include/configs/warp7.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) 2016 NXP Semiconductors
   4  *
   5  * Configuration settings for the i.MX7S Warp board.
   6  */
   7
   8 #ifndef __WARP7_CONFIG_H
   9 #define __WARP7_CONFIG_H
  10
  11 #include "mx7_common.h"
  12 #include <imximage.h>
  13
  14 #define PHYS_SDRAM_SIZE                 SZ_512M
  15
  16 /*
  17  * If we have defined the OPTEE ram size and not OPTEE it means that we were
  18  * launched by OPTEE, because of that we shall skip all the low level
  19  * initialization since it was already done by ATF or OPTEE
  20  */
  21 #ifdef CONFIG_OPTEE_TZDRAM_SIZE
  22 #ifndef CONFIG_OPTEE
  23 #define CONFIG_SKIP_LOWLEVEL_INIT
  24 #endif
  25 #endif
  26
  27 /* Size of malloc() pool */
  28 #define CONFIG_SYS_MALLOC_LEN           (35 * SZ_1M)
  29
  30 /* MMC Config*/
  31 #define CONFIG_SYS_FSL_ESDHC_ADDR       USDHC3_BASE_ADDR
  32 #define CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE
  33 #define CONFIG_SYS_MMC_IMG_LOAD_PART    1
  34
  35 /* Switch on SERIAL_TAG */
  36 #define CONFIG_SERIAL_TAG
  37
  38 #define CONFIG_DFU_ENV_SETTINGS \
  39         "dfu_alt_info=boot raw 0x2 0x1000 mmcpart 1\0" \
  40
  41 #define CONFIG_EXTRA_ENV_SETTINGS \
  42         CONFIG_DFU_ENV_SETTINGS \
  43         "script=boot.scr\0" \
  44         "script_signed=boot.scr.imx-signed\0" \
  45         "image=zImage\0" \
  46         "console=ttymxc0\0" \
  47         "ethact=usb_ether\0" \
  48         "fdt_high=0xffffffff\0" \
  49         "initrd_high=0xffffffff\0" \
  50         "fdt_file=imx7s-warp.dtb\0" \
  51         "fdt_addr=" __stringify(CONFIG_SYS_FDT_ADDR)"\0" \
  52         "optee_addr=" __stringify(CONFIG_OPTEE_LOAD_ADDR)"\0" \
  53         "boot_fdt=try\0" \
  54         "ip_dyn=yes\0" \
  55         "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
  56         "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
  57         "rootpart=" __stringify(CONFIG_WARP7_ROOT_PART) "\0" \
  58         "finduuid=part uuid mmc 0:${rootpart} uuid\0" \
  59         "mmcargs=setenv bootargs console=${console},${baudrate} " \
  60                 "root=PARTUUID=${uuid} rootwait rw\0" \
  61         "ivt_offset=" __stringify(BOOTROM_IVT_HDR_OFFSET)"\0"\
  62         "warp7_auth_or_fail=hab_auth_img_or_fail ${hab_ivt_addr} ${filesize} 0;\0" \
  63         "do_bootscript_hab=" \
  64                 "if test ${hab_enabled} -eq 1; then " \
  65                         "setexpr hab_ivt_addr ${loadaddr} - ${ivt_offset}; " \
  66                         "setenv script ${script_signed}; " \
  67                         "load mmc ${mmcdev}:${mmcpart} ${hab_ivt_addr} ${script}; " \
  68                         "run warp7_auth_or_fail; " \
  69                         "run bootscript; "\
  70                 "fi;\0" \
  71         "loadbootscript=" \
  72                 "load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
  73         "bootscript=echo Running bootscript from mmc ...; " \
  74                 "source\0" \
  75         "loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
  76         "loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
  77         "mmcboot=echo Booting from mmc ...; " \
  78                 "run finduuid; " \
  79                 "run mmcargs; " \
  80                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
  81                         "if run loadfdt; then " \
  82                                 "bootz ${loadaddr} - ${fdt_addr}; " \
  83                         "else " \
  84                                 "if test ${boot_fdt} = try; then " \
  85                                         "bootz; " \
  86                                 "else " \
  87                                         "echo WARN: Cannot load the DT; " \
  88                                 "fi; " \
  89                         "fi; " \
  90                 "else " \
  91                         "bootz; " \
  92                 "fi;\0" \
  93
  94 #define CONFIG_BOOTCOMMAND \
  95            "mmc dev ${mmcdev};" \
  96            "mmc dev ${mmcdev}; if mmc rescan; then " \
  97                    "run do_bootscript_hab;" \
  98                    "if run loadbootscript; then " \
  99                            "run bootscript; " \
 100                    "else " \
 101                            "if run loadimage; then " \
 102                                    "run mmcboot; " \
 103                            "fi; " \
 104                    "fi; " \
 105            "fi"
 106
 107 #define CONFIG_SYS_MEMTEST_START        0x80000000
 108 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_MEMTEST_START + 0x20000000)
 109
 110 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 111 #define CONFIG_SYS_HZ                   1000
 112
 113 /* Physical Memory Map */
 114 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 115
 116 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 117 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 118 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 119
 120 #define CONFIG_SYS_INIT_SP_OFFSET \
 121         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 122 #define CONFIG_SYS_INIT_SP_ADDR \
 123         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 124
 125 /* I2C configs */
 126 #define CONFIG_SYS_I2C_MXC
 127 #define CONFIG_SYS_I2C_SPEED            100000
 128
 129 /* environment organization */
 130 #define CONFIG_ENV_SIZE                 SZ_8K
 131
 132 #define CONFIG_ENV_OFFSET               (8 * SZ_64K)
 133 #define CONFIG_SYS_FSL_USDHC_NUM        1
 134
 135 #define CONFIG_SYS_MMC_ENV_DEV          0
 136 #define CONFIG_SYS_MMC_ENV_PART         0
 137
 138 /* USB Configs */
 139 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 140
 141 #define CONFIG_MXC_USB_PORTSC           (PORT_PTS_UTMI | PORT_PTS_PTW)
 142 #define CONFIG_MXC_USB_FLAGS            0
 143 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 /* Only OTG1 port enabled */
 144
 145 #define CONFIG_IMX_THERMAL
 146
 147 #define CONFIG_USBD_HS
 148
 149 /* USB Device Firmware Update support */
 150 #define CONFIG_SYS_DFU_DATA_BUF_SIZE    SZ_16M
 151 #define DFU_DEFAULT_POLL_TIMEOUT        300
 152
 153 #define CONFIG_USBNET_DEV_ADDR          "de:ad:be:af:00:01"
 154
 155 /* Environment variable name to represent HAB enable state */
 156 #define HAB_ENABLED_ENVNAME             "hab_enabled"
 157
 158 #endif