include/configs/tao3530.h

   1 /*
   2  * Configuration settings for the TechNexion TAO-3530 SOM
   3  * equipped on Thunder baseboard.
   4  *
   5  * Edward Lin <linuxfae@technexion.com>
   6  * Tapani Utriainen <linuxfae@technexion.com>
   7  *
   8  * Copyright (C) 2013 Stefan Roese <sr@denx.de>
   9  *
  10  * SPDX-License-Identifier:     GPL-2.0+
  11  */
  12
  13 #ifndef __CONFIG_H
  14 #define __CONFIG_H
  15
  16 /*
  17  * High Level Configuration Options
  18  */
  19
  20 #include <asm/arch/cpu.h>               /* get chip and board defs */
  21 #include <asm/arch/omap.h>
  22
  23 /* Clock Defines */
  24 #define V_OSCK                  26000000        /* Clock output from T2 */
  25 #define V_SCLK                  (V_OSCK >> 1)
  26
  27 #define CONFIG_MISC_INIT_R
  28
  29 #define CONFIG_CMDLINE_TAG
  30 #define CONFIG_SETUP_MEMORY_TAGS
  31 #define CONFIG_INITRD_TAG
  32 #define CONFIG_REVISION_TAG
  33
  34 /*
  35  * Size of malloc() pool
  36  */
  37 #define CONFIG_SYS_MALLOC_LEN           (4 << 20)
  38 #define CONFIG_ENV_SIZE                 (128 << 10)     /* 128 KiB sector */
  39
  40 /*
  41  * Hardware drivers
  42  */
  43
  44 /*
  45  * NS16550 Configuration
  46  */
  47 #define V_NS16550_CLK                   48000000        /* 48MHz (APLL96/2) */
  48
  49 #define CONFIG_SYS_NS16550_SERIAL
  50 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
  51 #define CONFIG_SYS_NS16550_CLK          V_NS16550_CLK
  52
  53 /*
  54  * select serial console configuration
  55  */
  56 #define CONFIG_SYS_NS16550_COM3         OMAP34XX_UART3
  57
  58 /* allow to overwrite serial and ethaddr */
  59 #define CONFIG_ENV_OVERWRITE
  60
  61 /* commands to include */
  62 #define CONFIG_MTD_DEVICE       /* needed for mtdparts commands */
  63
  64 #define CONFIG_SYS_I2C
  65 #define CONFIG_I2C_MULTI_BUS
  66
  67 /*
  68  * TWL4030
  69  */
  70 #define CONFIG_TWL4030_LED
  71
  72 /*
  73  * Board NAND Info.
  74  */
  75 #define CONFIG_SYS_NAND_ADDR            NAND_BASE       /* physical address */
  76                                                         /* to access nand */
  77 #define CONFIG_SYS_NAND_BASE            NAND_BASE       /* physical address */
  78                                                         /* to access nand at */
  79                                                         /* CS0 */
  80
  81 #define CONFIG_SYS_MAX_NAND_DEVICE      1               /* Max number of NAND */
  82                                                         /* devices */
  83 /* Environment information */
  84
  85 #define CONFIG_EXTRA_ENV_SETTINGS \
  86         "loadaddr=0x82000000\0" \
  87         "console=ttyO2,115200n8\0" \
  88         "mpurate=600\0" \
  89         "dvi_mode=omapfb.mode=dvi:1280x720-24@60\0" \
  90         "tv_mode=omapfb.mode=tv:ntsc\0" \
  91         "video_mode=omapdss.def_disp=lcd vram=6M omapfb.vram=0:2M,1:2M,2:2M\0" \
  92         "lcd_mode=omapfb.mode=lcd:800x480@60 \0" \
  93         "extra_options= \0" \
  94         "mmcdev=0\0" \
  95         "mmcroot=/dev/mmcblk0p2 rw\0" \
  96         "mmcrootfstype=ext3 rootwait\0" \
  97         "nandroot=ubi0:rootfs ubi.mtd=4\0" \
  98         "nandrootfstype=ubifs\0" \
  99         "mmcargs=setenv bootargs console=${console} " \
 100                 "mpurate=${mpurate} " \
 101                 "${video_mode} " \
 102                 "root=${mmcroot} " \
 103                 "rootfstype=${mmcrootfstype} " \
 104                 "${extra_options}\0" \
 105         "nandargs=setenv bootargs console=${console} " \
 106                 "mpurate=${mpurate} " \
 107                 "${video_mode} " \
 108                 "${network_setting} " \
 109                 "root=${nandroot} " \
 110                 "rootfstype=${nandrootfstype} "\
 111                 "${extra_options}\0" \
 112         "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
 113         "bootscript=echo Running bootscript from mmc ...; " \
 114                 "source ${loadaddr}\0" \
 115         "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
 116         "mmcboot=echo Booting from mmc ...; " \
 117                 "run mmcargs; " \
 118                 "bootm ${loadaddr}\0" \
 119         "nandboot=echo Booting from nand ...; " \
 120                 "run nandargs; " \
 121                 "nand read ${loadaddr} 280000 400000; " \
 122                 "bootm ${loadaddr}\0" \
 123
 124 #define CONFIG_BOOTCOMMAND \
 125         "if mmc rescan ${mmcdev}; then " \
 126                 "if run loadbootscript; then " \
 127                         "run bootscript; " \
 128                 "else " \
 129                         "if run loaduimage; then " \
 130                                 "run mmcboot; " \
 131                         "else run nandboot; " \
 132                         "fi; " \
 133                 "fi; " \
 134         "else run nandboot; fi"
 135
 136 /*
 137  * Miscellaneous configurable options
 138  */
 139
 140 /* turn on command-line edit/hist/auto */
 141
 142 #define CONFIG_SYS_ALT_MEMTEST          1
 143 #define CONFIG_SYS_MEMTEST_START        (0x82000000)            /* memtest */
 144                                                                 /* defaults */
 145 #define CONFIG_SYS_MEMTEST_END          (0x83FFFFFF)            /* 64MB */
 146 #define CONFIG_SYS_MEMTEST_SCRATCH      (0x81000000)    /* dummy address */
 147
 148 #define CONFIG_SYS_LOAD_ADDR            (OMAP34XX_SDRC_CS0)     /* default */
 149                                                         /* load address */
 150
 151 /*
 152  * OMAP3 has 12 GP timers, they can be driven by the system clock
 153  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
 154  * This rate is divided by a local divisor.
 155  */
 156 #define CONFIG_SYS_TIMERBASE            (OMAP34XX_GPT2)
 157 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
 158
 159 /*
 160  * Physical Memory Map
 161  */
 162 #define CONFIG_NR_DRAM_BANKS    2       /* CS1 may or may not be populated */
 163 #define PHYS_SDRAM_1            OMAP34XX_SDRC_CS0
 164 #define PHYS_SDRAM_1_SIZE       (32 << 20)      /* at least 32 MiB */
 165 #define PHYS_SDRAM_2            OMAP34XX_SDRC_CS1
 166
 167 /*
 168  * FLASH and environment organization
 169  */
 170
 171 /* **** PISMO SUPPORT *** */
 172 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 2 sectors */
 173 #define CONFIG_SYS_FLASH_BASE           NAND_BASE
 174
 175 /* Monitor at start of flash */
 176 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_FLASH_BASE
 177 #define CONFIG_SYS_ONENAND_BASE         ONENAND_MAP
 178
 179 #define ONENAND_ENV_OFFSET              0x260000 /* environment starts here */
 180
 181 #define CONFIG_SYS_ENV_SECT_SIZE        (128 << 10)
 182 #define CONFIG_ENV_OFFSET               0x260000
 183 #define CONFIG_ENV_ADDR                 CONFIG_ENV_OFFSET
 184
 185 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
 186 #define CONFIG_SYS_INIT_RAM_ADDR        0x4020f800
 187 #define CONFIG_SYS_INIT_RAM_SIZE        0x800
 188 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_INIT_RAM_ADDR + \
 189                                          CONFIG_SYS_INIT_RAM_SIZE - \
 190                                          GENERATED_GBL_DATA_SIZE)
 191
 192 /*
 193  * USB
 194  *
 195  * Currently only EHCI is enabled, the MUSB OTG controller
 196  * is not enabled.
 197  */
 198
 199 /* USB EHCI */
 200 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO        162
 201
 202 /* Defines for SPL */
 203
 204 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
 205 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
 206
 207 #define CONFIG_SPL_NAND_BASE
 208 #define CONFIG_SPL_NAND_DRIVERS
 209 #define CONFIG_SPL_NAND_ECC
 210
 211 /* NAND boot config */
 212 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 213 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 214 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
 215 #define CONFIG_SYS_NAND_OOBSIZE         64
 216 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 217 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   NAND_LARGE_BADBLOCK_POS
 218 /*
 219  * Use the ECC/OOB layout from omap_gpmc.h that matches your chip:
 220  * SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT
 221  */
 222 #define CONFIG_SYS_NAND_ECCPOS          { 2, 3, 4, 5, 6, 7, 8, 9, \
 223                                          10, 11, 12, 13 }
 224 #define CONFIG_SYS_NAND_ECCSIZE         512
 225 #define CONFIG_SYS_NAND_ECCBYTES        3
 226 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_HAM1_CODE_HW
 227
 228 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 229 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 230
 231 #define CONFIG_SPL_TEXT_BASE            0x40200800
 232 #define CONFIG_SPL_MAX_SIZE             (SRAM_SCRATCH_SPACE_ADDR - \
 233                                          CONFIG_SPL_TEXT_BASE)
 234
 235 /*
 236  * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the
 237  * older x-loader implementations. And move the BSS area so that it
 238  * doesn't overlap with TEXT_BASE.
 239  */
 240 #define CONFIG_SPL_BSS_START_ADDR       0x80100000
 241 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000         /* 512 KB */
 242
 243 #define CONFIG_SYS_SPL_MALLOC_START     0x80208000
 244 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
 245
 246 #endif /* __CONFIG_H */