include/configs/uniphier-common.h

   1 /*
   2  * Copyright (C) 2012-2014 Panasonic Corporation
   3  *   Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /* U-boot - Common settings for UniPhier Family */
   9
  10 #ifndef __CONFIG_UNIPHIER_COMMON_H__
  11 #define __CONFIG_UNIPHIER_COMMON_H__
  12
  13 #if defined(CONFIG_PFC_MICRO_SUPPORT_CARD) &&   \
  14                                 defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
  15 # error "Both CONFIG_PFC_MICRO_SUPPORT_CARD and CONFIG_DCC_MICRO_SUPPORT_CARD \
  16 are defined. Select only one of them."
  17 #endif
  18
  19 /*
  20  * Support card address map
  21  */
  22 #if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
  23 # define CONFIG_SUPPORT_CARD_BASE       0x03f00000
  24 # define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
  25 # define CONFIG_SUPPORT_CARD_LED_BASE   (CONFIG_SUPPORT_CARD_BASE + 0x00090000)
  26 # define CONFIG_SUPPORT_CARD_UART_BASE  (CONFIG_SUPPORT_CARD_BASE + 0x000b0000)
  27 #endif
  28
  29 #if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
  30 # define CONFIG_SUPPORT_CARD_BASE       0x08000000
  31 # define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
  32 # define CONFIG_SUPPORT_CARD_LED_BASE   (CONFIG_SUPPORT_CARD_BASE + 0x00401630)
  33 # define CONFIG_SUPPORT_CARD_UART_BASE  (CONFIG_SUPPORT_CARD_BASE + 0x00200000)
  34 #endif
  35
  36 #ifdef CONFIG_SYS_NS16550_SERIAL
  37 #define CONFIG_SYS_NS16550
  38 #define CONFIG_SYS_NS16550_COM1         CONFIG_SUPPORT_CARD_UART_BASE
  39 #define CONFIG_SYS_NS16550_CLK          12288000
  40 #define CONFIG_SYS_NS16550_REG_SIZE     -2
  41 #endif
  42
  43 #define CONFIG_SMC911X_BASE             CONFIG_SUPPORT_CARD_ETHER_BASE
  44 #define CONFIG_SMC911X_32_BIT
  45
  46 #define CONFIG_SYS_MALLOC_F_LEN  0x7000
  47
  48 /*-----------------------------------------------------------------------
  49  * MMU and Cache Setting
  50  *----------------------------------------------------------------------*/
  51
  52 /* Comment out the following to enable L1 cache */
  53 /* #define CONFIG_SYS_ICACHE_OFF */
  54 /* #define CONFIG_SYS_DCACHE_OFF */
  55
  56 /* Comment out the following to enable L2 cache */
  57 #define CONFIG_UNIPHIER_L2CACHE_ON
  58
  59 #define CONFIG_DISPLAY_CPUINFO
  60 #define CONFIG_DISPLAY_BOARDINFO
  61 #define CONFIG_BOARD_LATE_INIT
  62
  63 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
  64
  65 #define CONFIG_TIMESTAMP
  66
  67 /* FLASH related */
  68 #define CONFIG_MTD_DEVICE
  69
  70 /*
  71  * uncomment the following to disable FLASH related code.
  72  */
  73 /* #define CONFIG_SYS_NO_FLASH */
  74
  75 #define CONFIG_FLASH_CFI_DRIVER
  76 #define CONFIG_SYS_FLASH_CFI
  77
  78 #define CONFIG_SYS_MAX_FLASH_SECT       256
  79 #define CONFIG_SYS_MONITOR_BASE         0
  80 #define CONFIG_SYS_FLASH_BASE           0
  81
  82 /*
  83  * flash_toggle does not work for out supoort card.
  84  * We need to use flash_status_poll.
  85  */
  86 #define CONFIG_SYS_CFI_FLASH_STATUS_POLL
  87
  88 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
  89
  90 #if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
  91 # define CONFIG_SYS_MAX_FLASH_BANKS     1
  92 # define CONFIG_SYS_FLASH_BANKS_LIST    {0x00000000}
  93 # define CONFIG_SYS_FLASH_BANKS_SIZES   {0x02000000}
  94 #endif
  95
  96 #if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
  97 # define CONFIG_SYS_MAX_FLASH_BANKS     1
  98 # define CONFIG_SYS_FLASH_BANKS_LIST    {0x04000000}
  99 # define CONFIG_SYS_FLASH_BANKS_SIZES   {0x04000000}
 100 #endif
 101
 102 /* serial console configuration */
 103 #define CONFIG_BAUDRATE                 115200
 104
 105 #define CONFIG_SYS_GENERIC_BOARD
 106
 107 #if !defined(CONFIG_SPL_BUILD)
 108 #define CONFIG_USE_ARCH_MEMSET
 109 #define CONFIG_USE_ARCH_MEMCPY
 110 #endif
 111
 112 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 113
 114 #define CONFIG_CMDLINE_EDITING          /* add command line history     */
 115 #define CONFIG_SYS_HUSH_PARSER          /* use "hush" command parser */
 116 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size */
 117 /* Print Buffer Size */
 118 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 119 #define CONFIG_SYS_MAXARGS              16      /* max number of command */
 120 /* Boot Argument Buffer Size */
 121 #define CONFIG_SYS_BARGSIZE             (CONFIG_SYS_CBSIZE)
 122
 123 #define CONFIG_CONS_INDEX               1
 124
 125 /*
 126  * For NAND booting the environment is embedded in the U-Boot image. Please take
 127  * look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
 128  */
 129 /* #define CONFIG_ENV_IS_IN_NAND */
 130 #define CONFIG_ENV_IS_NOWHERE
 131 #define CONFIG_ENV_SIZE                         0x2000
 132 #define CONFIG_ENV_OFFSET                       0x0
 133 /* #define CONFIG_ENV_OFFSET_REDUND     (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */
 134
 135 /* Time clock 1MHz */
 136 #define CONFIG_SYS_TIMER_RATE                   1000000
 137
 138 /*
 139  * By default, ARP timeout is 5 sec.
 140  * The first ARP request does not seem to work.
 141  * So we need to retry ARP request anyway.
 142  * We want to shrink the interval until the second ARP request.
 143  */
 144 #define CONFIG_ARP_TIMEOUT      500UL  /* 0.5 msec */
 145
 146 /*
 147  * Command line configuration.
 148  */
 149 #include <config_cmd_default.h>
 150
 151 #define CONFIG_CMD_PING
 152 #define CONFIG_CMD_TIME
 153 #define CONFIG_CMD_NAND         /* NAND flash suppport */
 154
 155 #define CONFIG_SYS_MAX_NAND_DEVICE                      1
 156 #define CONFIG_SYS_NAND_MAX_CHIPS                       2
 157 #define CONFIG_SYS_NAND_ONFI_DETECTION
 158
 159 #define CONFIG_NAND_DENALI_ECC_SIZE                     1024
 160
 161 #define CONFIG_SYS_NAND_REGS_BASE                       0x68100000
 162 #define CONFIG_SYS_NAND_DATA_BASE                       0x68000000
 163
 164 #define CONFIG_SYS_NAND_BASE            (CONFIG_SYS_NAND_DATA_BASE + 0x10)
 165
 166 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 167 #define CONFIG_SYS_NAND_BAD_BLOCK_POS                   0
 168
 169 /* memtest works on */
 170 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE
 171 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_SDRAM_BASE + 0x01000000)
 172
 173 #define CONFIG_BOOTDELAY                        3
 174 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
 175 #define CONFIG_AUTOBOOT_KEYED                   1
 176 #define CONFIG_AUTOBOOT_PROMPT  \
 177         "Press SPACE to abort autoboot in %d seconds\n", bootdelay
 178 #define CONFIG_AUTOBOOT_DELAY_STR               "d"
 179 #define CONFIG_AUTOBOOT_STOP_STR                " "
 180
 181 /*
 182  * Network Configuration
 183  */
 184 #define CONFIG_ETHADDR                  00:21:83:24:00:00
 185 #define CONFIG_SERVERIP                 192.168.11.1
 186 #define CONFIG_IPADDR                   192.168.11.10
 187 #define CONFIG_GATEWAYIP                192.168.11.1
 188 #define CONFIG_NETMASK                  255.255.255.0
 189
 190 #define CONFIG_LOADADDR                 0x84000000
 191 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 192 #define CONFIG_BOOTFILE                 "fit.itb"
 193
 194 #define CONFIG_CMDLINE_EDITING          /* add command line history     */
 195
 196 #define CONFIG_BOOTCOMMAND              "run $bootmode"
 197
 198 #define CONFIG_ROOTPATH                 "/nfs/root/path"
 199 #define CONFIG_NFSBOOTCOMMAND                                           \
 200         "setenv bootargs $bootargs root=/dev/nfs rw "                   \
 201         "nfsroot=$serverip:$rootpath "                                  \
 202         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
 203         "tftpboot; bootm;"
 204
 205 #define CONFIG_BOOTARGS         " user_debug=0x1f init=/sbin/init"
 206
 207 #define CONFIG_EXTRA_ENV_SETTINGS               \
 208         "netdev=eth0\0"                         \
 209         "image_offset=0x00080000\0"             \
 210         "image_size=0x00f00000\0"               \
 211         "verify=n\0"                            \
 212         "autostart=yes\0"                       \
 213         "norboot=run add_default_bootargs;"                             \
 214                 "bootm $image_offset\0"                                 \
 215         "nandboot=run add_default_bootargs;"                            \
 216                 "nand read $loadaddr $image_offset $image_size;"        \
 217                 "bootm\0"                                               \
 218         "add_default_bootargs=setenv bootargs $bootargs"                \
 219                 " console=ttyS0,$baudrate\0"                            \
 220
 221 /* FIT support */
 222 #define CONFIG_FIT
 223 #define CONFIG_FIT_VERBOSE      1 /* enable fit_format_{error,warning}() */
 224
 225 /* Open Firmware flat tree */
 226 #define CONFIG_OF_LIBFDT
 227
 228 #define CONFIG_HAVE_ARM_SECURE
 229
 230 /* Memory Size & Mapping */
 231 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SDRAM0_BASE
 232
 233 #if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE >= CONFIG_SDRAM1_BASE
 234 /* Thre is no memory hole */
 235 #define CONFIG_NR_DRAM_BANKS            1
 236 #define CONFIG_SYS_SDRAM_SIZE   (CONFIG_SDRAM0_SIZE + CONFIG_SDRAM1_SIZE)
 237 #else
 238 #define CONFIG_NR_DRAM_BANKS            2
 239 #define CONFIG_SYS_SDRAM_SIZE   (CONFIG_SDRAM0_SIZE)
 240 #endif
 241
 242 #define CONFIG_SYS_TEXT_BASE            0x84000000
 243
 244 #if defined(CONFIG_SPL_BUILD)
 245 #define CONFIG_BOARD_POSTCLK_INIT
 246 #else
 247 #define CONFIG_SKIP_LOWLEVEL_INIT
 248 #endif
 249
 250 #define CONFIG_SYS_SPL_MALLOC_START     (0x0ff00000)
 251 #define CONFIG_SYS_SPL_MALLOC_SIZE      (0x00004000)
 252
 253 #define CONFIG_SYS_INIT_SP_ADDR         (0x0ff08000)
 254
 255 #define CONFIG_SPL_FRAMEWORK
 256 #define CONFIG_SPL_NAND_SUPPORT
 257
 258 #define CONFIG_SPL_LIBCOMMON_SUPPORT    /* for mem_malloc_init */
 259 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 260
 261 #define CONFIG_SPL_BOARD_INIT
 262
 263 #define CONFIG_SYS_NAND_U_BOOT_OFFS             0x10000
 264
 265 #endif /* __CONFIG_UNIPHIER_COMMON_H__ */