include/configs/zynq-common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * (C) Copyright 2012 Michal Simek <monstr@monstr.eu>
   4  * (C) Copyright 2013 - 2018 Xilinx, Inc.
   5  *
   6  * Common configuration options for all Zynq boards.
   7  */
   8
   9 #ifndef __CONFIG_ZYNQ_COMMON_H
  10 #define __CONFIG_ZYNQ_COMMON_H
  11
  12 /* CPU clock */
  13 #ifndef CONFIG_CPU_FREQ_HZ
  14 # define CONFIG_CPU_FREQ_HZ     800000000
  15 #endif
  16
  17 /* Cache options */
  18 #define CONFIG_SYS_L2CACHE_OFF
  19 #ifndef CONFIG_SYS_L2CACHE_OFF
  20 # define CONFIG_SYS_L2_PL310
  21 # define CONFIG_SYS_PL310_BASE          0xf8f02000
  22 #endif
  23
  24 #define ZYNQ_SCUTIMER_BASEADDR          0xF8F00600
  25 #define CONFIG_SYS_TIMERBASE            ZYNQ_SCUTIMER_BASEADDR
  26 #define CONFIG_SYS_TIMER_COUNTS_DOWN
  27 #define CONFIG_SYS_TIMER_COUNTER        (CONFIG_SYS_TIMERBASE + 0x4)
  28
  29 /* Serial drivers */
  30 /* The following table includes the supported baudrates */
  31 #define CONFIG_SYS_BAUDRATE_TABLE  \
  32         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
  33
  34 #define CONFIG_ARM_DCC
  35
  36 /* Ethernet driver */
  37 #if defined(CONFIG_ZYNQ_GEM)
  38 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  39 # define CONFIG_BOOTP_MAY_FAIL
  40 #endif
  41
  42 /* QSPI */
  43 #ifdef CONFIG_ZYNQ_QSPI
  44 # define CONFIG_SF_DEFAULT_SPEED        30000000
  45 #endif
  46
  47 /* NOR */
  48 #ifdef CONFIG_MTD_NOR_FLASH
  49 # define CONFIG_SYS_FLASH_BASE          0xE2000000
  50 # define CONFIG_SYS_FLASH_SIZE          (16 * 1024 * 1024)
  51 # define CONFIG_SYS_MAX_FLASH_BANKS     1
  52 # define CONFIG_SYS_MAX_FLASH_SECT      512
  53 # define CONFIG_SYS_FLASH_ERASE_TOUT    1000
  54 # define CONFIG_SYS_FLASH_WRITE_TOUT    5000
  55 # define CONFIG_FLASH_SHOW_PROGRESS     10
  56 # define CONFIG_SYS_FLASH_CFI
  57 # undef CONFIG_SYS_FLASH_EMPTY_INFO
  58 # define CONFIG_FLASH_CFI_DRIVER
  59 # undef CONFIG_SYS_FLASH_PROTECTION
  60 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
  61 #endif
  62
  63 #ifdef CONFIG_NAND_ZYNQ
  64 #define CONFIG_SYS_MAX_NAND_DEVICE      1
  65 #define CONFIG_SYS_NAND_ONFI_DETECTION
  66 #endif
  67
  68 #ifdef CONFIG_USB_EHCI_ZYNQ
  69 # define CONFIG_EHCI_IS_TDI
  70
  71 # define CONFIG_SYS_DFU_DATA_BUF_SIZE   0x600000
  72 # define DFU_DEFAULT_POLL_TIMEOUT       300
  73 # define CONFIG_USB_CABLE_CHECK
  74 # define CONFIG_THOR_RESET_OFF
  75 # define DFU_ALT_INFO_RAM \
  76         "dfu_ram_info=" \
  77         "set dfu_alt_info " \
  78         "${kernel_image} ram 0x3000000 0x500000\\\\;" \
  79         "${devicetree_image} ram 0x2A00000 0x20000\\\\;" \
  80         "${ramdisk_image} ram 0x2000000 0x600000\0" \
  81         "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
  82         "thor_ram=run dfu_ram_info && thordown 0 ram 0\0"
  83
  84 # if defined(CONFIG_MMC_SDHCI_ZYNQ)
  85 #  define DFU_ALT_INFO_MMC \
  86         "dfu_mmc_info=" \
  87         "set dfu_alt_info " \
  88         "${kernel_image} fat 0 1\\\\;" \
  89         "${devicetree_image} fat 0 1\\\\;" \
  90         "${ramdisk_image} fat 0 1\0" \
  91         "dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \
  92         "thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0"
  93
  94 #  define DFU_ALT_INFO  \
  95         DFU_ALT_INFO_RAM \
  96         DFU_ALT_INFO_MMC
  97 # else
  98 #  define DFU_ALT_INFO  \
  99         DFU_ALT_INFO_RAM
 100 # endif
 101 #endif
 102
 103 #if !defined(DFU_ALT_INFO)
 104 # define DFU_ALT_INFO
 105 #endif
 106
 107 /* I2C */
 108 #if defined(CONFIG_SYS_I2C_ZYNQ)
 109 # define CONFIG_SYS_I2C
 110 #endif
 111
 112 /* EEPROM */
 113 #ifdef CONFIG_ZYNQ_EEPROM
 114 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
 115 # define CONFIG_SYS_I2C_EEPROM_ADDR             0x54
 116 # define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      4
 117 # define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  5
 118 # define CONFIG_SYS_EEPROM_SIZE                 1024 /* Bytes */
 119 #endif
 120
 121 /* Allow to overwrite serial and ethaddr */
 122 #define CONFIG_ENV_OVERWRITE
 123
 124 /* enable preboot to be loaded before CONFIG_BOOTDELAY */
 125 #define CONFIG_PREBOOT
 126
 127 /* Boot configuration */
 128 #define CONFIG_SYS_LOAD_ADDR            0 /* default? */
 129
 130 #ifdef CONFIG_SPL_BUILD
 131 #define BOOTENV
 132 #else
 133
 134 #ifdef CONFIG_CMD_MMC
 135 #define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
 136 #else
 137 #define BOOT_TARGET_DEVICES_MMC(func)
 138 #endif
 139
 140 #ifdef CONFIG_CMD_USB
 141 #define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
 142 #else
 143 #define BOOT_TARGET_DEVICES_USB(func)
 144 #endif
 145
 146 #if defined(CONFIG_CMD_PXE) && defined(CONFIG_CMD_DHCP)
 147 #define BOOT_TARGET_DEVICES_PXE(func) func(PXE, pxe, na)
 148 #else
 149 #define BOOT_TARGET_DEVICES_PXE(func)
 150 #endif
 151
 152 #if defined(CONFIG_CMD_DHCP)
 153 #define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
 154 #else
 155 #define BOOT_TARGET_DEVICES_DHCP(func)
 156 #endif
 157
 158 #define BOOT_TARGET_DEVICES(func) \
 159         BOOT_TARGET_DEVICES_MMC(func) \
 160         BOOT_TARGET_DEVICES_USB(func) \
 161         BOOT_TARGET_DEVICES_PXE(func) \
 162         BOOT_TARGET_DEVICES_DHCP(func)
 163
 164 #include <config_distro_bootcmd.h>
 165 #endif /* CONFIG_SPL_BUILD */
 166
 167 /* Default environment */
 168 #ifndef CONFIG_EXTRA_ENV_SETTINGS
 169 #define CONFIG_EXTRA_ENV_SETTINGS       \
 170         "fit_image=fit.itb\0"           \
 171         "load_addr=0x2000000\0"         \
 172         "fit_size=0x800000\0"           \
 173         "flash_off=0x100000\0"          \
 174         "nor_flash_off=0xE2100000\0"    \
 175         "fdt_high=0x20000000\0"         \
 176         "initrd_high=0x20000000\0"      \
 177         "loadbootenv_addr=0x2000000\0" \
 178         "fdt_addr_r=0x1f00000\0"        \
 179         "pxefile_addr_r=0x2000000\0"    \
 180         "kernel_addr_r=0x2000000\0"     \
 181         "scriptaddr=0x3000000\0"        \
 182         "ramdisk_addr_r=0x3100000\0"    \
 183         "bootenv=uEnv.txt\0" \
 184         "bootenv_dev=mmc\0" \
 185         "loadbootenv=load ${bootenv_dev} 0 ${loadbootenv_addr} ${bootenv}\0" \
 186         "importbootenv=echo Importing environment from ${bootenv_dev} ...; " \
 187                 "env import -t ${loadbootenv_addr} $filesize\0" \
 188         "bootenv_existence_test=test -e ${bootenv_dev} 0 /${bootenv}\0" \
 189         "setbootenv=if env run bootenv_existence_test; then " \
 190                         "if env run loadbootenv; then " \
 191                                 "env run importbootenv; " \
 192                         "fi; " \
 193                 "fi; \0" \
 194         "sd_loadbootenv=set bootenv_dev mmc && " \
 195                         "run setbootenv \0" \
 196         "usb_loadbootenv=set bootenv_dev usb && usb start && run setbootenv \0" \
 197         "preboot=if test $modeboot = sdboot; then " \
 198                         "run sd_loadbootenv; " \
 199                         "echo Checking if uenvcmd is set ...; " \
 200                         "if test -n $uenvcmd; then " \
 201                                 "echo Running uenvcmd ...; " \
 202                                 "run uenvcmd; " \
 203                         "fi; " \
 204                 "fi; \0" \
 205         "norboot=echo Copying FIT from NOR flash to RAM... && " \
 206                 "cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \
 207                 "bootm ${load_addr}\0" \
 208         "sdboot=echo Copying FIT from SD to RAM... && " \
 209                 "load mmc 0 ${load_addr} ${fit_image} && " \
 210                 "bootm ${load_addr}\0" \
 211         "jtagboot=echo TFTPing FIT to RAM... && " \
 212                 "tftpboot ${load_addr} ${fit_image} && " \
 213                 "bootm ${load_addr}\0" \
 214         "usbboot=if usb start; then " \
 215                         "echo Copying FIT from USB to RAM... && " \
 216                         "load usb 0 ${load_addr} ${fit_image} && " \
 217                         "bootm ${load_addr}; fi\0" \
 218                 DFU_ALT_INFO \
 219                 BOOTENV
 220 #endif
 221
 222 /* Miscellaneous configurable options */
 223
 224 #define CONFIG_CLOCKS
 225 #define CONFIG_SYS_MAXARGS              32 /* max number of command args */
 226
 227 #define CONFIG_SYS_MEMTEST_START        0
 228 #define CONFIG_SYS_MEMTEST_END          0x1000
 229
 230 #define CONFIG_SYS_INIT_RAM_ADDR        0xFFFF0000
 231 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000
 232 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_INIT_RAM_ADDR + \
 233                                         CONFIG_SYS_INIT_RAM_SIZE - \
 234                                         GENERATED_GBL_DATA_SIZE)
 235
 236
 237 /* Extend size of kernel image for uncompression */
 238 #define CONFIG_SYS_BOOTM_LEN    (60 * 1024 * 1024)
 239
 240 /* Boot FreeBSD/vxWorks from an ELF image */
 241 #define CONFIG_SYS_MMC_MAX_DEVICE       1
 242
 243 #define CONFIG_SYS_LDSCRIPT  "arch/arm/mach-zynq/u-boot.lds"
 244
 245 /* MMC support */
 246 #ifdef CONFIG_MMC_SDHCI_ZYNQ
 247 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
 248 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot.img"
 249 #endif
 250
 251 /* Disable dcache for SPL just for sure */
 252 #ifdef CONFIG_SPL_BUILD
 253 #define CONFIG_SYS_DCACHE_OFF
 254 #endif
 255
 256 /* Address in RAM where the parameters must be copied by SPL. */
 257 #define CONFIG_SYS_SPL_ARGS_ADDR        0x10000000
 258
 259 #define CONFIG_SPL_FS_LOAD_ARGS_NAME            "system.dtb"
 260 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME          "uImage"
 261
 262 /* Not using MMC raw mode - just for compilation purpose */
 263 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR   0
 264 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS  0
 265 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0
 266
 267 /* qspi mode is working fine */
 268 #ifdef CONFIG_ZYNQ_QSPI
 269 #define CONFIG_SYS_SPI_U_BOOT_OFFS      0x100000
 270 #define CONFIG_SYS_SPI_ARGS_OFFS        0x200000
 271 #define CONFIG_SYS_SPI_ARGS_SIZE        0x80000
 272 #define CONFIG_SYS_SPI_KERNEL_OFFS      (CONFIG_SYS_SPI_ARGS_OFFS + \
 273                                         CONFIG_SYS_SPI_ARGS_SIZE)
 274 #endif
 275
 276 /* SP location before relocation, must use scratch RAM */
 277 #define CONFIG_SPL_TEXT_BASE    0x0
 278
 279 /* 3 * 64kB blocks of OCM - one is on the top because of bootrom */
 280 #define CONFIG_SPL_MAX_SIZE     0x30000
 281
 282 /* On the top of OCM space */
 283 #define CONFIG_SYS_SPL_MALLOC_START     CONFIG_SPL_STACK_R_ADDR
 284 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x2000000
 285
 286 /*
 287  * SPL stack position - and stack goes down
 288  * 0xfffffe00 is used for putting wfi loop.
 289  * Set it up as limit for now.
 290  */
 291 #define CONFIG_SPL_STACK        0xfffffe00
 292
 293 /* BSS setup */
 294 #define CONFIG_SPL_BSS_START_ADDR       0x100000
 295 #define CONFIG_SPL_BSS_MAX_SIZE         0x100000
 296
 297 #define CONFIG_SYS_UBOOT_START  CONFIG_SYS_TEXT_BASE
 298
 299 #endif /* __CONFIG_ZYNQ_COMMON_H */