3 * Stefan Roese, DENX Software Engineering, sr@denx.de.
5 * SPDX-License-Identifier: GPL-2.0+
9 * t3corp.h - configuration for T3CORP (460GT)
15 * High Level Configuration Options
17 #define CONFIG_460GT 1 /* Specific PPC460GT */
19 #define CONFIG_4xx 1 /* ... PPC4xx family */
21 #ifndef CONFIG_SYS_TEXT_BASE
22 #define CONFIG_SYS_TEXT_BASE 0xFFFA0000
25 #define CONFIG_HOSTNAME t3corp
28 * Include common defines/options for all AMCC/APM eval boards
30 #include "amcc-common.h"
32 #define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */
34 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
35 #define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */
36 #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
37 #define CONFIG_BOARD_TYPES 1 /* support board types */
39 #define CFG_ALT_MEMTEST
42 * Base addresses -- Note these are effective addresses where the
43 * actual resources get mapped (not physical addresses)
45 #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
46 #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
47 #define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE
49 #define CONFIG_SYS_PCIE_MEMBASE 0xb0000000 /* mapped PCIe mem */
50 #define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* incr for PCIe */
51 #define CONFIG_SYS_PCIE_BASE 0xc4000000 /* PCIe UTL regs */
53 #define CONFIG_SYS_PCIE0_CFGBASE 0xc0000000
54 #define CONFIG_SYS_PCIE1_CFGBASE 0xc1000000
55 #define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000
56 #define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000
58 #define CONFIG_SYS_PCIE0_UTLBASE 0xc08010000ULL /* 36bit phys addr */
60 /* base address of inbound PCIe window */
61 #define CONFIG_SYS_PCIE_INBOUND_BASE 0x000000000ULL /* 36bit phys addr */
64 #define CONFIG_SYS_FLASH_BASE 0xFC000000 /* later mapped here */
65 #define CONFIG_SYS_FLASH_SIZE (64 << 20)
67 #define CONFIG_SYS_FPGA1_BASE 0xe0000000
68 #define CONFIG_SYS_FPGA2_BASE 0xe2000000
69 #define CONFIG_SYS_FPGA3_BASE 0xe4000000
71 #define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space */
72 #define CONFIG_SYS_FLASH_BASE_PHYS_H 0x4
73 #define CONFIG_SYS_FLASH_BASE_PHYS_L 0xCC000000
74 #define CONFIG_SYS_FLASH_BASE_PHYS \
75 (((u64)CONFIG_SYS_FLASH_BASE_PHYS_H << 32) \
76 | (u64)CONFIG_SYS_FLASH_BASE_PHYS_L)
78 #define CONFIG_SYS_OCM_BASE 0xE7000000 /* OCM: 64k */
79 #define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */
80 #define CONFIG_SYS_SRAM_SIZE (256 << 10)
81 #define CONFIG_SYS_LOCAL_CONF_REGS 0xEF000000
84 * Initial RAM & stack pointer (placed in OCM)
86 #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
87 #define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
88 #define CONFIG_SYS_GBL_DATA_OFFSET \
89 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
90 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
95 #define CONFIG_CONS_INDEX 1 /* Use UART0 */
101 * Define here the location of the environment variables (flash).
103 #define CONFIG_ENV_IS_IN_FLASH /* use flash for environment vars */
108 #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
109 #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
110 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
111 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
112 #define CONFIG_SYS_CFI_FLASH_STATUS_POLL /* use status poll method */
113 #define CONFIG_SYS_FLASH_PROTECTION /* use hardware flash protection */
115 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, \
116 (CONFIG_SYS_FPGA1_BASE + 0x01000000) }
117 #define CONFIG_SYS_CFI_FLASH_CONFIG_REGS { 0xffff, /* don't set */ \
118 0xbddf } /* set async read mode */
119 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of memory banks */
120 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sectors p. chip*/
122 #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase/ms*/
123 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write/ms*/
125 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buff'd writes (20x faster)*/
126 #define CONFIG_SYS_FLASH_EMPTY_INFO /* 'E' for empty sector on flinfo */
128 #define CONFIG_ENV_SECT_SIZE 0x20000 /* sector size */
129 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - \
130 CONFIG_ENV_SECT_SIZE)
131 #define CONFIG_ENV_SIZE 0x4000 /* env sector size */
133 /* Address and size of Redundant Environment Sector */
134 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
135 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
140 #define CONFIG_SYS_MBYTES_SDRAM 256
141 #define CONFIG_DDR_ECC
142 #define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */
143 #define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */
144 #define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */
145 #undef CONFIG_PPC4xx_DDR_METHOD_A
146 #define CONFIG_DDR_RFDC_FIXED 0x000001D7 /* optimal value */
148 /* DDR1/2 SDRAM Device Control Register Data Values */
150 #define CONFIG_SYS_SDRAM_R0BAS (SDRAM_RXBAS_SDBA_ENCODE(0) | \
151 SDRAM_RXBAS_SDSZ_256)
152 #define CONFIG_SYS_SDRAM_R1BAS 0x00000000
153 #define CONFIG_SYS_SDRAM_R2BAS 0x00000000
154 #define CONFIG_SYS_SDRAM_R3BAS 0x00000000
155 #define CONFIG_SYS_SDRAM_PLBADDULL 0x00000000
156 #define CONFIG_SYS_SDRAM_PLBADDUHB 0x00000008
157 #define CONFIG_SYS_SDRAM_CONF1LL 0x80001C00
158 #define CONFIG_SYS_SDRAM_CONF1HB 0x80001C80
159 #define CONFIG_SYS_SDRAM_CONFPATHB 0x10a68000
161 #define CAS_LATENCY JEDEC_MA_MR_CL_DDR2_5_0_CLK
163 /* DDR1/2 SDRAM Device Control Register Data Values */
164 #define CONFIG_SYS_SDRAM0_MB0CF (SDRAM_RXBAS_SDAM_MODE7 | \
165 SDRAM_RXBAS_SDBE_ENABLE)
166 #define CONFIG_SYS_SDRAM0_MB1CF SDRAM_RXBAS_SDBE_DISABLE
167 #define CONFIG_SYS_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE
168 #define CONFIG_SYS_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE
169 #define CONFIG_SYS_SDRAM0_MCOPT1 (SDRAM_MCOPT1_MCHK_GEN | \
170 SDRAM_MCOPT1_PMU_OPEN | \
171 SDRAM_MCOPT1_DMWD_32 | \
172 SDRAM_MCOPT1_8_BANKS | \
173 SDRAM_MCOPT1_DDR2_TYPE | \
174 SDRAM_MCOPT1_QDEP | \
175 SDRAM_MCOPT1_RWOO_DISABLED | \
176 SDRAM_MCOPT1_WOOO_DISABLED | \
177 SDRAM_MCOPT1_DREF_NORMAL)
178 #define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000
179 #define CONFIG_SYS_SDRAM0_MODT0 SDRAM_MODT_EB0W_ENABLE
180 #define CONFIG_SYS_SDRAM0_MODT1 0x00000000
181 #define CONFIG_SYS_SDRAM0_MODT2 0x00000000
182 #define CONFIG_SYS_SDRAM0_MODT3 0x00000000
183 #define CONFIG_SYS_SDRAM0_CODT (SDRAM_CODT_RK0R_ON | \
184 SDRAM_CODT_DQS_1_8_V_DDR2 | \
186 #define CONFIG_SYS_SDRAM0_RTR SDRAM_RTR_RINT_ENCODE(1560)
187 #define CONFIG_SYS_SDRAM0_INITPLR0 \
188 (SDRAM_INITPLR_ENABLE | \
189 SDRAM_INITPLR_IMWT_ENCODE(80) | \
190 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_NOP))
191 #define CONFIG_SYS_SDRAM0_INITPLR1 \
192 (SDRAM_INITPLR_ENABLE | \
193 SDRAM_INITPLR_IMWT_ENCODE(3) | \
194 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \
195 SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \
196 SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL))
197 #define CONFIG_SYS_SDRAM0_INITPLR2 \
198 (SDRAM_INITPLR_ENABLE | \
199 SDRAM_INITPLR_IMWT_ENCODE(2) | \
200 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
201 SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR2) | \
202 SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR2_TEMP_COMMERCIAL))
203 #define CONFIG_SYS_SDRAM0_INITPLR3 \
204 (SDRAM_INITPLR_ENABLE | \
205 SDRAM_INITPLR_IMWT_ENCODE(2) | \
206 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
207 SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR3) | \
208 SDRAM_INITPLR_IMA_ENCODE(0))
209 #define CONFIG_SYS_SDRAM0_INITPLR4 \
210 (SDRAM_INITPLR_ENABLE | \
211 SDRAM_INITPLR_IMWT_ENCODE(2) | \
212 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
213 SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \
214 SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_DQS_ENABLE | \
215 JEDEC_MA_EMR_RTT_150OHM))
216 #define CONFIG_SYS_SDRAM0_INITPLR5 \
217 (SDRAM_INITPLR_ENABLE | \
218 SDRAM_INITPLR_IMWT_ENCODE(200) | \
219 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
220 SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \
221 SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \
223 JEDEC_MA_MR_BLEN_4 | \
224 JEDEC_MA_MR_DLL_RESET))
225 #define CONFIG_SYS_SDRAM0_INITPLR6 \
226 (SDRAM_INITPLR_ENABLE | \
227 SDRAM_INITPLR_IMWT_ENCODE(3) | \
228 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \
229 SDRAM_INITPLR_IBA_ENCODE(0x0) | \
230 SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL))
231 #define CONFIG_SYS_SDRAM0_INITPLR7 \
232 (SDRAM_INITPLR_ENABLE | \
233 SDRAM_INITPLR_IMWT_ENCODE(26) | \
234 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
235 #define CONFIG_SYS_SDRAM0_INITPLR8 \
236 (SDRAM_INITPLR_ENABLE | \
237 SDRAM_INITPLR_IMWT_ENCODE(26) | \
238 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
239 #define CONFIG_SYS_SDRAM0_INITPLR9 \
240 (SDRAM_INITPLR_ENABLE | \
241 SDRAM_INITPLR_IMWT_ENCODE(26) | \
242 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
243 #define CONFIG_SYS_SDRAM0_INITPLR10 \
244 (SDRAM_INITPLR_ENABLE | \
245 SDRAM_INITPLR_IMWT_ENCODE(26) | \
246 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
247 #define CONFIG_SYS_SDRAM0_INITPLR11 \
248 (SDRAM_INITPLR_ENABLE | \
249 SDRAM_INITPLR_IMWT_ENCODE(2) | \
250 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
251 SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \
252 SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \
255 #define CONFIG_SYS_SDRAM0_INITPLR12 \
256 (SDRAM_INITPLR_ENABLE | \
257 SDRAM_INITPLR_IMWT_ENCODE(2) | \
258 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
259 SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \
260 SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_OCD_ENTER | \
261 JEDEC_MA_EMR_RDQS_DISABLE | \
262 JEDEC_MA_EMR_DQS_ENABLE | \
263 JEDEC_MA_EMR_RTT_150OHM | \
264 JEDEC_MA_EMR_ODS_NORMAL))
265 #define CONFIG_SYS_SDRAM0_INITPLR13 \
266 (SDRAM_INITPLR_ENABLE | \
267 SDRAM_INITPLR_IMWT_ENCODE(2) | \
268 SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
269 SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \
270 SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_OCD_EXIT | \
271 JEDEC_MA_EMR_RDQS_DISABLE | \
272 JEDEC_MA_EMR_DQS_ENABLE | \
273 JEDEC_MA_EMR_RTT_150OHM | \
274 JEDEC_MA_EMR_ODS_NORMAL))
275 #define CONFIG_SYS_SDRAM0_INITPLR14 SDRAM_INITPLR_DISABLE
276 #define CONFIG_SYS_SDRAM0_INITPLR15 SDRAM_INITPLR_DISABLE
277 #define CONFIG_SYS_SDRAM0_RQDC (SDRAM_RQDC_RQDE_ENABLE | \
278 SDRAM_RQDC_RQFD_ENCODE(56))
279 #define CONFIG_SYS_SDRAM0_RFDC SDRAM_RFDC_RFFD_ENCODE(599)
280 #define CONFIG_SYS_SDRAM0_RDCC (SDRAM_RDCC_RDSS_T2)
281 #define CONFIG_SYS_SDRAM0_DLCR (SDRAM_DLCR_DCLM_AUTO | \
282 SDRAM_DLCR_DLCS_CONT_DONE | \
283 SDRAM_DLCR_DLCV_ENCODE(155))
284 #define CONFIG_SYS_SDRAM0_CLKTR SDRAM_CLKTR_CLKP_90_DEG_ADV
285 #define CONFIG_SYS_SDRAM0_WRDTR SDRAM_WRDTR_WTR_90_DEG_ADV
286 #define CONFIG_SYS_SDRAM0_SDTR1 (SDRAM_SDTR1_LDOF_2_CLK | \
287 SDRAM_SDTR1_RTW_2_CLK | \
288 SDRAM_SDTR1_RTRO_1_CLK)
289 #define CONFIG_SYS_SDRAM0_SDTR2 (SDRAM_SDTR2_RCD_3_CLK | \
290 SDRAM_SDTR2_WTR_2_CLK | \
291 SDRAM_SDTR2_XSNR_32_CLK | \
292 SDRAM_SDTR2_WPC_4_CLK | \
293 SDRAM_SDTR2_RPC_2_CLK | \
294 SDRAM_SDTR2_RP_3_CLK | \
295 SDRAM_SDTR2_RRD_2_CLK)
296 #define CONFIG_SYS_SDRAM0_SDTR3 (SDRAM_SDTR3_RAS_ENCODE(8) | \
297 SDRAM_SDTR3_RC_ENCODE(11) | \
299 SDRAM_SDTR3_RFC_ENCODE(26))
300 #define CONFIG_SYS_SDRAM0_MMODE (SDRAM_MMODE_WR_DDR2_3_CYC | \
303 #define CONFIG_SYS_SDRAM0_MEMODE (SDRAM_MEMODE_DQS_ENABLE | \
304 SDRAM_MEMODE_RTT_150OHM)
309 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
311 #define CONFIG_SYS_I2C_MULTI_EEPROMS
312 #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
313 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
314 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
315 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
317 /* I2C bootstrap EEPROM */
318 #define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x52
319 #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
320 #define CONFIG_4xx_CONFIG_BLOCKSIZE 16
325 #define CONFIG_IBM_EMAC4_V4 1
327 #define CONFIG_HAS_ETH0
329 #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
330 #define CONFIG_M88E1111_PHY
331 /* Disable fiber since fiber/copper auto-selection doesn't seem to work */
332 #define CONFIG_M88E1111_DISABLE_FIBER
334 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */
335 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
336 #define CONFIG_PHY_DYNAMIC_ANEG 1
339 * Default environment variables
341 #define CONFIG_EXTRA_ENV_SETTINGS \
342 CONFIG_AMCC_DEF_ENV \
343 CONFIG_AMCC_DEF_ENV_POWERPC \
344 CONFIG_AMCC_DEF_ENV_NOR_UPD \
345 "kernel_addr=fc000000\0" \
346 "fdt_addr=fc1e0000\0" \
347 "ramdisk_addr=fc200000\0" \
348 "pciconfighost=1\0" \
349 "pcie_mode=RP:RP\0" \
354 * Commands additional to the ones defined in amcc-common.h
356 #define CONFIG_CMD_CHIP_CONFIG
357 #define CONFIG_CMD_ECCTEST
358 #define CONFIG_CMD_PCI
359 #define CONFIG_CMD_SDRAM
365 #define CONFIG_PCI /* include pci support */
366 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
367 #define CONFIG_PCI_PNP /* do pci plug-and-play */
368 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
369 #define CONFIG_PCI_CONFIG_HOST_BRIDGE
371 /* Board-specific PCI, no PCI support, only PCIe */
372 #undef CONFIG_SYS_PCI_TARGET_INIT
373 #undef CONFIG_SYS_PCI_MASTER_INIT
375 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
376 #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
380 * External Bus Controller (EBC) Setup
384 * T3CORP has 64MBytes of NOR flash (Spansion 29GL512), but the
385 * boot EBC mapping only supports a maximum of 16MBytes
386 * (4.ff00.0000 - 4.ffff.ffff).
387 * To solve this problem, the flash has to get remapped to another
388 * EBC address which accepts bigger regions:
390 * 0xfc00.0000 -> 4.cc00.0000
393 /* Memory Bank 0 (NOR-flash) */
394 #define CONFIG_SYS_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \
395 EBC_BXAP_TWT_ENCODE(16) | \
396 EBC_BXAP_BCE_DISABLE | \
397 EBC_BXAP_BCT_2TRANS | \
398 EBC_BXAP_CSN_ENCODE(1) | \
399 EBC_BXAP_OEN_ENCODE(1) | \
400 EBC_BXAP_WBN_ENCODE(1) | \
401 EBC_BXAP_WBF_ENCODE(1) | \
402 EBC_BXAP_TH_ENCODE(7) | \
403 EBC_BXAP_RE_DISABLED | \
404 EBC_BXAP_SOR_DELAYED | \
405 EBC_BXAP_BEM_WRITEONLY | \
406 EBC_BXAP_PEN_DISABLED)
407 #define CONFIG_SYS_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_BOOT_BASE_ADDR) | \
412 /* Memory Bank 1 (FPGA 1) */
413 #define CONFIG_SYS_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \
414 EBC_BXAP_TWT_ENCODE(5) | \
415 EBC_BXAP_CSN_ENCODE(0) | \
416 EBC_BXAP_OEN_ENCODE(3) | \
417 EBC_BXAP_WBN_ENCODE(0) | \
418 EBC_BXAP_WBF_ENCODE(0) | \
419 EBC_BXAP_TH_ENCODE(1) | \
420 EBC_BXAP_RE_ENABLED | \
421 EBC_BXAP_SOR_DELAYED | \
423 EBC_BXAP_PEN_DISABLED)
424 #define CONFIG_SYS_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FPGA1_BASE) | \
429 /* Memory Bank 2 (FPGA 2) */
430 #define CONFIG_SYS_EBC_PB2AP (EBC_BXAP_BME_DISABLED | \
431 EBC_BXAP_TWT_ENCODE(5) | \
432 EBC_BXAP_CSN_ENCODE(0) | \
433 EBC_BXAP_OEN_ENCODE(3) | \
434 EBC_BXAP_WBN_ENCODE(0) | \
435 EBC_BXAP_WBF_ENCODE(0) | \
436 EBC_BXAP_TH_ENCODE(1) | \
437 EBC_BXAP_RE_ENABLED | \
438 EBC_BXAP_SOR_DELAYED | \
440 EBC_BXAP_PEN_DISABLED)
441 #define CONFIG_SYS_EBC_PB2CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FPGA2_BASE) | \
446 /* Memory Bank 3 (FPGA 3) */
447 #define CONFIG_SYS_EBC_PB3AP (EBC_BXAP_BME_DISABLED | \
448 EBC_BXAP_TWT_ENCODE(5) | \
449 EBC_BXAP_CSN_ENCODE(0) | \
450 EBC_BXAP_OEN_ENCODE(3) | \
451 EBC_BXAP_WBN_ENCODE(0) | \
452 EBC_BXAP_WBF_ENCODE(0) | \
453 EBC_BXAP_TH_ENCODE(1) | \
454 EBC_BXAP_RE_ENABLED | \
455 EBC_BXAP_SOR_DELAYED | \
457 EBC_BXAP_PEN_DISABLED)
458 #define CONFIG_SYS_EBC_PB3CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FPGA3_BASE) | \
464 * PPC4xx GPIO Configuration
467 #define CONFIG_SYS_4xx_GPIO_TABLE { /* GPIO Alternate1 Alternate2 Alternate3 */ \
470 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \
471 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 GMC1TxD(1) USB2HostD(1) */ \
472 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 GMC1TxD(2) USB2HostD(2) */ \
473 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 GMC1TxD(3) USB2HostD(3) */ \
474 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 GMC1TxD(4) USB2HostD(4) */ \
475 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 GMC1TxD(5) USB2HostD(5) */ \
476 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 GMC1TxD(6) USB2HostD(6) */ \
477 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 GMC1TxD(7) USB2HostD(7) */ \
478 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 GMC1RxD(0) USB2OTGD(0) */ \
479 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 GMC1RxD(1) USB2OTGD(1) */ \
480 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 GMC1RxD(2) USB2OTGD(2) */ \
481 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 GMC1RxD(3) USB2OTGD(3) */ \
482 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO12 GMC1RxD(4) USB2OTGD(4) */ \
483 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO13 GMC1RxD(5) USB2OTGD(5) */ \
484 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO14 GMC1RxD(6) USB2OTGD(6) */ \
485 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO15 GMC1RxD(7) USB2OTGD(7) */ \
486 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 GMC1TxER USB2HostStop */ \
487 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMC1CD USB2HostNext */ \
488 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMC1RxER USB2HostDir */ \
489 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 GMC1TxEN USB2OTGStop */ \
490 {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 GMC1CRS USB2OTGNext */ \
491 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 GMC1RxDV USB2OTGDir */ \
492 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO22 NFRDY */ \
493 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 NFREN */ \
494 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 NFWEN */ \
495 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 NFCLE */ \
496 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 NFALE */ \
497 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO27 IRQ(0) */ \
498 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO28 IRQ(1) */ \
499 {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2) */ \
500 {GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO30 PerPar0 DMAReq2 IRQ(7)*/ \
501 {GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO31 PerPar1 DMAAck2 IRQ(8)*/ \
505 {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 PerPar2 EOT2/TC2 IRQ(9)*/ \
506 {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 PerPar3 DMAReq3 IRQ(4)*/ \
507 {GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_1}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
508 {GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
509 {GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N DMAAck3 UART3_SIN*/ \
510 {GPIO1_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EOT3/TC3 UART3_SOUT*/ \
511 {GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \
512 {GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \
513 {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 IRQ(3) */ \
514 {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 CS(1) */ \
515 {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 CS(2) */ \
516 {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \
517 {GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO44 CS(4) DMAAck1 IRQ(11)*/ \
518 {GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO45 CS(5) EOT/TC1 IRQ(12)*/ \
519 {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 PerAddr(5) DMAReq0 IRQ(13)*/ \
520 {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 PerAddr(6) DMAAck0 IRQ(14)*/ \
521 {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 PerAddr(7) EOT/TC0 IRQ(15)*/ \
522 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \
523 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \
524 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \
525 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \
526 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \
527 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \
528 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \
529 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \
530 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \
531 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \
532 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \
533 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \
534 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \
535 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \
536 {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
540 #endif /* __CONFIG_H */