include/configs/verdin-imx8mm.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2020-2021 Toradex
   4  */
   5
   6 #ifndef __VERDIN_IMX8MM_H
   7 #define __VERDIN_IMX8MM_H
   8
   9 #include <asm/arch/imx-regs.h>
  10 #include <linux/sizes.h>
  11
  12 #define CONFIG_SYS_MONITOR_LEN          SZ_512K
  13 #define CONFIG_SYS_UBOOT_BASE   \
  14         (QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
  15
  16 #define CONFIG_SYS_BOOTM_LEN           SZ_64M
  17
  18 #ifdef CONFIG_SPL_BUILD
  19 /* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
  20 #define CONFIG_MALLOC_F_ADDR            0x930000
  21 /* For RAW image gives a error info not panic */
  22 #define CONFIG_SPL_ABORT_ON_RAW_IMAGE
  23 #endif
  24
  25 #define MEM_LAYOUT_ENV_SETTINGS \
  26         "fdt_addr_r=0x44000000\0" \
  27         "kernel_addr_r=0x42000000\0" \
  28         "ramdisk_addr_r=0x46400000\0" \
  29         "scriptaddr=0x46000000\0"
  30
  31 /* Enable Distro Boot */
  32 #ifndef CONFIG_SPL_BUILD
  33 #define BOOT_TARGET_DEVICES(func) \
  34         func(MMC, mmc, 1) \
  35         func(MMC, mmc, 0) \
  36         func(DHCP, dhcp, na)
  37 #include <config_distro_bootcmd.h>
  38 #else
  39 #define BOOTENV
  40 #endif
  41
  42 /* Initial environment variables */
  43 #define CONFIG_EXTRA_ENV_SETTINGS \
  44         BOOTENV \
  45         MEM_LAYOUT_ENV_SETTINGS \
  46         "bootcmd_mfg=fastboot 0\0" \
  47         "boot_file=Image\0" \
  48         "boot_script_dhcp=boot.scr\0" \
  49         "console=ttymxc0\0" \
  50         "fdt_addr=0x43000000\0" \
  51         "fdt_board=dev\0" \
  52         "initrd_addr=0x43800000\0" \
  53         "initrd_high=0xffffffffffffffff\0" \
  54         "setup=setenv setupargs console=${console},${baudrate} " \
  55                 "console=tty1 consoleblank=0 earlycon\0" \
  56         "update_uboot=askenv confirm Did you load flash.bin (y/N)?; " \
  57                 "if test \"$confirm\" = \"y\"; then " \
  58                 "setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt " \
  59                 "${blkcnt} / 0x200; mmc dev 0 1; mmc write ${loadaddr} 0x2 " \
  60                 "${blkcnt}; fi\0"
  61
  62 #define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
  63 #define CONFIG_SYS_INIT_RAM_SIZE        SZ_2M
  64
  65 #if defined(CONFIG_ENV_IS_IN_MMC)
  66 /* Environment in eMMC, before config block at the end of 1st "boot sector" */
  67 #endif
  68
  69 #define CONFIG_SYS_SDRAM_BASE           0x40000000
  70
  71 /* SDRAM configuration */
  72 #define PHYS_SDRAM                      0x40000000
  73 #define PHYS_SDRAM_SIZE                 SZ_2G /* 2GB DDR */
  74
  75 /* UART */
  76 #define CONFIG_MXC_UART_BASE            UART_BASE_ADDR(1)
  77
  78 /* ENET */
  79 #define CONFIG_FEC_MXC_PHYADDR          7
  80
  81 /* USB Configs */
  82 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  83 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  84 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  85
  86 #endif /* __VERDIN_IMX8MM_H */