3 * Stefano Babic, DENX Software Engineering, sbabic@denx.de.
5 * Copyright (C) 2009 TechNexion Ltd.
7 * SPDX-License-Identifier: GPL-2.0+
14 * High Level Configuration Options
16 #define CONFIG_OMAP /* in a TI OMAP core */
17 #define CONFIG_OMAP_GPIO
18 /* Common ARM Erratas */
19 #define CONFIG_ARM_ERRATA_454179
20 #define CONFIG_ARM_ERRATA_430973
21 #define CONFIG_ARM_ERRATA_621766
23 #define CONFIG_SYS_TEXT_BASE 0x80008000
25 #define CONFIG_EMIF4 /* The chip has EMIF4 controller */
27 #include <asm/arch/cpu.h> /* get chip and board defs */
28 #include <asm/arch/omap.h>
31 #define V_OSCK 26000000 /* Clock output from T2 */
32 #define V_SCLK (V_OSCK >> 1)
34 #define CONFIG_MISC_INIT_R
36 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
37 #define CONFIG_SETUP_MEMORY_TAGS
38 #define CONFIG_INITRD_TAG
39 #define CONFIG_REVISION_TAG
42 * Size of malloc() pool
44 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */
45 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10) + \
50 #define CONFIG_OMAP3_MICRON_DDR /* Micron DDR */
51 #define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
58 * NS16550 Configuration
60 #define CONFIG_SYS_NS16550_SERIAL
61 #define CONFIG_SYS_NS16550_REG_SIZE (-4)
62 #define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
65 * select serial console configuration
67 #define CONFIG_CONS_INDEX 1
68 #define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
69 #define CONFIG_SERIAL1 /* UART1 */
71 /* allow to overwrite serial and ethaddr */
72 #define CONFIG_ENV_OVERWRITE
73 #define CONFIG_BAUDRATE 115200
74 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
76 #define CONFIG_GENERIC_MMC
79 #define CONFIG_OMAP3_GPIO_5
80 #define CONFIG_USB_EHCI
81 #define CONFIG_USB_EHCI_OMAP
82 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 25
83 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
85 /* commands to include */
86 #define CONFIG_CMD_NAND /* NAND support */
87 #define CONFIG_CMD_EEPROM
89 #define CONFIG_SYS_NO_FLASH
90 #define CONFIG_SYS_I2C
91 #define CONFIG_SYS_OMAP24_I2C_SPEED 400000
92 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1
93 #define CONFIG_SYS_I2C_OMAP34XX
94 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */
95 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
96 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
101 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
105 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
108 #define CONFIG_AUTO_COMPLETE
111 * Miscellaneous configurable options
113 #define CONFIG_SYS_LONGHELP /* undef to save memory */
114 #define CONFIG_CMDLINE_EDITING
115 #define CONFIG_AUTO_COMPLETE
116 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
118 /* Print Buffer Size */
119 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
120 sizeof(CONFIG_SYS_PROMPT) + 16)
121 #define CONFIG_SYS_MAXARGS 32 /* max number of command */
123 /* Boot Argument Buffer Size */
124 #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
125 /* memtest works on */
126 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
127 #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
128 0x01F00000) /* 31MB */
130 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
134 * AM3517 has 12 GP timers, they can be driven by the system clock
135 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
136 * This rate is divided by a local divisor.
138 #define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
139 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
142 * Physical Memory Map
144 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
145 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
146 #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
149 * FLASH and environment organization
152 /* **** PISMO SUPPORT *** */
154 #define CONFIG_NAND_OMAP_GPMC
155 #define CONFIG_ENV_IS_IN_NAND
156 #define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */
158 /* Redundant Environment */
159 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
160 #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
161 #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
162 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
163 2 * CONFIG_SYS_ENV_SECT_SIZE)
164 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
166 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
167 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
168 #define CONFIG_SYS_INIT_RAM_SIZE 0x800
169 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
170 CONFIG_SYS_INIT_RAM_SIZE - \
171 GENERATED_GBL_DATA_SIZE)
174 * ethernet support, EMAC
177 #define CONFIG_DRIVER_TI_EMAC
178 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
180 #define CONFIG_EMAC_MDIO_PHY_NUM 0
181 #define CONFIG_BOOTP_DNS
182 #define CONFIG_BOOTP_DNS2
183 #define CONFIG_BOOTP_SEND_HOSTNAME
184 #define CONFIG_NET_RETRY_COUNT 10
186 /* Defines for SPL */
187 #define CONFIG_SPL_FRAMEWORK
188 #define CONFIG_SPL_BOARD_INIT
189 #define CONFIG_SPL_CONSOLE
190 #define CONFIG_SPL_NAND_SIMPLE
191 #define CONFIG_SPL_NAND_SOFTECC
192 #define CONFIG_SPL_NAND_WORKSPACE 0x8f07f000 /* below BSS */
194 #define CONFIG_SPL_NAND_BASE
195 #define CONFIG_SPL_NAND_DRIVERS
196 #define CONFIG_SPL_NAND_ECC
197 #define CONFIG_SPL_LDSCRIPT "arch/arm/mach-omap2/u-boot-spl.lds"
199 #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/
200 #define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \
201 CONFIG_SPL_TEXT_BASE)
202 #define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
204 #define CONFIG_SYS_SPL_MALLOC_START 0x8f000000
205 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
206 #define CONFIG_SPL_BSS_START_ADDR 0x8f080000 /* end of RAM */
207 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000
209 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
210 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
213 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
214 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"
216 /* RAW SD card / eMMC */
217 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */
218 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */
219 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */
221 /* NAND boot config */
222 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT
223 #define CONFIG_SYS_NAND_PAGE_COUNT 64
224 #define CONFIG_SYS_NAND_PAGE_SIZE 2048
225 #define CONFIG_SYS_NAND_OOBSIZE 64
226 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
227 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
228 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
229 #define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47,\
230 48, 49, 50, 51, 52, 53, 54, 55,\
231 56, 57, 58, 59, 60, 61, 62, 63}
232 #define CONFIG_SYS_NAND_ECCSIZE 256
233 #define CONFIG_SYS_NAND_ECCBYTES 3
234 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW
235 #define CONFIG_NAND_OMAP_GPMC_PREFETCH
237 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
239 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
240 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000
242 #define CONFIG_CMD_UBIFS
243 #define CONFIG_RBTREE
245 #define CONFIG_MTD_PARTITIONS
246 #define CONFIG_MTD_DEVICE
247 #define CONFIG_CMD_MTDPARTS
249 /* Setup MTD for NAND on the SOM */
250 #define MTDIDS_DEFAULT "nand0=omap2-nand.0"
251 #define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(MLO)," \
252 "1m(u-boot),256k(env1)," \
253 "256k(env2),6m(kernel),-(rootfs)"
255 #define CONFIG_TAM3517_SETTINGS \
257 "nandargs=setenv bootargs root=${nandroot} " \
258 "rootfstype=${nandrootfstype}\0" \
259 "nfsargs=setenv bootargs root=/dev/nfs rw " \
260 "nfsroot=${serverip}:${rootpath}\0" \
261 "ramargs=setenv bootargs root=/dev/ram rw\0" \
262 "addip_sta=setenv bootargs ${bootargs} " \
263 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
264 ":${hostname}:${netdev}:off panic=1\0" \
265 "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \
266 "addip=if test -n ${ipdyn};then run addip_dyn;" \
267 "else run addip_sta;fi\0" \
268 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
269 "addtty=setenv bootargs ${bootargs}" \
270 " console=ttyO0,${baudrate}\0" \
271 "addmisc=setenv bootargs ${bootargs} ${misc}\0" \
272 "loadaddr=82000000\0" \
273 "kernel_addr_r=82000000\0" \
274 "hostname=" __stringify(CONFIG_HOSTNAME) "\0" \
275 "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \
276 "flash_self=run ramargs addip addtty addmtd addmisc;" \
277 "bootm ${kernel_addr} ${ramdisk_addr}\0" \
278 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
279 "bootm ${kernel_addr}\0" \
280 "nandboot=run nandargs addip addtty addmtd addmisc;" \
281 "nand read ${kernel_addr_r} kernel\0" \
282 "bootm ${kernel_addr_r}\0" \
283 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
284 "run nfsargs addip addtty addmtd addmisc;" \
285 "bootm ${kernel_addr_r}\0" \
286 "net_self=if run net_self_load;then " \
287 "run ramargs addip addtty addmtd addmisc;" \
288 "bootm ${kernel_addr_r} ${ramdisk_addr_r};" \
289 "else echo Images not loades;fi\0" \
290 "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.img\0" \
291 "load=tftp ${loadaddr} ${u-boot}\0" \
292 "loadmlo=tftp ${loadaddr} ${mlo}\0" \
293 "mlo=" __stringify(CONFIG_HOSTNAME) "/MLO\0" \
294 "uboot_addr=0x80000\0" \
295 "update=nandecc sw;nand erase ${uboot_addr} 100000;" \
296 "nand write ${loadaddr} ${uboot_addr} 80000\0" \
297 "updatemlo=nandecc hw;nand erase 0 20000;" \
298 "nand write ${loadaddr} 0 20000\0" \
299 "upd=if run load;then echo Updating u-boot;if run update;" \
300 "then echo U-Boot updated;" \
301 "else echo Error updating u-boot !;" \
302 "echo Board without bootloader !!;" \
304 "else echo U-Boot not downloaded..exiting;fi\0" \
307 * this is common code for all TAM3517 boards.
308 * MAC address is stored from manufacturer in
311 #if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))
313 * The I2C EEPROM on the TAM3517 contains
314 * mac address and production data
316 struct tam3517_module_info {
321 * bit 0~47 : sequence number
322 * bit 48~55 : week of year, from 0.
325 unsigned long long sequence_number;
328 * bit 0~7 : revision fixed
329 * bit 8~15 : revision major
332 unsigned int revision;
333 unsigned char eth_addr[4][8];
334 unsigned char _rev[100];
337 #define TAM3517_READ_EEPROM(info, ret) \
339 i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \
340 if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, \
341 (void *)info, sizeof(*info))) \
347 #define TAM3517_READ_MAC_FROM_EEPROM(info) \
349 char buf[80], ethname[20]; \
351 memset(buf, 0, sizeof(buf)); \
352 for (i = 0 ; i < ARRAY_SIZE((info)->eth_addr); i++) { \
353 sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X", \
354 (info)->eth_addr[i][5], \
355 (info)->eth_addr[i][4], \
356 (info)->eth_addr[i][3], \
357 (info)->eth_addr[i][2], \
358 (info)->eth_addr[i][1], \
359 (info)->eth_addr[i][0]); \
362 sprintf(ethname, "eth%daddr", i); \
364 strcpy(ethname, "ethaddr"); \
365 printf("Setting %s from EEPROM with %s\n", ethname, buf);\
366 setenv(ethname, buf); \
370 /* The following macros are taken from Technexion's documentation */
371 #define TAM3517_sequence_number(info) \
372 ((info)->sequence_number % 0x1000000000000LL)
373 #define TAM3517_week_of_year(info) (((info)->sequence_number >> 48) % 0x100)
374 #define TAM3517_year(info) ((info)->sequence_number >> 56)
375 #define TAM3517_revision_fixed(info) ((info)->revision % 0x100)
376 #define TAM3517_revision_major(info) (((info)->revision >> 8) % 0x100)
377 #define TAM3517_revision_tn(info) ((info)->revision >> 16)
379 #define TAM3517_PRINT_SOM_INFO(info) \
381 printf("Vendor:%s\n", (info)->customer); \
382 printf("SOM: %s\n", (info)->product); \
383 printf("SeqNr: %02llu%02llu%012llu\n", \
384 TAM3517_year(info), \
385 TAM3517_week_of_year(info), \
386 TAM3517_sequence_number(info)); \
387 printf("Rev: TN%u %u.%u\n", \
388 TAM3517_revision_tn(info), \
389 TAM3517_revision_major(info), \
390 TAM3517_revision_fixed(info)); \
395 #endif /* __TAM3517_H */