include/configs/tricorder.h

   1 /*
   2  * (C) Copyright 2006-2008
   3  * Texas Instruments.
   4  * Richard Woodruff <r-woodruff2@ti.com>
   5  * Syed Mohammed Khasim <x0khasim@ti.com>
   6  *
   7  * (C) Copyright 2012
   8  * Corscience GmbH & Co. KG
   9  * Thomas Weber <weber@corscience.de>
  10  *
  11  * Configuration settings for the Tricorder board.
  12  *
  13  * SPDX-License-Identifier:     GPL-2.0+
  14  */
  15
  16 #ifndef __CONFIG_H
  17 #define __CONFIG_H
  18
  19 /* High Level Configuration Options */
  20 #define CONFIG_SYS_THUMB_BUILD
  21 #define CONFIG_OMAP                     /* in a TI OMAP core */
  22
  23 #define CONFIG_MACH_TYPE                MACH_TYPE_TRICORDER
  24 /*
  25  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
  26  * 64 bytes before this address should be set aside for u-boot.img's
  27  * header. That is 0x800FFFC0--0x80100000 should not be used for any
  28  * other needs.
  29  */
  30 #define CONFIG_SYS_TEXT_BASE            0x80100000
  31
  32 #define CONFIG_SDRC                     /* The chip has SDRC controller */
  33
  34 #include <asm/arch/cpu.h>               /* get chip and board defs */
  35 #include <asm/arch/omap.h>
  36
  37 /* Clock Defines */
  38 #define V_OSCK                          26000000 /* Clock output from T2 */
  39 #define V_SCLK                          (V_OSCK >> 1)
  40
  41 #define CONFIG_MISC_INIT_R
  42
  43 #define CONFIG_CMDLINE_TAG              /* enable passing of ATAGs */
  44 #define CONFIG_SETUP_MEMORY_TAGS
  45 #define CONFIG_INITRD_TAG
  46 #define CONFIG_REVISION_TAG
  47
  48 /* Size of malloc() pool */
  49 #define CONFIG_SYS_MALLOC_LEN           (1024*1024)
  50
  51 /* Hardware drivers */
  52
  53 /* GPIO support */
  54 #define CONFIG_OMAP_GPIO
  55
  56 /* GPIO banks */
  57 #define CONFIG_OMAP3_GPIO_2             /* GPIO32..63 are in GPIO bank 2 */
  58
  59 /* LED support */
  60
  61 /* NS16550 Configuration */
  62 #define CONFIG_SYS_NS16550_SERIAL
  63 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
  64 #define CONFIG_SYS_NS16550_CLK          48000000 /* 48MHz (APLL96/2) */
  65
  66 /* select serial console configuration */
  67 #define CONFIG_CONS_INDEX               3
  68 #define CONFIG_SYS_NS16550_COM3         OMAP34XX_UART3
  69 #define CONFIG_SERIAL3                  3
  70 #define CONFIG_BAUDRATE                 115200
  71 #define CONFIG_SYS_BAUDRATE_TABLE       {4800, 9600, 19200, 38400, 57600,\
  72                                         115200}
  73
  74 /* I2C */
  75 #define CONFIG_SYS_I2C
  76 #define CONFIG_SYS_OMAP24_I2C_SPEED     100000
  77 #define CONFIG_SYS_OMAP24_I2C_SLAVE     1
  78 #define CONFIG_SYS_I2C_OMAP34XX
  79
  80
  81 /* EEPROM */
  82 #define CONFIG_CMD_EEPROM
  83 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
  84 #define CONFIG_SYS_EEPROM_BUS_NUM       1
  85
  86 /* TWL4030 */
  87 #define CONFIG_TWL4030_POWER
  88 #define CONFIG_TWL4030_LED
  89
  90 /* Board NAND Info */
  91 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
  92 #define MTDIDS_DEFAULT                  "nand0=omap2-nand.0"
  93 #define MTDPARTS_DEFAULT                "mtdparts=omap2-nand.0:" \
  94                                                 "128k(SPL)," \
  95                                                 "1m(u-boot)," \
  96                                                 "384k(u-boot-env1)," \
  97                                                 "1152k(mtdoops)," \
  98                                                 "384k(u-boot-env2)," \
  99                                                 "5m(kernel)," \
 100                                                 "2m(fdt)," \
 101                                                 "-(ubi)"
 102
 103 #define CONFIG_NAND_OMAP_GPMC
 104 #define CONFIG_SYS_NAND_ADDR            NAND_BASE       /* physical address */
 105                                                         /* to access nand */
 106 #define CONFIG_SYS_NAND_BASE            NAND_BASE       /* physical address */
 107                                                         /* to access nand at */
 108                                                         /* CS0 */
 109 #define CONFIG_SYS_MAX_NAND_DEVICE      1               /* Max number of NAND */
 110                                                         /* devices */
 111 #define CONFIG_BCH
 112 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 113 #define CONFIG_SYS_NAND_MAX_ECCPOS      56
 114
 115 /* commands to include */
 116 #define CONFIG_CMD_MTDPARTS             /* Enable MTD parts commands */
 117 #define CONFIG_CMD_NAND                 /* NAND support */
 118 #define CONFIG_CMD_NAND_LOCK_UNLOCK     /* nand (un)lock commands */
 119 #define CONFIG_CMD_UBIFS                /* UBIFS commands */
 120 #define CONFIG_LZO                      /* LZO is needed for UBIFS */
 121
 122 #undef CONFIG_CMD_JFFS2                 /* JFFS2 Support */
 123
 124 /* needed for ubi */
 125 #define CONFIG_RBTREE
 126 #define CONFIG_MTD_DEVICE       /* needed for mtdparts commands */
 127 #define CONFIG_MTD_PARTITIONS
 128
 129 /* Environment information (this is the common part) */
 130
 131
 132 /* hang() the board on panic() */
 133 #define CONFIG_PANIC_HANG
 134
 135 /* environment placement (for NAND), is different for FLASHCARD but does not
 136  * harm there */
 137 #define CONFIG_ENV_OFFSET               0x120000    /* env start */
 138 #define CONFIG_ENV_OFFSET_REDUND        0x2A0000    /* redundant env start */
 139 #define CONFIG_ENV_SIZE                 (16 << 10)  /* use 16KiB for env */
 140 #define CONFIG_ENV_RANGE                (384 << 10) /* allow badblocks in env */
 141
 142 /* the loadaddr is the same as CONFIG_SYS_LOAD_ADDR, unfortunately the defiend
 143  * value can not be used here! */
 144 #define CONFIG_LOADADDR         0x82000000
 145
 146 #define CONFIG_COMMON_ENV_SETTINGS \
 147         "console=ttyO2,115200n8\0" \
 148         "mmcdev=0\0" \
 149         "vram=3M\0" \
 150         "defaultdisplay=lcd\0" \
 151         "kernelopts=mtdoops.mtddev=3\0" \
 152         "mtdparts=" MTDPARTS_DEFAULT "\0" \
 153         "mtdids=" MTDIDS_DEFAULT "\0" \
 154         "commonargs=" \
 155                 "setenv bootargs console=${console} " \
 156                 "${mtdparts} " \
 157                 "${kernelopts} " \
 158                 "vt.global_cursor_default=0 " \
 159                 "vram=${vram} " \
 160                 "omapdss.def_disp=${defaultdisplay}\0"
 161
 162 #define CONFIG_BOOTCOMMAND "run autoboot"
 163
 164 /* specific environment settings for different use cases
 165  * FLASHCARD: used to run a rdimage from sdcard to program the device
 166  * 'NORMAL': used to boot kernel from sdcard, nand, ...
 167  *
 168  * The main aim for the FLASHCARD skin is to have an embedded environment
 169  * which will not be influenced by any data already on the device.
 170  */
 171 #ifdef CONFIG_FLASHCARD
 172
 173 #define CONFIG_ENV_IS_NOWHERE
 174
 175 /* the rdaddr is 16 MiB before the loadaddr */
 176 #define CONFIG_ENV_RDADDR       "rdaddr=0x81000000\0"
 177
 178 #define CONFIG_EXTRA_ENV_SETTINGS \
 179         CONFIG_COMMON_ENV_SETTINGS \
 180         CONFIG_ENV_RDADDR \
 181         "autoboot=" \
 182         "run commonargs; " \
 183         "setenv bootargs ${bootargs} " \
 184                 "flashy_updateimg=/dev/mmcblk0p1:corscience_update.img " \
 185                 "rdinit=/sbin/init; " \
 186         "mmc dev ${mmcdev}; mmc rescan; " \
 187         "fatload mmc ${mmcdev} ${loadaddr} uImage; " \
 188         "fatload mmc ${mmcdev} ${rdaddr} uRamdisk; " \
 189         "bootm ${loadaddr} ${rdaddr}\0"
 190
 191 #else /* CONFIG_FLASHCARD */
 192
 193 #define CONFIG_ENV_OVERWRITE /* allow to overwrite serial and ethaddr */
 194
 195 #define CONFIG_ENV_IS_IN_NAND
 196
 197 #define CONFIG_EXTRA_ENV_SETTINGS \
 198         CONFIG_COMMON_ENV_SETTINGS \
 199         "mmcargs=" \
 200                 "run commonargs; " \
 201                 "setenv bootargs ${bootargs} " \
 202                 "root=/dev/mmcblk0p2 " \
 203                 "rootwait " \
 204                 "rw\0" \
 205         "nandargs=" \
 206                 "run commonargs; " \
 207                 "setenv bootargs ${bootargs} " \
 208                 "root=ubi0:root " \
 209                 "ubi.mtd=7 " \
 210                 "rootfstype=ubifs " \
 211                 "ro\0" \
 212         "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
 213         "bootscript=echo Running bootscript from mmc ...; " \
 214                 "source ${loadaddr}\0" \
 215         "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
 216         "mmcboot=echo Booting from mmc ...; " \
 217                 "run mmcargs; " \
 218                 "bootm ${loadaddr}\0" \
 219         "loaduimage_ubi=ubi part ubi; " \
 220                 "ubifsmount ubi:root; " \
 221                 "ubifsload ${loadaddr} /boot/uImage\0" \
 222         "loaduimage_nand=nand read ${loadaddr} kernel 0x500000\0" \
 223         "nandboot=echo Booting from nand ...; " \
 224                 "run nandargs; " \
 225                 "run loaduimage_nand; " \
 226                 "bootm ${loadaddr}\0" \
 227         "autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \
 228                         "if run loadbootscript; then " \
 229                                 "run bootscript; " \
 230                         "else " \
 231                                 "if run loaduimage; then " \
 232                                         "run mmcboot; " \
 233                                 "else run nandboot; " \
 234                                 "fi; " \
 235                         "fi; " \
 236                 "else run nandboot; fi\0"
 237
 238 #endif /* CONFIG_FLASHCARD */
 239
 240 /* Miscellaneous configurable options */
 241 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 242 #define CONFIG_CMDLINE_EDITING          /* enable cmdline history */
 243 #define CONFIG_AUTO_COMPLETE
 244 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 245 /* Print Buffer Size */
 246 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 247                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 248 #define CONFIG_SYS_MAXARGS              16      /* max number of command args */
 249
 250 /* Boot Argument Buffer Size */
 251 #define CONFIG_SYS_BARGSIZE             (CONFIG_SYS_CBSIZE)
 252
 253 #define CONFIG_SYS_MEMTEST_START        (OMAP34XX_SDRC_CS0 + 0x00000000)
 254 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_MEMTEST_START + \
 255                                         0x07000000) /* 112 MB */
 256
 257 #define CONFIG_SYS_LOAD_ADDR            (OMAP34XX_SDRC_CS0 + 0x02000000)
 258
 259 /*
 260  * OMAP3 has 12 GP timers, they can be driven by the system clock
 261  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
 262  * This rate is divided by a local divisor.
 263  */
 264 #define CONFIG_SYS_TIMERBASE            (OMAP34XX_GPT2)
 265 #define CONFIG_SYS_PTV                  2 /* Divisor: 2^(PTV+1) => 8 */
 266
 267 /*  Physical Memory Map  */
 268 #define CONFIG_NR_DRAM_BANKS            2 /* CS1 may or may not be populated */
 269 #define PHYS_SDRAM_1                    OMAP34XX_SDRC_CS0
 270 #define PHYS_SDRAM_2                    OMAP34XX_SDRC_CS1
 271
 272 /* NAND and environment organization  */
 273 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 2 sectors */
 274
 275 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
 276 #define CONFIG_SYS_INIT_RAM_ADDR        0x4020f800
 277 #define CONFIG_SYS_INIT_RAM_SIZE        0x800
 278 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
 279                                                 CONFIG_SYS_INIT_RAM_SIZE - \
 280                                                 GENERATED_GBL_DATA_SIZE)
 281
 282 /* SRAM config */
 283 #define CONFIG_SYS_SRAM_START           0x40200000
 284 #define CONFIG_SYS_SRAM_SIZE            0x10000
 285
 286 /* Defines for SPL */
 287 #define CONFIG_SPL_FRAMEWORK
 288 #define CONFIG_SPL_NAND_SIMPLE
 289
 290 #define CONFIG_SPL_BOARD_INIT
 291 #define CONFIG_SPL_NAND_BASE
 292 #define CONFIG_SPL_NAND_DRIVERS
 293 #define CONFIG_SPL_NAND_ECC
 294 #define CONFIG_SPL_LDSCRIPT             "arch/arm/mach-omap2/u-boot-spl.lds"
 295 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME        "u-boot.img"
 296 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
 297
 298 #define CONFIG_SPL_TEXT_BASE            0x40200000 /*CONFIG_SYS_SRAM_START*/
 299 #define CONFIG_SPL_MAX_SIZE             (SRAM_SCRATCH_SPACE_ADDR - \
 300                                          CONFIG_SPL_TEXT_BASE)
 301
 302 #define CONFIG_SPL_BSS_START_ADDR       0x80000000 /*CONFIG_SYS_SDRAM_BASE*/
 303 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 304
 305 /* NAND boot config */
 306 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 307 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 308 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
 309 #define CONFIG_SYS_NAND_OOBSIZE         64
 310 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128*1024)
 311 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   NAND_LARGE_BADBLOCK_POS
 312 #define CONFIG_SYS_NAND_ECCPOS          {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \
 313                                          13, 14, 16, 17, 18, 19, 20, 21, 22, \
 314                                          23, 24, 25, 26, 27, 28, 30, 31, 32, \
 315                                          33, 34, 35, 36, 37, 38, 39, 40, 41, \
 316                                          42, 44, 45, 46, 47, 48, 49, 50, 51, \
 317                                          52, 53, 54, 55, 56}
 318
 319 #define CONFIG_SYS_NAND_ECCSIZE         512
 320 #define CONFIG_SYS_NAND_ECCBYTES        13
 321 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
 322
 323 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 324
 325 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x20000
 326 #define CONFIG_SYS_NAND_U_BOOT_SIZE     0x100000
 327
 328 #define CONFIG_SYS_SPL_MALLOC_START     0x80208000
 329 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000        /* 1 MB */
 330
 331 #define CONFIG_SYS_ALT_MEMTEST
 332 #define CONFIG_SYS_MEMTEST_SCRATCH      0x81000000
 333 #endif /* __CONFIG_H */