3 * Stefano Babic, DENX Software Engineering, sbabic@denx.de.
5 * Copyright (C) 2009 TechNexion Ltd.
7 * SPDX-License-Identifier: GPL-2.0+
14 * High Level Configuration Options
17 #include <asm/arch/cpu.h> /* get chip and board defs */
18 #include <asm/arch/omap.h>
21 #define V_OSCK 26000000 /* Clock output from T2 */
22 #define V_SCLK (V_OSCK >> 1)
24 #define CONFIG_MISC_INIT_R
26 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
27 #define CONFIG_SETUP_MEMORY_TAGS
28 #define CONFIG_INITRD_TAG
29 #define CONFIG_REVISION_TAG
32 * Size of malloc() pool
34 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */
35 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10) + \
40 #define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
47 * NS16550 Configuration
49 #define CONFIG_SYS_NS16550_SERIAL
50 #define CONFIG_SYS_NS16550_REG_SIZE (-4)
51 #define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
54 * select serial console configuration
56 #define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
57 #define CONFIG_SERIAL1 /* UART1 */
59 /* allow to overwrite serial and ethaddr */
60 #define CONFIG_ENV_OVERWRITE
61 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
64 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 25
66 #define CONFIG_SYS_I2C
67 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */
68 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
69 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
74 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
78 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
82 * Miscellaneous configurable options
84 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
86 #define CONFIG_SYS_MAXARGS 32 /* max number of command */
88 /* memtest works on */
89 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
90 #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
91 0x01F00000) /* 31MB */
93 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
97 * AM3517 has 12 GP timers, they can be driven by the system clock
98 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
99 * This rate is divided by a local divisor.
101 #define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
102 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
105 * Physical Memory Map
107 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
108 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
109 #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
112 * FLASH and environment organization
115 /* **** PISMO SUPPORT *** */
117 /* Redundant Environment */
118 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
119 #define CONFIG_ENV_OFFSET 0x180000
120 #define CONFIG_ENV_ADDR 0x180000
121 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
122 2 * CONFIG_SYS_ENV_SECT_SIZE)
123 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
125 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
126 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
127 #define CONFIG_SYS_INIT_RAM_SIZE 0x800
128 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
129 CONFIG_SYS_INIT_RAM_SIZE - \
130 GENERATED_GBL_DATA_SIZE)
133 * ethernet support, EMAC
136 #define CONFIG_DRIVER_TI_EMAC
137 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
139 #define CONFIG_BOOTP_DNS2
140 #define CONFIG_BOOTP_SEND_HOSTNAME
141 #define CONFIG_NET_RETRY_COUNT 10
143 /* Defines for SPL */
144 #define CONFIG_SPL_CONSOLE
145 #define CONFIG_SPL_NAND_SOFTECC
146 #define CONFIG_SPL_NAND_WORKSPACE 0x8f07f000 /* below BSS */
148 #define CONFIG_SPL_NAND_BASE
149 #define CONFIG_SPL_NAND_DRIVERS
150 #define CONFIG_SPL_NAND_ECC
152 #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/
153 #define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \
154 CONFIG_SPL_TEXT_BASE)
155 #define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
157 #define CONFIG_SYS_SPL_MALLOC_START 0x8f000000
158 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
159 #define CONFIG_SPL_BSS_START_ADDR 0x8f080000 /* end of RAM */
160 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000
162 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
163 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
166 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
167 #define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"
169 /* RAW SD card / eMMC */
170 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */
171 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */
172 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */
174 /* NAND boot config */
175 #define CONFIG_SYS_NAND_PAGE_COUNT 64
176 #define CONFIG_SYS_NAND_PAGE_SIZE 2048
177 #define CONFIG_SYS_NAND_OOBSIZE 64
178 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
179 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
180 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
181 #define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47,\
182 48, 49, 50, 51, 52, 53, 54, 55,\
183 56, 57, 58, 59, 60, 61, 62, 63}
184 #define CONFIG_SYS_NAND_ECCSIZE 256
185 #define CONFIG_SYS_NAND_ECCBYTES 3
186 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW
188 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
190 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
191 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000
193 #define CONFIG_MTD_PARTITIONS
194 #define CONFIG_MTD_DEVICE
196 /* Setup MTD for NAND on the SOM */
198 #define CONFIG_TAM3517_SETTINGS \
200 "nandargs=setenv bootargs root=${nandroot} " \
201 "rootfstype=${nandrootfstype}\0" \
202 "nfsargs=setenv bootargs root=/dev/nfs rw " \
203 "nfsroot=${serverip}:${rootpath}\0" \
204 "ramargs=setenv bootargs root=/dev/ram rw\0" \
205 "addip_sta=setenv bootargs ${bootargs} " \
206 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
207 ":${hostname}:${netdev}:off panic=1\0" \
208 "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \
209 "addip=if test -n ${ipdyn};then run addip_dyn;" \
210 "else run addip_sta;fi\0" \
211 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
212 "addtty=setenv bootargs ${bootargs}" \
213 " console=ttyO0,${baudrate}\0" \
214 "addmisc=setenv bootargs ${bootargs} ${misc}\0" \
215 "loadaddr=82000000\0" \
216 "kernel_addr_r=82000000\0" \
217 "hostname=" __stringify(CONFIG_HOSTNAME) "\0" \
218 "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \
219 "flash_self=run ramargs addip addtty addmtd addmisc;" \
220 "bootm ${kernel_addr} ${ramdisk_addr}\0" \
221 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
222 "bootm ${kernel_addr}\0" \
223 "nandboot=run nandargs addip addtty addmtd addmisc;" \
224 "nand read ${kernel_addr_r} kernel\0" \
225 "bootm ${kernel_addr_r}\0" \
226 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
227 "run nfsargs addip addtty addmtd addmisc;" \
228 "bootm ${kernel_addr_r}\0" \
229 "net_self=if run net_self_load;then " \
230 "run ramargs addip addtty addmtd addmisc;" \
231 "bootm ${kernel_addr_r} ${ramdisk_addr_r};" \
232 "else echo Images not loades;fi\0" \
233 "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.img\0" \
234 "load=tftp ${loadaddr} ${u-boot}\0" \
235 "loadmlo=tftp ${loadaddr} ${mlo}\0" \
236 "mlo=" __stringify(CONFIG_HOSTNAME) "/MLO\0" \
237 "uboot_addr=0x80000\0" \
238 "update=nandecc sw;nand erase ${uboot_addr} 100000;" \
239 "nand write ${loadaddr} ${uboot_addr} 80000\0" \
240 "updatemlo=nandecc hw;nand erase 0 20000;" \
241 "nand write ${loadaddr} 0 20000\0" \
242 "upd=if run load;then echo Updating u-boot;if run update;" \
243 "then echo U-Boot updated;" \
244 "else echo Error updating u-boot !;" \
245 "echo Board without bootloader !!;" \
247 "else echo U-Boot not downloaded..exiting;fi\0" \
250 * this is common code for all TAM3517 boards.
251 * MAC address is stored from manufacturer in
254 #if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))
256 * The I2C EEPROM on the TAM3517 contains
257 * mac address and production data
259 struct tam3517_module_info {
264 * bit 0~47 : sequence number
265 * bit 48~55 : week of year, from 0.
268 unsigned long long sequence_number;
271 * bit 0~7 : revision fixed
272 * bit 8~15 : revision major
275 unsigned int revision;
276 unsigned char eth_addr[4][8];
277 unsigned char _rev[100];
280 #define TAM3517_READ_EEPROM(info, ret) \
282 i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \
283 if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, \
284 (void *)info, sizeof(*info))) \
290 #define TAM3517_READ_MAC_FROM_EEPROM(info) \
292 char buf[80], ethname[20]; \
294 memset(buf, 0, sizeof(buf)); \
295 for (i = 0 ; i < ARRAY_SIZE((info)->eth_addr); i++) { \
296 sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X", \
297 (info)->eth_addr[i][5], \
298 (info)->eth_addr[i][4], \
299 (info)->eth_addr[i][3], \
300 (info)->eth_addr[i][2], \
301 (info)->eth_addr[i][1], \
302 (info)->eth_addr[i][0]); \
305 sprintf(ethname, "eth%daddr", i); \
307 strcpy(ethname, "ethaddr"); \
308 printf("Setting %s from EEPROM with %s\n", ethname, buf);\
309 env_set(ethname, buf); \
313 /* The following macros are taken from Technexion's documentation */
314 #define TAM3517_sequence_number(info) \
315 ((info)->sequence_number % 0x1000000000000LL)
316 #define TAM3517_week_of_year(info) (((info)->sequence_number >> 48) % 0x100)
317 #define TAM3517_year(info) ((info)->sequence_number >> 56)
318 #define TAM3517_revision_fixed(info) ((info)->revision % 0x100)
319 #define TAM3517_revision_major(info) (((info)->revision >> 8) % 0x100)
320 #define TAM3517_revision_tn(info) ((info)->revision >> 16)
322 #define TAM3517_PRINT_SOM_INFO(info) \
324 printf("Vendor:%s\n", (info)->customer); \
325 printf("SOM: %s\n", (info)->product); \
326 printf("SeqNr: %02llu%02llu%012llu\n", \
327 TAM3517_year(info), \
328 TAM3517_week_of_year(info), \
329 TAM3517_sequence_number(info)); \
330 printf("Rev: TN%u %u.%u\n", \
331 TAM3517_revision_tn(info), \
332 TAM3517_revision_major(info), \
333 TAM3517_revision_fixed(info)); \
338 #endif /* __TAM3517_H */