include/configs/vf610twr.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2013 Freescale Semiconductor, Inc.
   4  *
   5  * Configuration settings for the Freescale Vybrid vf610twr board.
   6  */
   7
   8 #ifndef __CONFIG_H
   9 #define __CONFIG_H
  10
  11 #include <asm/arch/imx-regs.h>
  12 #include <linux/stringify.h>
  13
  14 #define CONFIG_SYS_FSL_CLK
  15
  16 /* NAND support */
  17
  18 #ifdef CONFIG_CMD_NAND
  19 #define CONFIG_SYS_MAX_NAND_DEVICE      1
  20 #define CONFIG_SYS_NAND_BASE            NFC_BASE_ADDR
  21
  22 /* Dynamic MTD partition support */
  23 #endif
  24
  25 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  26 #define CONFIG_SYS_FSL_ESDHC_NUM        1
  27
  28 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  29 #define CONFIG_FEC_XCV_TYPE             RMII
  30 #define CONFIG_FEC_MXC_PHYADDR          0
  31
  32 /* I2C Configs */
  33 #define CONFIG_SYS_SPD_BUS_NUM          0
  34
  35 /* We boot from the gfxRAM area of the OCRAM. */
  36 #define CONFIG_BOARD_SIZE_LIMIT         520192
  37
  38 /*
  39  * We do have 128MB of memory on the Vybrid Tower board. Leave the last
  40  * 16MB alone to avoid conflicts with Cortex-M4 firmwares running from
  41  * DDR3. Hence, limit the memory range for image processing to 112MB
  42  * using bootm_size. All of the following must be within this range.
  43  * We have the default load at 32MB into DDR (for the kernel), FDT at
  44  * 64MB and the ramdisk 512KB above that (allowing for hopefully never
  45  * seen large trees). This allows a reasonable split between ramdisk
  46  * and kernel size, where the ram disk can be a bit larger.
  47  */
  48 #define MEM_LAYOUT_ENV_SETTINGS \
  49         "bootm_size=0x07000000\0" \
  50         "loadaddr=0x82000000\0" \
  51         "kernel_addr_r=0x82000000\0" \
  52         "fdt_addr=0x84000000\0" \
  53         "fdt_addr_r=0x84000000\0" \
  54         "rdaddr=0x84080000\0" \
  55         "ramdisk_addr_r=0x84080000\0"
  56
  57 #define CONFIG_EXTRA_ENV_SETTINGS \
  58         MEM_LAYOUT_ENV_SETTINGS \
  59         "script=boot.scr\0" \
  60         "image=zImage\0" \
  61         "console=ttyLP1\0" \
  62         "fdt_file=vf610-twr.dtb\0" \
  63         "boot_fdt=try\0" \
  64         "ip_dyn=yes\0" \
  65         "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
  66         "mmcpart=1\0" \
  67         "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
  68         "update_sd_firmware_filename=u-boot.imx\0" \
  69         "update_sd_firmware=" \
  70                 "if test ${ip_dyn} = yes; then " \
  71                         "setenv get_cmd dhcp; " \
  72                 "else " \
  73                         "setenv get_cmd tftp; " \
  74                 "fi; " \
  75                 "if mmc dev ${mmcdev}; then "   \
  76                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
  77                                 "setexpr fw_sz ${filesize} / 0x200; " \
  78                                 "setexpr fw_sz ${fw_sz} + 1; "  \
  79                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
  80                         "fi; "  \
  81                 "fi\0" \
  82         "mmcargs=setenv bootargs console=${console},${baudrate} " \
  83                 "root=${mmcroot}\0" \
  84         "loadbootscript=" \
  85                 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
  86         "bootscript=echo Running bootscript from mmc ...; " \
  87                 "source\0" \
  88         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
  89         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
  90         "mmcboot=echo Booting from mmc ...; " \
  91                 "run mmcargs; " \
  92                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
  93                         "if run loadfdt; then " \
  94                                 "bootz ${loadaddr} - ${fdt_addr}; " \
  95                         "else " \
  96                                 "if test ${boot_fdt} = try; then " \
  97                                         "bootz; " \
  98                                 "else " \
  99                                         "echo WARN: Cannot load the DT; " \
 100                                 "fi; " \
 101                         "fi; " \
 102                 "else " \
 103                         "bootz; " \
 104                 "fi;\0" \
 105         "netargs=setenv bootargs console=${console},${baudrate} " \
 106                 "root=/dev/nfs " \
 107         "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 108                 "netboot=echo Booting from net ...; " \
 109                 "run netargs; " \
 110                 "if test ${ip_dyn} = yes; then " \
 111                         "setenv get_cmd dhcp; " \
 112                 "else " \
 113                         "setenv get_cmd tftp; " \
 114                 "fi; " \
 115                 "${get_cmd} ${image}; " \
 116                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 117                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 118                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 119                         "else " \
 120                                 "if test ${boot_fdt} = try; then " \
 121                                         "bootz; " \
 122                                 "else " \
 123                                         "echo WARN: Cannot load the DT; " \
 124                                 "fi; " \
 125                         "fi; " \
 126                 "else " \
 127                         "bootz; " \
 128                 "fi;\0"
 129
 130 /* Miscellaneous configurable options */
 131
 132 /* Physical memory map */
 133 #define PHYS_SDRAM                      (0x80000000)
 134 #define PHYS_SDRAM_SIZE                 (128 * 1024 * 1024)
 135
 136 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 137 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 138 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 139
 140 #define CONFIG_SYS_INIT_SP_OFFSET \
 141         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 142 #define CONFIG_SYS_INIT_SP_ADDR \
 143         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 144
 145 #ifdef CONFIG_ENV_IS_IN_NAND
 146 #define CONFIG_ENV_RANGE                (512 * 1024)
 147 #endif
 148
 149 #endif