include/configs/tqma6.h

   1 /*
   2  * Copyright (C) 2013, 2014 Markus Niebel <Markus.Niebel@tq-group.com>
   3  *
   4  * Configuration settings for the TQ Systems TQMa6<Q,S> module.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 /* SPL */
  13 /* #if defined(CONFIG_SPL_BUILD) */
  14
  15 #define CONFIG_SPL_MMC_SUPPORT
  16 #define CONFIG_SPL_SPI_SUPPORT
  17 #define CONFIG_SPL_FAT_SUPPORT
  18 #define CONFIG_SPL_EXT_SUPPORT
  19
  20 /* common IMX6 SPL configuration */
  21 #include "imx6_spl.h"
  22
  23 /* #endif */
  24
  25 #include "mx6_common.h"
  26
  27 #if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
  28 #define PHYS_SDRAM_SIZE                 (512u * SZ_1M)
  29 #elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
  30 #define PHYS_SDRAM_SIZE                 (1024u * SZ_1M)
  31 #endif
  32
  33 #define CONFIG_CMDLINE_TAG
  34 #define CONFIG_SETUP_MEMORY_TAGS
  35 #define CONFIG_INITRD_TAG
  36 #define CONFIG_REVISION_TAG
  37
  38 #define CONFIG_BOARD_EARLY_INIT_F
  39 #define CONFIG_BOARD_LATE_INIT
  40
  41 #define CONFIG_MXC_GPIO
  42 #define CONFIG_MXC_UART
  43
  44 /* SPI */
  45 #define CONFIG_CMD_SPI
  46 #define CONFIG_MXC_SPI
  47
  48 /* SPI Flash */
  49 #define CONFIG_SPI_FLASH
  50 #define CONFIG_SPI_FLASH_STMICRO
  51
  52 #define TQMA6_SPI_FLASH_SECTOR_SIZE     SZ_64K
  53
  54 #define CONFIG_CMD_SF
  55 #define CONFIG_SF_DEFAULT_BUS   0
  56 #define CONFIG_SF_DEFAULT_CS    0
  57 #define CONFIG_SF_DEFAULT_SPEED 50000000
  58 #define CONFIG_SF_DEFAULT_MODE  (SPI_MODE_0)
  59
  60 /* I2C Configs */
  61 #define CONFIG_CMD_I2C
  62 #define CONFIG_SYS_I2C
  63 #define CONFIG_SYS_I2C_MXC
  64 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  65 #define CONFIG_I2C_MULTI_BUS
  66 #define CONFIG_SYS_I2C_SPEED            100000
  67
  68 /* I2C SYSMON (LM75) */
  69 #define CONFIG_DTT_LM75
  70 #define CONFIG_DTT_MAX_TEMP             70
  71 #define CONFIG_DTT_MIN_TEMP             -30
  72 #define CONFIG_DTT_HYSTERESIS   3
  73 #define CONFIG_CMD_DTT
  74
  75 /* I2C EEPROM (M24C64) */
  76 #define CONFIG_SYS_I2C_EEPROM_ADDR                      0x50
  77 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN                  2
  78 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS           5 /* 32 Bytes */
  79 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS       20
  80 #define CONFIG_CMD_EEPROM
  81
  82 #define CONFIG_POWER
  83 #define CONFIG_POWER_I2C
  84 #define CONFIG_POWER_PFUZE100
  85 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
  86 #define TQMA6_PFUZE100_I2C_BUS          2
  87
  88 /* MMC Configs */
  89 #define CONFIG_FSL_ESDHC
  90 #define CONFIG_FSL_USDHC
  91 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  92
  93 #define CONFIG_MMC
  94 #define CONFIG_CMD_MMC
  95 #define CONFIG_GENERIC_MMC
  96 #define CONFIG_BOUNCE_BUFFER
  97
  98 /* USB Configs */
  99 #define CONFIG_CMD_USB
 100 #define CONFIG_USB_EHCI
 101 #define CONFIG_USB_EHCI_MX6
 102 #define CONFIG_USB_STORAGE
 103 #define CONFIG_USB_HOST_ETHER
 104 #define CONFIG_USB_ETHER_SMSC95XX
 105 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
 106 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 107 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
 108
 109 /* Fuses */
 110 #define CONFIG_MXC_OCOTP
 111 #define CONFIG_CMD_FUSE
 112
 113 #define CONFIG_CMD_EXT2
 114 #define CONFIG_CMD_EXT4
 115 #define CONFIG_CMD_EXT4_WRITE
 116 #define CONFIG_CMD_FAT
 117 #define CONFIG_CMD_FS_GENERIC
 118 #define CONFIG_DOS_PARTITION
 119
 120 #define CONFIG_CMD_PING
 121 #define CONFIG_CMD_DHCP
 122 #define CONFIG_CMD_MII
 123 #define CONFIG_CMD_NET
 124
 125 #define CONFIG_FEC_MXC
 126 #define IMX_FEC_BASE                    ENET_BASE_ADDR
 127 #define CONFIG_PHYLIB
 128 #define CONFIG_MII
 129
 130 #define CONFIG_ARP_TIMEOUT              200UL
 131 /* Network config - Allow larger/faster download for TFTP/NFS */
 132 #define CONFIG_IP_DEFRAG
 133 #define CONFIG_TFTP_BLOCKSIZE   4096
 134 #define CONFIG_NFS_READ_SIZE    4096
 135
 136 /* allow to overwrite serial and ethaddr */
 137 #define CONFIG_ENV_OVERWRITE
 138 #define CONFIG_CONS_INDEX               1
 139 #define CONFIG_BAUDRATE                 115200
 140
 141 /* Command definition */
 142 #define CONFIG_CMD_BMODE
 143 #define CONFIG_CMD_BOOTZ
 144 #define CONFIG_CMD_ITEST
 145 #define CONFIG_CMD_SETEXPR
 146
 147 #define CONFIG_BOOTDELAY                3
 148
 149 #define CONFIG_LOADADDR                 0x12000000
 150
 151 /* place code in last 4 MiB of RAM */
 152 #if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
 153 #define CONFIG_SYS_TEXT_BASE            0x2fc00000
 154 #elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
 155 #define CONFIG_SYS_TEXT_BASE            0x4fc00000
 156 #endif
 157
 158 #define CONFIG_ENV_SIZE                 (SZ_8K)
 159 /* Size of malloc() pool */
 160 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 2 * SZ_1M)
 161
 162 #if defined(CONFIG_TQMA6X_MMC_BOOT)
 163
 164 #define CONFIG_ENV_IS_IN_MMC
 165 #define TQMA6_UBOOT_OFFSET              SZ_1K
 166 #define TQMA6_UBOOT_SECTOR_START        0x2
 167 #define TQMA6_UBOOT_SECTOR_COUNT        0x7fe
 168
 169 #define CONFIG_ENV_OFFSET               SZ_1M
 170 #define CONFIG_SYS_MMC_ENV_DEV          0
 171
 172 #define TQMA6_FDT_OFFSET                (2 * SZ_1M)
 173 #define TQMA6_FDT_SECTOR_START          0x1000
 174 #define TQMA6_FDT_SECTOR_COUNT          0x800
 175
 176 #define TQMA6_KERNEL_SECTOR_START       0x2000
 177 #define TQMA6_KERNEL_SECTOR_COUNT       0x2000
 178
 179 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
 180         "uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0"                \
 181         "uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"                 \
 182         "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
 183         "fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                     \
 184         "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
 185         "kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"               \
 186         "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0"                       \
 187         "loadimage=mmc dev ${mmcdev}; "                                        \
 188                 "mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0"       \
 189         "loadfdt=mmc dev ${mmcdev}; "                                          \
 190                 "mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0"             \
 191         "update_uboot=if tftp ${uboot}; then "                                 \
 192                 "if itest ${filesize} > 0; then "                              \
 193                         "mmc dev ${mmcdev}; mmc rescan; "                      \
 194                         "setexpr blkc ${filesize} / 0x200; "                   \
 195                         "setexpr blkc ${blkc} + 1; "                           \
 196                         "if itest ${blkc} <= ${uboot_size}; then "             \
 197                                 "mmc write ${loadaddr} ${uboot_start} "        \
 198                                         "${blkc}; "                            \
 199                         "fi; "                                                 \
 200                 "fi; fi; "                                                     \
 201                 "setenv filesize; setenv blkc \0"                              \
 202         "update_kernel=run kernel_name; "                                      \
 203                 "if tftp ${kernel}; then "                                     \
 204                         "if itest ${filesize} > 0; then "                      \
 205                                 "mmc dev ${mmcdev}; mmc rescan; "              \
 206                                 "setexpr blkc ${filesize} / 0x200; "           \
 207                                 "setexpr blkc ${blkc} + 1; "                   \
 208                                 "if itest ${blkc} <= ${kernel_size}; then "    \
 209                                         "mmc write ${loadaddr} "               \
 210                                                 "${kernel_start} ${blkc}; "    \
 211                                 "fi; "                                         \
 212                         "fi; "                                                 \
 213                 "fi; "                                                         \
 214                 "setenv filesize; setenv blkc \0"                              \
 215         "update_fdt=if tftp ${fdt_file}; then "                                \
 216                 "if itest ${filesize} > 0; then "                              \
 217                         "mmc dev ${mmcdev}; mmc rescan; "                      \
 218                         "setexpr blkc ${filesize} / 0x200; "                   \
 219                         "setexpr blkc ${blkc} + 1; "                           \
 220                         "if itest ${blkc} <= ${fdt_size}; then "               \
 221                                 "mmc write ${loadaddr} ${fdt_start} ${blkc}; " \
 222                         "fi; "                                                 \
 223                 "fi; fi; "                                                     \
 224                 "setenv filesize; setenv blkc \0"                              \
 225
 226 #define CONFIG_BOOTCOMMAND \
 227         "run mmcboot; run netboot; run panicboot"
 228
 229 #elif defined(CONFIG_TQMA6X_SPI_BOOT)
 230
 231 #define TQMA6_UBOOT_OFFSET              0x400
 232 #define TQMA6_UBOOT_SECTOR_START        0x0
 233 /* max u-boot size: 512k */
 234 #define TQMA6_UBOOT_SECTOR_SIZE         TQMA6_SPI_FLASH_SECTOR_SIZE
 235 #define TQMA6_UBOOT_SECTOR_COUNT        0x8
 236 #define TQMA6_UBOOT_SIZE                (TQMA6_UBOOT_SECTOR_SIZE * \
 237                                          TQMA6_UBOOT_SECTOR_COUNT)
 238
 239 #define CONFIG_ENV_IS_IN_SPI_FLASH
 240 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 241 #define CONFIG_ENV_OFFSET               (TQMA6_UBOOT_SIZE)
 242 #define CONFIG_ENV_SECT_SIZE            TQMA6_SPI_FLASH_SECTOR_SIZE
 243 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + \
 244                                          CONFIG_ENV_SECT_SIZE)
 245
 246 #define CONFIG_ENV_SPI_BUS              (CONFIG_SF_DEFAULT_BUS)
 247 #define CONFIG_ENV_SPI_CS               (CONFIG_SF_DEFAULT_CS)
 248 #define CONFIG_ENV_SPI_MAX_HZ           (CONFIG_SF_DEFAULT_SPEED)
 249 #define CONFIG_ENV_SPI_MODE             (CONFIG_SF_DEFAULT_MODE)
 250
 251 #define TQMA6_FDT_OFFSET                (CONFIG_ENV_OFFSET_REDUND + \
 252                                          CONFIG_ENV_SECT_SIZE)
 253 #define TQMA6_FDT_SECT_SIZE             (TQMA6_SPI_FLASH_SECTOR_SIZE)
 254
 255 #define TQMA6_FDT_SECTOR_START          0x0a /* 8 Sector u-boot, 2 Sector env */
 256 #define TQMA6_FDT_SECTOR_COUNT          0x01
 257
 258 #define TQMA6_KERNEL_SECTOR_START       0x10
 259 #define TQMA6_KERNEL_SECTOR_COUNT       0x60
 260
 261 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
 262         "mmcblkdev=0\0"                                                        \
 263         "uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0"                     \
 264         "uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"              \
 265         "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
 266         "fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                  \
 267         "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
 268         "kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"            \
 269         "update_uboot=if tftp ${uboot}; then "                                 \
 270                 "if itest ${filesize} > 0; then "                              \
 271                         "setexpr blkc ${filesize} + "                          \
 272                                 __stringify(TQMA6_UBOOT_OFFSET) "; "           \
 273                         "setexpr size ${uboot_sectors} * "                     \
 274                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 275                         "if itest ${blkc} <= ${size}; then "                   \
 276                                 "sf probe; "                                   \
 277                                 "sf erase 0 ${size}; "                         \
 278                                 "sf write ${loadaddr} ${uboot_offset} "        \
 279                                         "${filesize}; "                        \
 280                         "fi; "                                                 \
 281                 "fi; fi; "                                                     \
 282                 "setenv filesize 0; setenv blkc; setenv size \0"               \
 283         "update_kernel=run kernel_name; if tftp ${kernel}; then "              \
 284                 "if itest ${filesize} > 0; then "                              \
 285                         "setexpr size ${kernel_sectors} * "                    \
 286                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 287                         "setexpr offset ${kernel_start} * "                    \
 288                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 289                         "if itest ${filesize} <= ${size}; then "               \
 290                                 "sf probe; "                                   \
 291                                 "sf erase ${offset} ${size}; "                 \
 292                                 "sf write ${loadaddr} ${offset} "              \
 293                                         "${filesize}; "                        \
 294                         "fi; "                                                 \
 295                 "fi; fi; "                                                     \
 296                 "setenv filesize 0; setenv size ; setenv offset\0"             \
 297         "update_fdt=if tftp ${fdt_file}; then "                                \
 298                 "if itest ${filesize} > 0; then "                              \
 299                         "setexpr size ${fdt_sectors} * "                       \
 300                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 301                         "setexpr offset ${fdt_start} * "                       \
 302                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 303                         "if itest ${filesize} <= ${size}; then "               \
 304                                 "sf probe; "                                   \
 305                                 "sf erase ${offset} ${size}; "                 \
 306                                 "sf write ${loadaddr} ${offset} "              \
 307                                         "${filesize}; "                        \
 308                         "fi; "                                                 \
 309                 "fi; fi; "                                                     \
 310                 "setenv filesize 0; setenv size ; setenv offset\0"             \
 311         "loadimage=sf probe; "                                                 \
 312                 "setexpr size ${kernel_sectors} * "                            \
 313                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 314                 "setexpr offset ${kernel_start} * "                            \
 315                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 316                 "sf read ${loadaddr} ${offset} ${size}; "                      \
 317                 "setenv size ; setenv offset\0"                                \
 318         "loadfdt=sf probe; "                                                   \
 319                 "setexpr size ${fdt_sectors} * "                               \
 320                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 321                 "setexpr offset ${fdt_start} * "                               \
 322                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 323                 "sf read ${${fdt_addr}} ${offset} ${size}; "                   \
 324                 "setenv size ; setenv offset\0"                                \
 325
 326
 327 #define CONFIG_BOOTCOMMAND                                                     \
 328         "sf probe; run mmcboot; run netboot; run panicboot"                    \
 329
 330 #else
 331
 332 #error "need to define boot source"
 333
 334 #endif
 335
 336 /* 128 MiB offset as in ARM related docu for linux suggested */
 337 #define TQMA6_FDT_ADDRESS               0x18000000
 338
 339 #define CONFIG_EXTRA_ENV_SETTINGS                                              \
 340         "board=tqma6\0"                                                        \
 341         "uimage=uImage\0"                                                      \
 342         "zimage=zImage\0"                                                      \
 343         "boot_type=bootz\0"                                                    \
 344         "kernel_name=if test \"${boot_type}\" != bootz; then "                 \
 345                 "setenv kernel ${uimage}; "                                    \
 346                 "else setenv kernel ${zimage}; fi\0"                           \
 347         "uboot=u-boot.imx\0"                                                   \
 348         "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0"                               \
 349         "fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0"                          \
 350         "console=" CONFIG_CONSOLE_DEV "\0"                                     \
 351         "fdt_high=0xffffffff\0"                                                \
 352         "initrd_high=0xffffffff\0"                                             \
 353         "addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0"  \
 354         "addfb=setenv bootargs ${bootargs} "                                   \
 355                 "imx-fbdev.legacyfb_depth=32 consoleblank=0\0"                 \
 356         "mmcpart=2\0"                                                          \
 357         "mmcblkdev=0\0"                                                        \
 358         "mmcargs=run addmmc addtty addfb\0"                                    \
 359         "addmmc=setenv bootargs ${bootargs} "                                  \
 360                 "root=/dev/mmcblk${mmcblkdev}p${mmcpart} rw rootwait\0"        \
 361         "mmcboot=echo Booting from mmc ...; "                                  \
 362                 "setenv bootargs; "                                            \
 363                 "run mmcargs; "                                                \
 364                 "run loadimage; "                                              \
 365                 "if run loadfdt; then "                                        \
 366                         "echo boot device tree kernel ...; "                   \
 367                         "${boot_type} ${loadaddr} - ${fdt_addr}; "             \
 368                 "else "                                                        \
 369                         "${boot_type}; "                                       \
 370                 "fi;\0"                                                        \
 371                 "setenv bootargs \0"                                           \
 372         "netdev=eth0\0"                                                        \
 373         "rootpath=/srv/nfs/tqma6\0"                                            \
 374         "ipmode=static\0"                                                      \
 375         "netargs=run addnfs addip addtty addfb\0"                              \
 376         "addnfs=setenv bootargs ${bootargs} "                                  \
 377                 "root=/dev/nfs rw "                                            \
 378                 "nfsroot=${serverip}:${rootpath},v3,tcp;\0"                    \
 379         "addip_static=setenv bootargs ${bootargs} "                            \
 380                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:"            \
 381                 "${hostname}:${netdev}:off\0"                                  \
 382         "addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0"                  \
 383         "addip=if test \"${ipmode}\" != static; then "                         \
 384                 "run addip_dynamic; else run addip_static; fi\0"               \
 385         "set_getcmd=if test \"${ipmode}\" != static; then "                    \
 386                 "setenv getcmd dhcp; setenv autoload yes; "                    \
 387                 "else setenv getcmd tftp; setenv autoload no; fi\0"            \
 388         "netboot=echo Booting from net ...; "                                  \
 389                 "run kernel_name; "                                            \
 390                 "run set_getcmd; "                                             \
 391                 "setenv bootargs; "                                            \
 392                 "run netargs; "                                                \
 393                 "if ${getcmd} ${kernel}; then "                                \
 394                         "if ${getcmd} ${fdt_addr} ${fdt_file}; then "          \
 395                                 "${boot_type} ${loadaddr} - ${fdt_addr}; "     \
 396                         "fi; "                                                 \
 397                 "fi; "                                                         \
 398                 "echo ... failed\0"                                            \
 399         "panicboot=echo No boot device !!! reset\0"                            \
 400         TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                      \
 401
 402 /* Miscellaneous configurable options */
 403 #define CONFIG_SYS_LONGHELP
 404 #define CONFIG_SYS_HUSH_PARSER
 405 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
 406
 407 #define CONFIG_AUTO_COMPLETE
 408 #define CONFIG_SYS_CBSIZE               512
 409
 410 /* Print Buffer Size */
 411 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 412                                          sizeof(CONFIG_SYS_PROMPT) + 16)
 413 #define CONFIG_SYS_MAXARGS              16
 414 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 415
 416 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 417
 418 #define CONFIG_CMDLINE_EDITING
 419 #define CONFIG_STACKSIZE                (128u * SZ_1K)
 420
 421 /* Physical Memory Map */
 422 #define CONFIG_NR_DRAM_BANKS            1
 423 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 424
 425 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 426 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 427 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 428
 429 #define CONFIG_SYS_INIT_SP_OFFSET \
 430         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 431 #define CONFIG_SYS_INIT_SP_ADDR \
 432         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 433
 434 #define CONFIG_OF_LIBFDT
 435 #define CONFIG_OF_BOARD_SETUP
 436 #define CONFIG_FIT
 437 #define CONFIG_FIT_VERBOSE
 438
 439 #ifndef CONFIG_SYS_DCACHE_OFF
 440 #define CONFIG_CMD_CACHE
 441 #endif
 442
 443 /*
 444  * All the defines above are for the TQMa6 SoM
 445  *
 446  * Now include the baseboard specific configuration
 447  */
 448 #ifdef CONFIG_MBA6
 449 #include "tqma6_mba6.h"
 450 #else
 451 #error "No baseboard for the TQMa6 defined!"
 452 #endif
 453
 454 /* Support at least the sensor on TQMa6 SOM */
 455 #if !defined(CONFIG_DTT_SENSORS)
 456 #define CONFIG_DTT_SENSORS              { 0 }
 457 #endif
 458
 459 #endif /* __CONFIG_H */