include/configs/uniphier.h

   1 /*
   2  * Copyright (C) 2012-2015 Masahiro Yamada <yamada.masahiro@socionext.com>
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /* U-boot - Common settings for UniPhier Family */
   8
   9 #ifndef __CONFIG_UNIPHIER_COMMON_H__
  10 #define __CONFIG_UNIPHIER_COMMON_H__
  11
  12 #if defined(CONFIG_ARCH_UNIPHIER_PH1_SLD3)
  13 #define CONFIG_DDR_NUM_CH0 2
  14 #define CONFIG_DDR_NUM_CH1 1
  15 #define CONFIG_DDR_NUM_CH2 1
  16
  17 /* Physical start address of SDRAM */
  18 #define CONFIG_SDRAM0_BASE      0x80000000
  19 #define CONFIG_SDRAM0_SIZE      0x20000000
  20 #define CONFIG_SDRAM1_BASE      0xc0000000
  21 #define CONFIG_SDRAM1_SIZE      0x20000000
  22 #define CONFIG_SDRAM2_BASE      0xc0000000
  23 #define CONFIG_SDRAM2_SIZE      0x10000000
  24 #endif
  25
  26 #if defined(CONFIG_ARCH_UNIPHIER_PH1_LD4)
  27 #define CONFIG_DDR_NUM_CH0 1
  28 #define CONFIG_DDR_NUM_CH1 1
  29
  30 /* Physical start address of SDRAM */
  31 #define CONFIG_SDRAM0_BASE      0x80000000
  32 #define CONFIG_SDRAM0_SIZE      0x10000000
  33 #define CONFIG_SDRAM1_BASE      0x90000000
  34 #define CONFIG_SDRAM1_SIZE      0x10000000
  35 #endif
  36
  37 #if defined(CONFIG_ARCH_UNIPHIER_PH1_PRO4)
  38 #define CONFIG_DDR_NUM_CH0 2
  39 #define CONFIG_DDR_NUM_CH1 2
  40
  41 /* Physical start address of SDRAM */
  42 #define CONFIG_SDRAM0_BASE      0x80000000
  43 #define CONFIG_SDRAM0_SIZE      0x20000000
  44 #define CONFIG_SDRAM1_BASE      0xa0000000
  45 #define CONFIG_SDRAM1_SIZE      0x20000000
  46 #endif
  47
  48 #if defined(CONFIG_ARCH_UNIPHIER_PH1_SLD8)
  49 #define CONFIG_DDR_NUM_CH0 1
  50 #define CONFIG_DDR_NUM_CH1 1
  51
  52 /* Physical start address of SDRAM */
  53 #define CONFIG_SDRAM0_BASE      0x80000000
  54 #define CONFIG_SDRAM0_SIZE      0x10000000
  55 #define CONFIG_SDRAM1_BASE      0x90000000
  56 #define CONFIG_SDRAM1_SIZE      0x10000000
  57 #endif
  58
  59 #define CONFIG_I2C_EEPROM
  60 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  10
  61
  62 #ifdef CONFIG_SYS_NS16550_SERIAL
  63 #define CONFIG_SYS_NS16550
  64 #define CONFIG_SYS_NS16550_COM1         CONFIG_SUPPORT_CARD_UART_BASE
  65 #define CONFIG_SYS_NS16550_CLK          12288000
  66 #define CONFIG_SYS_NS16550_REG_SIZE     -2
  67 #endif
  68
  69 /* TODO: move to Kconfig and device tree */
  70 #if 0
  71 #define CONFIG_SYS_NS16550_SERIAL
  72 #endif
  73
  74 #define CONFIG_SMC911X
  75
  76 /* dummy: referenced by examples/standalone/smc911x_eeprom.c */
  77 #define CONFIG_SMC911X_BASE     0
  78 #define CONFIG_SMC911X_32_BIT
  79
  80 /*-----------------------------------------------------------------------
  81  * MMU and Cache Setting
  82  *----------------------------------------------------------------------*/
  83
  84 /* Comment out the following to enable L1 cache */
  85 /* #define CONFIG_SYS_ICACHE_OFF */
  86 /* #define CONFIG_SYS_DCACHE_OFF */
  87
  88 #define CONFIG_SYS_CACHELINE_SIZE       32
  89
  90 /* Comment out the following to enable L2 cache */
  91 #define CONFIG_UNIPHIER_L2CACHE_ON
  92
  93 #define CONFIG_DISPLAY_CPUINFO
  94 #define CONFIG_DISPLAY_BOARDINFO
  95 #define CONFIG_MISC_INIT_F
  96 #define CONFIG_BOARD_EARLY_INIT_F
  97 #define CONFIG_BOARD_EARLY_INIT_R
  98 #define CONFIG_BOARD_LATE_INIT
  99
 100 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 101
 102 #define CONFIG_TIMESTAMP
 103
 104 /* FLASH related */
 105 #define CONFIG_MTD_DEVICE
 106
 107 /*
 108  * uncomment the following to disable FLASH related code.
 109  */
 110 /* #define CONFIG_SYS_NO_FLASH */
 111
 112 #define CONFIG_FLASH_CFI_DRIVER
 113 #define CONFIG_SYS_FLASH_CFI
 114
 115 #define CONFIG_SYS_MAX_FLASH_SECT       256
 116 #define CONFIG_SYS_MONITOR_BASE         0
 117 #define CONFIG_SYS_FLASH_BASE           0
 118
 119 /*
 120  * flash_toggle does not work for out supoort card.
 121  * We need to use flash_status_poll.
 122  */
 123 #define CONFIG_SYS_CFI_FLASH_STATUS_POLL
 124
 125 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 126
 127 #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
 128
 129 /* serial console configuration */
 130 #define CONFIG_BAUDRATE                 115200
 131
 132 #define CONFIG_SYS_GENERIC_BOARD
 133
 134 #if !defined(CONFIG_SPL_BUILD)
 135 #define CONFIG_USE_ARCH_MEMSET
 136 #define CONFIG_USE_ARCH_MEMCPY
 137 #endif
 138
 139 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 140
 141 #define CONFIG_CMDLINE_EDITING          /* add command line history     */
 142 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size */
 143 /* Print Buffer Size */
 144 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 145 #define CONFIG_SYS_MAXARGS              16      /* max number of command */
 146 /* Boot Argument Buffer Size */
 147 #define CONFIG_SYS_BARGSIZE             (CONFIG_SYS_CBSIZE)
 148
 149 #define CONFIG_CONS_INDEX               1
 150
 151 /*
 152  * For NAND booting the environment is embedded in the U-Boot image. Please take
 153  * look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
 154  */
 155 /* #define CONFIG_ENV_IS_IN_NAND */
 156 #define CONFIG_ENV_IS_NOWHERE
 157 #define CONFIG_ENV_SIZE                         0x2000
 158 #define CONFIG_ENV_OFFSET                       0x0
 159 /* #define CONFIG_ENV_OFFSET_REDUND     (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */
 160
 161 /* Time clock 1MHz */
 162 #define CONFIG_SYS_TIMER_RATE                   1000000
 163
 164 /*
 165  * By default, ARP timeout is 5 sec.
 166  * The first ARP request does not seem to work.
 167  * So we need to retry ARP request anyway.
 168  * We want to shrink the interval until the second ARP request.
 169  */
 170 #define CONFIG_ARP_TIMEOUT      500UL  /* 0.5 msec */
 171
 172 #define CONFIG_SYS_MAX_NAND_DEVICE                      1
 173 #define CONFIG_SYS_NAND_MAX_CHIPS                       2
 174 #define CONFIG_SYS_NAND_ONFI_DETECTION
 175
 176 #define CONFIG_NAND_DENALI_ECC_SIZE                     1024
 177
 178 #ifdef CONFIG_ARCH_UNIPHIER_PH1_SLD3
 179 #define CONFIG_SYS_NAND_REGS_BASE                       0xf8100000
 180 #define CONFIG_SYS_NAND_DATA_BASE                       0xf8000000
 181 #else
 182 #define CONFIG_SYS_NAND_REGS_BASE                       0x68100000
 183 #define CONFIG_SYS_NAND_DATA_BASE                       0x68000000
 184 #endif
 185
 186 #define CONFIG_SYS_NAND_BASE            (CONFIG_SYS_NAND_DATA_BASE + 0x10)
 187
 188 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 189 #define CONFIG_SYS_NAND_BAD_BLOCK_POS                   0
 190
 191 /* USB */
 192 #define CONFIG_USB_MAX_CONTROLLER_COUNT         2
 193 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      4
 194 #define CONFIG_CMD_FAT
 195 #define CONFIG_FAT_WRITE
 196 #define CONFIG_DOS_PARTITION
 197
 198 /* memtest works on */
 199 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE
 200 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_SDRAM_BASE + 0x01000000)
 201
 202 #define CONFIG_BOOTDELAY                        3
 203 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
 204
 205 /*
 206  * Network Configuration
 207  */
 208 #define CONFIG_SERVERIP                 192.168.11.1
 209 #define CONFIG_IPADDR                   192.168.11.10
 210 #define CONFIG_GATEWAYIP                192.168.11.1
 211 #define CONFIG_NETMASK                  255.255.255.0
 212
 213 #define CONFIG_LOADADDR                 0x84000000
 214 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 215
 216 #define CONFIG_CMDLINE_EDITING          /* add command line history     */
 217
 218 #define CONFIG_BOOTCOMMAND              "run $bootmode"
 219
 220 #define CONFIG_ROOTPATH                 "/nfs/root/path"
 221 #define CONFIG_NFSBOOTCOMMAND                                           \
 222         "setenv bootargs $bootargs root=/dev/nfs rw "                   \
 223         "nfsroot=$serverip:$rootpath "                                  \
 224         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
 225         "tftpboot; bootm;"
 226
 227 #define CONFIG_BOOTARGS         " earlyprintk loglevel=8"
 228
 229 #ifdef CONFIG_FIT
 230 #define CONFIG_BOOTFILE                 "fitImage"
 231 #define LINUXBOOT_ENV_SETTINGS \
 232         "fit_addr=0x00100000\0" \
 233         "fit_addr_r=0x84100000\0" \
 234         "fit_size=0x00f00000\0" \
 235         "norboot=run add_default_bootargs &&" \
 236                 "setexpr fit_addr $nor_base + $fit_addr &&" \
 237                 "bootm $fit_addr\0" \
 238         "nandboot=run add_default_bootargs &&" \
 239                 "nand read $fit_addr_r $fit_addr $fit_size &&" \
 240                 "bootm $fit_addr_r\0" \
 241         "tftpboot=run add_default_bootargs &&" \
 242                 "tftpboot $fit_addr_r $bootfile &&" \
 243                 "bootm $fit_addr_r\0"
 244 #else
 245 #define CONFIG_BOOTFILE                 "uImage"
 246 #define LINUXBOOT_ENV_SETTINGS \
 247         "fdt_addr=0x00100000\0" \
 248         "fdt_addr_r=0x84100000\0" \
 249         "fdt_size=0x00008000\0" \
 250         "fdt_file=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
 251         "kernel_addr=0x00200000\0" \
 252         "kernel_addr_r=0x84200000\0" \
 253         "kernel_size=0x00800000\0" \
 254         "ramdisk_addr=0x00a00000\0" \
 255         "ramdisk_addr_r=0x84a00000\0" \
 256         "ramdisk_size=0x00600000\0" \
 257         "ramdisk_file=rootfs.cpio.uboot\0" \
 258         "norboot=run add_default_bootargs &&" \
 259                 "setexpr kernel_addr $nor_base + $kernel_addr &&" \
 260                 "setexpr ramdisk_addr $nor_base + $ramdisk_addr &&" \
 261                 "setexpr fdt_addr $nor_base + $fdt_addr &&" \
 262                 "bootm $kernel_addr $ramdisk_addr $fdt_addr\0" \
 263         "nandboot=run add_default_bootargs &&" \
 264                 "nand read $kernel_addr_r $kernel_addr $kernel_size &&" \
 265                 "nand read $ramdisk_addr_r $ramdisk_addr $ramdisk_size &&" \
 266                 "nand read $fdt_addr_r $fdt_addr $fdt_size &&" \
 267                 "bootm $kernel_addr_r $ramdisk_addr_r $fdt_addr_r\0" \
 268         "tftpboot=run add_default_bootargs &&" \
 269                 "tftpboot $kernel_addr_r $bootfile &&" \
 270                 "tftpboot $ramdisk_addr_r $ramdisk_file &&" \
 271                 "tftpboot $fdt_addr_r $fdt_file &&" \
 272                 "bootm $kernel_addr_r $ramdisk_addr_r $fdt_addr_r\0"
 273 #endif
 274
 275 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 276         "netdev=eth0\0"                                         \
 277         "verify=n\0"                                            \
 278         "norbase=0x42000000\0"                                  \
 279         "nandupdate=nand erase 0 0x00100000 &&"                 \
 280                 "tftpboot u-boot-spl-dtb.bin &&"                \
 281                 "nand write $loadaddr 0 0x00010000 &&"          \
 282                 "tftpboot u-boot-dtb.img &&"                    \
 283                 "nand write $loadaddr 0x00010000 0x000f0000\0"  \
 284         "add_default_bootargs=setenv bootargs $bootargs"        \
 285                 " console=ttyS0,$baudrate\0"                    \
 286         LINUXBOOT_ENV_SETTINGS
 287
 288 /* Open Firmware flat tree */
 289 #define CONFIG_OF_LIBFDT
 290
 291 #define CONFIG_SYS_SDRAM_BASE           0x80000000
 292 #define CONFIG_NR_DRAM_BANKS            2
 293
 294 #if defined(CONFIG_ARCH_UNIPHIER_PH1_SLD3) || \
 295         defined(CONFIG_ARCH_UNIPHIER_PH1_LD4) || \
 296         defined(CONFIG_ARCH_UNIPHIER_PH1_SLD8)
 297 #define CONFIG_SPL_TEXT_BASE            0x00040000
 298 #endif
 299 #if defined(CONFIG_ARCH_UNIPHIER_PH1_PRO4)
 300 #define CONFIG_SPL_TEXT_BASE            0x00100000
 301 #endif
 302
 303 #define CONFIG_SPL_STACK                (0x0ff08000)
 304 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_TEXT_BASE)
 305
 306 #define CONFIG_PANIC_HANG
 307
 308 #define CONFIG_SPL_FRAMEWORK
 309 #define CONFIG_SPL_SERIAL_SUPPORT
 310 #define CONFIG_SPL_NAND_SUPPORT
 311
 312 #define CONFIG_SPL_LIBCOMMON_SUPPORT    /* for mem_malloc_init */
 313 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 314
 315 #define CONFIG_SPL_BOARD_INIT
 316
 317 #define CONFIG_SYS_NAND_U_BOOT_OFFS             0x10000
 318
 319 #define CONFIG_SPL_MAX_FOOTPRINT                0x10000
 320
 321 #endif /* __CONFIG_UNIPHIER_COMMON_H__ */