include/configs/uniphier.h

   1 /*
   2  * Copyright (C) 2012-2015 Panasonic Corporation
   3  * Copyright (C) 2015      Socionext Inc.
   4  *   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 /* U-boot - Common settings for UniPhier Family */
  10
  11 #ifndef __CONFIG_UNIPHIER_COMMON_H__
  12 #define __CONFIG_UNIPHIER_COMMON_H__
  13
  14 #if defined(CONFIG_MACH_PH1_PRO4)
  15 #define CONFIG_DDR_NUM_CH0 2
  16 #define CONFIG_DDR_NUM_CH1 2
  17
  18 /* Physical start address of SDRAM */
  19 #define CONFIG_SDRAM0_BASE      0x80000000
  20 #define CONFIG_SDRAM0_SIZE      0x20000000
  21 #define CONFIG_SDRAM1_BASE      0xa0000000
  22 #define CONFIG_SDRAM1_SIZE      0x20000000
  23 #endif
  24
  25 #if defined(CONFIG_MACH_PH1_LD4)
  26 #define CONFIG_DDR_NUM_CH0 1
  27 #define CONFIG_DDR_NUM_CH1 1
  28
  29 /* Physical start address of SDRAM */
  30 #define CONFIG_SDRAM0_BASE      0x80000000
  31 #define CONFIG_SDRAM0_SIZE      0x10000000
  32 #define CONFIG_SDRAM1_BASE      0x90000000
  33 #define CONFIG_SDRAM1_SIZE      0x10000000
  34 #endif
  35
  36 #if defined(CONFIG_MACH_PH1_SLD8)
  37 #define CONFIG_DDR_NUM_CH0 1
  38 #define CONFIG_DDR_NUM_CH1 1
  39
  40 /* Physical start address of SDRAM */
  41 #define CONFIG_SDRAM0_BASE      0x80000000
  42 #define CONFIG_SDRAM0_SIZE      0x10000000
  43 #define CONFIG_SDRAM1_BASE      0x90000000
  44 #define CONFIG_SDRAM1_SIZE      0x10000000
  45 #endif
  46
  47 #define CONFIG_I2C_EEPROM
  48 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  10
  49
  50 /*
  51  * Support card address map
  52  */
  53 #if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
  54 # define CONFIG_SUPPORT_CARD_BASE       0x03f00000
  55 # define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
  56 # define CONFIG_SUPPORT_CARD_LED_BASE   (CONFIG_SUPPORT_CARD_BASE + 0x00090000)
  57 # define CONFIG_SUPPORT_CARD_UART_BASE  (CONFIG_SUPPORT_CARD_BASE + 0x000b0000)
  58 #endif
  59
  60 #if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
  61 # define CONFIG_SUPPORT_CARD_BASE       0x08000000
  62 # define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
  63 # define CONFIG_SUPPORT_CARD_LED_BASE   (CONFIG_SUPPORT_CARD_BASE + 0x00401630)
  64 # define CONFIG_SUPPORT_CARD_UART_BASE  (CONFIG_SUPPORT_CARD_BASE + 0x00200000)
  65 #endif
  66
  67 #ifdef CONFIG_SYS_NS16550_SERIAL
  68 #define CONFIG_SYS_NS16550
  69 #define CONFIG_SYS_NS16550_COM1         CONFIG_SUPPORT_CARD_UART_BASE
  70 #define CONFIG_SYS_NS16550_CLK          12288000
  71 #define CONFIG_SYS_NS16550_REG_SIZE     -2
  72 #endif
  73
  74 /* TODO: move to Kconfig and device tree */
  75 #if 0
  76 #define CONFIG_SYS_NS16550_SERIAL
  77 #endif
  78
  79 #define CONFIG_SMC911X
  80
  81 #define CONFIG_SMC911X_BASE             CONFIG_SUPPORT_CARD_ETHER_BASE
  82 #define CONFIG_SMC911X_32_BIT
  83
  84 /*-----------------------------------------------------------------------
  85  * MMU and Cache Setting
  86  *----------------------------------------------------------------------*/
  87
  88 /* Comment out the following to enable L1 cache */
  89 /* #define CONFIG_SYS_ICACHE_OFF */
  90 /* #define CONFIG_SYS_DCACHE_OFF */
  91
  92 #define CONFIG_SYS_CACHELINE_SIZE       32
  93
  94 /* Comment out the following to enable L2 cache */
  95 #define CONFIG_UNIPHIER_L2CACHE_ON
  96
  97 #define CONFIG_DISPLAY_CPUINFO
  98 #define CONFIG_DISPLAY_BOARDINFO
  99 #define CONFIG_MISC_INIT_F
 100 #define CONFIG_BOARD_EARLY_INIT_F
 101 #define CONFIG_BOARD_EARLY_INIT_R
 102 #define CONFIG_BOARD_LATE_INIT
 103
 104 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 105
 106 #define CONFIG_TIMESTAMP
 107
 108 /* FLASH related */
 109 #define CONFIG_MTD_DEVICE
 110
 111 /*
 112  * uncomment the following to disable FLASH related code.
 113  */
 114 /* #define CONFIG_SYS_NO_FLASH */
 115
 116 #define CONFIG_FLASH_CFI_DRIVER
 117 #define CONFIG_SYS_FLASH_CFI
 118
 119 #define CONFIG_SYS_MAX_FLASH_SECT       256
 120 #define CONFIG_SYS_MONITOR_BASE         0
 121 #define CONFIG_SYS_FLASH_BASE           0
 122
 123 /*
 124  * flash_toggle does not work for out supoort card.
 125  * We need to use flash_status_poll.
 126  */
 127 #define CONFIG_SYS_CFI_FLASH_STATUS_POLL
 128
 129 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 130
 131 #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2
 132
 133 /* serial console configuration */
 134 #define CONFIG_BAUDRATE                 115200
 135
 136 #define CONFIG_SYS_GENERIC_BOARD
 137
 138 #if !defined(CONFIG_SPL_BUILD)
 139 #define CONFIG_USE_ARCH_MEMSET
 140 #define CONFIG_USE_ARCH_MEMCPY
 141 #endif
 142
 143 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 144
 145 #define CONFIG_CMDLINE_EDITING          /* add command line history     */
 146 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size */
 147 /* Print Buffer Size */
 148 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 149 #define CONFIG_SYS_MAXARGS              16      /* max number of command */
 150 /* Boot Argument Buffer Size */
 151 #define CONFIG_SYS_BARGSIZE             (CONFIG_SYS_CBSIZE)
 152
 153 #define CONFIG_CONS_INDEX               1
 154
 155 /*
 156  * For NAND booting the environment is embedded in the U-Boot image. Please take
 157  * look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
 158  */
 159 /* #define CONFIG_ENV_IS_IN_NAND */
 160 #define CONFIG_ENV_IS_NOWHERE
 161 #define CONFIG_ENV_SIZE                         0x2000
 162 #define CONFIG_ENV_OFFSET                       0x0
 163 /* #define CONFIG_ENV_OFFSET_REDUND     (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */
 164
 165 /* Time clock 1MHz */
 166 #define CONFIG_SYS_TIMER_RATE                   1000000
 167
 168 /*
 169  * By default, ARP timeout is 5 sec.
 170  * The first ARP request does not seem to work.
 171  * So we need to retry ARP request anyway.
 172  * We want to shrink the interval until the second ARP request.
 173  */
 174 #define CONFIG_ARP_TIMEOUT      500UL  /* 0.5 msec */
 175
 176 #define CONFIG_SYS_MAX_NAND_DEVICE                      1
 177 #define CONFIG_SYS_NAND_MAX_CHIPS                       2
 178 #define CONFIG_SYS_NAND_ONFI_DETECTION
 179
 180 #define CONFIG_NAND_DENALI_ECC_SIZE                     1024
 181
 182 #define CONFIG_SYS_NAND_REGS_BASE                       0x68100000
 183 #define CONFIG_SYS_NAND_DATA_BASE                       0x68000000
 184
 185 #define CONFIG_SYS_NAND_BASE            (CONFIG_SYS_NAND_DATA_BASE + 0x10)
 186
 187 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 188 #define CONFIG_SYS_NAND_BAD_BLOCK_POS                   0
 189
 190 /* USB */
 191 #define CONFIG_USB_MAX_CONTROLLER_COUNT         2
 192 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      4
 193 #define CONFIG_CMD_FAT
 194 #define CONFIG_FAT_WRITE
 195 #define CONFIG_DOS_PARTITION
 196
 197 /* memtest works on */
 198 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE
 199 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_SDRAM_BASE + 0x01000000)
 200
 201 #define CONFIG_BOOTDELAY                        3
 202 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
 203 #define CONFIG_AUTOBOOT_KEYED                   1
 204 #define CONFIG_AUTOBOOT_PROMPT  \
 205         "Press SPACE to abort autoboot in %d seconds\n", bootdelay
 206 #define CONFIG_AUTOBOOT_DELAY_STR               "d"
 207 #define CONFIG_AUTOBOOT_STOP_STR                " "
 208
 209 /*
 210  * Network Configuration
 211  */
 212 #define CONFIG_ETHADDR                  00:21:83:24:00:00
 213 #define CONFIG_SERVERIP                 192.168.11.1
 214 #define CONFIG_IPADDR                   192.168.11.10
 215 #define CONFIG_GATEWAYIP                192.168.11.1
 216 #define CONFIG_NETMASK                  255.255.255.0
 217
 218 #define CONFIG_LOADADDR                 0x84000000
 219 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 220 #define CONFIG_BOOTFILE                 "fit.itb"
 221
 222 #define CONFIG_CMDLINE_EDITING          /* add command line history     */
 223
 224 #define CONFIG_BOOTCOMMAND              "run $bootmode"
 225
 226 #define CONFIG_ROOTPATH                 "/nfs/root/path"
 227 #define CONFIG_NFSBOOTCOMMAND                                           \
 228         "setenv bootargs $bootargs root=/dev/nfs rw "                   \
 229         "nfsroot=$serverip:$rootpath "                                  \
 230         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
 231         "tftpboot; bootm;"
 232
 233 #define CONFIG_BOOTARGS         " user_debug=0x1f init=/sbin/init"
 234
 235 #define CONFIG_EXTRA_ENV_SETTINGS               \
 236         "netdev=eth0\0"                         \
 237         "image_offset=0x00080000\0"             \
 238         "image_size=0x00f00000\0"               \
 239         "verify=n\0"                            \
 240         "nandupdate=nand erase 0 0x100000 &&"                           \
 241                    "tftpboot u-boot-spl.bin &&"                         \
 242                    "nand write $loadaddr 0 0x10000 &&"                  \
 243                    "tftpboot u-boot-dtb.img &&"                         \
 244                    "nand write $loadaddr 0x10000 0xf0000\0"             \
 245         "norboot=run add_default_bootargs &&"                           \
 246                 "bootm $image_offset\0"                                 \
 247         "nandboot=run add_default_bootargs &&"                          \
 248                  "nand read $loadaddr $image_offset $image_size &&"     \
 249                  "bootm\0"                                              \
 250         "add_default_bootargs=setenv bootargs $bootargs"                \
 251                 " console=ttyS0,$baudrate\0"                            \
 252
 253 /* Open Firmware flat tree */
 254 #define CONFIG_OF_LIBFDT
 255
 256 #define CONFIG_HAVE_ARM_SECURE
 257
 258 /* Memory Size & Mapping */
 259 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SDRAM0_BASE
 260
 261 #if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE >= CONFIG_SDRAM1_BASE
 262 /* Thre is no memory hole */
 263 #define CONFIG_NR_DRAM_BANKS            1
 264 #define CONFIG_SYS_SDRAM_SIZE   (CONFIG_SDRAM0_SIZE + CONFIG_SDRAM1_SIZE)
 265 #else
 266 #define CONFIG_NR_DRAM_BANKS            2
 267 #define CONFIG_SYS_SDRAM_SIZE   (CONFIG_SDRAM0_SIZE)
 268 #endif
 269
 270 #define CONFIG_SYS_TEXT_BASE            0x84000000
 271
 272 #if defined(CONFIG_MACH_PH1_LD4) || defined(CONFIG_MACH_PH1_SLD8)
 273 #define CONFIG_SPL_TEXT_BASE            0x00040000
 274 #endif
 275 #if defined(CONFIG_MACH_PH1_PRO4)
 276 #define CONFIG_SPL_TEXT_BASE            0x00100000
 277 #endif
 278
 279 #define CONFIG_SPL_STACK                (0x0ff08000)
 280 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_TEXT_BASE)
 281
 282 #define CONFIG_PANIC_HANG
 283
 284 #define CONFIG_SPL_FRAMEWORK
 285 #define CONFIG_SPL_SERIAL_SUPPORT
 286 #define CONFIG_SPL_NAND_SUPPORT
 287
 288 #define CONFIG_SPL_LIBCOMMON_SUPPORT    /* for mem_malloc_init */
 289 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 290
 291 #define CONFIG_SPL_BOARD_INIT
 292
 293 #define CONFIG_SYS_NAND_U_BOOT_OFFS             0x10000
 294
 295 #define CONFIG_SPL_MAX_FOOTPRINT                0x10000
 296
 297 #endif /* __CONFIG_UNIPHIER_COMMON_H__ */