
764 docsIfCmStatusModulationType
768 " A notification to report the failure of a dynamic channel
769 change request during the dynamic channel change process
772 This notification sends additional information about
773 the event by including the following objects in its
778 - docsDevEvLevel: the priority level associated with the
780 - docsDevEvId: the unique identifier of the event that
782 - docsDevEvText: a textual description of the event.
783 - ifPhysAddress: the MAC address of the cable
784 interface of this cable modem.
785 - docsIfCmCmtsAddress: the MAC address of the CMTS
786 to which the CM is connected (if there is a cable
787 card/interface in the CMTS, then it is actually the
788 MAC address of the cable interface to which it is
790 - docsIfDocsisBaseCapability: the highest
791 version of the DOCSIS specification (1.0, 1.1, 2.0)
792 that the device is capable of supporting.
793 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
794 that the CM is operating in.
795 - docsIfCmStatusModulationType: the upstream modulation
796 methodology used by the CM.
798 ::= { docsDevCmNotifs 14 }
800 docsDevCmDCCRspFailNotif NOTIFICATION-TYPE
807 docsIfDocsisBaseCapability,
808 docsIfCmStatusDocsisOperMode,
809 docsIfCmStatusModulationType
813 "A notification to report the failure of a dynamic channel
814 change response during the dynamic channel
815 change process on the CM.
817 This notification sends additional information about
818 the event by including the following objects in its
820 - docsDevEvLevel: the priority level associated with the
822 - docsDevEvId: the unique identifier of the event that
824 - docsDevEvText: a textual description of the event.
825 - ifPhysAddress: the MAC address of the cable
829 interface of this cable modem.
830 - docsIfCmCmtsAddress: the MAC address of the CMTS
831 to which the CM is connected (if there is a cable
832 card/interface in the CMTS, then it is actually the
833 MAC address of the cable interface to which it is
835 - docsIfDocsisBaseCapability: the highest
836 version of the DOCSIS specification (1.0, 1.1, 2.0)
837 that the device is capable of supporting.
838 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
839 that the CM is operating in.
840 - docsIfCmStatusModulationType: the upstream modulation
841 methodology used by the CM.
843 ::= { docsDevCmNotifs 15 }
845 docsDevCmDCCAckFailNotif NOTIFICATION-TYPE
852 docsIfDocsisBaseCapability,
853 docsIfCmStatusDocsisOperMode,
854 docsIfCmStatusModulationType
858 "A notification to report the failure of a dynamic channel
859 change acknowledgement during the dynamic channel
860 change process on the CM.
862 This notification sends additional information about
863 the event by including the following objects in its
866 - docsDevEvLevel: the priority level associated with the
868 - docsDevEvId: the unique identifier of the event that
870 - docsDevEvText: a textual description of the event.
871 - ifPhysAddress: the MAC address of the cable
872 interface of this cable modem.
873 - docsIfCmCmtsAddress: the MAC address of the CMTS
874 to which the CM is connected (if there is a cable
875 card/interface in the CMTS, then it is actually the
876 MAC address of the cable interface to which it is
881 - docsIfDocsisBaseCapability: the highest
882 version of the DOCSIS specification (1.0, 1.1, 2.0)
883 that the device is capable of supporting.
884 - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1)
885 that the CM is operating in.
886 - docsIfCmtsCmStatusModulationType the upstream modulation
887 methodology used by the CM.
889 ::= { docsDevCmNotifs 16}
891 docsDevCmtsInitRegReqFailNotif NOTIFICATION-TYPE
896 docsIfCmtsCmStatusMacAddress,
898 docsIfCmtsCmStatusDocsisRegMode,
899 docsIfDocsisBaseCapability,
900 docsIfCmtsCmStatusModulationType
904 "A notification to report the failure of a registration
905 request from a CM during the CM initialization
906 process that was detected on the CMTS.
908 This notification sends additional information about
909 the event by including the following objects in its
911 - docsDevEvLevel: the priority level associated with the
913 - docsDevEvId: the unique identifier of the event that
915 - docsDevEvText: a textual description of the event.
916 - docsIfCmtsCmStatusMacAddress: the MAC address of the CM
917 with which this notification is associated.
918 - ifPhysAddress: the MAC address of the CMTS
919 (if there is a cable card/interface in the CMTS,
920 then it is actually the MAC address of the cable
921 interface that connected to the CM) cable interface
923 - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
924 that the reporting CM is operating in.
925 - docsIfDocsisBaseCapability: the highest
926 version of the DOCSIS specification (1.0, 1.1, 2.0)
927 that the device is capable of supporting.
931 - docsIfCmtsCmStatusModulationType: the upstream
932 modulation methodology used by the CM.
934 ::= { docsDevCmtsNotifs 1 }
936 docsDevCmtsInitRegRspFailNotif NOTIFICATION-TYPE
941 docsIfCmtsCmStatusMacAddress,
943 docsIfCmtsCmStatusDocsisRegMode,
944 docsIfDocsisBaseCapability,
945 docsIfCmtsCmStatusModulationType
949 "A notification to report the failure of a registration
950 response during the CM initialization
951 process that was detected by the CMTS.
953 This notification sends additional information about
954 the event by including the following objects in its
956 - docsDevEvLevel: the priority level associated with the
958 - docsDevEvId: the unique identifier of the event that
960 - docsDevEvText: a textual description of the event.
961 - docsIfCmtsCmStatusMacAddress: the MAC address of the CM
962 with which this notification is associated.
963 - ifPhysAddress: the MAC address of the CMTS
964 (if there is a cable card/interface in the CMTS,
965 then it is actually the MAC address of the cable
966 interface that connected to the CM) cable interface
968 - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
969 that the reporting CM is operating in.
970 - docsIfDocsisBaseCapability: the highest
971 version of the DOCSIS specification (1.0, 1.1, 2.0)
972 that the device is capable of supporting.
973 - docsIfCmtsCmStatusModulationType: the upstream
974 modulation methodology used by the CM.
976 ::= { docsDevCmtsNotifs 2 }
978 docsDevCmtsInitRegAckFailNotif NOTIFICATION-TYPE
986 docsIfCmtsCmStatusMacAddress,
988 docsIfCmtsCmStatusDocsisRegMode,
989 docsIfDocsisBaseCapability,
990 docsIfCmtsCmStatusModulationType
994 "A notification to report the failure of a registration
995 acknowledgement from the CM during the CM
996 initialization process that was detected by the CMTS.
998 This notification sends additional information about
999 the event by including the following objects in its
1001 - docsDevEvLevel: the priority level associated with the
1003 - docsDevEvId: the unique identifier of the event that
1005 - docsDevEvText: a textual description of the event.
1006 - docsIfCmtsCmStatusMacAddress: the MAC address of the CM
1007 with which this notification is associated.
1008 - ifPhysAddress: the MAC address of the CMTS
1009 (if there is a cable card/interface in the CMTS,
1010 then it is actually the MAC address of the cable
1011 interface that connected to the CM) cable interface
1012 connected to the CM.
1013 - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
1014 that the reporting CM is operating in.
1015 - docsIfDocsisBaseCapability: the highest
1016 version of the DOCSIS specification (1.0, 1.1, 2.0)
1017 that the device is capable of supporting.
1018 - docsIfCmtsCmStatusModulationType: the upstream
1019 modulation methodology used by the CM.
1021 ::= { docsDevCmtsNotifs 3 }
1023 docsDevCmtsDynServReqFailNotif NOTIFICATION-TYPE
1028 docsIfCmtsCmStatusMacAddress,
1033 docsIfCmtsCmStatusDocsisRegMode,
1034 docsIfDocsisBaseCapability,
1035 docsIfCmtsCmStatusModulationType
1039 "A notification to report the failure of a dynamic service
1040 request during the dynamic services process
1041 that was detected by the CMTS.
1043 This notification sends additional information about
1044 the event by including the following objects in its
1046 - docsDevEvLevel: the priority level associated with the
1048 - docsDevEvId: the unique identifier of the event that
1050 - docsDevEvText: a textual description of the event.
1051 - docsIfCmtsCmStatusMacAddress: the MAC address of the CM
1052 with which this notification is associated.
1053 - ifPhysAddress: the MAC address of the CMTS
1054 (if there is a cable card/interface in the CMTS,
1055 then it is actually the MAC address of the cable
1056 interface that connected to the CM) cable interface
1057 connected to the CM.
1058 - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
1059 that the reporting CM is operating in.
1060 - docsIfDocsisBaseCapability: the highest
1061 version of the DOCSIS specification (1.0, 1.1, 2.0)
1062 that the device is capable of supporting.
1063 - docsIfCmtsCmStatusModulationType: the upstream
1064 modulation methodology used by the CM.
1066 ::= { docsDevCmtsNotifs 4 }
1068 docsDevCmtsDynServRspFailNotif NOTIFICATION-TYPE
1073 docsIfCmtsCmStatusMacAddress,
1075 docsIfCmtsCmStatusDocsisRegMode,
1076 docsIfDocsisBaseCapability,
1077 docsIfCmtsCmStatusModulationType
1084 "A notification to report the failure of a dynamic service
1085 response during the dynamic services process
1086 that was detected by the CMTS.
1088 This notification sends additional information about
1089 the event by including the following objects in its
1091 - docsDevEvLevel: the priority level associated with the
1093 - docsDevEvId: the unique identifier of the event that
1095 - docsDevEvText: a textual description of the event.
1096 - docsIfCmtsCmStatusMacAddress: the MAC address of the CM
1097 with which this notification is associated.
1098 - ifPhysAddress: the MAC address of the CMTS
1099 (if there is a cable card/interface in the CMTS,
1100 then it is actually the MAC address of the cable
1101 interface that connected to the CM) cable interface
1102 connected to the CM.
1103 - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
1104 that the reporting CM is operating in.
1105 - docsIfDocsisBaseCapability: the highest
1106 version of the DOCSIS specification (1.0, 1.1, 2.0)
1107 that the device is capable of supporting.
1108 - docsIfCmtsCmStatusModulationType: the upstream
1109 modulation methodology used by the CM.
1111 ::= { docsDevCmtsNotifs 5 }
1113 docsDevCmtsDynServAckFailNotif NOTIFICATION-TYPE
1118 docsIfCmtsCmStatusMacAddress,
1120 docsIfCmtsCmStatusDocsisRegMode,
1121 docsIfDocsisBaseCapability,
1122 docsIfCmtsCmStatusModulationType
1126 "A notification to report the failure of a dynamic service
1127 acknowledgement during the dynamic services
1128 process that was detected by the CMTS.
1130 This notification sends additional information about
1131 the event by including the following objects in its
1136 - docsDevEvLevel: the priority level associated with the
1138 - docsDevEvId: the unique identifier of the event that
1140 - docsDevEvText: a textual description of the event.
1141 - docsIfCmtsCmStatusMacAddress: the MAC address of the CM
1142 with which this notification is associated.
1143 - ifPhysAddress: the MAC address of the CMTS
1144 (if there is a cable card/interface in the CMTS,
1145 then it is actually the MAC address of the cable
1146 interface that connected to the CM) cable interface
1147 connected to the CM.
1148 - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
1149 that the reporting CM is operating in.
1150 - docsIfDocsisBaseCapability: the highest
1151 version of the DOCSIS specification (1.0, 1.1, 2.0)
1152 that the device is capable of supporting.
1153 - docsIfCmtsCmStatusModulationType: the upstream
1154 modulation methodology used by the CM.
1156 ::= { docsDevCmtsNotifs 6 }
1159 docsDevCmtsBpiInitNotif NOTIFICATION-TYPE
1164 docsIfCmtsCmStatusMacAddress,
1166 docsIfCmtsCmStatusDocsisRegMode,
1167 docsIfDocsisBaseCapability,
1168 docsIfCmtsCmStatusModulationType
1172 "A notification to report the failure of a BPI
1173 initialization attempt during the CM registration process
1174 that was detected by the CMTS.
1176 This notification sends additional information about
1177 the event by including the following objects in its
1179 - docsDevEvLevel: the priority level associated with the
1181 - docsDevEvId: the unique identifier of the event that
1186 - docsDevEvText: a textual description of the event.
1187 - docsIfCmtsCmStatusMacAddress: the MAC address of the CM
1188 with which this notification is associated.
1189 - ifPhysAddress: the MAC address of the CMTS
1190 (if there is a cable card/interface in the CMTS,
1191 then it is actually the MAC address of the cable
1192 interface that connected to the CM) cable interface
1193 connected to the CM.
1194 - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
1195 that the reporting CM is operating in.
1196 - docsIfDocsisBaseCapability: the highest
1197 version of the DOCSIS specification (1.0, 1.1, 2.0)
1198 that the device is capable of supporting.
1199 - docsIfCmtsCmStatusModulationType: the upstream
1200 modulation methodology used by the CM.
1202 ::= { docsDevCmtsNotifs 7 }
1204 docsDevCmtsBPKMNotif NOTIFICATION-TYPE
1209 docsIfCmtsCmStatusMacAddress,
1211 docsIfCmtsCmStatusDocsisRegMode,
1212 docsIfDocsisBaseCapability,
1213 docsIfCmtsCmStatusModulationType
1217 "A notification to report the failure of a BPKM operation
1218 that is detected by the CMTS.
1220 This notification sends additional information about
1221 the event by including the following objects in its
1223 - docsDevEvLevel: the priority level associated with the
1225 - docsDevEvId: the unique identifier of the event that
1227 - docsDevEvText: a textual description of the event.
1228 - docsIfCmtsCmStatusMacAddress: the MAC address of the CM
1229 with which this notification is associated.
1230 - ifPhysAddress: the MAC address of the CMTS
1231 (if there is a cable card/interface in the CMTS,
1232 then it is actually the MAC address of the cable
1233 interface that connected to the CM) cable interface
1237 connected to the CM.
1238 - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
1239 that the reporting CM is operating in.
1240 - docsIfDocsisBaseCapability: the highest
1241 version of the DOCSIS specification (1.0, 1.1, 2.0)
1242 that the device is capable of supporting.
1243 - docsIfCmtsCmStatusModulationType: the upstream
1244 modulation methodology used by the CM.
1246 ::= { docsDevCmtsNotifs 8 }
1248 docsDevCmtsDynamicSANotif NOTIFICATION-TYPE
1253 docsIfCmtsCmStatusMacAddress,
1255 docsIfCmtsCmStatusDocsisRegMode,
1256 docsIfDocsisBaseCapability,
1257 docsIfCmtsCmStatusModulationType
1261 "A notification to report the failure of a dynamic security
1262 association operation that is detected by the CMTS.
1264 This notification sends additional information about
1265 the event by including the following objects in its
1268 - docsDevEvLevel: the priority level associated with the
1270 - docsDevEvId: the unique identifier of the event that
1272 - docsDevEvText: a textual description of the event.
1273 - docsIfCmtsCmStatusMacAddress: the MAC address of the CM
1274 with which this notification is associated.
1275 - ifPhysAddress: the MAC address of the CMTS
1276 (if there is a cable card/interface in the CMTS,
1277 then it is actually the MAC address of the cable
1278 interface that connected to the CM) cable interface
1279 connected to the CM.
1280 - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
1281 that the reporting CM is operating in.
1282 - docsIfDocsisBaseCapability: the highest
1283 version of the DOCSIS specification (1.0, 1.1, 2.0)
1284 that the device is capable of supporting.
1288 - docsIfCmtsCmStatusModulationType: the upstream
1289 modulation methodology used by the CM.
1291 ::= { docsDevCmtsNotifs 9 }
1293 docsDevCmtsDCCReqFailNotif NOTIFICATION-TYPE
1298 docsIfCmtsCmStatusMacAddress,
1300 docsIfCmtsCmStatusDocsisRegMode,
1301 docsIfDocsisBaseCapability,
1302 docsIfCmtsCmStatusModulationType
1306 "A notification to report the failure of a dynamic channel
1307 change request during the dynamic channel
1308 change process and is detected by the CMTS.
1310 This notification sends additional information about
1311 the event by including the following objects in its
1313 - docsDevEvLevel: the priority level associated with the
1315 - docsDevEvId: the unique identifier of the event that
1317 - docsDevEvText: a textual description of the event.
1318 - docsIfCmtsCmStatusMacAddress: the MAC address of the CM
1319 with which this notification is associated.
1320 - ifPhysAddress: the MAC address of the CMTS
1321 (if there is a cable card/interface in the CMTS,
1322 then it is actually the MAC address of the cable
1323 interface that connected to the CM) cable interface
1324 connected to the CM.
1325 - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
1326 that the reporting CM is operating in.
1327 - docsIfDocsisBaseCapability: the highest
1328 version of the DOCSIS specification (1.0, 1.1, 2.0)
1329 that the device is capable of supporting.
1330 - docsIfCmtsCmStatusModulationType: the upstream
1331 modulation methodology used by the CM.
1333 ::= { docsDevCmtsNotifs 10 }
1335 docsDevCmtsDCCRspFailNotif NOTIFICATION-TYPE
1343 docsIfCmtsCmStatusMacAddress,
1345 docsIfCmtsCmStatusDocsisRegMode,
1346 docsIfDocsisBaseCapability,
1347 docsIfCmtsCmStatusModulationType
1351 "A notification to report the failure of a dynamic channel
1352 change response during the dynamic channel
1353 change process and is detected by the CMTS.
1355 This notification sends additional information about
1356 the event by including the following objects in its
1358 - docsDevEvLevel: the priority level associated with the
1360 - docsDevEvId: the unique identifier of the event that
1362 - docsDevEvText: a textual description of the event.
1364 - docsIfCmtsCmStatusMacAddress: the MAC address of the CM
1365 with which this notification is associated.
1366 - ifPhysAddress: the MAC address of the CMTS
1367 (if there is a cable card/interface in the CMTS,
1368 then it is actually the MAC address of the cable
1369 interface that connected to the CM) cable interface
1370 connected to the CM.
1371 - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
1372 that the reporting CM is operating in.
1373 - docsIfDocsisBaseCapability: the highest
1374 version of the DOCSIS specification (1.0, 1.1, 2.0)
1375 that the device is capable of supporting.
1376 - docsIfCmtsCmStatusModulationType: the upstream
1377 modulation methodology used by the CM.
1379 ::= { docsDevCmtsNotifs 11 }
1381 docsDevCmtsDCCAckFailNotif NOTIFICATION-TYPE
1386 docsIfCmtsCmStatusMacAddress,
1391 docsIfCmtsCmStatusDocsisRegMode,
1392 docsIfDocsisBaseCapability,
1393 docsIfCmtsCmStatusModulationType
1397 "A notification to report the failure of a dynamic channel
1398 change acknowledgement during the dynamic channel
1399 change process and is detected by the CMTS.
1401 This notification sends additional information about
1402 the event by including the following objects in its
1404 - docsDevEvLevel: the priority level associated with the
1406 - docsDevEvId: the unique identifier of the event that
1408 - docsDevEvText: a textual description of the event.
1409 - docsIfCmtsCmStatusMacAddress: the MAC address of the CM
1410 with which this notification is associated.
1411 - ifPhysAddress: the MAC address of the CMTS
1412 (if there is a cable card/interface in the CMTS,
1413 then it is actually the MAC address of the cable
1414 interface that connected to the CM) cable interface
1415 connected to the CM.
1416 - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1)
1417 that the reporting CM is operating in.
1418 - docsIfDocsisBaseCapability: the highest
1419 version of the DOCSIS specification (1.0, 1.1, 2.0)
1420 that the device is capable of supporting.
1421 - docsIfCmtsCmStatusModulationType: the upstream
1422 modulation methodology used by the CM.
1424 ::= { docsDevCmtsNotifs 12}
1427 --Conformance definitions
1430 docsDevNotifConformance OBJECT IDENTIFIER
1431 ::= { docsDevNotifMIB 4 }
1432 docsDevNotifGroups OBJECT IDENTIFIER
1433 ::= { docsDevNotifConformance 1 }
1434 docsDevNotifCompliances OBJECT IDENTIFIER
1435 ::= { docsDevNotifConformance 2 }
1436 docsDevCmNotifCompliance MODULE-COMPLIANCE
1442 "The compliance statement for CM Notifications and Control."
1444 MODULE --docsDevNotif
1446 docsDevCmNotifControlGroup,
1447 docsDevCmNotificationGroup
1449 ::= { docsDevNotifCompliances 1 }
1451 docsDevCmNotifControlGroup OBJECT-GROUP
1453 docsDevCmNotifControl
1457 "This group represents objects that allow control
1458 over CM Notifications."
1459 ::= { docsDevNotifGroups 1 }
1461 docsDevCmNotificationGroup NOTIFICATION-GROUP
1463 docsDevCmInitTLVUnknownNotif,
1464 docsDevCmDynServReqFailNotif,
1465 docsDevCmDynServRspFailNotif,
1466 docsDevCmDynServAckFailNotif,
1467 docsDevCmBpiInitNotif,
1469 docsDevCmDynamicSANotif,
1470 docsDevCmDHCPFailNotif,
1471 docsDevCmSwUpgradeInitNotif,
1472 docsDevCmSwUpgradeFailNotif,
1473 docsDevCmSwUpgradeSuccessNotif,
1474 docsDevCmSwUpgradeCVCFailNotif,
1475 docsDevCmTODFailNotif,
1476 docsDevCmDCCReqFailNotif,
1477 docsDevCmDCCRspFailNotif,
1478 docsDevCmDCCAckFailNotif
1482 "A collection of CM notifications providing device status
1484 ::= { docsDevNotifGroups 2 }
1486 docsDevCmtsNotifCompliance MODULE-COMPLIANCE
1492 "The compliance statement for DOCSIS CMTS Notification
1494 MODULE --docsDevNotif
1496 docsDevCmtsNotifControlGroup,
1497 docsDevCmtsNotificationGroup
1499 ::= { docsDevNotifCompliances 2 }
1501 docsDevCmtsNotifControlGroup OBJECT-GROUP
1503 docsDevCmtsNotifControl
1507 "This group represents objects that allow control
1508 over CMTS Notifications."
1509 ::= { docsDevNotifGroups 3 }
1511 docsDevCmtsNotificationGroup NOTIFICATION-GROUP
1513 docsDevCmtsInitRegReqFailNotif,
1514 docsDevCmtsInitRegRspFailNotif,
1515 docsDevCmtsInitRegAckFailNotif ,
1516 docsDevCmtsDynServReqFailNotif,
1517 docsDevCmtsDynServRspFailNotif,
1518 docsDevCmtsDynServAckFailNotif,
1519 docsDevCmtsBpiInitNotif,
1520 docsDevCmtsBPKMNotif,
1521 docsDevCmtsDynamicSANotif,
1522 docsDevCmtsDCCReqFailNotif,
1523 docsDevCmtsDCCRspFailNotif,
1524 docsDevCmtsDCCAckFailNotif
1528 "A collection of CMTS notifications providing device
1529 status and control."
1530 ::= { docsDevNotifGroups 4 }