include/configs/topic_miami.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * (C) Copyright 2014 Topic Embedded Products
   4  *
   5  * Configuration for Zynq Evaluation and Development Board - Miami
   6  * See zynq-common.h for Zynq common configs
   7  */
   8
   9 #ifndef __CONFIG_TOPIC_MIAMI_H
  10 #define __CONFIG_TOPIC_MIAMI_H
  11
  12
  13 /* Speed up boot time by ignoring the environment which we never used */
  14
  15 #include "zynq-common.h"
  16
  17 /* Fixup settings */
  18
  19 /* Setup proper boot sequences for Miami boards */
  20
  21 #if defined(CONFIG_USB_HOST)
  22 # define EXTRA_ENV_USB \
  23         "usbreset=i2c dev 1 && i2c mw 41 1 ff && i2c mw 41 3 fe && "\
  24                 "i2c mw 41 1 fe && i2c mw 41 1 ff\0" \
  25         "usbboot=run usbreset && if usb start; then " \
  26                 "echo Booting from USB... && " \
  27                 "if load usb 0 0x1900000 ${bootscript}; then "\
  28                 "source 0x1900000; fi; " \
  29                 "load usb 0 ${kernel_addr} ${kernel_image} && " \
  30                 "load usb 0 ${devicetree_addr} ${devicetree_image} && " \
  31                 "load usb 0 ${ramdisk_load_address} ${ramdisk_image} && " \
  32                 "bootm ${kernel_addr} ${ramdisk_load_address} "\
  33                         "${devicetree_addr}; " \
  34         "fi\0"
  35   /* Note that addresses here should match the addresses in the env */
  36 # define DFU_ALT_INFO \
  37         "dfu_alt_info=" \
  38         "uImage ram 0x2080000 0x500000;" \
  39         "devicetree.dtb ram 0x2000000 0x20000;" \
  40         "uramdisk.image.gz ram 0x4000000 0x10000000\0" \
  41         "dfu_ram=run usbreset && dfu 0 ram 0\0" \
  42         "thor_ram=run usbreset && thordown 0 ram 0\0"
  43 #else
  44 # define EXTRA_ENV_USB
  45 #endif
  46
  47 #undef CFG_EXTRA_ENV_SETTINGS
  48 #define CFG_EXTRA_ENV_SETTINGS  \
  49         "kernel_image=uImage\0" \
  50         "kernel_addr=0x2080000\0" \
  51         "ramdisk_image=uramdisk.image.gz\0"     \
  52         "ramdisk_load_address=0x4000000\0"      \
  53         "devicetree_image=devicetree.dtb\0"     \
  54         "devicetree_addr=0x2000000\0"   \
  55         "bitstream_image=fpga.bin\0"    \
  56         "bootscript=autorun.scr\0" \
  57         "loadbit_addr=0x100000\0"       \
  58         "loadbootenv_addr=0x2000000\0" \
  59         "kernel_size=0x440000\0"        \
  60         "devicetree_size=0x10000\0"     \
  61         "boot_size=0xF00000\0"  \
  62         "fdt_high=0x20000000\0" \
  63         "initrd_high=0x20000000\0"      \
  64         "mmc_loadbit=echo Loading bitstream from SD/MMC/eMMC to RAM.. && " \
  65                 "mmcinfo && " \
  66                 "load mmc 0 ${loadbit_addr} ${bitstream_image} && " \
  67                 "fpga load 0 ${loadbit_addr} ${filesize}\0" \
  68         "qspiboot=echo Booting from QSPI flash... && " \
  69                 "sf probe && " \
  70                 "sf read ${devicetree_addr} 0xA0000 ${devicetree_size} && " \
  71                 "sf read ${kernel_addr} 0xC0000 ${kernel_size} && " \
  72                 "bootm ${kernel_addr} - ${devicetree_addr}\0" \
  73         "sdboot=if mmcinfo; then " \
  74                         "setenv bootargs console=ttyPS0,115200 " \
  75                                 "root=/dev/mmcblk0p2 rw rootfstype=ext4 " \
  76                                 "rootwait quiet ; " \
  77                         "load mmc 0 ${kernel_addr} ${kernel_image}&& " \
  78                         "load mmc 0 ${devicetree_addr} ${devicetree_image}&& " \
  79                         "bootm ${kernel_addr} - ${devicetree_addr}; " \
  80                 "fi\0" \
  81         EXTRA_ENV_USB \
  82         DFU_ALT_INFO
  83
  84 #endif /* __CONFIG_TOPIC_MIAMI_H */