2 * Copyright 2008 Freescale Semiconductor, Inc.
4 * This program is free software; you can redistribute it and/or
5 * modify it under the terms of the GNU General Public License
6 * Version 2 as published by the Free Software Foundation.
13 * Format from "JEDEC Standard No. 21-C,
14 * Appendix D: Rev 1.0: SPD's for DDR SDRAM
16 typedef struct ddr1_spd_eeprom_s {
17 unsigned char info_size; /* 0 # bytes written into serial memory */
18 unsigned char chip_size; /* 1 Total # bytes of SPD memory device */
19 unsigned char mem_type; /* 2 Fundamental memory type */
20 unsigned char nrow_addr; /* 3 # of Row Addresses on this assembly */
21 unsigned char ncol_addr; /* 4 # of Column Addrs on this assembly */
22 unsigned char nrows; /* 5 Number of DIMM Banks */
23 unsigned char dataw_lsb; /* 6 Data Width of this assembly */
24 unsigned char dataw_msb; /* 7 ... Data Width continuation */
25 unsigned char voltage; /* 8 Voltage intf std of this assembly */
26 unsigned char clk_cycle; /* 9 SDRAM Cycle time @ CL=X */
27 unsigned char clk_access; /* 10 SDRAM Access from Clk @ CL=X (tAC) */
28 unsigned char config; /* 11 DIMM Configuration type */
29 unsigned char refresh; /* 12 Refresh Rate/Type */
30 unsigned char primw; /* 13 Primary SDRAM Width */
31 unsigned char ecw; /* 14 Error Checking SDRAM width */
32 unsigned char min_delay; /* 15 for Back to Back Random Address */
33 unsigned char burstl; /* 16 Burst Lengths Supported */
34 unsigned char nbanks; /* 17 # of Banks on SDRAM Device */
35 unsigned char cas_lat; /* 18 CAS# Latencies Supported */
36 unsigned char cs_lat; /* 19 CS# Latency */
37 unsigned char write_lat; /* 20 Write Latency (aka Write Recovery) */
38 unsigned char mod_attr; /* 21 SDRAM Module Attributes */
39 unsigned char dev_attr; /* 22 SDRAM Device Attributes */
40 unsigned char clk_cycle2; /* 23 Min SDRAM Cycle time @ CL=X-0.5 */
41 unsigned char clk_access2; /* 24 SDRAM Access from
42 Clk @ CL=X-0.5 (tAC) */
43 unsigned char clk_cycle3; /* 25 Min SDRAM Cycle time @ CL=X-1 */
44 unsigned char clk_access3; /* 26 Max Access from Clk @ CL=X-1 (tAC) */
45 unsigned char trp; /* 27 Min Row Precharge Time (tRP)*/
46 unsigned char trrd; /* 28 Min Row Active to Row Active (tRRD) */
47 unsigned char trcd; /* 29 Min RAS to CAS Delay (tRCD) */
48 unsigned char tras; /* 30 Minimum RAS Pulse Width (tRAS) */
49 unsigned char bank_dens; /* 31 Density of each bank on module */
50 unsigned char ca_setup; /* 32 Addr + Cmd Setup Time Before Clk */
51 unsigned char ca_hold; /* 33 Addr + Cmd Hold Time After Clk */
52 unsigned char data_setup; /* 34 Data Input Setup Time Before Strobe */
53 unsigned char data_hold; /* 35 Data Input Hold Time After Strobe */
54 unsigned char res_36_40[5];/* 36-40 reserved for VCSDRAM */
55 unsigned char trc; /* 41 Min Active to Auto refresh time tRC */
56 unsigned char trfc; /* 42 Min Auto to Active period tRFC */
57 unsigned char tckmax; /* 43 Max device cycle time tCKmax */
58 unsigned char tdqsq; /* 44 Max DQS to DQ skew (tDQSQ max) */
59 unsigned char tqhs; /* 45 Max Read DataHold skew (tQHS) */
60 unsigned char res_46; /* 46 Reserved */
61 unsigned char dimm_height; /* 47 DDR SDRAM DIMM Height */
62 unsigned char res_48_61[14]; /* 48-61 Reserved */
63 unsigned char spd_rev; /* 62 SPD Data Revision Code */
64 unsigned char cksum; /* 63 Checksum for bytes 0-62 */
65 unsigned char mid[8]; /* 64-71 Mfr's JEDEC ID code per JEP-106 */
66 unsigned char mloc; /* 72 Manufacturing Location */
67 unsigned char mpart[18]; /* 73 Manufacturer's Part Number */
68 unsigned char rev[2]; /* 91 Revision Code */
69 unsigned char mdate[2]; /* 93 Manufacturing Date */
70 unsigned char sernum[4]; /* 95 Assembly Serial Number */
71 unsigned char mspec[27]; /* 99-127 Manufacturer Specific Data */
76 * Format from "JEDEC Appendix X: Serial Presence Detects for DDR2 SDRAM",
79 typedef struct ddr2_spd_eeprom_s {
80 unsigned char info_size; /* 0 # bytes written into serial memory */
81 unsigned char chip_size; /* 1 Total # bytes of SPD memory device */
82 unsigned char mem_type; /* 2 Fundamental memory type */
83 unsigned char nrow_addr; /* 3 # of Row Addresses on this assembly */
84 unsigned char ncol_addr; /* 4 # of Column Addrs on this assembly */
85 unsigned char mod_ranks; /* 5 Number of DIMM Ranks */
86 unsigned char dataw; /* 6 Module Data Width */
87 unsigned char res_7; /* 7 Reserved */
88 unsigned char voltage; /* 8 Voltage intf std of this assembly */
89 unsigned char clk_cycle; /* 9 SDRAM Cycle time @ CL=X */
90 unsigned char clk_access; /* 10 SDRAM Access from Clk @ CL=X (tAC) */
91 unsigned char config; /* 11 DIMM Configuration type */
92 unsigned char refresh; /* 12 Refresh Rate/Type */
93 unsigned char primw; /* 13 Primary SDRAM Width */
94 unsigned char ecw; /* 14 Error Checking SDRAM width */
95 unsigned char res_15; /* 15 Reserved */
96 unsigned char burstl; /* 16 Burst Lengths Supported */
97 unsigned char nbanks; /* 17 # of Banks on Each SDRAM Device */
98 unsigned char cas_lat; /* 18 CAS# Latencies Supported */
99 unsigned char mech_char; /* 19 DIMM Mechanical Characteristics */
100 unsigned char dimm_type; /* 20 DIMM type information */
101 unsigned char mod_attr; /* 21 SDRAM Module Attributes */
102 unsigned char dev_attr; /* 22 SDRAM Device Attributes */
103 unsigned char clk_cycle2; /* 23 Min SDRAM Cycle time @ CL=X-1 */
104 unsigned char clk_access2; /* 24 SDRAM Access from Clk @ CL=X-1 (tAC) */
105 unsigned char clk_cycle3; /* 25 Min SDRAM Cycle time @ CL=X-2 */
106 unsigned char clk_access3; /* 26 Max Access from Clk @ CL=X-2 (tAC) */
107 unsigned char trp; /* 27 Min Row Precharge Time (tRP)*/
108 unsigned char trrd; /* 28 Min Row Active to Row Active (tRRD) */
109 unsigned char trcd; /* 29 Min RAS to CAS Delay (tRCD) */
110 unsigned char tras; /* 30 Minimum RAS Pulse Width (tRAS) */
111 unsigned char rank_dens; /* 31 Density of each rank on module */
112 unsigned char ca_setup; /* 32 Addr+Cmd Setup Time Before Clk (tIS) */
113 unsigned char ca_hold; /* 33 Addr+Cmd Hold Time After Clk (tIH) */
114 unsigned char data_setup; /* 34 Data Input Setup Time
115 Before Strobe (tDS) */
116 unsigned char data_hold; /* 35 Data Input Hold Time
117 After Strobe (tDH) */
118 unsigned char twr; /* 36 Write Recovery time tWR */
119 unsigned char twtr; /* 37 Int write to read delay tWTR */
120 unsigned char trtp; /* 38 Int read to precharge delay tRTP */
121 unsigned char mem_probe; /* 39 Mem analysis probe characteristics */
122 unsigned char trctrfc_ext; /* 40 Extensions to trc and trfc */
123 unsigned char trc; /* 41 Min Active to Auto refresh time tRC */
124 unsigned char trfc; /* 42 Min Auto to Active period tRFC */
125 unsigned char tckmax; /* 43 Max device cycle time tCKmax */
126 unsigned char tdqsq; /* 44 Max DQS to DQ skew (tDQSQ max) */
127 unsigned char tqhs; /* 45 Max Read DataHold skew (tQHS) */
128 unsigned char pll_relock; /* 46 PLL Relock time */
129 unsigned char Tcasemax; /* 47 Tcasemax */
130 unsigned char psiTAdram; /* 48 Thermal Resistance of DRAM Package from
131 Top (Case) to Ambient (Psi T-A DRAM) */
132 unsigned char dt0_mode; /* 49 DRAM Case Temperature Rise from Ambient
133 due to Activate-Precharge/Mode Bits
135 unsigned char dt2n_dt2q; /* 50 DRAM Case Temperature Rise from Ambient
136 due to Precharge/Quiet Standby
138 unsigned char dt2p; /* 51 DRAM Case Temperature Rise from Ambient
139 due to Precharge Power-Down (DT2P) */
140 unsigned char dt3n; /* 52 DRAM Case Temperature Rise from Ambient
141 due to Active Standby (DT3N) */
142 unsigned char dt3pfast; /* 53 DRAM Case Temperature Rise from Ambient
143 due to Active Power-Down with
144 Fast PDN Exit (DT3Pfast) */
145 unsigned char dt3pslow; /* 54 DRAM Case Temperature Rise from Ambient
146 due to Active Power-Down with Slow
147 PDN Exit (DT3Pslow) */
148 unsigned char dt4r_dt4r4w; /* 55 DRAM Case Temperature Rise from Ambient
149 due to Page Open Burst Read/DT4R4W
150 Mode Bit (DT4R/DT4R4W Mode Bit) */
151 unsigned char dt5b; /* 56 DRAM Case Temperature Rise from Ambient
152 due to Burst Refresh (DT5B) */
153 unsigned char dt7; /* 57 DRAM Case Temperature Rise from Ambient
154 due to Bank Interleave Reads with
155 Auto-Precharge (DT7) */
156 unsigned char psiTApll; /* 58 Thermal Resistance of PLL Package form
157 Top (Case) to Ambient (Psi T-A PLL) */
158 unsigned char psiTAreg; /* 59 Thermal Reisitance of Register Package
159 from Top (Case) to Ambient
160 (Psi T-A Register) */
161 unsigned char dtpllactive; /* 60 PLL Case Temperature Rise from Ambient
162 due to PLL Active (DT PLL Active) */
163 unsigned char dtregact; /* 61 Register Case Temperature Rise from
164 Ambient due to Register Active/Mode Bit
165 (DT Register Active/Mode Bit) */
166 unsigned char spd_rev; /* 62 SPD Data Revision Code */
167 unsigned char cksum; /* 63 Checksum for bytes 0-62 */
168 unsigned char mid[8]; /* 64 Mfr's JEDEC ID code per JEP-106 */
169 unsigned char mloc; /* 72 Manufacturing Location */
170 unsigned char mpart[18]; /* 73 Manufacturer's Part Number */
171 unsigned char rev[2]; /* 91 Revision Code */
172 unsigned char mdate[2]; /* 93 Manufacturing Date */
173 unsigned char sernum[4]; /* 95 Assembly Serial Number */
174 unsigned char mspec[27]; /* 99-127 Manufacturer Specific Data */
178 typedef struct ddr3_spd_eeprom_s {
179 /* General Section: Bytes 0-59 */
180 unsigned char info_size_crc; /* 0 # bytes written into serial memory,
182 unsigned char spd_rev; /* 1 Total # bytes of SPD mem device */
183 unsigned char mem_type; /* 2 Key Byte / Fundamental mem type */
184 unsigned char module_type; /* 3 Key Byte / Module Type */
185 unsigned char density_banks; /* 4 SDRAM Density and Banks */
186 unsigned char addressing; /* 5 SDRAM Addressing */
187 unsigned char res_6; /* 6 Reserved */
188 unsigned char organization; /* 7 Module Organization */
189 unsigned char bus_width; /* 8 Module Memory Bus Width */
190 unsigned char ftb_div; /* 9 Fine Timebase (FTB)
191 Dividend / Divisor */
192 unsigned char mtb_dividend; /* 10 Medium Timebase (MTB) Dividend */
193 unsigned char mtb_divisor; /* 11 Medium Timebase (MTB) Divisor */
194 unsigned char tCK_min; /* 12 SDRAM Minimum Cycle Time */
195 unsigned char res_13; /* 13 Reserved */
196 unsigned char caslat_lsb; /* 14 CAS Latencies Supported,
197 Least Significant Byte */
198 unsigned char caslat_msb; /* 15 CAS Latencies Supported,
199 Most Significant Byte */
200 unsigned char tAA_min; /* 16 Min CAS Latency Time */
201 unsigned char tWR_min; /* 17 Min Write REcovery Time */
202 unsigned char tRCD_min; /* 18 Min RAS# to CAS# Delay Time */
203 unsigned char tRRD_min; /* 19 Min Row Active to
204 Row Active Delay Time */
205 unsigned char tRP_min; /* 20 Min Row Precharge Delay Time */
206 unsigned char tRAS_tRC_ext; /* 21 Upper Nibbles for tRAS and tRC */
207 unsigned char tRAS_min_lsb; /* 22 Min Active to Precharge
209 unsigned char tRC_min_lsb; /* 23 Min Active to Active/Refresh
211 unsigned char tRFC_min_lsb; /* 24 Min Refresh Recovery Delay Time */
212 unsigned char tRFC_min_msb; /* 25 Min Refresh Recovery Delay Time */
213 unsigned char tWTR_min; /* 26 Min Internal Write to
214 Read Command Delay Time */
215 unsigned char tRTP_min; /* 27 Min Internal Read to Precharge
216 Command Delay Time */
217 unsigned char tFAW_msb; /* 28 Upper Nibble for tFAW */
218 unsigned char tFAW_min; /* 29 Min Four Activate Window
220 unsigned char opt_features; /* 30 SDRAM Optional Features */
221 unsigned char therm_ref_opt; /* 31 SDRAM Thermal and Refresh Opts */
222 unsigned char res_32_59[28]; /* 32-59 Reserved, General Section */
224 /* Module-Specific Section: Bytes 60-116 */
227 /* 60 (Unbuffered) Module Nominal Height */
228 unsigned char mod_height;
229 /* 61 (Unbuffered) Module Maximum Thickness */
230 unsigned char mod_thickness;
231 /* 62 (Unbuffered) Reference Raw Card Used */
232 unsigned char ref_raw_card;
233 /* 63 (Unbuffered) Address Mapping from
234 Edge Connector to DRAM */
235 unsigned char addr_mapping;
236 /* 64-116 (Unbuffered) Reserved */
237 unsigned char res_64_116[53];
240 /* 60 (Registered) Module Nominal Height */
241 unsigned char mod_height;
242 /* 61 (Registered) Module Maximum Thickness */
243 unsigned char mod_thickness;
244 /* 62 (Registered) Reference Raw Card Used */
245 unsigned char ref_raw_card;
247 unsigned char uc[57]; /* 60-116 Module-Specific Section */
250 /* Unique Module ID: Bytes 117-125 */
251 unsigned char mmid_lsb; /* 117 Module MfgID Code LSB - JEP-106 */
252 unsigned char mmid_msb; /* 118 Module MfgID Code MSB - JEP-106 */
253 unsigned char mloc; /* 119 Mfg Location */
254 unsigned char mdate[2]; /* 120-121 Mfg Date */
255 unsigned char sernum[4]; /* 122-125 Module Serial Number */
257 /* CRC: Bytes 126-127 */
258 unsigned char crc[2]; /* 126-127 SPD CRC */
260 /* Other Manufacturer Fields and User Space: Bytes 128-255 */
261 unsigned char mpart[18]; /* 128-145 Mfg's Module Part Number */
262 unsigned char mrev[2]; /* 146-147 Module Revision Code */
264 unsigned char dmid_lsb; /* 148 DRAM MfgID Code LSB - JEP-106 */
265 unsigned char dmid_msb; /* 149 DRAM MfgID Code MSB - JEP-106 */
267 unsigned char msd[26]; /* 150-175 Mfg's Specific Data */
268 unsigned char cust[80]; /* 176-255 Open for Customer Use */
272 extern unsigned int ddr1_spd_check(const ddr1_spd_eeprom_t *spd);
273 extern void ddr1_spd_dump(const ddr1_spd_eeprom_t *spd);
274 extern unsigned int ddr2_spd_check(const ddr2_spd_eeprom_t *spd);
275 extern void ddr2_spd_dump(const ddr2_spd_eeprom_t *spd);
278 * Byte 2 Fundamental Memory Types.
280 #define SPD_MEMTYPE_FPM (0x01)
281 #define SPD_MEMTYPE_EDO (0x02)
282 #define SPD_MEMTYPE_PIPE_NIBBLE (0x03)
283 #define SPD_MEMTYPE_SDRAM (0x04)
284 #define SPD_MEMTYPE_ROM (0x05)
285 #define SPD_MEMTYPE_SGRAM (0x06)
286 #define SPD_MEMTYPE_DDR (0x07)
287 #define SPD_MEMTYPE_DDR2 (0x08)
288 #define SPD_MEMTYPE_DDR2_FBDIMM (0x09)
289 #define SPD_MEMTYPE_DDR2_FBDIMM_PROBE (0x0A)
290 #define SPD_MEMTYPE_DDR3 (0x0B)
292 #endif /* _DDR_SPD_H_ */