include/configs/tam3517-common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) 2011
   4  * Stefano Babic, DENX Software Engineering, sbabic@denx.de.
   5  *
   6  * Copyright (C) 2009 TechNexion Ltd.
   7  */
   8
   9 #ifndef __TAM3517_H
  10 #define __TAM3517_H
  11
  12 /*
  13  * High Level Configuration Options
  14  */
  15
  16 #include <asm/arch/cpu.h>               /* get chip and board defs */
  17 #include <asm/arch/omap.h>
  18
  19 /* Clock Defines */
  20 #define V_OSCK                  26000000        /* Clock output from T2 */
  21 #define V_SCLK                  (V_OSCK >> 1)
  22
  23 #define CONFIG_MISC_INIT_R
  24
  25 #define CONFIG_CMDLINE_TAG                      /* enable passing of ATAGs */
  26 #define CONFIG_SETUP_MEMORY_TAGS
  27 #define CONFIG_INITRD_TAG
  28 #define CONFIG_REVISION_TAG
  29
  30 /*
  31  * Size of malloc() pool
  32  */
  33 #define CONFIG_ENV_SIZE                 (128 << 10)     /* 128 KiB sector */
  34 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + (128 << 10) + \
  35                                         2 * 1024 * 1024)
  36 /*
  37  * DDR related
  38  */
  39 #define CONFIG_SYS_CS0_SIZE             (256 * 1024 * 1024)
  40
  41 /*
  42  * Hardware drivers
  43  */
  44
  45 /*
  46  * NS16550 Configuration
  47  */
  48 #define CONFIG_SYS_NS16550_SERIAL
  49 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
  50 #define CONFIG_SYS_NS16550_CLK          48000000        /* 48MHz (APLL96/2) */
  51
  52 /*
  53  * select serial console configuration
  54  */
  55 #define CONFIG_SYS_NS16550_COM1         OMAP34XX_UART1
  56 #define CONFIG_SERIAL1                  /* UART1 */
  57
  58 /* allow to overwrite serial and ethaddr */
  59 #define CONFIG_ENV_OVERWRITE
  60 #define CONFIG_SYS_BAUDRATE_TABLE       {4800, 9600, 19200, 38400, 57600,\
  61                                         115200}
  62 /* EHCI */
  63 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO        25
  64
  65 #define CONFIG_SYS_I2C
  66 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50            /* base address */
  67 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1               /* bytes of address */
  68 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW     0x07
  69
  70 /*
  71  * Board NAND Info.
  72  */
  73 #define CONFIG_SYS_NAND_BASE            NAND_BASE       /* physical address */
  74                                                         /* to access */
  75                                                         /* nand at CS0 */
  76
  77 #define CONFIG_SYS_MAX_NAND_DEVICE      1               /* Max number of */
  78                                                         /* NAND devices */
  79
  80 /*
  81  * Miscellaneous configurable options
  82  */
  83 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
  84
  85 #define CONFIG_SYS_MAXARGS              32      /* max number of command */
  86                                                 /* args */
  87 /* memtest works on */
  88 #define CONFIG_SYS_MEMTEST_START        (OMAP34XX_SDRC_CS0)
  89 #define CONFIG_SYS_MEMTEST_END          (OMAP34XX_SDRC_CS0 + \
  90                                         0x01F00000) /* 31MB */
  91
  92 #define CONFIG_SYS_LOAD_ADDR            (OMAP34XX_SDRC_CS0) /* default load */
  93                                                                 /* address */
  94
  95 /*
  96  * AM3517 has 12 GP timers, they can be driven by the system clock
  97  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
  98  * This rate is divided by a local divisor.
  99  */
 100 #define CONFIG_SYS_TIMERBASE            OMAP34XX_GPT2
 101 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
 102
 103 /*
 104  * Physical Memory Map
 105  */
 106 #define CONFIG_NR_DRAM_BANKS    2       /* CS1 may or may not be populated */
 107 #define PHYS_SDRAM_1            OMAP34XX_SDRC_CS0
 108 #define PHYS_SDRAM_2            OMAP34XX_SDRC_CS1
 109
 110 /*
 111  * FLASH and environment organization
 112  */
 113
 114 /* **** PISMO SUPPORT *** */
 115
 116 /* Redundant Environment */
 117 #define CONFIG_SYS_ENV_SECT_SIZE        (128 << 10)     /* 128 KiB */
 118 #define CONFIG_ENV_OFFSET               0x180000
 119 #define CONFIG_ENV_ADDR                 0x180000
 120 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + \
 121                                                 2 * CONFIG_SYS_ENV_SECT_SIZE)
 122 #define CONFIG_ENV_SIZE_REDUND          CONFIG_ENV_SIZE
 123
 124 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
 125 #define CONFIG_SYS_INIT_RAM_ADDR        0x4020f800
 126 #define CONFIG_SYS_INIT_RAM_SIZE        0x800
 127 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_INIT_RAM_ADDR + \
 128                                          CONFIG_SYS_INIT_RAM_SIZE - \
 129                                          GENERATED_GBL_DATA_SIZE)
 130
 131 /*
 132  * ethernet support, EMAC
 133  *
 134  */
 135 #define CONFIG_DRIVER_TI_EMAC
 136 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
 137 #define CONFIG_MII
 138 #define CONFIG_BOOTP_DNS2
 139 #define CONFIG_BOOTP_SEND_HOSTNAME
 140 #define CONFIG_NET_RETRY_COUNT 10
 141
 142 /* Defines for SPL */
 143 #define CONFIG_SPL_CONSOLE
 144 #define CONFIG_SPL_NAND_SOFTECC
 145 #define CONFIG_SPL_NAND_WORKSPACE       0x8f07f000 /* below BSS */
 146
 147 #define CONFIG_SPL_NAND_BASE
 148 #define CONFIG_SPL_NAND_DRIVERS
 149 #define CONFIG_SPL_NAND_ECC
 150
 151 #define CONFIG_SPL_TEXT_BASE            0x40200000 /*CONFIG_SYS_SRAM_START*/
 152 #define CONFIG_SPL_MAX_SIZE             (SRAM_SCRATCH_SPACE_ADDR - \
 153                                          CONFIG_SPL_TEXT_BASE)
 154 #define CONFIG_SPL_STACK                LOW_LEVEL_SRAM_STACK
 155
 156 #define CONFIG_SYS_SPL_MALLOC_START     0x8f000000
 157 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x80000
 158 #define CONFIG_SPL_BSS_START_ADDR       0x8f080000 /* end of RAM */
 159 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 160
 161 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
 162 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME         "u-boot.img"
 163
 164 /* FAT */
 165 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME          "uImage"
 166 #define CONFIG_SPL_FS_LOAD_ARGS_NAME            "args"
 167
 168 /* RAW SD card / eMMC */
 169 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900   /* address 0x120000 */
 170 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR   0x80    /* address 0x10000 */
 171 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS  0x80    /* 64KiB */
 172
 173 /* NAND boot config */
 174 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 175 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
 176 #define CONFIG_SYS_NAND_OOBSIZE         64
 177 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 178 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 179 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
 180 #define CONFIG_SYS_NAND_ECCPOS          {40, 41, 42, 43, 44, 45, 46, 47,\
 181                                          48, 49, 50, 51, 52, 53, 54, 55,\
 182                                          56, 57, 58, 59, 60, 61, 62, 63}
 183 #define CONFIG_SYS_NAND_ECCSIZE         256
 184 #define CONFIG_SYS_NAND_ECCBYTES        3
 185 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_HAM1_CODE_SW
 186
 187 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 188
 189 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 190 #define CONFIG_SYS_NAND_U_BOOT_SIZE     0x80000
 191
 192 /* Setup MTD for NAND on the SOM */
 193
 194 #define CONFIG_TAM3517_SETTINGS                                         \
 195         "netdev=eth0\0"                                                 \
 196         "nandargs=setenv bootargs root=${nandroot} "                    \
 197                 "rootfstype=${nandrootfstype}\0"                        \
 198         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 199                 "nfsroot=${serverip}:${rootpath}\0"                     \
 200         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 201         "addip_sta=setenv bootargs ${bootargs} "                        \
 202                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 203                 ":${hostname}:${netdev}:off panic=1\0"                  \
 204         "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"               \
 205         "addip=if test -n ${ipdyn};then run addip_dyn;"                 \
 206                 "else run addip_sta;fi\0"                               \
 207         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 208         "addtty=setenv bootargs ${bootargs}"                            \
 209                 " console=ttyO0,${baudrate}\0"                          \
 210         "addmisc=setenv bootargs ${bootargs} ${misc}\0"                 \
 211         "loadaddr=82000000\0"                                           \
 212         "kernel_addr_r=82000000\0"                                      \
 213         "hostname=" CONFIG_HOSTNAME "\0"                        \
 214         "bootfile=" CONFIG_HOSTNAME "/uImage\0"         \
 215         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
 216                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 217         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
 218                 "bootm ${kernel_addr}\0"                                \
 219         "nandboot=run nandargs addip addtty addmtd addmisc;"            \
 220                 "nand read ${kernel_addr_r} kernel\0"                   \
 221                 "bootm ${kernel_addr_r}\0"                              \
 222         "net_nfs=tftp ${kernel_addr_r} ${bootfile}; "                   \
 223                 "run nfsargs addip addtty addmtd addmisc;"              \
 224                 "bootm ${kernel_addr_r}\0"                              \
 225         "net_self=if run net_self_load;then "                           \
 226                 "run ramargs addip addtty addmtd addmisc;"              \
 227                 "bootm ${kernel_addr_r} ${ramdisk_addr_r};"             \
 228                 "else echo Images not loades;fi\0"                      \
 229         "u-boot=" CONFIG_HOSTNAME "/u-boot.img\0"               \
 230         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 231         "loadmlo=tftp ${loadaddr} ${mlo}\0"                             \
 232         "mlo=" CONFIG_HOSTNAME "/MLO\0"                 \
 233         "uboot_addr=0x80000\0"                                          \
 234         "update=nandecc sw;nand erase ${uboot_addr} 100000;"            \
 235                 "nand write ${loadaddr} ${uboot_addr} 80000\0"          \
 236         "updatemlo=nandecc hw;nand erase 0 20000;"                      \
 237                 "nand write ${loadaddr} 0 20000\0"                      \
 238         "upd=if run load;then echo Updating u-boot;if run update;"      \
 239                 "then echo U-Boot updated;"                             \
 240                         "else echo Error updating u-boot !;"            \
 241                         "echo Board without bootloader !!;"             \
 242                 "fi;"                                                   \
 243                 "else echo U-Boot not downloaded..exiting;fi\0"         \
 244
 245 /*
 246  * this is common code for all TAM3517 boards.
 247  * MAC address is stored from manufacturer in
 248  * I2C EEPROM
 249  */
 250 #if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))
 251 /*
 252  * The I2C EEPROM on the TAM3517 contains
 253  * mac address and production data
 254  */
 255 struct tam3517_module_info {
 256         char customer[48];
 257         char product[48];
 258
 259         /*
 260          * bit 0~47  : sequence number
 261          * bit 48~55 : week of year, from 0.
 262          * bit 56~63 : year
 263          */
 264         unsigned long long sequence_number;
 265
 266         /*
 267          * bit 0~7   : revision fixed
 268          * bit 8~15  : revision major
 269          * bit 16~31 : TNxxx
 270          */
 271         unsigned int revision;
 272         unsigned char eth_addr[4][8];
 273         unsigned char _rev[100];
 274 };
 275
 276 #define TAM3517_READ_EEPROM(info, ret) \
 277 do {                                                            \
 278         i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \
 279         if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,          \
 280                 (void *)info, sizeof(*info)))                   \
 281                 ret = 1;                                        \
 282         else                                                    \
 283                 ret = 0;                                        \
 284 } while (0)
 285
 286 #define TAM3517_READ_MAC_FROM_EEPROM(info)                      \
 287 do {                                                            \
 288         char buf[80], ethname[20];                              \
 289         int i;                                                  \
 290         memset(buf, 0, sizeof(buf));                            \
 291         for (i = 0 ; i < ARRAY_SIZE((info)->eth_addr); i++) {   \
 292                 sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X",   \
 293                         (info)->eth_addr[i][5],                 \
 294                         (info)->eth_addr[i][4],                 \
 295                         (info)->eth_addr[i][3],                 \
 296                         (info)->eth_addr[i][2],                 \
 297                         (info)->eth_addr[i][1],                 \
 298                         (info)->eth_addr[i][0]);                        \
 299                                                                 \
 300                 if (i)                                          \
 301                         sprintf(ethname, "eth%daddr", i);       \
 302                 else                                            \
 303                         strcpy(ethname, "ethaddr");             \
 304                 printf("Setting %s from EEPROM with %s\n", ethname, buf);\
 305                 env_set(ethname, buf);                          \
 306         }                                                       \
 307 } while (0)
 308
 309 /* The following macros are taken from Technexion's documentation */
 310 #define TAM3517_sequence_number(info) \
 311         ((info)->sequence_number % 0x1000000000000LL)
 312 #define TAM3517_week_of_year(info) (((info)->sequence_number >> 48) % 0x100)
 313 #define TAM3517_year(info) ((info)->sequence_number >> 56)
 314 #define TAM3517_revision_fixed(info) ((info)->revision % 0x100)
 315 #define TAM3517_revision_major(info) (((info)->revision >> 8) % 0x100)
 316 #define TAM3517_revision_tn(info) ((info)->revision >> 16)
 317
 318 #define TAM3517_PRINT_SOM_INFO(info)                            \
 319 do {                                                            \
 320         printf("Vendor:%s\n", (info)->customer);                \
 321         printf("SOM:   %s\n", (info)->product);                 \
 322         printf("SeqNr: %02llu%02llu%012llu\n",                  \
 323                 TAM3517_year(info),                             \
 324                 TAM3517_week_of_year(info),                     \
 325                 TAM3517_sequence_number(info));                 \
 326         printf("Rev:   TN%u %u.%u\n",                           \
 327                 TAM3517_revision_tn(info),                      \
 328                 TAM3517_revision_major(info),                   \
 329                 TAM3517_revision_fixed(info));                  \
 330 } while (0)
 331
 332 #endif
 333
 334 #endif /* __TAM3517_H */