include/configs/xpedite537x.h

   1 /*
   2  * Copyright 2008 Extreme Engineering Solutions, Inc.
   3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * xpedite537x board configuration file
  10  */
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * High Level Configuration Options
  16  */
  17 #define CONFIG_SYS_BOARD_NAME   "XPedite5370"
  18 #define CONFIG_SYS_FORM_3U_VPX  1
  19 #define CONFIG_BOARD_EARLY_INIT_R       /* Call board_pre_init */
  20
  21 #ifndef CONFIG_SYS_TEXT_BASE
  22 #define CONFIG_SYS_TEXT_BASE    0xfff80000
  23 #endif
  24
  25 #define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup */
  26 #define CONFIG_PCIE1            1       /* PCIE controller 1 */
  27 #define CONFIG_PCIE2            1       /* PCIE controller 2 */
  28 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  29 #define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
  30 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  31 #define CONFIG_FSL_PCIE_RESET   1       /* need PCIe reset errata */
  32 #define CONFIG_FSL_ELBC         1
  33
  34 /*
  35  * Multicore config
  36  */
  37 #define CONFIG_MP
  38 #define CONFIG_BPTR_VIRT_ADDR   0xee000000      /* virt boot page address */
  39 #define CONFIG_MPC8xxx_DISABLE_BPTR             /* Don't leave BPTR enabled */
  40
  41 /*
  42  * DDR config
  43  */
  44 #undef CONFIG_FSL_DDR_INTERACTIVE
  45 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
  46 #define CONFIG_DDR_SPD
  47 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  48 #define SPD_EEPROM_ADDRESS1             0x54    /* Both channels use the */
  49 #define SPD_EEPROM_ADDRESS2             0x54    /* same SPD data         */
  50 #define SPD_EEPROM_OFFSET               0x200   /* OFFSET of SPD in EEPROM */
  51 #define CONFIG_NUM_DDR_CONTROLLERS      2
  52 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  53 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  54 #define CONFIG_DDR_ECC
  55 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  56 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000 /* DDR is system memory*/
  57 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  58 #define CONFIG_VERY_BIG_RAM
  59
  60 #ifndef __ASSEMBLY__
  61 extern unsigned long get_board_sys_clk(unsigned long dummy);
  62 extern unsigned long get_board_ddr_clk(unsigned long dummy);
  63 #endif
  64
  65 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0) /* sysclk for MPC85xx */
  66 #define CONFIG_DDR_CLK_FREQ     get_board_ddr_clk(0) /* ddrclk for MPC85xx */
  67
  68 /*
  69  * These can be toggled for performance analysis, otherwise use default.
  70  */
  71 #define CONFIG_L2_CACHE                 /* toggle L2 cache */
  72 #define CONFIG_BTB                      /* toggle branch predition */
  73 #define CONFIG_ENABLE_36BIT_PHYS        1
  74
  75 #define CONFIG_SYS_CCSRBAR              0xef000000
  76 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  77
  78 /*
  79  * Diagnostics
  80  */
  81 #define CONFIG_SYS_ALT_MEMTEST
  82 #define CONFIG_SYS_MEMTEST_START        0x10000000
  83 #define CONFIG_SYS_MEMTEST_END          0x20000000
  84 #define CONFIG_POST                     (CONFIG_SYS_POST_MEMORY | \
  85                                          CONFIG_SYS_POST_I2C)
  86 #define I2C_ADDR_LIST                   {CONFIG_SYS_I2C_DS1621_ADDR,    \
  87                                          CONFIG_SYS_I2C_DS4510_ADDR,    \
  88                                          CONFIG_SYS_I2C_EEPROM_ADDR,    \
  89                                          CONFIG_SYS_I2C_LM90_ADDR,      \
  90                                          CONFIG_SYS_I2C_PCA953X_ADDR0,  \
  91                                          CONFIG_SYS_I2C_PCA953X_ADDR1,  \
  92                                          CONFIG_SYS_I2C_PCA953X_ADDR2,  \
  93                                          CONFIG_SYS_I2C_PCA953X_ADDR3,  \
  94                                          CONFIG_SYS_I2C_PEX8518_ADDR,   \
  95                                          CONFIG_SYS_I2C_RTC_ADDR}
  96 /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */
  97 #define I2C_ADDR_IGNORE_LIST            {0x50}
  98
  99 /*
 100  * Memory map
 101  * 0x0000_0000  0x7fff_ffff     DDR                     2G Cacheable
 102  * 0x8000_0000  0xbfff_ffff     PCIe1 Mem               1G non-cacheable
 103  * 0xc000_0000  0xcfff_ffff     PCIe2 Mem               256M non-cacheable
 104  * 0xe000_0000  0xe7ff_ffff     SRAM/SSRAM/L1 Cache     128M non-cacheable
 105  * 0xe800_0000  0xe87f_ffff     PCIe1 IO                8M non-cacheable
 106  * 0xe880_0000  0xe8ff_ffff     PCIe2 IO                8M non-cacheable
 107  * 0xee00_0000  0xee00_ffff     Boot page translation   4K non-cacheable
 108  * 0xef00_0000  0xef0f_ffff     CCSR/IMMR               1M non-cacheable
 109  * 0xef80_0000  0xef8f_ffff     NAND Flash              1M non-cacheable
 110  * 0xf000_0000  0xf7ff_ffff     NOR Flash 2             128M non-cacheable
 111  * 0xf800_0000  0xffff_ffff     NOR Flash 1             128M non-cacheable
 112  */
 113
 114 #define CONFIG_SYS_LBC_LCRR     (LCRR_CLKDIV_8 | LCRR_EADC_3)
 115
 116 /*
 117  * NAND flash configuration
 118  */
 119 #define CONFIG_SYS_NAND_BASE            0xef800000
 120 #define CONFIG_SYS_NAND_BASE2           0xef840000 /* Unused at this time */
 121 #define CONFIG_SYS_NAND_BASE_LIST       {CONFIG_SYS_NAND_BASE, \
 122                                          CONFIG_SYS_NAND_BASE2}
 123 #define CONFIG_SYS_MAX_NAND_DEVICE      2
 124 #define CONFIG_NAND_FSL_ELBC
 125
 126 /*
 127  * NOR flash configuration
 128  */
 129 #define CONFIG_SYS_FLASH_BASE           0xf8000000
 130 #define CONFIG_SYS_FLASH_BASE2          0xf0000000
 131 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
 132 #define CONFIG_SYS_MAX_FLASH_BANKS      2               /* number of banks */
 133 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
 134 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Flash Erase Timeout (ms) */
 135 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Flash Write Timeout (ms) */
 136 #define CONFIG_FLASH_CFI_DRIVER
 137 #define CONFIG_SYS_FLASH_CFI
 138 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 139 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST       { {0xfff40000, 0xc0000}, \
 140                                                   {0xf7f40000, 0xc0000} }
 141 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 142
 143 /*
 144  * Chip select configuration
 145  */
 146 /* NOR Flash 0 on CS0 */
 147 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE  | \
 148                                  BR_PS_16               | \
 149                                  BR_V)
 150 #define CONFIG_SYS_OR0_PRELIM   (OR_AM_128MB            | \
 151                                  OR_GPCM_CSNT           | \
 152                                  OR_GPCM_XACS           | \
 153                                  OR_GPCM_ACS_DIV2       | \
 154                                  OR_GPCM_SCY_8          | \
 155                                  OR_GPCM_TRLX           | \
 156                                  OR_GPCM_EHTR           | \
 157                                  OR_GPCM_EAD)
 158
 159 /* NOR Flash 1 on CS1 */
 160 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FLASH_BASE2 | \
 161                                  BR_PS_16               | \
 162                                  BR_V)
 163 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 164
 165 /* NAND flash on CS2 */
 166 #define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_NAND_BASE   | \
 167                                  (2<<BR_DECC_SHIFT)     | \
 168                                  BR_PS_8                | \
 169                                  BR_MS_FCM              | \
 170                                  BR_V)
 171
 172 /* NAND flash on CS2 */
 173 #define CONFIG_SYS_OR2_PRELIM   (OR_AM_256KB    | \
 174                                  OR_FCM_PGS     | \
 175                                  OR_FCM_CSCT    | \
 176                                  OR_FCM_CST     | \
 177                                  OR_FCM_CHT     | \
 178                                  OR_FCM_SCY_1   | \
 179                                  OR_FCM_TRLX    | \
 180                                  OR_FCM_EHTR)
 181
 182 /* NAND flash on CS3 */
 183 #define CONFIG_SYS_BR3_PRELIM   (CONFIG_SYS_NAND_BASE2  | \
 184                                  (2<<BR_DECC_SHIFT)     | \
 185                                  BR_PS_8                | \
 186                                  BR_MS_FCM              | \
 187                                  BR_V)
 188 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 189
 190 /*
 191  * Use L1 as initial stack
 192  */
 193 #define CONFIG_SYS_INIT_RAM_LOCK        1
 194 #define CONFIG_SYS_INIT_RAM_ADDR        0xe0000000
 195 #define CONFIG_SYS_INIT_RAM_SIZE                0x00004000
 196
 197 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 198 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 199
 200 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 KB for Mon */
 201 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc */
 202
 203 /*
 204  * Serial Port
 205  */
 206 #define CONFIG_CONS_INDEX               1
 207 #define CONFIG_SYS_NS16550_SERIAL
 208 #define CONFIG_SYS_NS16550_REG_SIZE     1
 209 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 210 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 211 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 212 #define CONFIG_SYS_BAUDRATE_TABLE       \
 213         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 214 #define CONFIG_BAUDRATE                 115200
 215 #define CONFIG_LOADS_ECHO               1       /* echo on for serial download */
 216 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 217
 218 /*
 219  * I2C
 220  */
 221 #define CONFIG_SYS_I2C
 222 #define CONFIG_SYS_I2C_FSL
 223 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 224 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 225 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 226 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 227 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 228 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 229 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 230
 231 /* PEX8518 slave I2C interface */
 232 #define CONFIG_SYS_I2C_PEX8518_ADDR     0x70
 233
 234 /* I2C DS1631 temperature sensor */
 235 #define CONFIG_SYS_I2C_DS1621_ADDR      0x48
 236 #define CONFIG_DTT_DS1621
 237 #define CONFIG_DTT_SENSORS              { 0 }
 238 #define CONFIG_SYS_I2C_LM90_ADDR        0x4c
 239
 240 /* I2C EEPROM - AT24C128B */
 241 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x54
 242 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
 243 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
 244 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
 245
 246 /* I2C RTC */
 247 #define CONFIG_RTC_M41T11               1
 248 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 249 #define CONFIG_SYS_M41T11_BASE_YEAR     2000
 250
 251 /* GPIO/EEPROM/SRAM */
 252 #define CONFIG_DS4510
 253 #define CONFIG_SYS_I2C_DS4510_ADDR      0x51
 254
 255 /* GPIO */
 256 #define CONFIG_PCA953X
 257 #define CONFIG_SYS_I2C_PCA953X_ADDR0    0x18
 258 #define CONFIG_SYS_I2C_PCA953X_ADDR1    0x1c
 259 #define CONFIG_SYS_I2C_PCA953X_ADDR2    0x1e
 260 #define CONFIG_SYS_I2C_PCA953X_ADDR3    0x1f
 261 #define CONFIG_SYS_I2C_PCA953X_ADDR     CONFIG_SYS_I2C_PCA953X_ADDR0
 262
 263 /*
 264  * PU = pulled high, PD = pulled low
 265  * I = input, O = output, IO = input/output
 266  */
 267 /* PCA9557 @ 0x18*/
 268 #define CONFIG_SYS_PCA953X_C0_SER0_EN           0x01 /* PU; UART0 enable (1: enabled) */
 269 #define CONFIG_SYS_PCA953X_C0_SER0_MODE         0x02 /* PU; UART0 serial mode select */
 270 #define CONFIG_SYS_PCA953X_C0_SER1_EN           0x04 /* PU; UART1 enable (1: enabled) */
 271 #define CONFIG_SYS_PCA953X_C0_SER1_MODE         0x08 /* PU; UART1 serial mode select */
 272 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS     0x10 /* PU; Boot flash CS select */
 273 #define CONFIG_SYS_PCA953X_NVM_WP               0x20 /* PU; Set to 0 to enable NVM writing */
 274 #define CONFIG_SYS_PCA953X_C0_VCORE_VID2        0x40 /* VID2 of ISL6262 */
 275 #define CONFIG_SYS_PCA953X_C0_VCORE_VID3        0x80 /* VID3 of ISL6262 */
 276
 277 /* PCA9557 @ 0x1c*/
 278 #define CONFIG_SYS_PCA953X_XMC0_ROOT0           0x01 /* PU; Low if XMC is RC */
 279 #define CONFIG_SYS_PCA953X_XMC0_MVMR0           0x02 /* XMC EEPROM write protect */
 280 #define CONFIG_SYS_PCA953X_XMC0_WAKE            0x04 /* PU; XMC wake */
 281 #define CONFIG_SYS_PCA953X_XMC0_BIST            0x08 /* PU; XMC built in self test */
 282 #define CONFIG_SYS_PCA953X_XMC_PRESENT          0x10 /* PU; Low if XMC module installed */
 283 #define CONFIG_SYS_PCA953X_PMC_PRESENT          0x20 /* PU; Low if PMC module installed */
 284 #define CONFIG_SYS_PCA953X_PMC0_MONARCH         0x40 /* PMC monarch mode enable */
 285 #define CONFIG_SYS_PCA953X_PMC0_EREADY          0x80 /* PU; PMC PCI eready */
 286
 287 /* PCA9557 @ 0x1e*/
 288 #define CONFIG_SYS_PCA953X_P0_GA0               0x01 /* PU; VPX Geographical address */
 289 #define CONFIG_SYS_PCA953X_P0_GA1               0x02 /* PU; VPX Geographical address */
 290 #define CONFIG_SYS_PCA953X_P0_GA2               0x04 /* PU; VPX Geographical address */
 291 #define CONFIG_SYS_PCA953X_P0_GA3               0x08 /* PU; VPX Geographical address */
 292 #define CONFIG_SYS_PCA953X_P0_GA4               0x10 /* PU; VPX Geographical address */
 293 #define CONFIG_SYS_PCA953X_P0_GAP               0x20 /* PU; tied to VPX P0.GAP */
 294 #define CONFIG_SYS_PCA953X_P1_SYSEN             0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */
 295
 296 /* PCA9557 @ 0x1f */
 297 #define CONFIG_SYS_PCA953X_GPIO_VPX0            0x01 /* PU */
 298 #define CONFIG_SYS_PCA953X_GPIO_VPX1            0x02 /* PU */
 299 #define CONFIG_SYS_PCA953X_GPIO_VPX2            0x04 /* PU */
 300 #define CONFIG_SYS_PCA953X_GPIO_VPX3            0x08 /* PU */
 301 #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL        0x10 /* PD; I2C master source for FRU SEEPROM */
 302
 303 /*
 304  * General PCI
 305  * Memory space is mapped 1-1, but I/O space must start from 0.
 306  */
 307 /* PCIE1 - VPX P1 */
 308 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 309 #define CONFIG_SYS_PCIE1_MEM_PHYS       CONFIG_SYS_PCIE1_MEM_BUS
 310 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x40000000      /* 1G */
 311 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 312 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe8000000
 313 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000      /* 8M */
 314
 315 /* PCIE2 - PEX8518 */
 316 #define CONFIG_SYS_PCIE2_MEM_BUS        0xc0000000
 317 #define CONFIG_SYS_PCIE2_MEM_PHYS       CONFIG_SYS_PCIE2_MEM_BUS
 318 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000      /* 256M */
 319 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 320 #define CONFIG_SYS_PCIE2_IO_PHYS        0xe8800000
 321 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00800000      /* 8M */
 322
 323 /*
 324  * Networking options
 325  */
 326 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
 327 #define CONFIG_PHY_GIGE         1       /* Include GbE speed/duplex detection */
 328 #define CONFIG_TSEC_TBI
 329 #define CONFIG_MII              1       /* MII PHY management */
 330 #define CONFIG_MII_DEFAULT_TSEC 1       /* Allow unregistered phys */
 331 #define CONFIG_ETHPRIME         "eTSEC2"
 332
 333 /*
 334  * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
 335  * 1000mbps SGMII link
 336  */
 337 #define CONFIG_TSEC_TBICR_SETTINGS ( \
 338                 TBICR_PHY_RESET \
 339                 | TBICR_FULL_DUPLEX \
 340                 | TBICR_SPEED1_SET \
 341                 )
 342
 343 #define CONFIG_TSEC1            1
 344 #define CONFIG_TSEC1_NAME       "eTSEC1"
 345 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 346 #define TSEC1_PHY_ADDR          1
 347 #define TSEC1_PHYIDX            0
 348 #define CONFIG_HAS_ETH0
 349
 350 #define CONFIG_TSEC2            1
 351 #define CONFIG_TSEC2_NAME       "eTSEC2"
 352 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 353 #define TSEC2_PHY_ADDR          2
 354 #define TSEC2_PHYIDX            0
 355 #define CONFIG_HAS_ETH1
 356
 357 /*
 358  * Command configuration.
 359  */
 360 #define CONFIG_CMD_DATE
 361 #define CONFIG_CMD_DS4510
 362 #define CONFIG_CMD_DS4510_INFO
 363 #define CONFIG_CMD_DTT
 364 #define CONFIG_CMD_EEPROM
 365 #define CONFIG_CMD_JFFS2
 366 #define CONFIG_CMD_NAND
 367 #define CONFIG_CMD_PCA953X
 368 #define CONFIG_CMD_PCA953X_INFO
 369 #define CONFIG_CMD_PCI
 370 #define CONFIG_CMD_PCI_ENUM
 371 #define CONFIG_CMD_REGINFO
 372
 373 /*
 374  * Miscellaneous configurable options
 375  */
 376 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 377 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 378 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 379 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 380 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 381 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 382 #define CONFIG_CMDLINE_EDITING  1               /* add command line history     */
 383 #define CONFIG_AUTO_COMPLETE    1               /* add autocompletion support */
 384 #define CONFIG_LOADADDR         0x1000000       /* default location for tftp and bootm */
 385 #define CONFIG_PANIC_HANG                       /* do not reset board on panic */
 386 #define CONFIG_PREBOOT                          /* enable preboot variable */
 387 #define CONFIG_INTEGRITY                        /* support booting INTEGRITY OS */
 388
 389 /*
 390  * For booting Linux, the board info and command line data
 391  * have to be in the first 16 MB of memory, since this is
 392  * the maximum mapped by the Linux kernel during initialization.
 393  */
 394 #define CONFIG_SYS_BOOTMAPSZ    (16 << 20)      /* Initial Memory map for Linux*/
 395 #define CONFIG_SYS_BOOTM_LEN    (16 << 20)      /* Increase max gunzip size */
 396
 397 /*
 398  * Environment Configuration
 399  */
 400 #define CONFIG_ENV_IS_IN_FLASH  1
 401 #define CONFIG_ENV_SECT_SIZE    0x20000         /* 128k (one sector) for env */
 402 #define CONFIG_ENV_SIZE         0x8000
 403 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
 404
 405 /*
 406  * Flash memory map:
 407  * fff80000 - ffffffff     Pri U-Boot (512 KB)
 408  * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
 409  * fff00000 - fff3ffff     Pri FDT (256KB)
 410  * fef00000 - ffefffff     Pri OS image (16MB)
 411  * f8000000 - feefffff     Pri OS Use/Filesystem (111MB)
 412  *
 413  * f7f80000 - f7ffffff     Sec U-Boot (512 KB)
 414  * f7f40000 - f7f7ffff     Sec U-Boot Environment (256 KB)
 415  * f7f00000 - f7f3ffff     Sec FDT (256KB)
 416  * f6f00000 - f7efffff     Sec OS image (16MB)
 417  * f0000000 - f6efffff     Sec OS Use/Filesystem (111MB)
 418  */
 419 #define CONFIG_UBOOT1_ENV_ADDR  __stringify(0xfff80000)
 420 #define CONFIG_UBOOT2_ENV_ADDR  __stringify(0xf7f80000)
 421 #define CONFIG_FDT1_ENV_ADDR    __stringify(0xfff00000)
 422 #define CONFIG_FDT2_ENV_ADDR    __stringify(0xf7f00000)
 423 #define CONFIG_OS1_ENV_ADDR     __stringify(0xfef00000)
 424 #define CONFIG_OS2_ENV_ADDR     __stringify(0xf6f00000)
 425
 426 #define CONFIG_PROG_UBOOT1                                              \
 427         "$download_cmd $loadaddr $ubootfile; "                          \
 428         "if test $? -eq 0; then "                                       \
 429                 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "         \
 430                 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "               \
 431                 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "       \
 432                 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "          \
 433                 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "      \
 434                 "if test $? -ne 0; then "                               \
 435                         "echo PROGRAM FAILED; "                         \
 436                 "else; "                                                \
 437                         "echo PROGRAM SUCCEEDED; "                      \
 438                 "fi; "                                                  \
 439         "else; "                                                        \
 440                 "echo DOWNLOAD FAILED; "                                \
 441         "fi;"
 442
 443 #define CONFIG_PROG_UBOOT2                                              \
 444         "$download_cmd $loadaddr $ubootfile; "                          \
 445         "if test $? -eq 0; then "                                       \
 446                 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "         \
 447                 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "               \
 448                 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "       \
 449                 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "          \
 450                 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "      \
 451                 "if test $? -ne 0; then "                               \
 452                         "echo PROGRAM FAILED; "                         \
 453                 "else; "                                                \
 454                         "echo PROGRAM SUCCEEDED; "                      \
 455                 "fi; "                                                  \
 456         "else; "                                                        \
 457                 "echo DOWNLOAD FAILED; "                                \
 458         "fi;"
 459
 460 #define CONFIG_BOOT_OS_NET                                              \
 461         "$download_cmd $osaddr $osfile; "                               \
 462         "if test $? -eq 0; then "                                       \
 463                 "if test -n $fdtaddr; then "                            \
 464                         "$download_cmd $fdtaddr $fdtfile; "             \
 465                         "if test $? -eq 0; then "                       \
 466                                 "bootm $osaddr - $fdtaddr; "            \
 467                         "else; "                                        \
 468                                 "echo FDT DOWNLOAD FAILED; "            \
 469                         "fi; "                                          \
 470                 "else; "                                                \
 471                         "bootm $osaddr; "                               \
 472                 "fi; "                                                  \
 473         "else; "                                                        \
 474                 "echo OS DOWNLOAD FAILED; "                             \
 475         "fi;"
 476
 477 #define CONFIG_PROG_OS1                                                 \
 478         "$download_cmd $osaddr $osfile; "                               \
 479         "if test $? -eq 0; then "                                       \
 480                 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; "              \
 481                 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "        \
 482                 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "       \
 483                 "if test $? -ne 0; then "                               \
 484                         "echo OS PROGRAM FAILED; "                      \
 485                 "else; "                                                \
 486                         "echo OS PROGRAM SUCCEEDED; "                   \
 487                 "fi; "                                                  \
 488         "else; "                                                        \
 489                 "echo OS DOWNLOAD FAILED; "                             \
 490         "fi;"
 491
 492 #define CONFIG_PROG_OS2                                                 \
 493         "$download_cmd $osaddr $osfile; "                               \
 494         "if test $? -eq 0; then "                                       \
 495                 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; "              \
 496                 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "        \
 497                 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "       \
 498                 "if test $? -ne 0; then "                               \
 499                         "echo OS PROGRAM FAILED; "                      \
 500                 "else; "                                                \
 501                         "echo OS PROGRAM SUCCEEDED; "                   \
 502                 "fi; "                                                  \
 503         "else; "                                                        \
 504                 "echo OS DOWNLOAD FAILED; "                             \
 505         "fi;"
 506
 507 #define CONFIG_PROG_FDT1                                                \
 508         "$download_cmd $fdtaddr $fdtfile; "                             \
 509         "if test $? -eq 0; then "                                       \
 510                 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"              \
 511                 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "      \
 512                 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "     \
 513                 "if test $? -ne 0; then "                               \
 514                         "echo FDT PROGRAM FAILED; "                     \
 515                 "else; "                                                \
 516                         "echo FDT PROGRAM SUCCEEDED; "                  \
 517                 "fi; "                                                  \
 518         "else; "                                                        \
 519                 "echo FDT DOWNLOAD FAILED; "                            \
 520         "fi;"
 521
 522 #define CONFIG_PROG_FDT2                                                \
 523         "$download_cmd $fdtaddr $fdtfile; "                             \
 524         "if test $? -eq 0; then "                                       \
 525                 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"              \
 526                 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "      \
 527                 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "     \
 528                 "if test $? -ne 0; then "                               \
 529                         "echo FDT PROGRAM FAILED; "                     \
 530                 "else; "                                                \
 531                         "echo FDT PROGRAM SUCCEEDED; "                  \
 532                 "fi; "                                                  \
 533         "else; "                                                        \
 534                 "echo FDT DOWNLOAD FAILED; "                            \
 535         "fi;"
 536
 537 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 538         "autoload=yes\0"                                                \
 539         "download_cmd=tftp\0"                                           \
 540         "console_args=console=ttyS0,115200\0"                           \
 541         "root_args=root=/dev/nfs rw\0"                                  \
 542         "misc_args=ip=on\0"                                             \
 543         "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 544         "bootfile=/home/user/file\0"                                    \
 545         "osfile=/home/user/board.uImage\0"                              \
 546         "fdtfile=/home/user/board.dtb\0"                                \
 547         "ubootfile=/home/user/u-boot.bin\0"                             \
 548         "fdtaddr=0x1e00000\0"                                           \
 549         "osaddr=0x1000000\0"                                            \
 550         "loadaddr=0x1000000\0"                                          \
 551         "prog_uboot1="CONFIG_PROG_UBOOT1"\0"                            \
 552         "prog_uboot2="CONFIG_PROG_UBOOT2"\0"                            \
 553         "prog_os1="CONFIG_PROG_OS1"\0"                                  \
 554         "prog_os2="CONFIG_PROG_OS2"\0"                                  \
 555         "prog_fdt1="CONFIG_PROG_FDT1"\0"                                \
 556         "prog_fdt2="CONFIG_PROG_FDT2"\0"                                \
 557         "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"          \
 558         "bootcmd_flash1=run set_bootargs; "                             \
 559                 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
 560         "bootcmd_flash2=run set_bootargs; "                             \
 561                 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
 562         "bootcmd=run bootcmd_flash1\0"
 563 #endif  /* __CONFIG_H */