include/configs/xpedite537x.h

   1 /*
   2  * Copyright 2008 Extreme Engineering Solutions, Inc.
   3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * xpedite537x board configuration file
  10  */
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * High Level Configuration Options
  16  */
  17 #define CONFIG_SYS_BOARD_NAME   "XPedite5370"
  18 #define CONFIG_SYS_FORM_3U_VPX  1
  19
  20 #define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup */
  21 #define CONFIG_PCIE1            1       /* PCIE controller 1 */
  22 #define CONFIG_PCIE2            1       /* PCIE controller 2 */
  23 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  24 #define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
  25 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  26 #define CONFIG_FSL_PCIE_RESET   1       /* need PCIe reset errata */
  27
  28 /*
  29  * Multicore config
  30  */
  31 #define CONFIG_MP
  32 #define CONFIG_BPTR_VIRT_ADDR   0xee000000      /* virt boot page address */
  33 #define CONFIG_MPC8xxx_DISABLE_BPTR             /* Don't leave BPTR enabled */
  34
  35 /*
  36  * DDR config
  37  */
  38 #undef CONFIG_FSL_DDR_INTERACTIVE
  39 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
  40 #define CONFIG_DDR_SPD
  41 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  42 #define SPD_EEPROM_ADDRESS1             0x54    /* Both channels use the */
  43 #define SPD_EEPROM_ADDRESS2             0x54    /* same SPD data         */
  44 #define SPD_EEPROM_OFFSET               0x200   /* OFFSET of SPD in EEPROM */
  45 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  46 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  47 #define CONFIG_DDR_ECC
  48 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  49 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000 /* DDR is system memory*/
  50 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  51 #define CONFIG_VERY_BIG_RAM
  52
  53 #ifndef __ASSEMBLY__
  54 extern unsigned long get_board_sys_clk(unsigned long dummy);
  55 extern unsigned long get_board_ddr_clk(unsigned long dummy);
  56 #endif
  57
  58 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0) /* sysclk for MPC85xx */
  59 #define CONFIG_DDR_CLK_FREQ     get_board_ddr_clk(0) /* ddrclk for MPC85xx */
  60
  61 /*
  62  * These can be toggled for performance analysis, otherwise use default.
  63  */
  64 #define CONFIG_L2_CACHE                 /* toggle L2 cache */
  65 #define CONFIG_BTB                      /* toggle branch predition */
  66 #define CONFIG_ENABLE_36BIT_PHYS        1
  67
  68 #define CONFIG_SYS_CCSRBAR              0xef000000
  69 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  70
  71 /*
  72  * Diagnostics
  73  */
  74 #define CONFIG_SYS_MEMTEST_START        0x10000000
  75 #define CONFIG_SYS_MEMTEST_END          0x20000000
  76 #define CONFIG_POST                     (CONFIG_SYS_POST_MEMORY | \
  77                                          CONFIG_SYS_POST_I2C)
  78 /* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */
  79 #define I2C_ADDR_IGNORE_LIST            {0x50}
  80
  81 /*
  82  * Memory map
  83  * 0x0000_0000  0x7fff_ffff     DDR                     2G Cacheable
  84  * 0x8000_0000  0xbfff_ffff     PCIe1 Mem               1G non-cacheable
  85  * 0xc000_0000  0xcfff_ffff     PCIe2 Mem               256M non-cacheable
  86  * 0xe000_0000  0xe7ff_ffff     SRAM/SSRAM/L1 Cache     128M non-cacheable
  87  * 0xe800_0000  0xe87f_ffff     PCIe1 IO                8M non-cacheable
  88  * 0xe880_0000  0xe8ff_ffff     PCIe2 IO                8M non-cacheable
  89  * 0xee00_0000  0xee00_ffff     Boot page translation   4K non-cacheable
  90  * 0xef00_0000  0xef0f_ffff     CCSR/IMMR               1M non-cacheable
  91  * 0xef80_0000  0xef8f_ffff     NAND Flash              1M non-cacheable
  92  * 0xf000_0000  0xf7ff_ffff     NOR Flash 2             128M non-cacheable
  93  * 0xf800_0000  0xffff_ffff     NOR Flash 1             128M non-cacheable
  94  */
  95
  96 #define CONFIG_SYS_LBC_LCRR     (LCRR_CLKDIV_8 | LCRR_EADC_3)
  97
  98 /*
  99  * NAND flash configuration
 100  */
 101 #define CONFIG_SYS_NAND_BASE            0xef800000
 102 #define CONFIG_SYS_NAND_BASE2           0xef840000 /* Unused at this time */
 103 #define CONFIG_SYS_NAND_BASE_LIST       {CONFIG_SYS_NAND_BASE, \
 104                                          CONFIG_SYS_NAND_BASE2}
 105 #define CONFIG_SYS_MAX_NAND_DEVICE      2
 106 #define CONFIG_NAND_FSL_ELBC
 107
 108 /*
 109  * NOR flash configuration
 110  */
 111 #define CONFIG_SYS_FLASH_BASE           0xf8000000
 112 #define CONFIG_SYS_FLASH_BASE2          0xf0000000
 113 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
 114 #define CONFIG_SYS_MAX_FLASH_BANKS      2               /* number of banks */
 115 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
 116 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Flash Erase Timeout (ms) */
 117 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Flash Write Timeout (ms) */
 118 #define CONFIG_FLASH_CFI_DRIVER
 119 #define CONFIG_SYS_FLASH_CFI
 120 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 121 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST       { {0xfff40000, 0xc0000}, \
 122                                                   {0xf7f40000, 0xc0000} }
 123 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 124
 125 /*
 126  * Chip select configuration
 127  */
 128 /* NOR Flash 0 on CS0 */
 129 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE  | \
 130                                  BR_PS_16               | \
 131                                  BR_V)
 132 #define CONFIG_SYS_OR0_PRELIM   (OR_AM_128MB            | \
 133                                  OR_GPCM_CSNT           | \
 134                                  OR_GPCM_XACS           | \
 135                                  OR_GPCM_ACS_DIV2       | \
 136                                  OR_GPCM_SCY_8          | \
 137                                  OR_GPCM_TRLX           | \
 138                                  OR_GPCM_EHTR           | \
 139                                  OR_GPCM_EAD)
 140
 141 /* NOR Flash 1 on CS1 */
 142 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FLASH_BASE2 | \
 143                                  BR_PS_16               | \
 144                                  BR_V)
 145 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 146
 147 /* NAND flash on CS2 */
 148 #define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_NAND_BASE   | \
 149                                  (2<<BR_DECC_SHIFT)     | \
 150                                  BR_PS_8                | \
 151                                  BR_MS_FCM              | \
 152                                  BR_V)
 153
 154 /* NAND flash on CS2 */
 155 #define CONFIG_SYS_OR2_PRELIM   (OR_AM_256KB    | \
 156                                  OR_FCM_PGS     | \
 157                                  OR_FCM_CSCT    | \
 158                                  OR_FCM_CST     | \
 159                                  OR_FCM_CHT     | \
 160                                  OR_FCM_SCY_1   | \
 161                                  OR_FCM_TRLX    | \
 162                                  OR_FCM_EHTR)
 163
 164 /* NAND flash on CS3 */
 165 #define CONFIG_SYS_BR3_PRELIM   (CONFIG_SYS_NAND_BASE2  | \
 166                                  (2<<BR_DECC_SHIFT)     | \
 167                                  BR_PS_8                | \
 168                                  BR_MS_FCM              | \
 169                                  BR_V)
 170 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 171
 172 /*
 173  * Use L1 as initial stack
 174  */
 175 #define CONFIG_SYS_INIT_RAM_LOCK        1
 176 #define CONFIG_SYS_INIT_RAM_ADDR        0xe0000000
 177 #define CONFIG_SYS_INIT_RAM_SIZE                0x00004000
 178
 179 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 180 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 181
 182 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 KB for Mon */
 183 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc */
 184
 185 /*
 186  * Serial Port
 187  */
 188 #define CONFIG_SYS_NS16550_SERIAL
 189 #define CONFIG_SYS_NS16550_REG_SIZE     1
 190 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 191 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 192 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 193 #define CONFIG_SYS_BAUDRATE_TABLE       \
 194         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 195 #define CONFIG_LOADS_ECHO               1       /* echo on for serial download */
 196 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 197
 198 /*
 199  * I2C
 200  */
 201 #define CONFIG_SYS_I2C
 202 #define CONFIG_SYS_I2C_FSL
 203 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 204 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 205 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 206 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 207 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 208 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 209 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 210
 211 /* PEX8518 slave I2C interface */
 212 #define CONFIG_SYS_I2C_PEX8518_ADDR     0x70
 213
 214 /* I2C DS1631 temperature sensor */
 215 #define CONFIG_SYS_I2C_LM90_ADDR        0x4c
 216
 217 /* I2C EEPROM - AT24C128B */
 218 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x54
 219 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
 220 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
 221 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
 222
 223 /* I2C RTC */
 224 #define CONFIG_RTC_M41T11               1
 225 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 226 #define CONFIG_SYS_M41T11_BASE_YEAR     2000
 227
 228 /* GPIO */
 229 #define CONFIG_PCA953X
 230 #define CONFIG_SYS_I2C_PCA953X_ADDR0    0x18
 231 #define CONFIG_SYS_I2C_PCA953X_ADDR1    0x1c
 232 #define CONFIG_SYS_I2C_PCA953X_ADDR2    0x1e
 233 #define CONFIG_SYS_I2C_PCA953X_ADDR3    0x1f
 234 #define CONFIG_SYS_I2C_PCA953X_ADDR     CONFIG_SYS_I2C_PCA953X_ADDR0
 235
 236 /*
 237  * PU = pulled high, PD = pulled low
 238  * I = input, O = output, IO = input/output
 239  */
 240 /* PCA9557 @ 0x18*/
 241 #define CONFIG_SYS_PCA953X_C0_SER0_EN           0x01 /* PU; UART0 enable (1: enabled) */
 242 #define CONFIG_SYS_PCA953X_C0_SER0_MODE         0x02 /* PU; UART0 serial mode select */
 243 #define CONFIG_SYS_PCA953X_C0_SER1_EN           0x04 /* PU; UART1 enable (1: enabled) */
 244 #define CONFIG_SYS_PCA953X_C0_SER1_MODE         0x08 /* PU; UART1 serial mode select */
 245 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS     0x10 /* PU; Boot flash CS select */
 246 #define CONFIG_SYS_PCA953X_NVM_WP               0x20 /* PU; Set to 0 to enable NVM writing */
 247 #define CONFIG_SYS_PCA953X_C0_VCORE_VID2        0x40 /* VID2 of ISL6262 */
 248 #define CONFIG_SYS_PCA953X_C0_VCORE_VID3        0x80 /* VID3 of ISL6262 */
 249
 250 /* PCA9557 @ 0x1c*/
 251 #define CONFIG_SYS_PCA953X_XMC0_ROOT0           0x01 /* PU; Low if XMC is RC */
 252 #define CONFIG_SYS_PCA953X_XMC0_MVMR0           0x02 /* XMC EEPROM write protect */
 253 #define CONFIG_SYS_PCA953X_XMC0_WAKE            0x04 /* PU; XMC wake */
 254 #define CONFIG_SYS_PCA953X_XMC0_BIST            0x08 /* PU; XMC built in self test */
 255 #define CONFIG_SYS_PCA953X_XMC_PRESENT          0x10 /* PU; Low if XMC module installed */
 256 #define CONFIG_SYS_PCA953X_PMC_PRESENT          0x20 /* PU; Low if PMC module installed */
 257 #define CONFIG_SYS_PCA953X_PMC0_MONARCH         0x40 /* PMC monarch mode enable */
 258 #define CONFIG_SYS_PCA953X_PMC0_EREADY          0x80 /* PU; PMC PCI eready */
 259
 260 /* PCA9557 @ 0x1e*/
 261 #define CONFIG_SYS_PCA953X_P0_GA0               0x01 /* PU; VPX Geographical address */
 262 #define CONFIG_SYS_PCA953X_P0_GA1               0x02 /* PU; VPX Geographical address */
 263 #define CONFIG_SYS_PCA953X_P0_GA2               0x04 /* PU; VPX Geographical address */
 264 #define CONFIG_SYS_PCA953X_P0_GA3               0x08 /* PU; VPX Geographical address */
 265 #define CONFIG_SYS_PCA953X_P0_GA4               0x10 /* PU; VPX Geographical address */
 266 #define CONFIG_SYS_PCA953X_P0_GAP               0x20 /* PU; tied to VPX P0.GAP */
 267 #define CONFIG_SYS_PCA953X_P1_SYSEN             0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */
 268
 269 /* PCA9557 @ 0x1f */
 270 #define CONFIG_SYS_PCA953X_GPIO_VPX0            0x01 /* PU */
 271 #define CONFIG_SYS_PCA953X_GPIO_VPX1            0x02 /* PU */
 272 #define CONFIG_SYS_PCA953X_GPIO_VPX2            0x04 /* PU */
 273 #define CONFIG_SYS_PCA953X_GPIO_VPX3            0x08 /* PU */
 274 #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL        0x10 /* PD; I2C master source for FRU SEEPROM */
 275
 276 /*
 277  * General PCI
 278  * Memory space is mapped 1-1, but I/O space must start from 0.
 279  */
 280 /* PCIE1 - VPX P1 */
 281 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 282 #define CONFIG_SYS_PCIE1_MEM_PHYS       CONFIG_SYS_PCIE1_MEM_BUS
 283 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x40000000      /* 1G */
 284 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 285 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe8000000
 286 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000      /* 8M */
 287
 288 /* PCIE2 - PEX8518 */
 289 #define CONFIG_SYS_PCIE2_MEM_BUS        0xc0000000
 290 #define CONFIG_SYS_PCIE2_MEM_PHYS       CONFIG_SYS_PCIE2_MEM_BUS
 291 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000      /* 256M */
 292 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 293 #define CONFIG_SYS_PCIE2_IO_PHYS        0xe8800000
 294 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00800000      /* 8M */
 295
 296 /*
 297  * Networking options
 298  */
 299 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
 300 #define CONFIG_TSEC_TBI
 301 #define CONFIG_MII              1       /* MII PHY management */
 302 #define CONFIG_MII_DEFAULT_TSEC 1       /* Allow unregistered phys */
 303 #define CONFIG_ETHPRIME         "eTSEC2"
 304
 305 /*
 306  * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
 307  * 1000mbps SGMII link
 308  */
 309 #define CONFIG_TSEC_TBICR_SETTINGS ( \
 310                 TBICR_PHY_RESET \
 311                 | TBICR_FULL_DUPLEX \
 312                 | TBICR_SPEED1_SET \
 313                 )
 314
 315 #define CONFIG_TSEC1            1
 316 #define CONFIG_TSEC1_NAME       "eTSEC1"
 317 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 318 #define TSEC1_PHY_ADDR          1
 319 #define TSEC1_PHYIDX            0
 320 #define CONFIG_HAS_ETH0
 321
 322 #define CONFIG_TSEC2            1
 323 #define CONFIG_TSEC2_NAME       "eTSEC2"
 324 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 325 #define TSEC2_PHY_ADDR          2
 326 #define TSEC2_PHYIDX            0
 327 #define CONFIG_HAS_ETH1
 328
 329 /*
 330  * Miscellaneous configurable options
 331  */
 332 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 333 #define CONFIG_LOADADDR         0x1000000       /* default location for tftp and bootm */
 334 #define CONFIG_PREBOOT                          /* enable preboot variable */
 335 #define CONFIG_INTEGRITY                        /* support booting INTEGRITY OS */
 336
 337 /*
 338  * For booting Linux, the board info and command line data
 339  * have to be in the first 16 MB of memory, since this is
 340  * the maximum mapped by the Linux kernel during initialization.
 341  */
 342 #define CONFIG_SYS_BOOTMAPSZ    (16 << 20)      /* Initial Memory map for Linux*/
 343 #define CONFIG_SYS_BOOTM_LEN    (16 << 20)      /* Increase max gunzip size */
 344
 345 /*
 346  * Environment Configuration
 347  */
 348 #define CONFIG_ENV_SECT_SIZE    0x20000         /* 128k (one sector) for env */
 349 #define CONFIG_ENV_SIZE         0x8000
 350 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
 351
 352 /*
 353  * Flash memory map:
 354  * fff80000 - ffffffff     Pri U-Boot (512 KB)
 355  * fff40000 - fff7ffff     Pri U-Boot Environment (256 KB)
 356  * fff00000 - fff3ffff     Pri FDT (256KB)
 357  * fef00000 - ffefffff     Pri OS image (16MB)
 358  * f8000000 - feefffff     Pri OS Use/Filesystem (111MB)
 359  *
 360  * f7f80000 - f7ffffff     Sec U-Boot (512 KB)
 361  * f7f40000 - f7f7ffff     Sec U-Boot Environment (256 KB)
 362  * f7f00000 - f7f3ffff     Sec FDT (256KB)
 363  * f6f00000 - f7efffff     Sec OS image (16MB)
 364  * f0000000 - f6efffff     Sec OS Use/Filesystem (111MB)
 365  */
 366 #define CONFIG_UBOOT1_ENV_ADDR  __stringify(0xfff80000)
 367 #define CONFIG_UBOOT2_ENV_ADDR  __stringify(0xf7f80000)
 368 #define CONFIG_FDT1_ENV_ADDR    __stringify(0xfff00000)
 369 #define CONFIG_FDT2_ENV_ADDR    __stringify(0xf7f00000)
 370 #define CONFIG_OS1_ENV_ADDR     __stringify(0xfef00000)
 371 #define CONFIG_OS2_ENV_ADDR     __stringify(0xf6f00000)
 372
 373 #define CONFIG_PROG_UBOOT1                                              \
 374         "$download_cmd $loadaddr $ubootfile; "                          \
 375         "if test $? -eq 0; then "                                       \
 376                 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "         \
 377                 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "               \
 378                 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "       \
 379                 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "          \
 380                 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "      \
 381                 "if test $? -ne 0; then "                               \
 382                         "echo PROGRAM FAILED; "                         \
 383                 "else; "                                                \
 384                         "echo PROGRAM SUCCEEDED; "                      \
 385                 "fi; "                                                  \
 386         "else; "                                                        \
 387                 "echo DOWNLOAD FAILED; "                                \
 388         "fi;"
 389
 390 #define CONFIG_PROG_UBOOT2                                              \
 391         "$download_cmd $loadaddr $ubootfile; "                          \
 392         "if test $? -eq 0; then "                                       \
 393                 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "         \
 394                 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "               \
 395                 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "       \
 396                 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "          \
 397                 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "      \
 398                 "if test $? -ne 0; then "                               \
 399                         "echo PROGRAM FAILED; "                         \
 400                 "else; "                                                \
 401                         "echo PROGRAM SUCCEEDED; "                      \
 402                 "fi; "                                                  \
 403         "else; "                                                        \
 404                 "echo DOWNLOAD FAILED; "                                \
 405         "fi;"
 406
 407 #define CONFIG_BOOT_OS_NET                                              \
 408         "$download_cmd $osaddr $osfile; "                               \
 409         "if test $? -eq 0; then "                                       \
 410                 "if test -n $fdtaddr; then "                            \
 411                         "$download_cmd $fdtaddr $fdtfile; "             \
 412                         "if test $? -eq 0; then "                       \
 413                                 "bootm $osaddr - $fdtaddr; "            \
 414                         "else; "                                        \
 415                                 "echo FDT DOWNLOAD FAILED; "            \
 416                         "fi; "                                          \
 417                 "else; "                                                \
 418                         "bootm $osaddr; "                               \
 419                 "fi; "                                                  \
 420         "else; "                                                        \
 421                 "echo OS DOWNLOAD FAILED; "                             \
 422         "fi;"
 423
 424 #define CONFIG_PROG_OS1                                                 \
 425         "$download_cmd $osaddr $osfile; "                               \
 426         "if test $? -eq 0; then "                                       \
 427                 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; "              \
 428                 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "        \
 429                 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "       \
 430                 "if test $? -ne 0; then "                               \
 431                         "echo OS PROGRAM FAILED; "                      \
 432                 "else; "                                                \
 433                         "echo OS PROGRAM SUCCEEDED; "                   \
 434                 "fi; "                                                  \
 435         "else; "                                                        \
 436                 "echo OS DOWNLOAD FAILED; "                             \
 437         "fi;"
 438
 439 #define CONFIG_PROG_OS2                                                 \
 440         "$download_cmd $osaddr $osfile; "                               \
 441         "if test $? -eq 0; then "                                       \
 442                 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; "              \
 443                 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "        \
 444                 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "       \
 445                 "if test $? -ne 0; then "                               \
 446                         "echo OS PROGRAM FAILED; "                      \
 447                 "else; "                                                \
 448                         "echo OS PROGRAM SUCCEEDED; "                   \
 449                 "fi; "                                                  \
 450         "else; "                                                        \
 451                 "echo OS DOWNLOAD FAILED; "                             \
 452         "fi;"
 453
 454 #define CONFIG_PROG_FDT1                                                \
 455         "$download_cmd $fdtaddr $fdtfile; "                             \
 456         "if test $? -eq 0; then "                                       \
 457                 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"              \
 458                 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "      \
 459                 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "     \
 460                 "if test $? -ne 0; then "                               \
 461                         "echo FDT PROGRAM FAILED; "                     \
 462                 "else; "                                                \
 463                         "echo FDT PROGRAM SUCCEEDED; "                  \
 464                 "fi; "                                                  \
 465         "else; "                                                        \
 466                 "echo FDT DOWNLOAD FAILED; "                            \
 467         "fi;"
 468
 469 #define CONFIG_PROG_FDT2                                                \
 470         "$download_cmd $fdtaddr $fdtfile; "                             \
 471         "if test $? -eq 0; then "                                       \
 472                 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"              \
 473                 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "      \
 474                 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "     \
 475                 "if test $? -ne 0; then "                               \
 476                         "echo FDT PROGRAM FAILED; "                     \
 477                 "else; "                                                \
 478                         "echo FDT PROGRAM SUCCEEDED; "                  \
 479                 "fi; "                                                  \
 480         "else; "                                                        \
 481                 "echo FDT DOWNLOAD FAILED; "                            \
 482         "fi;"
 483
 484 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 485         "autoload=yes\0"                                                \
 486         "download_cmd=tftp\0"                                           \
 487         "console_args=console=ttyS0,115200\0"                           \
 488         "root_args=root=/dev/nfs rw\0"                                  \
 489         "misc_args=ip=on\0"                                             \
 490         "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 491         "bootfile=/home/user/file\0"                                    \
 492         "osfile=/home/user/board.uImage\0"                              \
 493         "fdtfile=/home/user/board.dtb\0"                                \
 494         "ubootfile=/home/user/u-boot.bin\0"                             \
 495         "fdtaddr=0x1e00000\0"                                           \
 496         "osaddr=0x1000000\0"                                            \
 497         "loadaddr=0x1000000\0"                                          \
 498         "prog_uboot1="CONFIG_PROG_UBOOT1"\0"                            \
 499         "prog_uboot2="CONFIG_PROG_UBOOT2"\0"                            \
 500         "prog_os1="CONFIG_PROG_OS1"\0"                                  \
 501         "prog_os2="CONFIG_PROG_OS2"\0"                                  \
 502         "prog_fdt1="CONFIG_PROG_FDT1"\0"                                \
 503         "prog_fdt2="CONFIG_PROG_FDT2"\0"                                \
 504         "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"          \
 505         "bootcmd_flash1=run set_bootargs; "                             \
 506                 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
 507         "bootcmd_flash2=run set_bootargs; "                             \
 508                 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
 509         "bootcmd=run bootcmd_flash1\0"
 510 #endif  /* __CONFIG_H */