2 * esd vme8349 U-Boot configuration file
3 * Copyright (c) 2008, 2009 esd gmbh Hannover Germany
5 * (C) Copyright 2006-2010
6 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
8 * reinhard.arlt@esd-electronics.de
9 * Based on the MPC8349EMDS config.
11 * SPDX-License-Identifier: GPL-2.0+
15 * vme8349 board configuration file.
21 #define CONFIG_DISPLAY_BOARDINFO
24 * Top level Makefile configuration choices
31 * High Level Configuration Options
33 #define CONFIG_E300 1 /* E300 Family */
34 #define CONFIG_MPC834x 1 /* MPC834x family */
35 #define CONFIG_MPC8349 1 /* MPC8349 specific */
36 #define CONFIG_VME8349 1 /* ESD VME8349 board specific */
38 #define CONFIG_SYS_TEXT_BASE 0xFFF00000
40 #define CONFIG_MISC_INIT_R
43 /* Don't enable PCI2 on vme834x - it doesn't exist physically. */
44 #undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
46 #define CONFIG_PCI_66M
48 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */
50 #define CONFIG_83XX_CLKIN 33000000 /* in Hz */
53 #ifndef CONFIG_SYS_CLK_FREQ
55 #define CONFIG_SYS_CLK_FREQ 66000000
56 #define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
58 #define CONFIG_SYS_CLK_FREQ 33000000
59 #define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1
63 #define CONFIG_SYS_IMMR 0xE0000000
65 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
66 #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
67 #define CONFIG_SYS_MEMTEST_END 0x00100000
72 #define CONFIG_DDR_ECC /* only for ECC DDR module */
73 #define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
74 #define CONFIG_SPD_EEPROM
75 #define SPD_EEPROM_ADDRESS 0x54
76 #define CONFIG_SYS_READ_SPD vme8349_read_spd
77 #define CONFIG_SYS_83XX_DDR_USES_CS0 /* esd; Fsl board uses CS2/CS3 */
80 * 32-bit data path mode.
82 * Please note that using this mode for devices with the real density of 64-bit
83 * effectively reduces the amount of available memory due to the effect of
84 * wrapping around while translating address to row/columns, for example in the
85 * 256MB module the upper 128MB get aliased with contents of the lower
86 * 128MB); normally this define should be used for devices with real 32-bit
89 #undef CONFIG_DDR_32BIT
91 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is sys memory*/
92 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
93 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
94 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
95 | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
96 #define CONFIG_DDR_2T_TIMING
97 #define CONFIG_SYS_DDRCDR (DDRCDR_DHC_EN \
103 * FLASH on the Local Bus
105 #define CONFIG_SYS_FLASH_CFI
106 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
108 #define CONFIG_SYS_FLASH_BASE 0xffc00000 /* start of FLASH */
109 #define CONFIG_SYS_FLASH_SIZE 4 /* flash size in MB */
110 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
111 BR_PS_16 | /* 16bit */ \
112 BR_MS_GPCM | /* MSEL = GPCM */ \
115 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
125 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
126 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_4MB)
128 #define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */
129 #define CONFIG_SYS_FLASH_SIZE 128 /* flash size in MB */
130 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
131 BR_PS_16 | /* 16bit */ \
132 BR_MS_GPCM | /* MSEL = GPCM */ \
135 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
145 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
146 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_128MB)
148 /* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
150 #define CONFIG_SYS_WINDOW1_BASE 0xf0000000
151 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_WINDOW1_BASE \
156 #define CONFIG_SYS_OR1_PRELIM (OR_AM_256KB \
159 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_WINDOW1_BASE
160 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_256KB)
162 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
163 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device*/
165 #undef CONFIG_SYS_FLASH_CHECKSUM
166 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase TO (ms) */
167 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO (ms) */
169 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
171 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
172 #define CONFIG_SYS_RAMBOOT
174 #undef CONFIG_SYS_RAMBOOT
177 #define CONFIG_SYS_INIT_RAM_LOCK 1
178 #define CONFIG_SYS_INIT_RAM_ADDR 0xF7000000 /* Initial RAM addr */
179 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* size */
181 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
182 GENERATED_GBL_DATA_SIZE)
183 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
185 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB */
186 #define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Malloc size */
189 * Local Bus LCRR and LBCR regs
190 * LCRR: no DLL bypass, Clock divider is 4
191 * External Local Bus rate is
192 * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
194 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
195 #define CONFIG_SYS_LBC_LBCR 0x00000000
197 #undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */
202 #define CONFIG_CONS_INDEX 1
203 #define CONFIG_SYS_NS16550_SERIAL
204 #define CONFIG_SYS_NS16550_REG_SIZE 1
205 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
207 #define CONFIG_SYS_BAUDRATE_TABLE \
208 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
210 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
211 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
213 #define CONFIG_CMDLINE_EDITING /* add command line history */
214 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */
217 #define CONFIG_SYS_I2C
218 #define CONFIG_SYS_I2C_FSL
219 #define CONFIG_SYS_FSL_I2C_SPEED 400000
220 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
221 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
222 #define CONFIG_SYS_FSL_I2C2_SPEED 400000
223 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
224 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
225 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
226 /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
228 #define CONFIG_SYS_I2C_8574_ADDR2 0x20 /* I2C1, PCF8574 */
231 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
232 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
233 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
234 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)
238 * Addresses are mapped 1-1.
240 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
241 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
242 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
243 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
244 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
245 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
246 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000
247 #define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
248 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
250 #define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
251 #define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
252 #define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
253 #define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
254 #define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
255 #define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
256 #define CONFIG_SYS_PCI2_IO_BASE 0x00000000
257 #define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
258 #define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
260 #if defined(CONFIG_PCI)
264 #if defined(PCI_64BIT)
272 #define CONFIG_PCI_PNP /* do pci plug-and-play */
274 #undef CONFIG_EEPRO100
277 #if !defined(CONFIG_PCI_PNP)
278 #define PCI_ENET0_IOADDR 0xFIXME
279 #define PCI_ENET0_MEMADDR 0xFIXME
280 #define PCI_IDSEL_NUMBER 0xFIXME
283 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
284 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
286 #endif /* CONFIG_PCI */
293 #define CONFIG_TSEC_ENET /* TSEC ethernet support */
296 #if defined(CONFIG_TSEC_ENET)
298 #define CONFIG_GMII /* MII PHY management */
300 #define CONFIG_TSEC1_NAME "TSEC0"
302 #define CONFIG_TSEC2_NAME "TSEC1"
303 #define CONFIG_PHY_M88E1111
304 #define TSEC1_PHY_ADDR 0x08
305 #define TSEC2_PHY_ADDR 0x10
306 #define TSEC1_PHYIDX 0
307 #define TSEC2_PHYIDX 0
308 #define TSEC1_FLAGS TSEC_GIGABIT
309 #define TSEC2_FLAGS TSEC_GIGABIT
311 /* Options are: TSEC[0-1] */
312 #define CONFIG_ETHPRIME "TSEC0"
314 #endif /* CONFIG_TSEC_ENET */
319 #ifndef CONFIG_SYS_RAMBOOT
320 #define CONFIG_ENV_IS_IN_FLASH
321 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0xc0000)
322 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
323 #define CONFIG_ENV_SIZE 0x2000
325 /* Address and size of Redundant Environment Sector */
326 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
327 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
330 #define CONFIG_SYS_NO_FLASH /* Flash is not usable now */
331 #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
332 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
333 #define CONFIG_ENV_SIZE 0x2000
336 #define CONFIG_LOADS_ECHO /* echo on for serial download */
337 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
342 #define CONFIG_BOOTP_BOOTFILESIZE
343 #define CONFIG_BOOTP_BOOTPATH
344 #define CONFIG_BOOTP_GATEWAY
345 #define CONFIG_BOOTP_HOSTNAME
348 * Command line configuration.
350 #define CONFIG_CMD_DATE
351 #define CONFIG_SYS_RTC_BUS_NUM 0x01
352 #define CONFIG_SYS_I2C_RTC_ADDR 0x32
353 #define CONFIG_RTC_RX8025
354 #define CONFIG_CMD_TSI148
356 #if defined(CONFIG_PCI)
357 #define CONFIG_CMD_PCI
360 #if defined(CONFIG_SYS_RAMBOOT)
361 #undef CONFIG_CMD_ENV
364 /* Pass Ethernet MAC to VxWorks */
365 #define CONFIG_SYS_VXWORKS_MAC_PTR 0x000043f0
367 #undef CONFIG_WATCHDOG /* watchdog disabled */
370 * Miscellaneous configurable options
372 #define CONFIG_SYS_LONGHELP /* undef to save memory */
373 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
375 #if defined(CONFIG_CMD_KGDB)
376 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
378 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
381 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
382 #define CONFIG_SYS_MAXARGS 16 /* max num of command args */
383 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buf Size */
386 * For booting Linux, the board info and command line data
387 * have to be in the first 256 MB of memory, since this is
388 * the maximum mapped by the Linux kernel during initialization.
390 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Init Memory map for Linux*/
392 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
394 #define CONFIG_SYS_HRCW_LOW (\
395 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
396 HRCWL_DDR_TO_SCB_CLK_1X1 |\
397 HRCWL_CSB_TO_CLKIN |\
399 HRCWL_CORE_TO_CSB_2X1)
401 #if defined(PCI_64BIT)
402 #define CONFIG_SYS_HRCW_HIGH (\
405 HRCWH_PCI1_ARBITER_ENABLE |\
406 HRCWH_PCI2_ARBITER_DISABLE |\
408 HRCWH_FROM_0X00000100 |\
409 HRCWH_BOOTSEQ_DISABLE |\
410 HRCWH_SW_WATCHDOG_DISABLE |\
411 HRCWH_ROM_LOC_LOCAL_16BIT |\
412 HRCWH_TSEC1M_IN_GMII |\
413 HRCWH_TSEC2M_IN_GMII)
415 #define CONFIG_SYS_HRCW_HIGH (\
418 HRCWH_PCI1_ARBITER_ENABLE |\
419 HRCWH_PCI2_ARBITER_ENABLE |\
421 HRCWH_FROM_0X00000100 |\
422 HRCWH_BOOTSEQ_DISABLE |\
423 HRCWH_SW_WATCHDOG_DISABLE |\
424 HRCWH_ROM_LOC_LOCAL_16BIT |\
425 HRCWH_TSEC1M_IN_GMII |\
426 HRCWH_TSEC2M_IN_GMII)
429 /* System IO Config */
430 #define CONFIG_SYS_SICRH 0
431 #define CONFIG_SYS_SICRL SICRL_LDP_A
433 #define CONFIG_SYS_HID0_INIT 0x000000000
434 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
435 HID0_ENABLE_INSTRUCTION_CACHE)
437 #define CONFIG_SYS_HID2 HID2_HBE
439 #define CONFIG_SYS_GPIO1_PRELIM
440 #define CONFIG_SYS_GPIO1_DIR 0x00100000
441 #define CONFIG_SYS_GPIO1_DAT 0x00100000
443 #define CONFIG_SYS_GPIO2_PRELIM
444 #define CONFIG_SYS_GPIO2_DIR 0x78900000
445 #define CONFIG_SYS_GPIO2_DAT 0x70100000
447 #define CONFIG_HIGH_BATS /* High BATs supported */
449 /* DDR @ 0x00000000 */
450 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
452 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
455 /* PCI @ 0x80000000 */
457 #define CONFIG_PCI_INDIRECT_BRIDGE
458 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW | \
460 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | \
462 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_RW | \
463 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
464 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | \
467 #define CONFIG_SYS_IBAT1L (0)
468 #define CONFIG_SYS_IBAT1U (0)
469 #define CONFIG_SYS_IBAT2L (0)
470 #define CONFIG_SYS_IBAT2U (0)
473 #ifdef CONFIG_MPC83XX_PCI2
474 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE | BATL_PP_RW | \
476 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE | BATU_BL_256M | \
478 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE | BATL_PP_RW | \
479 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
480 #define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE | BATU_BL_256M | \
483 #define CONFIG_SYS_IBAT3L (0)
484 #define CONFIG_SYS_IBAT3U (0)
485 #define CONFIG_SYS_IBAT4L (0)
486 #define CONFIG_SYS_IBAT4U (0)
489 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
490 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_RW | \
491 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
492 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | \
495 #define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_RW | BATL_MEMCOHERENCE)
496 #define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
498 #if (CONFIG_SYS_DDR_SIZE == 512)
499 #define CONFIG_SYS_IBAT7L (CONFIG_SYS_SDRAM_BASE+0x10000000 | \
500 BATL_PP_RW | BATL_MEMCOHERENCE)
501 #define CONFIG_SYS_IBAT7U (CONFIG_SYS_SDRAM_BASE+0x10000000 | \
502 BATU_BL_256M | BATU_VS | BATU_VP)
504 #define CONFIG_SYS_IBAT7L (0)
505 #define CONFIG_SYS_IBAT7U (0)
508 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
509 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
510 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
511 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
512 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
513 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
514 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
515 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
516 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
517 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
518 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
519 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
520 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
521 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
522 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
523 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
525 #if defined(CONFIG_CMD_KGDB)
526 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
530 * Environment Configuration
532 #define CONFIG_ENV_OVERWRITE
534 #if defined(CONFIG_TSEC_ENET)
535 #define CONFIG_HAS_ETH0
536 #define CONFIG_HAS_ETH1
539 #define CONFIG_HOSTNAME VME8349
540 #define CONFIG_ROOTPATH "/tftpboot/rootfs"
541 #define CONFIG_BOOTFILE "uImage"
543 #define CONFIG_LOADADDR 800000 /* def location for tftp and bootm */
545 #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
546 #undef CONFIG_BOOTARGS /* boot command will set bootargs */
548 #define CONFIG_BAUDRATE 9600
550 #define CONFIG_EXTRA_ENV_SETTINGS \
552 "hostname=vme8349\0" \
553 "nfsargs=setenv bootargs root=/dev/nfs rw " \
554 "nfsroot=${serverip}:${rootpath}\0" \
555 "ramargs=setenv bootargs root=/dev/ram rw\0" \
556 "addip=setenv bootargs ${bootargs} " \
557 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
558 ":${hostname}:${netdev}:off panic=1\0" \
559 "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
560 "flash_nfs=run nfsargs addip addtty;" \
561 "bootm ${kernel_addr}\0" \
562 "flash_self=run ramargs addip addtty;" \
563 "bootm ${kernel_addr} ${ramdisk_addr}\0" \
564 "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
566 "load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0" \
567 "update=protect off fff00000 fff3ffff; " \
568 "era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
569 "upd=run load update\0" \
571 "fdtfile=vme8349.dtb\0" \
574 #define CONFIG_NFSBOOTCOMMAND \
575 "setenv bootargs root=/dev/nfs rw " \
576 "nfsroot=$serverip:$rootpath " \
577 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
579 "console=$consoledev,$baudrate $othbootargs;" \
580 "tftp $loadaddr $bootfile;" \
581 "tftp $fdtaddr $fdtfile;" \
582 "bootm $loadaddr - $fdtaddr"
584 #define CONFIG_RAMBOOTCOMMAND \
585 "setenv bootargs root=/dev/ram rw " \
586 "console=$consoledev,$baudrate $othbootargs;" \
587 "tftp $ramdiskaddr $ramdiskfile;" \
588 "tftp $loadaddr $bootfile;" \
589 "tftp $fdtaddr $fdtfile;" \
590 "bootm $loadaddr $ramdiskaddr $fdtaddr"
592 #define CONFIG_BOOTCOMMAND "run flash_self"
595 int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
596 unsigned char *buffer, int len);
599 #endif /* __CONFIG_H */