Merge branch '2021-12-01-Kconfig-migrations' into next
[platform/kernel/u-boot.git] / include / configs / topic_miami.h
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * (C) Copyright 2014 Topic Embedded Products
4  *
5  * Configuration for Zynq Evaluation and Development Board - Miami
6  * See zynq-common.h for Zynq common configs
7  */
8
9 #ifndef __CONFIG_TOPIC_MIAMI_H
10 #define __CONFIG_TOPIC_MIAMI_H
11
12
13 /* Speed up boot time by ignoring the environment which we never used */
14
15 #include "zynq-common.h"
16
17 /* Fixup settings */
18
19 /* SPL settings */
20 #undef CONFIG_SPL_ETH
21 #undef CONFIG_SPL_MAX_FOOTPRINT
22 #define CONFIG_SPL_MAX_FOOTPRINT        CONFIG_SYS_SPI_U_BOOT_OFFS
23 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot.img"
24
25 /* FPGA commands that we don't use */
26
27 /* Extras */
28
29 /* Faster flash, ours may run at 108 MHz */
30 #undef CONFIG_SPI_FLASH_WINBOND
31
32 /* Setup proper boot sequences for Miami boards */
33
34 #if defined(CONFIG_USB_HOST)
35 # define EXTRA_ENV_USB \
36         "usbreset=i2c dev 1 && i2c mw 41 1 ff && i2c mw 41 3 fe && "\
37                 "i2c mw 41 1 fe && i2c mw 41 1 ff\0" \
38         "usbboot=run usbreset && if usb start; then " \
39                 "echo Booting from USB... && " \
40                 "if load usb 0 0x1900000 ${bootscript}; then "\
41                 "source 0x1900000; fi; " \
42                 "load usb 0 ${kernel_addr} ${kernel_image} && " \
43                 "load usb 0 ${devicetree_addr} ${devicetree_image} && " \
44                 "load usb 0 ${ramdisk_load_address} ${ramdisk_image} && " \
45                 "bootm ${kernel_addr} ${ramdisk_load_address} "\
46                         "${devicetree_addr}; " \
47         "fi\0"
48   /* Note that addresses here should match the addresses in the env */
49 # define DFU_ALT_INFO \
50         "dfu_alt_info=" \
51         "uImage ram 0x2080000 0x500000;" \
52         "devicetree.dtb ram 0x2000000 0x20000;" \
53         "uramdisk.image.gz ram 0x4000000 0x10000000\0" \
54         "dfu_ram=run usbreset && dfu 0 ram 0\0" \
55         "thor_ram=run usbreset && thordown 0 ram 0\0"
56 #else
57 # define EXTRA_ENV_USB
58 #endif
59
60 #undef CONFIG_EXTRA_ENV_SETTINGS
61 #define CONFIG_EXTRA_ENV_SETTINGS       \
62         "kernel_image=uImage\0" \
63         "kernel_addr=0x2080000\0" \
64         "ramdisk_image=uramdisk.image.gz\0"     \
65         "ramdisk_load_address=0x4000000\0"      \
66         "devicetree_image=devicetree.dtb\0"     \
67         "devicetree_addr=0x2000000\0"   \
68         "bitstream_image=fpga.bin\0"    \
69         "bootscript=autorun.scr\0" \
70         "loadbit_addr=0x100000\0"       \
71         "loadbootenv_addr=0x2000000\0" \
72         "kernel_size=0x440000\0"        \
73         "devicetree_size=0x10000\0"     \
74         "boot_size=0xF00000\0"  \
75         "fdt_high=0x20000000\0" \
76         "initrd_high=0x20000000\0"      \
77         "mmc_loadbit=echo Loading bitstream from SD/MMC/eMMC to RAM.. && " \
78                 "mmcinfo && " \
79                 "load mmc 0 ${loadbit_addr} ${bitstream_image} && " \
80                 "fpga load 0 ${loadbit_addr} ${filesize}\0" \
81         "qspiboot=echo Booting from QSPI flash... && " \
82                 "sf probe && " \
83                 "sf read ${devicetree_addr} 0xA0000 ${devicetree_size} && " \
84                 "sf read ${kernel_addr} 0xC0000 ${kernel_size} && " \
85                 "bootm ${kernel_addr} - ${devicetree_addr}\0" \
86         "sdboot=if mmcinfo; then " \
87                         "setenv bootargs console=ttyPS0,115200 " \
88                                 "root=/dev/mmcblk0p2 rw rootfstype=ext4 " \
89                                 "rootwait quiet ; " \
90                         "load mmc 0 ${kernel_addr} ${kernel_image}&& " \
91                         "load mmc 0 ${devicetree_addr} ${devicetree_image}&& " \
92                         "bootm ${kernel_addr} - ${devicetree_addr}; " \
93                 "fi\0" \
94         EXTRA_ENV_USB \
95         DFU_ALT_INFO
96
97 #endif /* __CONFIG_TOPIC_MIAMI_H */