Kconfig: Finish migration of hashing commands
[platform/kernel/u-boot.git] / include / configs / woodburn_common.h
1 /*
2  * (C) Copyright 2011, Stefano Babic <sbabic@denx.de>
3  *
4  * (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
5  *
6  * Configuration for the woodburn board.
7  *
8  * SPDX-License-Identifier:     GPL-2.0+
9  */
10
11 #ifndef __WOODBURN_COMMON_CONFIG_H
12 #define __WOODBURN_COMMON_CONFIG_H
13
14 #include <asm/arch/imx-regs.h>
15
16  /* High Level Configuration Options */
17 #define CONFIG_MX35
18 #define CONFIG_MX35_HCLK_FREQ   24000000
19 #define CONFIG_SYS_FSL_CLK
20
21 #define CONFIG_SYS_DCACHE_OFF
22
23 #define CONFIG_MACH_TYPE                MACH_TYPE_FLEA3
24
25 /* This is required to setup the ESDC controller */
26
27 #define CONFIG_CMDLINE_TAG              /* enable passing of ATAGs */
28 #define CONFIG_REVISION_TAG
29 #define CONFIG_SETUP_MEMORY_TAGS
30 #define CONFIG_INITRD_TAG
31
32 /*
33  * Size of malloc() pool
34  */
35 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 1024 * 1024)
36
37 /*
38  * Hardware drivers
39  */
40 #define CONFIG_SYS_I2C
41 #define CONFIG_SYS_I2C_MXC
42 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
43 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
44 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
45 #define CONFIG_SYS_SPD_BUS_NUM          0
46 #define CONFIG_MXC_SPI
47 #define CONFIG_MXC_GPIO
48
49 /* PMIC Controller */
50 #define CONFIG_POWER
51 #define CONFIG_POWER_I2C
52 #define CONFIG_POWER_FSL
53 #define CONFIG_POWER_FSL_MC13892
54 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR    0x8
55 #define CONFIG_RTC_MC13XXX
56
57 /* mmc driver */
58 #define CONFIG_FSL_ESDHC
59 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
60 #define CONFIG_SYS_FSL_ESDHC_NUM        1
61
62 /*
63  * UART (console)
64  */
65 #define CONFIG_MXC_UART
66 #define CONFIG_MXC_UART_BASE    UART1_BASE
67
68 /* allow to overwrite serial and ethaddr */
69 #define CONFIG_ENV_OVERWRITE
70 #define CONFIG_CONS_INDEX       1
71
72 /*
73  * Command definition
74  */
75 #define CONFIG_BOOTP_SUBNETMASK
76 #define CONFIG_BOOTP_GATEWAY
77 #define CONFIG_BOOTP_DNS
78
79 #define CONFIG_CMD_NAND
80
81 #define CONFIG_MXC_GPIO
82
83 #define CONFIG_NET_RETRY_COUNT  100
84
85
86 #define CONFIG_LOADADDR         0x80800000      /* loadaddr env var */
87
88 /*
89  * Ethernet on SOC (FEC)
90  */
91 #define CONFIG_FEC_MXC
92 #define IMX_FEC_BASE    FEC_BASE_ADDR
93 #define CONFIG_PHYLIB
94 #define CONFIG_PHY_MICREL
95 #define CONFIG_FEC_MXC_PHYADDR  0x1
96
97 #define CONFIG_MII
98 #define CONFIG_DISCOVER_PHY
99
100 #define CONFIG_ARP_TIMEOUT      200UL
101
102 /*
103  * Miscellaneous configurable options
104  */
105 #define CONFIG_SYS_LONGHELP     /* undef to save memory */
106 #define CONFIG_CMDLINE_EDITING
107
108 #define CONFIG_AUTO_COMPLETE
109 #define CONFIG_SYS_CBSIZE       256     /* Console I/O Buffer Size */
110 /* Print Buffer Size */
111 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
112 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
113 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
114
115 #define CONFIG_SYS_MEMTEST_START        0       /* memtest works on */
116 #define CONFIG_SYS_MEMTEST_END          0x10000
117
118 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
119
120 /*
121  * Physical Memory Map
122  */
123 #define CONFIG_NR_DRAM_BANKS    1
124 #define PHYS_SDRAM_1            CSD0_BASE_ADDR
125 #define PHYS_SDRAM_1_SIZE       (256 * 1024 * 1024)
126
127 #define CONFIG_SYS_SDRAM_BASE           CSD0_BASE_ADDR
128
129 #define CONFIG_SYS_GBL_DATA_OFFSET      (LOW_LEVEL_SRAM_STACK - \
130                                                 IRAM_BASE_ADDR - \
131                                                 GENERATED_GBL_DATA_SIZE)
132 #define CONFIG_SYS_INIT_SP_ADDR         (IRAM_BASE_ADDR + \
133                                         CONFIG_SYS_GBL_DATA_OFFSET)
134
135 /*
136  * MTD Command for mtdparts
137  */
138 #define CONFIG_CMD_MTDPARTS
139 #define CONFIG_MTD_DEVICE
140 #define CONFIG_FLASH_CFI_MTD
141 #define CONFIG_MTD_PARTITIONS
142 #define MTDIDS_DEFAULT          "nand0=mxc_nand,nor0=physmap-flash.0"
143 #define MTDPARTS_DEFAULT        "mtdparts=mxc_nand:50m(root1)," \
144                                 "32m(rootfb)," \
145                                 "64m(pcache)," \
146                                 "64m(app1)," \
147                                 "10m(app2),-(spool);" \
148                                 "physmap-flash.0:512k(u-boot),64k(env1)," \
149                                 "64k(env2),3776k(kernel1),3776k(kernel2)"
150
151 /*
152  * FLASH and environment organization
153  */
154 #define CONFIG_SYS_FLASH_BASE           CS0_BASE_ADDR
155 #define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
156 #define CONFIG_SYS_MAX_FLASH_SECT 512   /* max number of sectors on one chip */
157 /* Monitor at beginning of flash */
158 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
159 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)
160
161 #define CONFIG_ENV_SECT_SIZE    (128 * 1024)
162 #define CONFIG_ENV_SIZE         CONFIG_ENV_SECT_SIZE
163
164 /* Address and size of Redundant Environment Sector     */
165 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
166 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
167
168 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
169                                 CONFIG_SYS_MONITOR_LEN)
170
171 #define CONFIG_ENV_IS_IN_FLASH
172
173 /*
174  * CFI FLASH driver setup
175  */
176 #define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
177 #define CONFIG_FLASH_CFI_DRIVER
178
179 /* A non-standard buffered write algorithm */
180 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       /* faster */
181 #define CONFIG_SYS_FLASH_PROTECTION     /* Use hardware sector protection */
182
183 /*
184  * NAND FLASH driver setup
185  */
186 #define CONFIG_NAND_MXC
187 #define CONFIG_NAND_MXC_V1_1
188 #define CONFIG_MXC_NAND_REGS_BASE       (NFC_BASE_ADDR)
189 #define CONFIG_SYS_MAX_NAND_DEVICE      1
190 #define CONFIG_SYS_NAND_BASE            (NFC_BASE_ADDR)
191 #define CONFIG_MXC_NAND_HWECC
192 #define CONFIG_SYS_NAND_LARGEPAGE
193
194 #if 0
195 #define CONFIG_MTD_DEBUG
196 #define CONFIG_MTD_DEBUG_VERBOSE        7
197 #endif
198 #define CONFIG_SYS_NAND_ONFI_DETECTION
199
200 /*
201  * Default environment and default scripts
202  * to update uboot and load kernel
203  */
204
205 #define CONFIG_HOSTNAME woodburn
206 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
207         "netdev=eth0\0"                                                 \
208         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
209                 "nfsroot=${serverip}:${rootpath}\0"                     \
210         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
211         "addip_sta=setenv bootargs ${bootargs} "                        \
212                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
213                 ":${hostname}:${netdev}:off panic=1\0"                  \
214         "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"               \
215         "addip=if test -n ${ipdyn};then run addip_dyn;"                 \
216                 "else run addip_sta;fi\0"       \
217         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
218         "addtty=setenv bootargs ${bootargs}"                            \
219                 " console=ttymxc0,${baudrate}\0"                        \
220         "addmisc=setenv bootargs ${bootargs} ${misc}\0"                 \
221         "loadaddr=80800000\0"                                           \
222         "kernel_addr_r=80800000\0"                                      \
223         "hostname=" __stringify(CONFIG_HOSTNAME) "\0"                   \
224         "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0"            \
225         "ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0"      \
226         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
227                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
228         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
229                 "bootm ${kernel_addr}\0"                                \
230         "net_nfs=tftp ${kernel_addr_r} ${bootfile}; "                   \
231                 "run nfsargs addip addtty addmtd addmisc;"              \
232                 "bootm ${kernel_addr_r}\0"                              \
233         "net_self_load=tftp ${kernel_addr_r} ${bootfile};"              \
234                 "tftp ${ramdisk_addr_r} ${ramdisk_file};\0"             \
235         "net_self=if run net_self_load;then "                           \
236                 "run ramargs addip addtty addmtd addmisc;"              \
237                 "bootm ${kernel_addr_r} ${ramdisk_addr_r};"             \
238                 "else echo Images not loades;fi\0"                      \
239         "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0"          \
240         "load=tftp ${loadaddr} ${u-boot}\0"                             \
241         "uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0"         \
242         "update=protect off ${uboot_addr} +80000;"                      \
243                 "erase ${uboot_addr} +80000;"                           \
244                 "cp.b ${loadaddr} ${uboot_addr} ${filesize}\0"          \
245         "upd=if run load;then echo Updating u-boot;if run update;"      \
246                 "then echo U-Boot updated;"                             \
247                         "else echo Error updating u-boot !;"            \
248                         "echo Board without bootloader !!;"             \
249                 "fi;"                                                   \
250                 "else echo U-Boot not downloaded..exiting;fi\0"         \
251         "bootcmd=run net_nfs\0"
252
253 #endif                          /* __CONFIG_H */