include/configs/vexpress_aemv8a.h

   1 /*
   2  * Configuration for Versatile Express. Parts were derived from other ARM
   3  *   configurations.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __VEXPRESS_AEMV8A_H
   9 #define __VEXPRESS_AEMV8A_H
  10
  11 /* We use generic board and device manager for v8 Versatile Express */
  12 #define CONFIG_SYS_GENERIC_BOARD
  13
  14 #ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP
  15 #ifndef CONFIG_SEMIHOSTING
  16 #error CONFIG_TARGET_VEXPRESS64_BASE_FVP requires CONFIG_SEMIHOSTING
  17 #endif
  18 #define CONFIG_ARMV8_SWITCH_TO_EL1
  19 #endif
  20
  21 #define CONFIG_REMAKE_ELF
  22
  23 #define CONFIG_SUPPORT_RAW_INITRD
  24
  25 /* Cache Definitions */
  26 #define CONFIG_SYS_DCACHE_OFF
  27 #define CONFIG_SYS_ICACHE_OFF
  28
  29 #define CONFIG_IDENT_STRING             " vexpress_aemv8a"
  30 #define CONFIG_BOOTP_VCI_STRING         "U-boot.armv8.vexpress_aemv8a"
  31
  32 /* Link Definitions */
  33 #ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP
  34 /* ATF loads u-boot here for BASE_FVP model */
  35 #define CONFIG_SYS_TEXT_BASE            0x88000000
  36 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_SDRAM_BASE + 0x03f00000)
  37 #elif CONFIG_TARGET_VEXPRESS64_JUNO
  38 #define CONFIG_SYS_TEXT_BASE            0xe0000000
  39 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
  40 #else
  41 #error "Unknown board variant"
  42 #endif
  43
  44 /* Flat Device Tree Definitions */
  45 #define CONFIG_OF_LIBFDT
  46
  47 /* CS register bases for the original memory map. */
  48 #define V2M_PA_CS0                      0x00000000
  49 #define V2M_PA_CS1                      0x14000000
  50 #define V2M_PA_CS2                      0x18000000
  51 #define V2M_PA_CS3                      0x1c000000
  52 #define V2M_PA_CS4                      0x0c000000
  53 #define V2M_PA_CS5                      0x10000000
  54
  55 #define V2M_PERIPH_OFFSET(x)            (x << 16)
  56 #define V2M_SYSREGS                     (V2M_PA_CS3 + V2M_PERIPH_OFFSET(1))
  57 #define V2M_SYSCTL                      (V2M_PA_CS3 + V2M_PERIPH_OFFSET(2))
  58 #define V2M_SERIAL_BUS_PCI              (V2M_PA_CS3 + V2M_PERIPH_OFFSET(3))
  59
  60 #define V2M_BASE                        0x80000000
  61
  62 /* Common peripherals relative to CS7. */
  63 #define V2M_AACI                        (V2M_PA_CS3 + V2M_PERIPH_OFFSET(4))
  64 #define V2M_MMCI                        (V2M_PA_CS3 + V2M_PERIPH_OFFSET(5))
  65 #define V2M_KMI0                        (V2M_PA_CS3 + V2M_PERIPH_OFFSET(6))
  66 #define V2M_KMI1                        (V2M_PA_CS3 + V2M_PERIPH_OFFSET(7))
  67
  68 #ifdef CONFIG_TARGET_VEXPRESS64_JUNO
  69 #define V2M_UART0                       0x7ff80000
  70 #define V2M_UART1                       0x7ff70000
  71 #else /* Not Juno */
  72 #define V2M_UART0                       (V2M_PA_CS3 + V2M_PERIPH_OFFSET(9))
  73 #define V2M_UART1                       (V2M_PA_CS3 + V2M_PERIPH_OFFSET(10))
  74 #define V2M_UART2                       (V2M_PA_CS3 + V2M_PERIPH_OFFSET(11))
  75 #define V2M_UART3                       (V2M_PA_CS3 + V2M_PERIPH_OFFSET(12))
  76 #endif
  77
  78 #define V2M_WDT                         (V2M_PA_CS3 + V2M_PERIPH_OFFSET(15))
  79
  80 #define V2M_TIMER01                     (V2M_PA_CS3 + V2M_PERIPH_OFFSET(17))
  81 #define V2M_TIMER23                     (V2M_PA_CS3 + V2M_PERIPH_OFFSET(18))
  82
  83 #define V2M_SERIAL_BUS_DVI              (V2M_PA_CS3 + V2M_PERIPH_OFFSET(22))
  84 #define V2M_RTC                         (V2M_PA_CS3 + V2M_PERIPH_OFFSET(23))
  85
  86 #define V2M_CF                          (V2M_PA_CS3 + V2M_PERIPH_OFFSET(26))
  87
  88 #define V2M_CLCD                        (V2M_PA_CS3 + V2M_PERIPH_OFFSET(31))
  89
  90 /* System register offsets. */
  91 #define V2M_SYS_CFGDATA                 (V2M_SYSREGS + 0x0a0)
  92 #define V2M_SYS_CFGCTRL                 (V2M_SYSREGS + 0x0a4)
  93 #define V2M_SYS_CFGSTAT                 (V2M_SYSREGS + 0x0a8)
  94
  95 /* Generic Timer Definitions */
  96 #define COUNTER_FREQUENCY               (0x1800000)     /* 24MHz */
  97
  98 /* Generic Interrupt Controller Definitions */
  99 #ifdef CONFIG_GICV3
 100 #define GICD_BASE                       (0x2f000000)
 101 #define GICR_BASE                       (0x2f100000)
 102 #else
 103
 104 #ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP
 105 #define GICD_BASE                       (0x2f000000)
 106 #define GICC_BASE                       (0x2c000000)
 107 #elif CONFIG_TARGET_VEXPRESS64_JUNO
 108 #define GICD_BASE                       (0x2C010000)
 109 #define GICC_BASE                       (0x2C02f000)
 110 #else
 111 #error "Unknown board variant"
 112 #endif
 113 #endif /* !CONFIG_GICV3 */
 114
 115 /* Size of malloc() pool */
 116 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + (8 << 20))
 117
 118 /* Ethernet Configuration */
 119 #ifdef CONFIG_TARGET_VEXPRESS64_JUNO
 120 /* The real hardware Versatile express uses SMSC9118 */
 121 #define CONFIG_SMC911X                  1
 122 #define CONFIG_SMC911X_32_BIT           1
 123 #define CONFIG_SMC911X_BASE             (0x018000000)
 124 #else
 125 /* The Vexpress64 simulators use SMSC91C111 */
 126 #define CONFIG_SMC91111                 1
 127 #define CONFIG_SMC91111_BASE            (0x01A000000)
 128 #endif
 129
 130 /* PL011 Serial Configuration */
 131 #define CONFIG_BAUDRATE                 115200
 132 #define CONFIG_CONS_INDEX               0
 133 #define CONFIG_PL01X_SERIAL
 134 #define CONFIG_PL011_SERIAL
 135 #ifdef CONFIG_TARGET_VEXPRESS64_JUNO
 136 #define CONFIG_PL011_CLOCK              7273800
 137 #else
 138 #define CONFIG_PL011_CLOCK              24000000
 139 #endif
 140
 141 /* Command line configuration */
 142 #define CONFIG_MENU
 143 /*#define CONFIG_MENU_SHOW*/
 144 #define CONFIG_CMD_CACHE
 145 #define CONFIG_CMD_BDI
 146 #define CONFIG_CMD_BOOTI
 147 #define CONFIG_CMD_UNZIP
 148 #define CONFIG_CMD_DHCP
 149 #define CONFIG_CMD_PXE
 150 #define CONFIG_CMD_ENV
 151 #define CONFIG_CMD_IMI
 152 #define CONFIG_CMD_LOADB
 153 #define CONFIG_CMD_MEMORY
 154 #define CONFIG_CMD_MII
 155 #define CONFIG_CMD_PING
 156 #define CONFIG_CMD_SAVEENV
 157 #define CONFIG_CMD_RUN
 158 #define CONFIG_CMD_BOOTD
 159 #define CONFIG_CMD_ECHO
 160 #define CONFIG_CMD_SOURCE
 161 #define CONFIG_CMD_FAT
 162 #define CONFIG_DOS_PARTITION
 163
 164 /* BOOTP options */
 165 #define CONFIG_BOOTP_BOOTFILESIZE
 166 #define CONFIG_BOOTP_BOOTPATH
 167 #define CONFIG_BOOTP_GATEWAY
 168 #define CONFIG_BOOTP_HOSTNAME
 169 #define CONFIG_BOOTP_PXE
 170 #define CONFIG_BOOTP_PXE_CLIENTARCH     0x100
 171
 172 /* Miscellaneous configurable options */
 173 #define CONFIG_SYS_LOAD_ADDR            (V2M_BASE + 0x10000000)
 174
 175 /* Physical Memory Map */
 176 #define CONFIG_NR_DRAM_BANKS            1
 177 #define PHYS_SDRAM_1                    (V2M_BASE)      /* SDRAM Bank #1 */
 178 /* Top 16MB reserved for secure world use */
 179 #define DRAM_SEC_SIZE           0x01000000
 180 #define PHYS_SDRAM_1_SIZE       0x80000000 - DRAM_SEC_SIZE
 181 #define CONFIG_SYS_SDRAM_BASE   PHYS_SDRAM_1
 182
 183 /* Enable memtest */
 184 #define CONFIG_CMD_MEMTEST
 185 #define CONFIG_SYS_MEMTEST_START        PHYS_SDRAM_1
 186 #define CONFIG_SYS_MEMTEST_END          (PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE)
 187
 188 /* Initial environment variables */
 189 #ifdef CONFIG_TARGET_VEXPRESS64_JUNO
 190 /*
 191  * Defines where the kernel and FDT exist in NOR flash and where it will
 192  * be copied into DRAM
 193  */
 194 #define CONFIG_EXTRA_ENV_SETTINGS       \
 195                                 "kernel_name=Image\0"   \
 196                                 "kernel_addr=0x80000000\0" \
 197                                 "fdt_name=juno\0" \
 198                                 "fdt_addr=0x83000000\0" \
 199                                 "fdt_high=0xffffffffffffffff\0" \
 200                                 "initrd_high=0xffffffffffffffff\0" \
 201
 202 /* Assume we boot with root on the first partition of a USB stick */
 203 #define CONFIG_BOOTARGS         "console=ttyAMA0,115200n8 " \
 204                                 "root=/dev/sda1 rw " \
 205                                 "rootwait "\
 206                                 "earlyprintk=pl011,0x7ff80000 debug user_debug=31 "\
 207                                 "loglevel=9"
 208
 209 /* Copy the kernel and FDT to DRAM memory and boot */
 210 #define CONFIG_BOOTCOMMAND      "afs load ${kernel_name} ${kernel_addr} ; " \
 211                                 "afs load  ${fdt_name} ${fdt_addr} ; " \
 212                                 "fdt addr ${fdt_addr}; fdt resize; " \
 213                                 "booti ${kernel_addr} - ${fdt_addr}"
 214
 215 #define CONFIG_BOOTDELAY                1
 216
 217 #elif CONFIG_TARGET_VEXPRESS64_BASE_FVP
 218 #define CONFIG_EXTRA_ENV_SETTINGS       \
 219                                 "kernel_name=Image\0"           \
 220                                 "kernel_addr=0x80000000\0"      \
 221                                 "initrd_name=ramdisk.img\0"     \
 222                                 "initrd_addr=0x88000000\0"      \
 223                                 "fdt_name=devtree.dtb\0"        \
 224                                 "fdt_addr=0x83000000\0"         \
 225                                 "fdt_high=0xffffffffffffffff\0" \
 226                                 "initrd_high=0xffffffffffffffff\0"
 227
 228 #define CONFIG_BOOTARGS         "console=ttyAMA0 earlyprintk=pl011,"\
 229                                 "0x1c090000 debug user_debug=31 "\
 230                                 "loglevel=9"
 231
 232 #define CONFIG_BOOTCOMMAND      "smhload ${kernel_name} ${kernel_addr}; " \
 233                                 "smhload ${fdt_name} ${fdt_addr}; " \
 234                                 "smhload ${initrd_name} ${initrd_addr} initrd_end; " \
 235                                 "fdt addr ${fdt_addr}; fdt resize; " \
 236                                 "fdt chosen ${initrd_addr} ${initrd_end}; " \
 237                                 "booti $kernel_addr - $fdt_addr"
 238
 239 #define CONFIG_BOOTDELAY                1
 240
 241 #else
 242 #error "Unknown board variant"
 243 #endif
 244
 245 /* Do not preserve environment */
 246 #define CONFIG_ENV_IS_NOWHERE           1
 247 #define CONFIG_ENV_SIZE                 0x1000
 248
 249 /* Monitor Command Prompt */
 250 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 251 #define CONFIG_SYS_PROMPT               "VExpress64# "
 252 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 253                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 254 #define CONFIG_SYS_HUSH_PARSER
 255 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 256 #define CONFIG_SYS_LONGHELP
 257 #define CONFIG_CMDLINE_EDITING
 258 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 259
 260 /* Flash memory is available on the Juno board only */
 261 #ifndef CONFIG_TARGET_VEXPRESS64_JUNO
 262 #define CONFIG_SYS_NO_FLASH
 263 #else
 264 #define CONFIG_CMD_FLASH
 265 #define CONFIG_CMD_ARMFLASH
 266 #define CONFIG_SYS_FLASH_CFI            1
 267 #define CONFIG_FLASH_CFI_DRIVER         1
 268 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_32BIT
 269 #define CONFIG_SYS_FLASH_BASE           0x08000000
 270 #define CONFIG_SYS_FLASH_SIZE           0x04000000 /* 64 MiB */
 271 #define CONFIG_SYS_MAX_FLASH_BANKS      2
 272
 273 /* Timeout values in ticks */
 274 #define CONFIG_SYS_FLASH_ERASE_TOUT     (2 * CONFIG_SYS_HZ) /* Erase Timeout */
 275 #define CONFIG_SYS_FLASH_WRITE_TOUT     (2 * CONFIG_SYS_HZ) /* Write Timeout */
 276
 277 /* 255 0x40000 sectors + first or last sector may have 4 erase regions = 259 */
 278 #define CONFIG_SYS_MAX_FLASH_SECT       259             /* Max sectors */
 279 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* use buffered writes */
 280 #define CONFIG_SYS_FLASH_PROTECTION     /* The devices have real protection */
 281 #define CONFIG_SYS_FLASH_EMPTY_INFO     /* flinfo indicates empty blocks */
 282
 283 #endif
 284
 285 #endif /* __VEXPRESS_AEMV8A_H */