include/configs/xpedite517x.h

   1 /*
   2  * Copyright 2009 Extreme Engineering Solutions, Inc.
   3  * Copyright 2007-2008 Freescale Semiconductor, Inc.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * xpedite517x board configuration file
  10  */
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * High Level Configuration Options
  16  */
  17 #define CONFIG_SYS_BOARD_NAME   "XPedite5170"
  18 #define CONFIG_SYS_FORM_3U_VPX  1
  19 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
  20 #define CONFIG_BOARD_EARLY_INIT_R       /* Call board_pre_init */
  21 #define CONFIG_BAT_RW           1       /* Use common BAT rw code */
  22 #define CONFIG_HIGH_BATS        1       /* High BATs supported and enabled */
  23 #define CONFIG_ALTIVEC          1
  24
  25 #define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup */
  26 #define CONFIG_PCIE1            1       /* PCIE controller 1 */
  27 #define CONFIG_PCIE2            1       /* PCIE controller 2 */
  28 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  29 #define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
  30 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  31
  32 /*
  33  * DDR config
  34  */
  35 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
  36 #define CONFIG_DDR_SPD
  37 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  38 #define SPD_EEPROM_ADDRESS1             0x54    /* Both channels use the */
  39 #define SPD_EEPROM_ADDRESS2             0x54    /* same SPD data         */
  40 #define SPD_EEPROM_OFFSET               0x200   /* OFFSET of SPD in EEPROM */
  41 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  42 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  43 #define CONFIG_DDR_ECC
  44 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  45 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
  46 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  47 #define CONFIG_VERY_BIG_RAM
  48 #define CONFIG_SYS_MAX_DDR_BAT_SIZE     0x80000000      /* BAT mapping size */
  49
  50 /*
  51  * virtual address to be used for temporary mappings.  There
  52  * should be 128k free at this VA.
  53  */
  54 #define CONFIG_SYS_SCRATCH_VA   0xe0000000
  55
  56 #ifndef __ASSEMBLY__
  57 extern unsigned long get_board_sys_clk(unsigned long dummy);
  58 #endif
  59
  60 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0) /* sysclk for MPC86xx */
  61
  62 /*
  63  * L2CR setup
  64  */
  65 #define CONFIG_SYS_L2
  66 #define L2_INIT         0
  67 #define L2_ENABLE       (L2CR_L2E)
  68
  69 /*
  70  * Base addresses -- Note these are effective addresses where the
  71  * actual resources get mapped (not physical addresses)
  72  */
  73 #define CONFIG_SYS_CCSRBAR              0xef000000      /* relocated CCSRBAR */
  74 #define CONFIG_SYS_CCSRBAR_PHYS         CONFIG_SYS_CCSRBAR
  75 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  76 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH    0x0
  77 #define CONFIG_SYS_IMMR                 CONFIG_SYS_CCSRBAR
  78
  79 /*
  80  * Diagnostics
  81  */
  82 #define CONFIG_SYS_MEMTEST_START        0x10000000
  83 #define CONFIG_SYS_MEMTEST_END          0x20000000
  84 #define CONFIG_POST                     (CONFIG_SYS_POST_MEMORY |\
  85                                          CONFIG_SYS_POST_I2C)
  86 /* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */
  87 #define I2C_ADDR_IGNORE_LIST            {0x50}
  88
  89 /*
  90  * Memory map
  91  * 0x0000_0000  0x7fff_ffff     DDR                     2G Cacheable
  92  * 0x8000_0000  0xbfff_ffff     PCIe1 Mem               1G non-cacheable
  93  * 0xc000_0000  0xcfff_ffff     PCIe2 Mem               256M non-cacheable
  94  * 0xe000_0000  0xe7ff_ffff     SRAM/SSRAM/L1 Cache     128M non-cacheable
  95  * 0xe800_0000  0xe87f_ffff     PCIe1 IO                8M non-cacheable
  96  * 0xe880_0000  0xe8ff_ffff     PCIe2 IO                8M non-cacheable
  97  * 0xef00_0000  0xef0f_ffff     CCSR/IMMR               1M non-cacheable
  98  * 0xef80_0000  0xef8f_ffff     NAND Flash              1M non-cacheable
  99  * 0xf000_0000  0xf7ff_ffff     NOR Flash 2             128M non-cacheable
 100  * 0xf800_0000  0xffff_ffff     NOR Flash 1             128M non-cacheable
 101  */
 102
 103 #define CONFIG_SYS_LBC_LCRR             (LCRR_CLKDIV_4 | LCRR_EADC_3)
 104
 105 /*
 106  * NAND flash configuration
 107  */
 108 #define CONFIG_SYS_NAND_BASE            0xef800000
 109 #define CONFIG_SYS_NAND_BASE2           0xef840000      /* Unused at this time */
 110 #define CONFIG_SYS_NAND_BASE_LIST       {CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE2}
 111 #define CONFIG_SYS_MAX_NAND_DEVICE      2
 112 #define CONFIG_NAND_ACTL
 113 #define CONFIG_SYS_NAND_ACTL_ALE        (1 << 14)       /* C_LA14 */
 114 #define CONFIG_SYS_NAND_ACTL_CLE        (1 << 15)       /* C_LA15 */
 115 #define CONFIG_SYS_NAND_ACTL_NCE        0               /* NCE not controlled by ADDR */
 116 #define CONFIG_SYS_NAND_ACTL_DELAY      25
 117 #define CONFIG_JFFS2_NAND
 118
 119 /*
 120  * NOR flash configuration
 121  */
 122 #define CONFIG_SYS_FLASH_BASE           0xf8000000
 123 #define CONFIG_SYS_FLASH_BASE2          0xf0000000
 124 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
 125 #define CONFIG_SYS_MAX_FLASH_BANKS      2               /* number of banks */
 126 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
 127 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Flash Erase Timeout (ms) */
 128 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Flash Write Timeout (ms) */
 129 #define CONFIG_FLASH_CFI_DRIVER
 130 #define CONFIG_SYS_FLASH_CFI
 131 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 132 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST       { {0xfff00000, 0xc0000}, \
 133                                                   {0xf7f00000, 0xc0000} }
 134 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 135 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000      /* early monitor loc */
 136
 137 /*
 138  * Chip select configuration
 139  */
 140 /* NOR Flash 0 on CS0 */
 141 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE  |\
 142                                  BR_PS_16               |\
 143                                  BR_V)
 144 #define CONFIG_SYS_OR0_PRELIM   (OR_AM_128MB            |\
 145                                  OR_GPCM_CSNT           |\
 146                                  OR_GPCM_XACS           |\
 147                                  OR_GPCM_ACS_DIV2       |\
 148                                  OR_GPCM_SCY_8          |\
 149                                  OR_GPCM_TRLX           |\
 150                                  OR_GPCM_EHTR           |\
 151                                  OR_GPCM_EAD)
 152
 153 /* NOR Flash 1 on CS1 */
 154 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FLASH_BASE2 |\
 155                                  BR_PS_16               |\
 156                                  BR_V)
 157 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 158
 159 /* NAND flash on CS2 */
 160 #define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_NAND_BASE   |\
 161                                  BR_PS_8                |\
 162                                  BR_V)
 163 #define CONFIG_SYS_OR2_PRELIM   (OR_AM_256KB            |\
 164                                  OR_GPCM_BCTLD          |\
 165                                  OR_GPCM_CSNT           |\
 166                                  OR_GPCM_ACS_DIV4       |\
 167                                  OR_GPCM_SCY_4          |\
 168                                  OR_GPCM_TRLX           |\
 169                                  OR_GPCM_EHTR)
 170
 171 /* Optional NAND flash on CS3 */
 172 #define CONFIG_SYS_BR3_PRELIM   (CONFIG_SYS_NAND_BASE2  |\
 173                                  BR_PS_8                |\
 174                                  BR_V)
 175 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 176
 177 /*
 178  * Use L1 as initial stack
 179  */
 180 #define CONFIG_SYS_INIT_RAM_LOCK        1
 181 #define CONFIG_SYS_INIT_RAM_ADDR        0xe0000000
 182 #define CONFIG_SYS_INIT_RAM_SIZE                0x00004000
 183
 184 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 185 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 186
 187 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 KB for Mon */
 188 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserved for malloc */
 189
 190 /*
 191  * Serial Port
 192  */
 193 #define CONFIG_SYS_NS16550_SERIAL
 194 #define CONFIG_SYS_NS16550_REG_SIZE     1
 195 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 196 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 197 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 198 #define CONFIG_SYS_BAUDRATE_TABLE       \
 199         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 200 #define CONFIG_LOADS_ECHO               1       /* echo on for serial download */
 201 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 202
 203 /*
 204  * I2C
 205  */
 206 #define CONFIG_SYS_I2C
 207 #define CONFIG_SYS_I2C_FSL
 208 #define CONFIG_SYS_FSL_I2C_SPEED        100000
 209 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 210 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 211 #define CONFIG_SYS_FSL_I2C2_SPEED       100000
 212 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 213 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 214
 215 /* PEX8518 slave I2C interface */
 216 #define CONFIG_SYS_I2C_PEX8518_ADDR     0x70
 217
 218 /* I2C DS1631 temperature sensor */
 219 #define CONFIG_SYS_I2C_LM90_ADDR        0x4c
 220
 221 /* I2C EEPROM - AT24C128B */
 222 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x54
 223 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
 224 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
 225 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
 226
 227 /* I2C RTC */
 228 #define CONFIG_RTC_M41T11               1
 229 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 230 #define CONFIG_SYS_M41T11_BASE_YEAR     2000
 231
 232 /* GPIO */
 233 #define CONFIG_PCA953X
 234 #define CONFIG_SYS_I2C_PCA953X_ADDR0    0x18
 235 #define CONFIG_SYS_I2C_PCA953X_ADDR1    0x1c
 236 #define CONFIG_SYS_I2C_PCA953X_ADDR2    0x1e
 237 #define CONFIG_SYS_I2C_PCA953X_ADDR3    0x1f
 238 #define CONFIG_SYS_I2C_PCA953X_ADDR     CONFIG_SYS_I2C_PCA953X_ADDR0
 239 #define CONFIG_SYS_I2C_PCA9553_ADDR     0x62
 240
 241 /*
 242  * PU = pulled high, PD = pulled low
 243  * I = input, O = output, IO = input/output
 244  */
 245 /* PCA9557 @ 0x18*/
 246 #define CONFIG_SYS_PCA953X_C0_SER0_EN           0x01 /* PU; UART0 enable (1: enabled) */
 247 #define CONFIG_SYS_PCA953X_C0_SER0_MODE         0x02 /* PU; UART0 serial mode select */
 248 #define CONFIG_SYS_PCA953X_C0_SER1_EN           0x04 /* PU; UART1 enable (1: enabled) */
 249 #define CONFIG_SYS_PCA953X_C0_SER1_MODE         0x08 /* PU; UART1 serial mode select */
 250 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS     0x10 /* PU; Boot flash CS select */
 251 #define CONFIG_SYS_PCA953X_NVM_WP               0x20 /* PU; Set to 0 to enable NVM writing */
 252
 253 /* PCA9557 @ 0x1c*/
 254 #define CONFIG_SYS_PCA953X_XMC0_ROOT0           0x01 /* PU; Low if XMC is RC */
 255 #define CONFIG_SYS_PCA953X_PLUG_GPIO0           0x02 /* Samtec connector GPIO */
 256 #define CONFIG_SYS_PCA953X_XMC0_WAKE            0x04 /* PU; XMC wake */
 257 #define CONFIG_SYS_PCA953X_XMC0_BIST            0x08 /* PU; XMC built in self test */
 258 #define CONFIG_SYS_PCA953X_XMC_PRESENT          0x10 /* PU; Low if XMC module installed */
 259 #define CONFIG_SYS_PCA953X_PMC_PRESENT          0x20 /* PU; Low if PMC module installed */
 260 #define CONFIG_SYS_PCA953X_PMC0_MONARCH         0x40 /* PMC monarch mode enable */
 261 #define CONFIG_SYS_PCA953X_PMC0_EREADY          0x80 /* PU; PMC PCI eready */
 262
 263 /* PCA9557 @ 0x1e*/
 264 #define CONFIG_SYS_PCA953X_P0_GA0               0x01 /* PU; VPX Geographical address */
 265 #define CONFIG_SYS_PCA953X_P0_GA1               0x02 /* PU; VPX Geographical address */
 266 #define CONFIG_SYS_PCA953X_P0_GA2               0x04 /* PU; VPX Geographical address */
 267 #define CONFIG_SYS_PCA953X_P0_GA3               0x08 /* PU; VPX Geographical address */
 268 #define CONFIG_SYS_PCA953X_P0_GA4               0x10 /* PU; VPX Geographical address */
 269 #define CONFIG_SYS_PCA953X_P0_GAP               0x20 /* PU; VPX Geographical address parity */
 270 #define CONFIG_SYS_PCA953X_P1_SYSEN             0x80 /* PU; VPX P1 SYSCON */
 271
 272 /* PCA9557 @ 0x1f */
 273 #define CONFIG_SYS_PCA953X_VPX_GPIO0            0x01 /* PU; VPX P15 GPIO */
 274 #define CONFIG_SYS_PCA953X_VPX_GPIO1            0x02 /* PU; VPX P15 GPIO */
 275 #define CONFIG_SYS_PCA953X_VPX_GPIO2            0x04 /* PU; VPX P15 GPIO */
 276 #define CONFIG_SYS_PCA953X_VPX_GPIO3            0x08 /* PU; VPX P15 GPIO */
 277
 278 /*
 279  * General PCI
 280  * Memory space is mapped 1-1, but I/O space must start from 0.
 281  */
 282 /* PCIE1 - PEX8518 */
 283 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 284 #define CONFIG_SYS_PCIE1_MEM_PHYS       CONFIG_SYS_PCIE1_MEM_BUS
 285 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x40000000      /* 1G */
 286 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 287 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe8000000
 288 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000      /* 8M */
 289
 290 /* PCIE2 - VPX P1 */
 291 #define CONFIG_SYS_PCIE2_MEM_BUS        0xc0000000
 292 #define CONFIG_SYS_PCIE2_MEM_PHYS       CONFIG_SYS_PCIE2_MEM_BUS
 293 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000      /* 256M */
 294 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 295 #define CONFIG_SYS_PCIE2_IO_PHYS        0xe8800000
 296 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00800000      /* 8M */
 297
 298 /*
 299  * Networking options
 300  */
 301 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
 302 #define CONFIG_MII              1       /* MII PHY management */
 303 #define CONFIG_ETHPRIME         "eTSEC1"
 304
 305 #define CONFIG_TSEC1            1
 306 #define CONFIG_TSEC1_NAME       "eTSEC1"
 307 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 308 #define TSEC1_PHY_ADDR          1
 309 #define TSEC1_PHYIDX            0
 310 #define CONFIG_HAS_ETH0
 311
 312 #define CONFIG_TSEC2            1
 313 #define CONFIG_TSEC2_NAME       "eTSEC2"
 314 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 315 #define TSEC2_PHY_ADDR          2
 316 #define TSEC2_PHYIDX            0
 317 #define CONFIG_HAS_ETH1
 318
 319 /*
 320  * BAT mappings
 321  */
 322 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
 323 #define CONFIG_SYS_CCSR_DEFAULT_DBATL   (CONFIG_SYS_CCSRBAR_DEFAULT     |\
 324                                          BATL_PP_RW                     |\
 325                                          BATL_CACHEINHIBIT              |\
 326                                          BATL_GUARDEDSTORAGE)
 327 #define CONFIG_SYS_CCSR_DEFAULT_DBATU   (CONFIG_SYS_CCSRBAR_DEFAULT     |\
 328                                          BATU_BL_1M                     |\
 329                                          BATU_VS                        |\
 330                                          BATU_VP)
 331 #define CONFIG_SYS_CCSR_DEFAULT_IBATL   (CONFIG_SYS_CCSRBAR_DEFAULT     |\
 332                                          BATL_PP_RW                     |\
 333                                          BATL_CACHEINHIBIT)
 334 #define CONFIG_SYS_CCSR_DEFAULT_IBATU   CONFIG_SYS_CCSR_DEFAULT_DBATU
 335 #endif
 336
 337 /*
 338  * BAT0         2G      Cacheable, non-guarded
 339  * 0x0000_0000  2G      DDR
 340  */
 341 #define CONFIG_SYS_DBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 342 #define CONFIG_SYS_DBAT0U       (BATU_BL_2G | BATU_VS | BATU_VP)
 343 #define CONFIG_SYS_IBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 344 #define CONFIG_SYS_IBAT0U       CONFIG_SYS_DBAT0U
 345
 346 /*
 347  * BAT1         1G      Cache-inhibited, guarded
 348  * 0x8000_0000  1G      PCI-Express 1 Memory
 349  */
 350 #define CONFIG_SYS_DBAT1L       (CONFIG_SYS_PCIE1_MEM_PHYS      |\
 351                                  BATL_PP_RW                     |\
 352                                  BATL_CACHEINHIBIT              |\
 353                                  BATL_GUARDEDSTORAGE)
 354 #define CONFIG_SYS_DBAT1U       (CONFIG_SYS_PCIE1_MEM_PHYS      |\
 355                                  BATU_BL_1G                     |\
 356                                  BATU_VS                        |\
 357                                  BATU_VP)
 358 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_PCIE1_MEM_PHYS      |\
 359                                  BATL_PP_RW                     |\
 360                                  BATL_CACHEINHIBIT)
 361 #define CONFIG_SYS_IBAT1U       CONFIG_SYS_DBAT1U
 362
 363 /*
 364  * BAT2         512M    Cache-inhibited, guarded
 365  * 0xc000_0000  512M    PCI-Express 2 Memory
 366  */
 367 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_PCIE2_MEM_PHYS      |\
 368                                  BATL_PP_RW                     |\
 369                                  BATL_CACHEINHIBIT              |\
 370                                  BATL_GUARDEDSTORAGE)
 371 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_PCIE2_MEM_PHYS      |\
 372                                  BATU_BL_512M                   |\
 373                                  BATU_VS                        |\
 374                                  BATU_VP)
 375 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_PCIE2_MEM_PHYS      |\
 376                                  BATL_PP_RW                     |\
 377                                  BATL_CACHEINHIBIT)
 378 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 379
 380 /*
 381  * BAT3         1M      Cache-inhibited, guarded
 382  * 0xe000_0000  1M      CCSR
 383  */
 384 #define CONFIG_SYS_DBAT3L       (CONFIG_SYS_CCSRBAR             |\
 385                                  BATL_PP_RW                     |\
 386                                  BATL_CACHEINHIBIT              |\
 387                                  BATL_GUARDEDSTORAGE)
 388 #define CONFIG_SYS_DBAT3U       (CONFIG_SYS_CCSRBAR             |\
 389                                  BATU_BL_1M                     |\
 390                                  BATU_VS                        |\
 391                                  BATU_VP)
 392 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_CCSRBAR             |\
 393                                  BATL_PP_RW                     |\
 394                                  BATL_CACHEINHIBIT)
 395 #define CONFIG_SYS_IBAT3U       CONFIG_SYS_DBAT3U
 396
 397 /*
 398  * BAT4         32M     Cache-inhibited, guarded
 399  * 0xe200_0000  16M     PCI-Express 1 I/O
 400  * 0xe300_0000  16M     PCI-Express 2 I/0
 401  */
 402 #define CONFIG_SYS_DBAT4L       (CONFIG_SYS_PCIE1_IO_PHYS       |\
 403                                  BATL_PP_RW                     |\
 404                                  BATL_CACHEINHIBIT              |\
 405                                  BATL_GUARDEDSTORAGE)
 406 #define CONFIG_SYS_DBAT4U       (CONFIG_SYS_PCIE1_IO_PHYS       |\
 407                                  BATU_BL_32M                    |\
 408                                  BATU_VS                        |\
 409                                  BATU_VP)
 410 #define CONFIG_SYS_IBAT4L       (CONFIG_SYS_PCIE1_IO_PHYS       |\
 411                                  BATL_PP_RW                     |\
 412                                  BATL_CACHEINHIBIT)
 413 #define CONFIG_SYS_IBAT4U       CONFIG_SYS_DBAT4U
 414
 415 /*
 416  * BAT5         128K    Cacheable, non-guarded
 417  * 0xe400_1000  128K    Init RAM for stack in the CPU DCache (no backing memory)
 418  */
 419 #define CONFIG_SYS_DBAT5L       (CONFIG_SYS_INIT_RAM_ADDR       |\
 420                                  BATL_PP_RW                     |\
 421                                  BATL_MEMCOHERENCE)
 422 #define CONFIG_SYS_DBAT5U       (CONFIG_SYS_INIT_RAM_ADDR       |\
 423                                  BATU_BL_128K                   |\
 424                                  BATU_VS                        |\
 425                                  BATU_VP)
 426 #define CONFIG_SYS_IBAT5L       CONFIG_SYS_DBAT5L
 427 #define CONFIG_SYS_IBAT5U       CONFIG_SYS_DBAT5U
 428
 429 /*
 430  * BAT6         256M    Cache-inhibited, guarded
 431  * 0xf000_0000  256M    FLASH
 432  */
 433 #define CONFIG_SYS_DBAT6L       (CONFIG_SYS_FLASH_BASE2         |\
 434                                  BATL_PP_RW                     |\
 435                                  BATL_CACHEINHIBIT              |\
 436                                  BATL_GUARDEDSTORAGE)
 437 #define CONFIG_SYS_DBAT6U       (CONFIG_SYS_FLASH_BASE          |\
 438                                  BATU_BL_256M                   |\
 439                                  BATU_VS                        |\
 440                                  BATU_VP)
 441 #define CONFIG_SYS_IBAT6L       (CONFIG_SYS_FLASH_BASE          |\
 442                                  BATL_PP_RW                     |\
 443                                  BATL_MEMCOHERENCE)
 444 #define CONFIG_SYS_IBAT6U       CONFIG_SYS_DBAT6U
 445
 446 /* Map the last 1M of flash where we're running from reset */
 447 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY  |\
 448                                  BATL_PP_RW                     |\
 449                                  BATL_CACHEINHIBIT              |\
 450                                  BATL_GUARDEDSTORAGE)
 451 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE                   |\
 452                                  BATU_BL_1M                     |\
 453                                  BATU_VS                        |\
 454                                  BATU_VP)
 455 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY  |\
 456                                  BATL_PP_RW                     |\
 457                                  BATL_MEMCOHERENCE)
 458 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
 459
 460 /*
 461  * BAT7         64M     Cache-inhibited, guarded
 462  * 0xe800_0000  64K     NAND FLASH
 463  * 0xe804_0000  128K    DUART Registers
 464  */
 465 #define CONFIG_SYS_DBAT7L       (CONFIG_SYS_NAND_BASE           |\
 466                                  BATL_PP_RW                     |\
 467                                  BATL_CACHEINHIBIT              |\
 468                                  BATL_GUARDEDSTORAGE)
 469 #define CONFIG_SYS_DBAT7U       (CONFIG_SYS_NAND_BASE           |\
 470                                  BATU_BL_512K                   |\
 471                                  BATU_VS                        |\
 472                                  BATU_VP)
 473 #define CONFIG_SYS_IBAT7L       (CONFIG_SYS_NAND_BASE           |\
 474                                  BATL_PP_RW                     |\
 475                                  BATL_CACHEINHIBIT)
 476 #define CONFIG_SYS_IBAT7U       CONFIG_SYS_DBAT7U
 477
 478 /*
 479  * Miscellaneous configurable options
 480  */
 481 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 482 #define CONFIG_LOADADDR         0x1000000       /* default location for tftp and bootm */
 483 #define CONFIG_PREBOOT                          /* enable preboot variable */
 484 #define CONFIG_INTEGRITY                        /* support booting INTEGRITY OS */
 485
 486 /*
 487  * For booting Linux, the board info and command line data
 488  * have to be in the first 16 MB of memory, since this is
 489  * the maximum mapped by the Linux kernel during initialization.
 490  */
 491 #define CONFIG_SYS_BOOTMAPSZ    (16 << 20)      /* Initial Memory map for Linux*/
 492 #define CONFIG_SYS_BOOTM_LEN    (16 << 20)      /* Increase max gunzip size */
 493
 494 /*
 495  * Environment Configuration
 496  */
 497 #define CONFIG_ENV_SECT_SIZE    0x20000         /* 128k (one sector) for env */
 498 #define CONFIG_ENV_SIZE         0x8000
 499 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 500
 501 /*
 502  * Flash memory map:
 503  * fffc0000 - ffffffff  Pri FDT (256KB)
 504  * fff80000 - fffbffff  Pri U-Boot Environment (256 KB)
 505  * fff00000 - fff7ffff  Pri U-Boot (512 KB)
 506  * fef00000 - ffefffff  Pri OS image (16MB)
 507  * f8000000 - feefffff  Pri OS Use/Filesystem (111MB)
 508  *
 509  * f7fc0000 - f7ffffff  Sec FDT (256KB)
 510  * f7f80000 - f7fbffff  Sec U-Boot Environment (256 KB)
 511  * f7f00000 - f7f7ffff  Sec U-Boot (512 KB)
 512  * f6f00000 - f7efffff  Sec OS image (16MB)
 513  * f0000000 - f6efffff  Sec OS Use/Filesystem (111MB)
 514  */
 515 #define CONFIG_UBOOT1_ENV_ADDR  __stringify(0xfff00000)
 516 #define CONFIG_UBOOT2_ENV_ADDR  __stringify(0xf7f00000)
 517 #define CONFIG_FDT1_ENV_ADDR    __stringify(0xfffc0000)
 518 #define CONFIG_FDT2_ENV_ADDR    __stringify(0xf7fc0000)
 519 #define CONFIG_OS1_ENV_ADDR     __stringify(0xfef00000)
 520 #define CONFIG_OS2_ENV_ADDR     __stringify(0xf6f00000)
 521
 522 #define CONFIG_PROG_UBOOT1                                              \
 523         "$download_cmd $loadaddr $ubootfile; "                          \
 524         "if test $? -eq 0; then "                                       \
 525                 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; "         \
 526                 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; "               \
 527                 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; "       \
 528                 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; "          \
 529                 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; "      \
 530                 "if test $? -ne 0; then "                               \
 531                         "echo PROGRAM FAILED; "                         \
 532                 "else; "                                                \
 533                         "echo PROGRAM SUCCEEDED; "                      \
 534                 "fi; "                                                  \
 535         "else; "                                                        \
 536                 "echo DOWNLOAD FAILED; "                                \
 537         "fi;"
 538
 539 #define CONFIG_PROG_UBOOT2                                              \
 540         "$download_cmd $loadaddr $ubootfile; "                          \
 541         "if test $? -eq 0; then "                                       \
 542                 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; "         \
 543                 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; "               \
 544                 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; "       \
 545                 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; "          \
 546                 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; "      \
 547                 "if test $? -ne 0; then "                               \
 548                         "echo PROGRAM FAILED; "                         \
 549                 "else; "                                                \
 550                         "echo PROGRAM SUCCEEDED; "                      \
 551                 "fi; "                                                  \
 552         "else; "                                                        \
 553                 "echo DOWNLOAD FAILED; "                                \
 554         "fi;"
 555
 556 #define CONFIG_BOOT_OS_NET                                              \
 557         "$download_cmd $osaddr $osfile; "                               \
 558         "if test $? -eq 0; then "                                       \
 559                 "if test -n $fdtaddr; then "                            \
 560                         "$download_cmd $fdtaddr $fdtfile; "             \
 561                         "if test $? -eq 0; then "                       \
 562                                 "bootm $osaddr - $fdtaddr; "            \
 563                         "else; "                                        \
 564                                 "echo FDT DOWNLOAD FAILED; "            \
 565                         "fi; "                                          \
 566                 "else; "                                                \
 567                         "bootm $osaddr; "                               \
 568                 "fi; "                                                  \
 569         "else; "                                                        \
 570                 "echo OS DOWNLOAD FAILED; "                             \
 571         "fi;"
 572
 573 #define CONFIG_PROG_OS1                                                 \
 574         "$download_cmd $osaddr $osfile; "                               \
 575         "if test $? -eq 0; then "                                       \
 576                 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; "              \
 577                 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "        \
 578                 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; "       \
 579                 "if test $? -ne 0; then "                               \
 580                         "echo OS PROGRAM FAILED; "                      \
 581                 "else; "                                                \
 582                         "echo OS PROGRAM SUCCEEDED; "                   \
 583                 "fi; "                                                  \
 584         "else; "                                                        \
 585                 "echo OS DOWNLOAD FAILED; "                             \
 586         "fi;"
 587
 588 #define CONFIG_PROG_OS2                                                 \
 589         "$download_cmd $osaddr $osfile; "                               \
 590         "if test $? -eq 0; then "                                       \
 591                 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; "              \
 592                 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "        \
 593                 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; "       \
 594                 "if test $? -ne 0; then "                               \
 595                         "echo OS PROGRAM FAILED; "                      \
 596                 "else; "                                                \
 597                         "echo OS PROGRAM SUCCEEDED; "                   \
 598                 "fi; "                                                  \
 599         "else; "                                                        \
 600                 "echo OS DOWNLOAD FAILED; "                             \
 601         "fi;"
 602
 603 #define CONFIG_PROG_FDT1                                                \
 604         "$download_cmd $fdtaddr $fdtfile; "                             \
 605         "if test $? -eq 0; then "                                       \
 606                 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;"              \
 607                 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "      \
 608                 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; "     \
 609                 "if test $? -ne 0; then "                               \
 610                         "echo FDT PROGRAM FAILED; "                     \
 611                 "else; "                                                \
 612                         "echo FDT PROGRAM SUCCEEDED; "                  \
 613                 "fi; "                                                  \
 614         "else; "                                                        \
 615                 "echo FDT DOWNLOAD FAILED; "                            \
 616         "fi;"
 617
 618 #define CONFIG_PROG_FDT2                                                \
 619         "$download_cmd $fdtaddr $fdtfile; "                             \
 620         "if test $? -eq 0; then "                                       \
 621                 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;"              \
 622                 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "      \
 623                 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; "     \
 624                 "if test $? -ne 0; then "                               \
 625                         "echo FDT PROGRAM FAILED; "                     \
 626                 "else; "                                                \
 627                         "echo FDT PROGRAM SUCCEEDED; "                  \
 628                 "fi; "                                                  \
 629         "else; "                                                        \
 630                 "echo FDT DOWNLOAD FAILED; "                            \
 631         "fi;"
 632
 633 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 634         "autoload=yes\0"                                                \
 635         "download_cmd=tftp\0"                                           \
 636         "console_args=console=ttyS0,115200\0"                           \
 637         "root_args=root=/dev/nfs rw\0"                                  \
 638         "misc_args=ip=on\0"                                             \
 639         "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
 640         "bootfile=/home/user/file\0"                                    \
 641         "osfile=/home/user/board.uImage\0"                              \
 642         "fdtfile=/home/user/board.dtb\0"                                \
 643         "ubootfile=/home/user/u-boot.bin\0"                             \
 644         "fdtaddr=0x1e00000\0"                                           \
 645         "osaddr=0x1000000\0"                                            \
 646         "loadaddr=0x1000000\0"                                          \
 647         "prog_uboot1="CONFIG_PROG_UBOOT1"\0"                            \
 648         "prog_uboot2="CONFIG_PROG_UBOOT2"\0"                            \
 649         "prog_os1="CONFIG_PROG_OS1"\0"                                  \
 650         "prog_os2="CONFIG_PROG_OS2"\0"                                  \
 651         "prog_fdt1="CONFIG_PROG_FDT1"\0"                                \
 652         "prog_fdt2="CONFIG_PROG_FDT2"\0"                                \
 653         "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0"          \
 654         "bootcmd_flash1=run set_bootargs; "                             \
 655                 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
 656         "bootcmd_flash2=run set_bootargs; "                             \
 657                 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
 658         "bootcmd=run bootcmd_flash1\0"
 659 #endif  /* __CONFIG_H */