1 /* SPDX-License-Identifier: GPL-2.0-only */
3 * linux/include/linux/mmc/host.h
5 * Host driver specific definitions.
7 #ifndef LINUX_MMC_HOST_H
8 #define LINUX_MMC_HOST_H
10 #include <linux/sched.h>
11 #include <linux/device.h>
12 #include <linux/fault-inject.h>
14 #include <linux/mmc/core.h>
15 #include <linux/mmc/card.h>
16 #include <linux/mmc/pm.h>
17 #include <linux/dma-direction.h>
18 #include <linux/blk-crypto-profile.h>
21 unsigned int clock; /* clock rate */
23 unsigned int power_delay_ms; /* waiting for stable power */
25 /* vdd stores the bit number of the selected voltage range from below. */
27 unsigned char bus_mode; /* command output mode */
29 #define MMC_BUSMODE_OPENDRAIN 1
30 #define MMC_BUSMODE_PUSHPULL 2
32 unsigned char chip_select; /* SPI chip select */
34 #define MMC_CS_DONTCARE 0
38 unsigned char power_mode; /* power supply mode */
40 #define MMC_POWER_OFF 0
41 #define MMC_POWER_UP 1
42 #define MMC_POWER_ON 2
43 #define MMC_POWER_UNDEFINED 3
45 unsigned char bus_width; /* data bus width */
47 #define MMC_BUS_WIDTH_1 0
48 #define MMC_BUS_WIDTH_4 2
49 #define MMC_BUS_WIDTH_8 3
51 unsigned char timing; /* timing specification used */
53 #define MMC_TIMING_LEGACY 0
54 #define MMC_TIMING_MMC_HS 1
55 #define MMC_TIMING_SD_HS 2
56 #define MMC_TIMING_UHS_SDR12 3
57 #define MMC_TIMING_UHS_SDR25 4
58 #define MMC_TIMING_UHS_SDR50 5
59 #define MMC_TIMING_UHS_SDR104 6
60 #define MMC_TIMING_UHS_DDR50 7
61 #define MMC_TIMING_MMC_DDR52 8
62 #define MMC_TIMING_MMC_HS200 9
63 #define MMC_TIMING_MMC_HS400 10
64 #define MMC_TIMING_SD_EXP 11
65 #define MMC_TIMING_SD_EXP_1_2V 12
67 unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */
69 #define MMC_SIGNAL_VOLTAGE_330 0
70 #define MMC_SIGNAL_VOLTAGE_180 1
71 #define MMC_SIGNAL_VOLTAGE_120 2
73 unsigned char drv_type; /* driver type (A, B, C, D) */
75 #define MMC_SET_DRIVER_TYPE_B 0
76 #define MMC_SET_DRIVER_TYPE_A 1
77 #define MMC_SET_DRIVER_TYPE_C 2
78 #define MMC_SET_DRIVER_TYPE_D 3
80 bool enhanced_strobe; /* hs400es selection */
83 struct mmc_clk_phase {
89 #define MMC_NUM_CLK_PHASES (MMC_TIMING_MMC_HS400 + 1)
90 struct mmc_clk_phase_map {
91 struct mmc_clk_phase phase[MMC_NUM_CLK_PHASES];
108 MMC_ERR_CMDQ_REQ_TIMEOUT,
110 MMC_ERR_CTRL_TIMEOUT,
111 MMC_ERR_UNEXPECTED_IRQ,
115 struct mmc_host_ops {
117 * It is optional for the host to implement pre_req and post_req in
118 * order to support double buffering of requests (prepare one
119 * request while another request is active).
120 * pre_req() must always be followed by a post_req().
121 * To undo a call made to pre_req(), call post_req() with
122 * a nonzero err condition.
124 void (*post_req)(struct mmc_host *host, struct mmc_request *req,
126 void (*pre_req)(struct mmc_host *host, struct mmc_request *req);
127 void (*request)(struct mmc_host *host, struct mmc_request *req);
128 /* Submit one request to host in atomic context. */
129 int (*request_atomic)(struct mmc_host *host,
130 struct mmc_request *req);
133 * Avoid calling the next three functions too often or in a "fast
134 * path", since underlaying controller might implement them in an
135 * expensive and/or slow way. Also note that these functions might
136 * sleep, so don't call them in the atomic contexts!
140 * Notes to the set_ios callback:
141 * ios->clock might be 0. For some controllers, setting 0Hz
142 * as any other frequency works. However, some controllers
143 * explicitly need to disable the clock. Otherwise e.g. voltage
144 * switching might fail because the SDCLK is not really quiet.
146 void (*set_ios)(struct mmc_host *host, struct mmc_ios *ios);
149 * Return values for the get_ro callback should be:
150 * 0 for a read/write card
151 * 1 for a read-only card
152 * -ENOSYS when not supported (equal to NULL callback)
153 * or a negative errno value when something bad happened
155 int (*get_ro)(struct mmc_host *host);
158 * Return values for the get_cd callback should be:
159 * 0 for a absent card
160 * 1 for a present card
161 * -ENOSYS when not supported (equal to NULL callback)
162 * or a negative errno value when something bad happened
164 int (*get_cd)(struct mmc_host *host);
166 void (*enable_sdio_irq)(struct mmc_host *host, int enable);
167 /* Mandatory callback when using MMC_CAP2_SDIO_IRQ_NOTHREAD. */
168 void (*ack_sdio_irq)(struct mmc_host *host);
170 /* optional callback for HC quirks */
171 void (*init_card)(struct mmc_host *host, struct mmc_card *card);
173 int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios);
175 /* Check if the card is pulling dat[0] low */
176 int (*card_busy)(struct mmc_host *host);
178 /* The tuning command opcode value is different for SD and eMMC cards */
179 int (*execute_tuning)(struct mmc_host *host, u32 opcode);
181 /* Prepare HS400 target operating frequency depending host driver */
182 int (*prepare_hs400_tuning)(struct mmc_host *host, struct mmc_ios *ios);
184 /* Execute HS400 tuning depending host driver */
185 int (*execute_hs400_tuning)(struct mmc_host *host, struct mmc_card *card);
187 /* Prepare switch to DDR during the HS400 init sequence */
188 int (*hs400_prepare_ddr)(struct mmc_host *host);
190 /* Prepare for switching from HS400 to HS200 */
191 void (*hs400_downgrade)(struct mmc_host *host);
193 /* Complete selection of HS400 */
194 void (*hs400_complete)(struct mmc_host *host);
196 /* Prepare enhanced strobe depending host driver */
197 void (*hs400_enhanced_strobe)(struct mmc_host *host,
198 struct mmc_ios *ios);
199 int (*select_drive_strength)(struct mmc_card *card,
200 unsigned int max_dtr, int host_drv,
201 int card_drv, int *drv_type);
202 /* Reset the eMMC card via RST_n */
203 void (*card_hw_reset)(struct mmc_host *host);
204 void (*card_event)(struct mmc_host *host);
207 * Optional callback to support controllers with HW issues for multiple
208 * I/O. Returns the number of supported blocks for the request.
210 int (*multi_io_quirk)(struct mmc_card *card,
211 unsigned int direction, int blk_size);
213 /* Initialize an SD express card, mandatory for MMC_CAP2_SD_EXP. */
214 int (*init_sd_express)(struct mmc_host *host, struct mmc_ios *ios);
218 /* Allocate resources, and make the CQE operational */
219 int (*cqe_enable)(struct mmc_host *host, struct mmc_card *card);
220 /* Free resources, and make the CQE non-operational */
221 void (*cqe_disable)(struct mmc_host *host);
223 * Issue a read, write or DCMD request to the CQE. Also deal with the
224 * effect of ->cqe_off().
226 int (*cqe_request)(struct mmc_host *host, struct mmc_request *mrq);
227 /* Free resources (e.g. DMA mapping) associated with the request */
228 void (*cqe_post_req)(struct mmc_host *host, struct mmc_request *mrq);
230 * Prepare the CQE and host controller to accept non-CQ commands. There
231 * is no corresponding ->cqe_on(), instead ->cqe_request() is required
234 void (*cqe_off)(struct mmc_host *host);
236 * Wait for all CQE tasks to complete. Return an error if recovery
239 int (*cqe_wait_for_idle)(struct mmc_host *host);
241 * Notify CQE that a request has timed out. Return false if the request
242 * completed or true if a timeout happened in which case indicate if
243 * recovery is needed.
245 bool (*cqe_timeout)(struct mmc_host *host, struct mmc_request *mrq,
246 bool *recovery_needed);
248 * Stop all CQE activity and prepare the CQE and host controller to
249 * accept recovery commands.
251 void (*cqe_recovery_start)(struct mmc_host *host);
253 * Clear the queue and call mmc_cqe_request_done() on all requests.
254 * Requests that errored will have the error set on the mmc_request
255 * (data->error or cmd->error for DCMD). Requests that did not error
256 * will have zero data bytes transferred.
258 void (*cqe_recovery_finish)(struct mmc_host *host);
261 struct mmc_async_req {
262 /* active mmc request */
263 struct mmc_request *mrq;
265 * Check error status of completed mmc request.
266 * Returns 0 if success otherwise non zero.
268 enum mmc_blk_status (*err_check)(struct mmc_card *, struct mmc_async_req *);
272 * struct mmc_slot - MMC slot functions
274 * @cd_irq: MMC/SD-card slot hotplug detection IRQ or -EINVAL
275 * @handler_priv: MMC/SD-card slot context
277 * Some MMC/SD host controllers implement slot-functions like card and
278 * write-protect detection natively. However, a large number of controllers
279 * leave these functions to the CPU. This struct provides a hook to attach
280 * such slot-function drivers.
284 bool cd_wake_enabled;
289 * mmc_context_info - synchronization details for mmc context
290 * @is_done_rcv wake up reason was done request
291 * @is_new_req wake up reason was new request
292 * @is_waiting_last_req mmc context waiting for single running request
295 struct mmc_context_info {
298 bool is_waiting_last_req;
299 wait_queue_head_t wait;
306 struct regulator *vmmc; /* Card power supply */
307 struct regulator *vqmmc; /* Optional Vccq supply */
311 struct task_struct *task;
315 struct device *parent;
316 struct device class_dev;
318 const struct mmc_host_ops *ops;
319 struct mmc_pwrseq *pwrseq;
324 u32 ocr_avail_sdio; /* SDIO-specific OCR */
325 u32 ocr_avail_sd; /* SD-specific OCR */
326 u32 ocr_avail_mmc; /* MMC-specific OCR */
327 struct wakeup_source *ws; /* Enable consume of uevents */
332 #define MMC_VDD_165_195 0x00000080 /* VDD voltage 1.65 - 1.95 */
333 #define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */
334 #define MMC_VDD_21_22 0x00000200 /* VDD voltage 2.1 ~ 2.2 */
335 #define MMC_VDD_22_23 0x00000400 /* VDD voltage 2.2 ~ 2.3 */
336 #define MMC_VDD_23_24 0x00000800 /* VDD voltage 2.3 ~ 2.4 */
337 #define MMC_VDD_24_25 0x00001000 /* VDD voltage 2.4 ~ 2.5 */
338 #define MMC_VDD_25_26 0x00002000 /* VDD voltage 2.5 ~ 2.6 */
339 #define MMC_VDD_26_27 0x00004000 /* VDD voltage 2.6 ~ 2.7 */
340 #define MMC_VDD_27_28 0x00008000 /* VDD voltage 2.7 ~ 2.8 */
341 #define MMC_VDD_28_29 0x00010000 /* VDD voltage 2.8 ~ 2.9 */
342 #define MMC_VDD_29_30 0x00020000 /* VDD voltage 2.9 ~ 3.0 */
343 #define MMC_VDD_30_31 0x00040000 /* VDD voltage 3.0 ~ 3.1 */
344 #define MMC_VDD_31_32 0x00080000 /* VDD voltage 3.1 ~ 3.2 */
345 #define MMC_VDD_32_33 0x00100000 /* VDD voltage 3.2 ~ 3.3 */
346 #define MMC_VDD_33_34 0x00200000 /* VDD voltage 3.3 ~ 3.4 */
347 #define MMC_VDD_34_35 0x00400000 /* VDD voltage 3.4 ~ 3.5 */
348 #define MMC_VDD_35_36 0x00800000 /* VDD voltage 3.5 ~ 3.6 */
350 u32 caps; /* Host capabilities */
352 #define MMC_CAP_4_BIT_DATA (1 << 0) /* Can the host do 4 bit transfers */
353 #define MMC_CAP_MMC_HIGHSPEED (1 << 1) /* Can do MMC high-speed timing */
354 #define MMC_CAP_SD_HIGHSPEED (1 << 2) /* Can do SD high-speed timing */
355 #define MMC_CAP_SDIO_IRQ (1 << 3) /* Can signal pending SDIO IRQs */
356 #define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */
357 #define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */
358 #define MMC_CAP_8_BIT_DATA (1 << 6) /* Can the host do 8 bit transfers */
359 #define MMC_CAP_AGGRESSIVE_PM (1 << 7) /* Suspend (e)MMC/SD at idle */
360 #define MMC_CAP_NONREMOVABLE (1 << 8) /* Nonremovable e.g. eMMC */
361 #define MMC_CAP_WAIT_WHILE_BUSY (1 << 9) /* Waits while card is busy */
362 #define MMC_CAP_3_3V_DDR (1 << 11) /* Host supports eMMC DDR 3.3V */
363 #define MMC_CAP_1_8V_DDR (1 << 12) /* Host supports eMMC DDR 1.8V */
364 #define MMC_CAP_1_2V_DDR (1 << 13) /* Host supports eMMC DDR 1.2V */
365 #define MMC_CAP_DDR (MMC_CAP_3_3V_DDR | MMC_CAP_1_8V_DDR | \
367 #define MMC_CAP_POWER_OFF_CARD (1 << 14) /* Can power off after boot */
368 #define MMC_CAP_BUS_WIDTH_TEST (1 << 15) /* CMD14/CMD19 bus width ok */
369 #define MMC_CAP_UHS_SDR12 (1 << 16) /* Host supports UHS SDR12 mode */
370 #define MMC_CAP_UHS_SDR25 (1 << 17) /* Host supports UHS SDR25 mode */
371 #define MMC_CAP_UHS_SDR50 (1 << 18) /* Host supports UHS SDR50 mode */
372 #define MMC_CAP_UHS_SDR104 (1 << 19) /* Host supports UHS SDR104 mode */
373 #define MMC_CAP_UHS_DDR50 (1 << 20) /* Host supports UHS DDR50 mode */
374 #define MMC_CAP_UHS (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 | \
375 MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | \
377 #define MMC_CAP_SYNC_RUNTIME_PM (1 << 21) /* Synced runtime PM suspends. */
378 #define MMC_CAP_NEED_RSP_BUSY (1 << 22) /* Commands with R1B can't use R1. */
379 #define MMC_CAP_DRIVER_TYPE_A (1 << 23) /* Host supports Driver Type A */
380 #define MMC_CAP_DRIVER_TYPE_C (1 << 24) /* Host supports Driver Type C */
381 #define MMC_CAP_DRIVER_TYPE_D (1 << 25) /* Host supports Driver Type D */
382 #define MMC_CAP_DONE_COMPLETE (1 << 27) /* RW reqs can be completed within mmc_request_done() */
383 #define MMC_CAP_CD_WAKE (1 << 28) /* Enable card detect wake */
384 #define MMC_CAP_CMD_DURING_TFR (1 << 29) /* Commands during data transfer */
385 #define MMC_CAP_CMD23 (1 << 30) /* CMD23 supported. */
386 #define MMC_CAP_HW_RESET (1 << 31) /* Reset the eMMC card via RST_n */
388 u32 caps2; /* More host capabilities */
390 #define MMC_CAP2_BOOTPART_NOACC (1 << 0) /* Boot partition no access */
391 #define MMC_CAP2_FULL_PWR_CYCLE (1 << 2) /* Can do full power cycle */
392 #define MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND (1 << 3) /* Can do full power cycle in suspend */
393 #define MMC_CAP2_HS200_1_8V_SDR (1 << 5) /* can support */
394 #define MMC_CAP2_HS200_1_2V_SDR (1 << 6) /* can support */
395 #define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \
396 MMC_CAP2_HS200_1_2V_SDR)
397 #define MMC_CAP2_SD_EXP (1 << 7) /* SD express via PCIe */
398 #define MMC_CAP2_SD_EXP_1_2V (1 << 8) /* SD express 1.2V */
399 #define MMC_CAP2_CD_ACTIVE_HIGH (1 << 10) /* Card-detect signal active high */
400 #define MMC_CAP2_RO_ACTIVE_HIGH (1 << 11) /* Write-protect signal active high */
401 #define MMC_CAP2_NO_PRESCAN_POWERUP (1 << 14) /* Don't power up before scan */
402 #define MMC_CAP2_HS400_1_8V (1 << 15) /* Can support HS400 1.8V */
403 #define MMC_CAP2_HS400_1_2V (1 << 16) /* Can support HS400 1.2V */
404 #define MMC_CAP2_HS400 (MMC_CAP2_HS400_1_8V | \
406 #define MMC_CAP2_HSX00_1_8V (MMC_CAP2_HS200_1_8V_SDR | MMC_CAP2_HS400_1_8V)
407 #define MMC_CAP2_HSX00_1_2V (MMC_CAP2_HS200_1_2V_SDR | MMC_CAP2_HS400_1_2V)
408 #define MMC_CAP2_SDIO_IRQ_NOTHREAD (1 << 17)
409 #define MMC_CAP2_NO_WRITE_PROTECT (1 << 18) /* No physical write protect pin, assume that card is always read-write */
410 #define MMC_CAP2_NO_SDIO (1 << 19) /* Do not send SDIO commands during initialization */
411 #define MMC_CAP2_HS400_ES (1 << 20) /* Host supports enhanced strobe */
412 #define MMC_CAP2_NO_SD (1 << 21) /* Do not send SD commands during initialization */
413 #define MMC_CAP2_NO_MMC (1 << 22) /* Do not send (e)MMC commands during initialization */
414 #define MMC_CAP2_CQE (1 << 23) /* Has eMMC command queue engine */
415 #define MMC_CAP2_CQE_DCMD (1 << 24) /* CQE can issue a direct command */
416 #define MMC_CAP2_AVOID_3_3V (1 << 25) /* Host must negotiate down from 3.3V */
417 #define MMC_CAP2_MERGE_CAPABLE (1 << 26) /* Host can merge a segment over the segment size */
418 #ifdef CONFIG_MMC_CRYPTO
419 #define MMC_CAP2_CRYPTO (1 << 27) /* Host supports inline encryption */
421 #define MMC_CAP2_CRYPTO 0
423 #define MMC_CAP2_ALT_GPT_TEGRA (1 << 28) /* Host with eMMC that has GPT entry at a non-standard location */
425 int fixed_drv_type; /* fixed driver type for non-removable media */
427 mmc_pm_flag_t pm_caps; /* supported pm features */
429 /* host specific block data */
430 unsigned int max_seg_size; /* see blk_queue_max_segment_size */
431 unsigned short max_segs; /* see blk_queue_max_segments */
432 unsigned short unused;
433 unsigned int max_req_size; /* maximum number of bytes in one req */
434 unsigned int max_blk_size; /* maximum size of one mmc block */
435 unsigned int max_blk_count; /* maximum number of blocks in one req */
436 unsigned int max_busy_timeout; /* max busy timeout in ms */
439 spinlock_t lock; /* lock for claim and bus ops */
441 struct mmc_ios ios; /* current io bus settings */
443 /* group bitfields together to minimize padding */
444 unsigned int use_spi_crc:1;
445 unsigned int claimed:1; /* host exclusively claimed */
446 unsigned int doing_init_tune:1; /* initial tuning in progress */
447 unsigned int can_retune:1; /* re-tuning can be used */
448 unsigned int doing_retune:1; /* re-tuning in progress */
449 unsigned int retune_now:1; /* do re-tuning at next req */
450 unsigned int retune_paused:1; /* re-tuning is temporarily disabled */
451 unsigned int retune_crc_disable:1; /* don't trigger retune upon crc */
452 unsigned int can_dma_map_merge:1; /* merging can be used */
454 int rescan_disable; /* disable card detection */
455 int rescan_entered; /* used with nonremovable devices */
457 int need_retune; /* re-tuning is needed */
458 int hold_retune; /* hold off re-tuning */
459 unsigned int retune_period; /* re-tuning period in secs */
460 struct timer_list retune_timer; /* for periodic re-tuning */
462 bool trigger_card_event; /* card_event necessary */
464 struct mmc_card *card; /* device attached to this host */
466 wait_queue_head_t wq;
467 struct mmc_ctx *claimer; /* context that has host claimed */
468 int claim_cnt; /* "claim" nesting count */
469 struct mmc_ctx default_ctx; /* default context */
471 struct delayed_work detect;
472 int detect_change; /* card detect flag */
473 struct mmc_slot slot;
475 const struct mmc_bus_ops *bus_ops; /* current bus driver */
477 unsigned int sdio_irqs;
478 struct task_struct *sdio_irq_thread;
479 struct delayed_work sdio_irq_work;
480 bool sdio_irq_pending;
481 atomic_t sdio_irq_thread_abort;
483 mmc_pm_flag_t pm_flags; /* requested pm features */
485 struct led_trigger *led; /* activity led */
487 #ifdef CONFIG_REGULATOR
488 bool regulator_enabled; /* regulator state */
490 struct mmc_supply supply;
492 struct dentry *debugfs_root;
494 /* Ongoing data transfer that allows commands during transfer */
495 struct mmc_request *ongoing_mrq;
497 #ifdef CONFIG_FAIL_MMC_REQUEST
498 struct fault_attr fail_mmc_request;
501 unsigned int actual_clock; /* Actual HC clock rate */
503 unsigned int slotno; /* used for sdio acpi binding */
505 int dsr_req; /* DSR value is valid */
506 u32 dsr; /* optional driver stage (DSR) value */
508 /* Command Queue Engine (CQE) support */
509 const struct mmc_cqe_ops *cqe_ops;
515 /* Inline encryption support */
516 #ifdef CONFIG_MMC_CRYPTO
517 struct blk_crypto_profile crypto_profile;
520 /* Host Software Queue support */
523 u32 err_stats[MMC_ERR_MAX];
524 unsigned long private[] ____cacheline_aligned;
529 struct mmc_host *mmc_alloc_host(int extra, struct device *);
530 int mmc_add_host(struct mmc_host *);
531 void mmc_remove_host(struct mmc_host *);
532 void mmc_free_host(struct mmc_host *);
533 void mmc_of_parse_clk_phase(struct mmc_host *host,
534 struct mmc_clk_phase_map *map);
535 int mmc_of_parse(struct mmc_host *host);
536 int mmc_of_parse_voltage(struct mmc_host *host, u32 *mask);
538 static inline void *mmc_priv(struct mmc_host *host)
540 return (void *)host->private;
543 static inline struct mmc_host *mmc_from_priv(void *priv)
545 return container_of(priv, struct mmc_host, private);
548 #define mmc_host_is_spi(host) ((host)->caps & MMC_CAP_SPI)
550 #define mmc_dev(x) ((x)->parent)
551 #define mmc_classdev(x) (&(x)->class_dev)
552 #define mmc_hostname(x) (dev_name(&(x)->class_dev))
554 void mmc_detect_change(struct mmc_host *, unsigned long delay);
555 void mmc_request_done(struct mmc_host *, struct mmc_request *);
556 void mmc_command_done(struct mmc_host *host, struct mmc_request *mrq);
558 void mmc_cqe_request_done(struct mmc_host *host, struct mmc_request *mrq);
561 * May be called from host driver's system/runtime suspend/resume callbacks,
562 * to know if SDIO IRQs has been claimed.
564 static inline bool sdio_irq_claimed(struct mmc_host *host)
566 return host->sdio_irqs > 0;
569 static inline void mmc_signal_sdio_irq(struct mmc_host *host)
571 host->ops->enable_sdio_irq(host, 0);
572 host->sdio_irq_pending = true;
573 if (host->sdio_irq_thread)
574 wake_up_process(host->sdio_irq_thread);
577 void sdio_signal_irq(struct mmc_host *host);
579 #ifdef CONFIG_REGULATOR
580 int mmc_regulator_set_ocr(struct mmc_host *mmc,
581 struct regulator *supply,
582 unsigned short vdd_bit);
583 int mmc_regulator_set_vqmmc(struct mmc_host *mmc, struct mmc_ios *ios);
585 static inline int mmc_regulator_set_ocr(struct mmc_host *mmc,
586 struct regulator *supply,
587 unsigned short vdd_bit)
592 static inline int mmc_regulator_set_vqmmc(struct mmc_host *mmc,
599 int mmc_regulator_get_supply(struct mmc_host *mmc);
601 static inline int mmc_card_is_removable(struct mmc_host *host)
603 return !(host->caps & MMC_CAP_NONREMOVABLE);
606 static inline int mmc_card_keep_power(struct mmc_host *host)
608 return host->pm_flags & MMC_PM_KEEP_POWER;
611 static inline int mmc_card_wake_sdio_irq(struct mmc_host *host)
613 return host->pm_flags & MMC_PM_WAKE_SDIO_IRQ;
616 /* TODO: Move to private header */
617 static inline int mmc_card_hs(struct mmc_card *card)
619 return card->host->ios.timing == MMC_TIMING_SD_HS ||
620 card->host->ios.timing == MMC_TIMING_MMC_HS;
623 /* TODO: Move to private header */
624 static inline int mmc_card_uhs(struct mmc_card *card)
626 return card->host->ios.timing >= MMC_TIMING_UHS_SDR12 &&
627 card->host->ios.timing <= MMC_TIMING_UHS_DDR50;
630 void mmc_retune_timer_stop(struct mmc_host *host);
632 static inline void mmc_retune_needed(struct mmc_host *host)
634 if (host->can_retune)
635 host->need_retune = 1;
638 static inline bool mmc_can_retune(struct mmc_host *host)
640 return host->can_retune == 1;
643 static inline bool mmc_doing_retune(struct mmc_host *host)
645 return host->doing_retune == 1;
648 static inline bool mmc_doing_tune(struct mmc_host *host)
650 return host->doing_retune == 1 || host->doing_init_tune == 1;
653 static inline enum dma_data_direction mmc_get_dma_dir(struct mmc_data *data)
655 return data->flags & MMC_DATA_WRITE ? DMA_TO_DEVICE : DMA_FROM_DEVICE;
658 static inline void mmc_debugfs_err_stats_inc(struct mmc_host *host,
659 enum mmc_err_stat stat)
661 host->err_stats[stat] += 1;
664 int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
665 int mmc_send_abort_tuning(struct mmc_host *host, u32 opcode);
666 int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd);
668 #endif /* LINUX_MMC_HOST_H */