2 * Configuration settings for the TechNexion TAO-3530 SOM
3 * equipped on Thunder baseboard.
5 * Edward Lin <linuxfae@technexion.com>
6 * Tapani Utriainen <linuxfae@technexion.com>
8 * Copyright (C) 2013 Stefan Roese <sr@denx.de>
10 * SPDX-License-Identifier: GPL-2.0+
17 * High Level Configuration Options
19 #define CONFIG_OMAP /* in a TI OMAP core */
21 #define CONFIG_OMAP_GPIO
22 #define CONFIG_OMAP_COMMON
23 /* Common ARM Erratas */
24 #define CONFIG_ARM_ERRATA_454179
25 #define CONFIG_ARM_ERRATA_430973
26 #define CONFIG_ARM_ERRATA_621766
28 #define MACH_TYPE_OMAP3_TAO3530 2836
30 #define CONFIG_SDRC /* Has an SDRC controller */
32 #include <asm/arch/cpu.h> /* get chip and board defs */
33 #include <asm/arch/omap.h>
36 * Display CPU and Board information
38 #define CONFIG_DISPLAY_CPUINFO
39 #define CONFIG_DISPLAY_BOARDINFO
42 #define V_OSCK 26000000 /* Clock output from T2 */
43 #define V_SCLK (V_OSCK >> 1)
45 #define CONFIG_MISC_INIT_R
47 #define CONFIG_OF_LIBFDT
49 #define CONFIG_CMDLINE_TAG
50 #define CONFIG_SETUP_MEMORY_TAGS
51 #define CONFIG_INITRD_TAG
52 #define CONFIG_REVISION_TAG
55 * Size of malloc() pool
57 #define CONFIG_SYS_MALLOC_LEN (4 << 20)
58 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */
65 * NS16550 Configuration
67 #define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
69 #define CONFIG_SYS_NS16550_SERIAL
70 #define CONFIG_SYS_NS16550_REG_SIZE (-4)
71 #define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
74 * select serial console configuration
76 #define CONFIG_CONS_INDEX 3
77 #define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
79 /* allow to overwrite serial and ethaddr */
80 #define CONFIG_ENV_OVERWRITE
81 #define CONFIG_BAUDRATE 115200
82 #define CONFIG_GENERIC_MMC
84 #define CONFIG_OMAP_HSMMC
85 #define CONFIG_DOS_PARTITION
88 #define CONFIG_OMAP3_GPIO_2 /* GPIO32 ..63 is in GPIO bank 2 */
89 #define CONFIG_OMAP3_GPIO_3 /* GPIO64 ..95 is in GPIO bank 3 */
90 #define CONFIG_OMAP3_GPIO_4 /* GPIO96 ..127 is in GPIO bank 4 */
91 #define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */
92 #define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
94 /* commands to include */
95 #define CONFIG_CMD_CACHE
96 #define CONFIG_CMD_EXT2 /* EXT2 Support */
97 #define CONFIG_CMD_FAT /* FAT support */
98 #define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
99 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
100 #define MTDIDS_DEFAULT "nand0=nand"
101 #define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
102 "1920k(u-boot),128k(u-boot-env),"\
105 #define CONFIG_CMD_I2C /* I2C serial bus support */
106 #define CONFIG_CMD_MMC /* MMC support */
107 #define CONFIG_CMD_NAND /* NAND support */
108 #define CONFIG_CMD_DHCP
109 #define CONFIG_CMD_PING
111 #define CONFIG_SYS_NO_FLASH
112 #define CONFIG_SYS_I2C
113 #define CONFIG_SYS_I2C_OMAP34XX
114 #define CONFIG_SYS_OMAP24_I2C_SPEED 100000
115 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1
116 #define CONFIG_I2C_MULTI_BUS
121 #define CONFIG_TWL4030_POWER
122 #define CONFIG_TWL4030_LED
127 #define CONFIG_NAND_OMAP_GPMC
128 #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
130 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
131 /* to access nand at */
134 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
136 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT
137 /* Environment information */
138 #define CONFIG_BOOTDELAY 3
140 #define CONFIG_EXTRA_ENV_SETTINGS \
141 "loadaddr=0x82000000\0" \
142 "console=ttyO2,115200n8\0" \
144 "dvi_mode=omapfb.mode=dvi:1280x720-24@60\0" \
145 "tv_mode=omapfb.mode=tv:ntsc\0" \
146 "video_mode=omapdss.def_disp=lcd vram=6M omapfb.vram=0:2M,1:2M,2:2M\0" \
147 "lcd_mode=omapfb.mode=lcd:800x480@60 \0" \
148 "extra_options= \0" \
150 "mmcroot=/dev/mmcblk0p2 rw\0" \
151 "mmcrootfstype=ext3 rootwait\0" \
152 "nandroot=ubi0:rootfs ubi.mtd=4\0" \
153 "nandrootfstype=ubifs\0" \
154 "mmcargs=setenv bootargs console=${console} " \
155 "mpurate=${mpurate} " \
158 "rootfstype=${mmcrootfstype} " \
159 "${extra_options}\0" \
160 "nandargs=setenv bootargs console=${console} " \
161 "mpurate=${mpurate} " \
163 "${network_setting} " \
164 "root=${nandroot} " \
165 "rootfstype=${nandrootfstype} "\
166 "${extra_options}\0" \
167 "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
168 "bootscript=echo Running bootscript from mmc ...; " \
169 "source ${loadaddr}\0" \
170 "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
171 "mmcboot=echo Booting from mmc ...; " \
173 "bootm ${loadaddr}\0" \
174 "nandboot=echo Booting from nand ...; " \
176 "nand read ${loadaddr} 280000 400000; " \
177 "bootm ${loadaddr}\0" \
179 #define CONFIG_BOOTCOMMAND \
180 "if mmc rescan ${mmcdev}; then " \
181 "if run loadbootscript; then " \
184 "if run loaduimage; then " \
186 "else run nandboot; " \
189 "else run nandboot; fi"
192 * Miscellaneous configurable options
194 #define CONFIG_SYS_LONGHELP /* undef to save memory */
195 #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
196 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
198 /* turn on command-line edit/hist/auto */
199 #define CONFIG_CMDLINE_EDITING
200 #define CONFIG_COMMAND_HISTORY
201 #define CONFIG_AUTO_COMPLETE
203 /* Print Buffer Size */
204 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
205 sizeof(CONFIG_SYS_PROMPT) + 16)
206 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
207 /* Boot Argument Buffer Size */
208 #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
210 #define CONFIG_SYS_ALT_MEMTEST 1
211 #define CONFIG_SYS_MEMTEST_START (0x82000000) /* memtest */
213 #define CONFIG_SYS_MEMTEST_END (0x83FFFFFF) /* 64MB */
214 #define CONFIG_SYS_MEMTEST_SCRATCH (0x81000000) /* dummy address */
216 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */
218 #define CONFIG_SYS_TEXT_BASE 0x80008000
221 * OMAP3 has 12 GP timers, they can be driven by the system clock
222 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
223 * This rate is divided by a local divisor.
225 #define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
226 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
231 * The stack sizes are set up in start.S using the settings below
233 #define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
236 * Physical Memory Map
238 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
239 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
240 #define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
241 #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
244 * FLASH and environment organization
247 /* **** PISMO SUPPORT *** */
248 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
249 #define CONFIG_SYS_FLASH_BASE NAND_BASE
251 /* Monitor at start of flash */
252 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
253 #define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
255 #define CONFIG_ENV_IS_IN_NAND 1
256 #define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
257 #define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
259 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10)
260 #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
261 #define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET
263 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
264 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
265 #define CONFIG_SYS_INIT_RAM_SIZE 0x800
266 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
267 CONFIG_SYS_INIT_RAM_SIZE - \
268 GENERATED_GBL_DATA_SIZE)
270 #define CONFIG_OMAP3_SPI
275 * Currently only EHCI is enabled, the MUSB OTG controller
280 #define CONFIG_CMD_USB
281 #define CONFIG_USB_EHCI
282 #define CONFIG_USB_EHCI_OMAP
283 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 162
285 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
286 #define CONFIG_USB_HOST_ETHER
287 #define CONFIG_USB_ETHER_SMSC95XX
289 #define CONFIG_USB_ETHER
290 #define CONFIG_USB_ETHER_RNDIS
291 #define CONFIG_USB_STORAGE
292 #define CONGIG_CMD_STORAGE
294 /* Defines for SPL */
295 #define CONFIG_SPL_FRAMEWORK
296 #define CONFIG_SPL_NAND_SIMPLE
298 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
299 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
300 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
301 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
303 #define CONFIG_SPL_BOARD_INIT
304 #define CONFIG_SPL_LIBCOMMON_SUPPORT
305 #define CONFIG_SPL_LIBDISK_SUPPORT
306 #define CONFIG_SPL_I2C_SUPPORT
307 #define CONFIG_SPL_LIBGENERIC_SUPPORT
308 #define CONFIG_SPL_MMC_SUPPORT
309 #define CONFIG_SPL_FAT_SUPPORT
310 #define CONFIG_SPL_SERIAL_SUPPORT
311 #define CONFIG_SPL_NAND_SUPPORT
312 #define CONFIG_SPL_NAND_BASE
313 #define CONFIG_SPL_NAND_DRIVERS
314 #define CONFIG_SPL_NAND_ECC
315 #define CONFIG_SPL_GPIO_SUPPORT
316 #define CONFIG_SPL_POWER_SUPPORT
317 #define CONFIG_SPL_OMAP3_ID_NAND
318 #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
320 /* NAND boot config */
321 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
322 #define CONFIG_SYS_NAND_PAGE_COUNT 64
323 #define CONFIG_SYS_NAND_PAGE_SIZE 2048
324 #define CONFIG_SYS_NAND_OOBSIZE 64
325 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
326 #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
328 * Use the ECC/OOB layout from omap_gpmc.h that matches your chip:
329 * SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT
331 #define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
333 #define CONFIG_SYS_NAND_ECCSIZE 512
334 #define CONFIG_SYS_NAND_ECCBYTES 3
335 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
337 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
338 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
340 #define CONFIG_SPL_TEXT_BASE 0x40200800
341 #define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
344 * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the
345 * older x-loader implementations. And move the BSS area so that it
346 * doesn't overlap with TEXT_BASE.
348 #define CONFIG_SYS_TEXT_BASE 0x80008000
349 #define CONFIG_SPL_BSS_START_ADDR 0x80100000
350 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
352 #define CONFIG_SYS_SPL_MALLOC_START 0x80208000
353 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
355 #endif /* __CONFIG_H */