include/configs/xpedite550x.h

   1 /*
   2  * Copyright 2010 Extreme Engineering Solutions, Inc.
   3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * xpedite550x board configuration file
  10  */
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * High Level Configuration Options
  16  */
  17 #define CONFIG_XPEDITE550X      1
  18 #define CONFIG_SYS_BOARD_NAME   "XPedite5500"
  19 #define CONFIG_SYS_FORM_PMC_XMC 1
  20 #define CONFIG_PRPMC_PCI_ALIAS  "pci0"  /* Processor PMC interface on pci0 */
  21 #define CONFIG_BOARD_EARLY_INIT_R       /* Call board_pre_init */
  22
  23 #ifndef CONFIG_SYS_TEXT_BASE
  24 #define CONFIG_SYS_TEXT_BASE    0xfff80000
  25 #endif
  26
  27 #define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup */
  28 #define CONFIG_PCIE1            1       /* PCIE controller 1 (PEX8112 or XMC) */
  29 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  30 #define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
  31 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  32 #define CONFIG_FSL_PCIE_RESET   1       /* need PCIe reset errata */
  33 #define CONFIG_FSL_ELBC         1
  34
  35 /*
  36  * Multicore config
  37  */
  38 #define CONFIG_MP
  39 #define CONFIG_BPTR_VIRT_ADDR   0xee000000      /* virt boot page address */
  40 #define CONFIG_MPC8xxx_DISABLE_BPTR             /* Don't leave BPTR enabled */
  41
  42 /*
  43  * DDR config
  44  */
  45 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
  46 #define CONFIG_DDR_SPD
  47 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  48 #define SPD_EEPROM_ADDRESS                      0x54
  49 #define SPD_EEPROM_OFFSET               0x200   /* OFFSET of SPD in EEPROM */
  50 #define CONFIG_NUM_DDR_CONTROLLERS      1
  51 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  52 #define CONFIG_CHIP_SELECTS_PER_CTRL 2
  53 #define CONFIG_DDR_ECC
  54 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  55 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000 /* DDR is system memory*/
  56 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  57 #define CONFIG_VERY_BIG_RAM
  58
  59 #ifndef __ASSEMBLY__
  60 extern unsigned long get_board_sys_clk(unsigned long dummy);
  61 extern unsigned long get_board_ddr_clk(unsigned long dummy);
  62 #endif
  63
  64 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0) /* sysclk for MPC85xx */
  65 #define CONFIG_DDR_CLK_FREQ     get_board_ddr_clk(0) /* ddrclk for MPC85xx */
  66
  67 /*
  68  * These can be toggled for performance analysis, otherwise use default.
  69  */
  70 #define CONFIG_L2_CACHE                 /* toggle L2 cache */
  71 #define CONFIG_BTB                      /* toggle branch predition */
  72 #define CONFIG_ENABLE_36BIT_PHYS        1
  73
  74 #define CONFIG_SYS_CCSRBAR              0xef000000
  75 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  76
  77 /*
  78  * Diagnostics
  79  */
  80 #define CONFIG_SYS_ALT_MEMTEST
  81 #define CONFIG_SYS_MEMTEST_START        0x10000000
  82 #define CONFIG_SYS_MEMTEST_END          0x20000000
  83 #define CONFIG_POST                     (CONFIG_SYS_POST_MEMORY | \
  84                                          CONFIG_SYS_POST_I2C)
  85 #define I2C_ADDR_LIST                   {CONFIG_SYS_I2C_EEPROM_ADDR,    \
  86                                          CONFIG_SYS_I2C_LM75_ADDR,      \
  87                                          CONFIG_SYS_I2C_LM90_ADDR,      \
  88                                          CONFIG_SYS_I2C_PCA953X_ADDR0,  \
  89                                          CONFIG_SYS_I2C_PCA953X_ADDR2,  \
  90                                          CONFIG_SYS_I2C_PCA953X_ADDR3,  \
  91                                          CONFIG_SYS_I2C_RTC_ADDR}
  92
  93 /*
  94  * Memory map
  95  * 0x0000_0000 0x7fff_ffff      DDR                     2G Cacheable
  96  * 0x8000_0000 0xbfff_ffff      PCIe1 Mem               1G non-cacheable
  97  * 0xe000_0000 0xe7ff_ffff      SRAM/SSRAM/L1 Cache     128M non-cacheable
  98  * 0xe800_0000 0xe87f_ffff      PCIe1 IO                8M non-cacheable
  99  * 0xee00_0000 0xee00_ffff      Boot page translation   4K non-cacheable
 100  * 0xef00_0000 0xef0f_ffff      CCSR/IMMR               1M non-cacheable
 101  * 0xef80_0000 0xef8f_ffff      NAND Flash              1M non-cacheable
 102  * 0xf000_0000 0xf7ff_ffff      NOR Flash 2             128M non-cacheable
 103  * 0xf800_0000 0xffff_ffff      NOR Flash 1             128M non-cacheable
 104  */
 105
 106 #define CONFIG_SYS_LBC_LCRR     (LCRR_CLKDIV_8 | LCRR_EADC_3)
 107
 108 /*
 109  * NAND flash configuration
 110  */
 111 #define CONFIG_SYS_NAND_BASE            0xef800000
 112 #define CONFIG_SYS_NAND_BASE2           0xef840000 /* Unused at this time */
 113 #define CONFIG_SYS_NAND_BASE_LIST       {CONFIG_SYS_NAND_BASE, \
 114                                          CONFIG_SYS_NAND_BASE2}
 115 #define CONFIG_SYS_MAX_NAND_DEVICE      2
 116 #define CONFIG_NAND_FSL_ELBC
 117
 118 /*
 119  * NOR flash configuration
 120  */
 121 #define CONFIG_SYS_FLASH_BASE           0xf8000000
 122 #define CONFIG_SYS_FLASH_BASE2          0xf0000000
 123 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
 124 #define CONFIG_SYS_MAX_FLASH_BANKS      2               /* number of banks */
 125 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
 126 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Flash Erase Timeout (ms) */
 127 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Flash Write Timeout (ms) */
 128 #define CONFIG_FLASH_CFI_DRIVER
 129 #define CONFIG_SYS_FLASH_CFI
 130 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 131 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST       { {0xfff40000, 0xc0000}, \
 132                                                   {0xf7f40000, 0xc0000} }
 133 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 134
 135 /*
 136  * Chip select configuration
 137  */
 138 /* NOR Flash 0 on CS0 */
 139 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE  | \
 140                                  BR_PS_16               | \
 141                                  BR_V)
 142 #define CONFIG_SYS_OR0_PRELIM   (OR_AM_128MB            | \
 143                                  OR_GPCM_CSNT           | \
 144                                  OR_GPCM_XACS           | \
 145                                  OR_GPCM_ACS_DIV2       | \
 146                                  OR_GPCM_SCY_8          | \
 147                                  OR_GPCM_TRLX           | \
 148                                  OR_GPCM_EHTR           | \
 149                                  OR_GPCM_EAD)
 150
 151 /* NOR Flash 1 on CS1 */
 152 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FLASH_BASE2 | \
 153                                  BR_PS_16               | \
 154                                  BR_V)
 155 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 156
 157 /* NAND flash on CS2 */
 158 #define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_NAND_BASE   | \
 159                                  (2<<BR_DECC_SHIFT)     | \
 160                                  BR_PS_8                | \
 161                                  BR_MS_FCM              | \
 162                                  BR_V)
 163
 164 /* NAND flash on CS2 */
 165 #define CONFIG_SYS_OR2_PRELIM   (OR_AM_256KB    | \
 166                                  OR_FCM_PGS     | \
 167                                  OR_FCM_CSCT    | \
 168                                  OR_FCM_CST     | \
 169                                  OR_FCM_CHT     | \
 170                                  OR_FCM_SCY_1   | \
 171                                  OR_FCM_TRLX    | \
 172                                  OR_FCM_EHTR)
 173
 174 /* NAND flash on CS3 */
 175 #define CONFIG_SYS_BR3_PRELIM   (CONFIG_SYS_NAND_BASE2  | \
 176                                  (2<<BR_DECC_SHIFT)     | \
 177                                  BR_PS_8                | \
 178                                  BR_MS_FCM              | \
 179                                  BR_V)
 180 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 181
 182 /*
 183  * Use L1 as initial stack
 184  */
 185 #define CONFIG_SYS_INIT_RAM_LOCK        1
 186 #define CONFIG_SYS_INIT_RAM_ADDR        0xe0000000
 187 #define CONFIG_SYS_INIT_RAM_SIZE                0x00004000
 188
 189 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 190 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 191
 192 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 KB for Mon */
 193 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc */
 194
 195 /*
 196  * Serial Port
 197  */
 198 #define CONFIG_CONS_INDEX               1
 199 #define CONFIG_SYS_NS16550_SERIAL
 200 #define CONFIG_SYS_NS16550_REG_SIZE     1
 201 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 202 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 203 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 204 #define CONFIG_SYS_BAUDRATE_TABLE       \
 205         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 206 #define CONFIG_BAUDRATE                 115200
 207 #define CONFIG_LOADS_ECHO               1       /* echo on for serial download */
 208 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 209
 210 #define CONFIG_FDT_FIXUP_PCI_IRQ        1
 211
 212 /*
 213  * I2C
 214  */
 215 #define CONFIG_SYS_I2C
 216 #define CONFIG_SYS_I2C_FSL
 217 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 218 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 219 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 220 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 221 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 222 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 223
 224 /* I2C DS7505 temperature sensor */
 225 #define CONFIG_DTT_LM75
 226 #define CONFIG_DTT_SENSORS              { 0 }
 227 #define CONFIG_SYS_I2C_LM75_ADDR        0x48
 228
 229 /* I2C ADT7461 temperature sensor */
 230 #define CONFIG_SYS_I2C_LM90_ADDR        0x4C
 231
 232 /* I2C EEPROM - AT24C128B */
 233 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x54
 234 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
 235 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
 236 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
 237
 238 /* I2C RTC */
 239 #define CONFIG_RTC_M41T11               1
 240 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 241 #define CONFIG_SYS_M41T11_BASE_YEAR     2000
 242
 243 /* GPIO */
 244 #define CONFIG_PCA953X
 245 #define CONFIG_SYS_I2C_PCA953X_ADDR0    0x18
 246 #define CONFIG_SYS_I2C_PCA953X_ADDR1    0x1c
 247 #define CONFIG_SYS_I2C_PCA953X_ADDR2    0x1e
 248 #define CONFIG_SYS_I2C_PCA953X_ADDR3    0x1f
 249 #define CONFIG_SYS_I2C_PCA953X_ADDR     CONFIG_SYS_I2C_PCA953X_ADDR0
 250
 251 /*
 252  * GPIO pin definitions, PU = pulled high, PD = pulled low
 253  */
 254 /* PCA9557 @ 0x18*/
 255 #define CONFIG_SYS_PCA953X_C0_SER0_EN           0x01 /* PU; UART0 enable (1: enabled) */
 256 #define CONFIG_SYS_PCA953X_C0_SER0_MODE         0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */
 257 #define CONFIG_SYS_PCA953X_C0_SER1_EN           0x04 /* PU; UART1 enable (1: enabled) */
 258 #define CONFIG_SYS_PCA953X_C0_SER1_MODE         0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */
 259 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS     0x10 /* PU; Boot flash CS select */
 260 #define CONFIG_SYS_PCA953X_NVM_WP               0x20 /* PU; Write protection (0: disabled, 1: enabled) */
 261
 262 /* PCA9557 @ 0x1e*/
 263 #define CONFIG_SYS_PCA953X_XMC_GA0              0x01 /* PU; */
 264 #define CONFIG_SYS_PCA953X_XMC_GA1              0x02 /* PU; */
 265 #define CONFIG_SYS_PCA953X_XMC_GA2              0x04 /* PU; */
 266 #define CONFIG_SYS_PCA953X_XMC_WAKE             0x10 /* PU; */
 267 #define CONFIG_SYS_PCA953X_XMC_BIST             0x20 /* Enable XMC BIST */
 268 #define CONFIG_SYS_PCA953X_PMC_EREADY           0x40 /* PU; PMC PCI eready */
 269 #define CONFIG_SYS_PCA953X_PMC_MONARCH          0x80 /* PMC monarch mode enable */
 270
 271 /* PCA9557 @ 0x1f */
 272 #define CONFIG_SYS_PCA953X_MC_GPIO0             0x01 /* PU; */
 273 #define CONFIG_SYS_PCA953X_MC_GPIO1             0x02 /* PU; */
 274 #define CONFIG_SYS_PCA953X_MC_GPIO2             0x04 /* PU; */
 275 #define CONFIG_SYS_PCA953X_MC_GPIO3             0x08 /* PU; */
 276 #define CONFIG_SYS_PCA953X_MC_GPIO4             0x10 /* PU; */
 277 #define CONFIG_SYS_PCA953X_MC_GPIO5             0x20 /* PU; */
 278 #define CONFIG_SYS_PCA953X_MC_GPIO6             0x40 /* PU; */
 279 #define CONFIG_SYS_PCA953X_MC_GPIO7             0x80 /* PU; */
 280
 281 /*
 282  * General PCI
 283  * Memory space is mapped 1-1, but I/O space must start from 0.
 284  */
 285
 286 /* controller 1 - PEX8112 or XMC, depending on build option */
 287 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 288 #define CONFIG_SYS_PCIE1_MEM_PHYS       CONFIG_SYS_PCIE1_MEM_BUS
 289 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x40000000      /* 1G */
 290 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 291 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe8000000
 292 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000      /* 8M */
 293
 294 /*
 295  * Networking options
 296  */
 297 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
 298 #define CONFIG_PHY_GIGE         1       /* Include GbE speed/duplex detection */
 299 #define CONFIG_TSEC_TBI
 300 #define CONFIG_MII              1       /* MII PHY management */
 301 #define CONFIG_MII_DEFAULT_TSEC 1       /* Allow unregistered phys */
 302 #define CONFIG_ETHPRIME         "eTSEC2"
 303
 304 /*
 305  * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
 306  * 1000mbps SGMII link
 307  */
 308 #define CONFIG_TSEC_TBICR_SETTINGS ( \
 309                 TBICR_PHY_RESET \
 310                 | TBICR_FULL_DUPLEX \
 311                 | TBICR_SPEED1_SET \
 312                 )
 313
 314 #define CONFIG_TSEC1            1
 315 #define CONFIG_TSEC1_NAME       "eTSEC1"
 316 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 317 #define TSEC1_PHY_ADDR          1
 318 #define TSEC1_PHYIDX            0
 319 #define CONFIG_HAS_ETH0
 320
 321 #define CONFIG_TSEC2            1
 322 #define CONFIG_TSEC2_NAME       "eTSEC2"
 323 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 324 #define TSEC2_PHY_ADDR          2
 325 #define TSEC2_PHYIDX            0
 326 #define CONFIG_HAS_ETH1
 327
 328 #define CONFIG_TSEC3            1
 329 #define CONFIG_TSEC3_NAME       "eTSEC3"
 330 #define TSEC3_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 331 #define TSEC3_PHY_ADDR          3
 332 #define TSEC3_PHYIDX            0
 333 #define CONFIG_HAS_ETH2
 334
 335 /*
 336  * USB
 337  */
 338 #define CONFIG_USB_EHCI
 339 #define CONFIG_USB_EHCI_FSL
 340 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 341 #define CONFIG_DOS_PARTITION
 342
 343 /*
 344  * Command configuration.
 345  */
 346 #define CONFIG_CMD_DATE
 347 #define CONFIG_CMD_DTT
 348 #define CONFIG_CMD_EEPROM
 349 #define CONFIG_CMD_JFFS2
 350 #define CONFIG_CMD_NAND
 351 #define CONFIG_CMD_PCA953X
 352 #define CONFIG_CMD_PCA953X_INFO
 353 #define CONFIG_CMD_PCI
 354 #define CONFIG_CMD_PCI_ENUM
 355 #define CONFIG_CMD_REGINFO
 356
 357 /*
 358  * Miscellaneous configurable options
 359  */
 360 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 361 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 362 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 363 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 364 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 365 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 366 #define CONFIG_CMDLINE_EDITING  1               /* add command line history     */
 367 #define CONFIG_AUTO_COMPLETE    1               /* add autocompletion support */
 368 #define CONFIG_LOADADDR         0x1000000       /* default location for tftp and bootm */
 369 #define CONFIG_PANIC_HANG                       /* do not reset board on panic */
 370 #define CONFIG_PREBOOT                          /* enable preboot variable */
 371 #define CONFIG_INTEGRITY                        /* support booting INTEGRITY OS */
 372
 373 /*
 374  * For booting Linux, the board info and command line data
 375  * have to be in the first 16 MB of memory, since this is
 376  * the maximum mapped by the Linux kernel during initialization.
 377  */
 378 #define CONFIG_SYS_BOOTMAPSZ    (16 << 20)      /* Initial Memory map for Linux*/
 379 #define CONFIG_SYS_BOOTM_LEN    (16 << 20)      /* Increase max gunzip size */
 380
 381 /*
 382  * Environment Configuration
 383  */
 384 #define CONFIG_ENV_IS_IN_FLASH  1
 385 #define CONFIG_ENV_SECT_SIZE    0x20000         /* 128k (one sector) for env */
 386 #define CONFIG_ENV_SIZE         0x8000
 387 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
 388
 389 /*
 390  * Flash memory map:
 391  * fff80000 - ffffffff     Pri U-Boot (512 KB)
 392  * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
 393  * fff00000 - fff3ffff     Pri FDT (256KB)
 394  * fef00000 - ffefffff     Pri OS image (16MB)
 395  * f8000000 - feefffff     Pri OS Use/Filesystem (111MB)
 396  *
 397  * f7f80000 - f7ffffff     Sec U-Boot (512 KB)
 398  * f7f40000 - f7f7ffff     Sec U-Boot Environment (256 KB)
 399  * f7f00000 - f7f3ffff     Sec FDT (256KB)
 400  * f6f00000 - f7efffff     Sec OS image (16MB)
 401  * f0000000 - f6efffff     Sec OS Use/Filesystem (111MB)
 402  */
 403 #define CONFIG_UBOOT1_ENV_ADDR  __stringify(0xfff80000)
 404 #define CONFIG_UBOOT2_ENV_ADDR  __stringify(0xf7f80000)
 405 #define CONFIG_FDT1_ENV_ADDR    __stringify(0xfff00000)
 406 #define CONFIG_FDT2_ENV_ADDR    __stringify(0xf7f00000)
 407 #define CONFIG_OS1_ENV_ADDR     __stringify(0xfef00000)
 408 #define CONFIG_OS2_ENV_ADDR     __stringify(0xf6f00000)
 409
 410 #define CONFIG_PROG_UBOOT1                                              \
 411         "$download_cmd $loadaddr $ubootfile; "                          \
 412         "if test $? -eq 0; then "                                       \
 413                 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "         \
 414                 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "               \
 415                 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "       \
 416                 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "          \
 417                 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "      \
 418                 "if test $? -ne 0; then "                               \
 419                         "echo PROGRAM FAILED; "                         \
 420                 "else; "                                                \
 421                         "echo PROGRAM SUCCEEDED; "                      \
 422                 "fi; "                                                  \
 423         "else; "                                                        \
 424                 "echo DOWNLOAD FAILED; "                                \
 425         "fi;"
 426
 427 #define CONFIG_PROG_UBOOT2                                              \
 428         "$download_cmd $loadaddr $ubootfile; "                          \
 429         "if test $? -eq 0; then "                                       \
 430                 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "         \
 431                 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "               \
 432                 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "       \
 433                 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "          \
 434                 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "      \
 435                 "if test $? -ne 0; then "                               \
 436                         "echo PROGRAM FAILED; "                         \
 437                 "else; "                                                \
 438                         "echo PROGRAM SUCCEEDED; "                      \
 439                 "fi; "                                                  \
 440         "else; "                                                        \
 441                 "echo DOWNLOAD FAILED; "                                \
 442         "fi;"
 443
 444 #define CONFIG_BOOT_OS_NET                                              \
 445         "$download_cmd $osaddr $osfile; "                               \
 446         "if test $? -eq 0; then "                                       \
 447                 "if test -n $fdtaddr; then "                            \
 448                         "$download_cmd $fdtaddr $fdtfile; "             \
 449                         "if test $? -eq 0; then "                       \
 450                                 "bootm $osaddr - $fdtaddr; "            \
 451                         "else; "                                        \
 452                                 "echo FDT DOWNLOAD FAILED; "            \
 453                         "fi; "                                          \
 454                 "else; "                                                \
 455                         "bootm $osaddr; "                               \
 456                 "fi; "                                                  \
 457         "else; "                                                        \
 458                 "echo OS DOWNLOAD FAILED; "                             \
 459         "fi;"
 460
 461 #define CONFIG_PROG_OS1                                                 \
 462         "$download_cmd $osaddr $osfile; "                               \
 463         "if test $? -eq 0; then "                                       \
 464                 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; "              \
 465                 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "        \
 466                 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "       \
 467                 "if test $? -ne 0; then "                               \
 468                         "echo OS PROGRAM FAILED; "                      \
 469                 "else; "                                                \
 470                         "echo OS PROGRAM SUCCEEDED; "                   \
 471                 "fi; "                                                  \
 472         "else; "                                                        \
 473                 "echo OS DOWNLOAD FAILED; "                             \
 474         "fi;"
 475
 476 #define CONFIG_PROG_OS2                                                 \
 477         "$download_cmd $osaddr $osfile; "                               \
 478         "if test $? -eq 0; then "                                       \
 479                 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; "              \
 480                 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "        \
 481                 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "       \
 482                 "if test $? -ne 0; then "                               \
 483                         "echo OS PROGRAM FAILED; "                      \
 484                 "else; "                                                \
 485                         "echo OS PROGRAM SUCCEEDED; "                   \
 486                 "fi; "                                                  \
 487         "else; "                                                        \
 488                 "echo OS DOWNLOAD FAILED; "                             \
 489         "fi;"
 490
 491 #define CONFIG_PROG_FDT1                                                \
 492         "$download_cmd $fdtaddr $fdtfile; "                             \
 493         "if test $? -eq 0; then "                                       \
 494                 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"              \
 495                 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "      \
 496                 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "     \
 497                 "if test $? -ne 0; then "                               \
 498                         "echo FDT PROGRAM FAILED; "                     \
 499                 "else; "                                                \
 500                         "echo FDT PROGRAM SUCCEEDED; "                  \
 501                 "fi; "                                                  \
 502         "else; "                                                        \
 503                 "echo FDT DOWNLOAD FAILED; "                            \
 504         "fi;"
 505
 506 #define CONFIG_PROG_FDT2                                                \
 507         "$download_cmd $fdtaddr $fdtfile; "                             \
 508         "if test $? -eq 0; then "                                       \
 509                 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"              \
 510                 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "      \
 511                 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "     \
 512                 "if test $? -ne 0; then "                               \
 513                         "echo FDT PROGRAM FAILED; "                     \
 514                 "else; "                                                \
 515                         "echo FDT PROGRAM SUCCEEDED; "                  \
 516                 "fi; "                                                  \
 517         "else; "                                                        \
 518                 "echo FDT DOWNLOAD FAILED; "                            \
 519         "fi;"
 520
 521 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 522         "autoload=yes\0"                                                \
 523         "download_cmd=tftp\0"                                           \
 524         "console_args=console=ttyS0,115200\0"                           \
 525         "root_args=root=/dev/nfs rw\0"                                  \
 526         "misc_args=ip=on\0"                                             \
 527         "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 528         "bootfile=/home/user/file\0"                                    \
 529         "osfile=/home/user/board.uImage\0"                              \
 530         "fdtfile=/home/user/board.dtb\0"                                \
 531         "ubootfile=/home/user/u-boot.bin\0"                             \
 532         "fdtaddr=0x1e00000\0"                                           \
 533         "osaddr=0x1000000\0"                                            \
 534         "loadaddr=0x1000000\0"                                          \
 535         "prog_uboot1="CONFIG_PROG_UBOOT1"\0"                            \
 536         "prog_uboot2="CONFIG_PROG_UBOOT2"\0"                            \
 537         "prog_os1="CONFIG_PROG_OS1"\0"                                  \
 538         "prog_os2="CONFIG_PROG_OS2"\0"                                  \
 539         "prog_fdt1="CONFIG_PROG_FDT1"\0"                                \
 540         "prog_fdt2="CONFIG_PROG_FDT2"\0"                                \
 541         "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"          \
 542         "bootcmd_flash1=run set_bootargs; "                             \
 543                 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
 544         "bootcmd_flash2=run set_bootargs; "                             \
 545                 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
 546         "bootcmd=run bootcmd_flash1\0"
 547 #endif  /* __CONFIG_H */