include/configs/socrates.h

   1 /*
   2  * (C) Copyright 2008
   3  * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com.
   4  *
   5  * Wolfgang Denk <wd@denx.de>
   6  * Copyright 2004 Freescale Semiconductor.
   7  * (C) Copyright 2002,2003 Motorola,Inc.
   8  * Xianghua Xiao <X.Xiao@motorola.com>
   9  *
  10  * SPDX-License-Identifier:     GPL-2.0+
  11  */
  12
  13 /*
  14  * Socrates
  15  */
  16
  17 #ifndef __CONFIG_H
  18 #define __CONFIG_H
  19
  20 /* High Level Configuration Options */
  21 #define CONFIG_BOOKE            1       /* BOOKE                        */
  22 #define CONFIG_E500             1       /* BOOKE e500 family            */
  23 #define CONFIG_MPC8544          1
  24 #define CONFIG_SOCRATES         1
  25
  26 #define CONFIG_SYS_TEXT_BASE    0xfff80000
  27
  28 #define CONFIG_PCI
  29 #define CONFIG_PCI_INDIRECT_BRIDGE
  30
  31 #define CONFIG_TSEC_ENET                /* tsec ethernet support        */
  32
  33 #define CONFIG_MISC_INIT_R      1       /* Call misc_init_r             */
  34 #define CONFIG_BOARD_EARLY_INIT_R 1     /* Call board_early_init_r      */
  35
  36 #define CONFIG_FSL_LAW          1       /* Use common FSL init code */
  37
  38 /*
  39  * Only possible on E500 Version 2 or newer cores.
  40  */
  41 #define CONFIG_ENABLE_36BIT_PHYS        1
  42
  43 /*
  44  * sysclk for MPC85xx
  45  *
  46  * Two valid values are:
  47  *    33000000
  48  *    66000000
  49  *
  50  * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
  51  * is likely the desired value here, so that is now the default.
  52  * The board, however, can run at 66MHz.  In any event, this value
  53  * must match the settings of some switches.  Details can be found
  54  * in the README.mpc85xxads.
  55  */
  56
  57 #ifndef CONFIG_SYS_CLK_FREQ
  58 #define CONFIG_SYS_CLK_FREQ     66666666
  59 #endif
  60
  61 /*
  62  * These can be toggled for performance analysis, otherwise use default.
  63  */
  64 #define CONFIG_L2_CACHE                 /* toggle L2 cache              */
  65 #define CONFIG_BTB                      /* toggle branch predition      */
  66
  67 #define CONFIG_SYS_INIT_DBCR DBCR_IDM           /* Enable Debug Exceptions      */
  68
  69 #undef  CONFIG_SYS_DRAM_TEST                    /* memory test, takes time      */
  70 #define CONFIG_SYS_MEMTEST_START        0x00400000
  71 #define CONFIG_SYS_MEMTEST_END          0x00C00000
  72
  73 #define CONFIG_SYS_CCSRBAR              0xE0000000
  74 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  75
  76 /* DDR Setup */
  77 #define CONFIG_SYS_FSL_DDR2
  78 #undef CONFIG_FSL_DDR_INTERACTIVE
  79 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
  80 #define CONFIG_DDR_SPD
  81
  82 #undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER        /* DDR controller or DMA? */
  83 #define CONFIG_MEM_INIT_VALUE   0xDeadBeef
  84
  85 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
  86 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  87 #define CONFIG_VERY_BIG_RAM
  88
  89 #define CONFIG_NUM_DDR_CONTROLLERS      1
  90 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  91 #define CONFIG_CHIP_SELECTS_PER_CTRL    2
  92
  93 /* I2C addresses of SPD EEPROMs */
  94 #define SPD_EEPROM_ADDRESS      0x50    /* CTLR 0 DIMM 0 */
  95
  96 #define CONFIG_DDR_DEFAULT_CL   30              /* CAS latency 3        */
  97
  98 /* Hardcoded values, to use instead of SPD */
  99 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000000f
 100 #define CONFIG_SYS_DDR_CS0_CONFIG               0x80010102
 101 #define CONFIG_SYS_DDR_TIMING_0         0x00260802
 102 #define CONFIG_SYS_DDR_TIMING_1         0x3935D322
 103 #define CONFIG_SYS_DDR_TIMING_2         0x14904CC8
 104 #define CONFIG_SYS_DDR_MODE                     0x00480432
 105 #define CONFIG_SYS_DDR_INTERVAL         0x030C0100
 106 #define CONFIG_SYS_DDR_CONFIG_2         0x04400000
 107 #define CONFIG_SYS_DDR_CONFIG                   0xC3008000
 108 #define CONFIG_SYS_DDR_CLK_CONTROL              0x03800000
 109 #define CONFIG_SYS_SDRAM_SIZE                   256 /* in Megs */
 110
 111 /*
 112  * Flash on the LocalBus
 113  */
 114 #define CONFIG_SYS_LBC_CACHE_BASE       0xf0000000      /* Localbus cacheable    */
 115
 116 #define CONFIG_SYS_FLASH0               0xFE000000
 117 #define CONFIG_SYS_FLASH1               0xFC000000
 118 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 }
 119
 120 #define CONFIG_SYS_LBC_FLASH_BASE       CONFIG_SYS_FLASH1       /* Localbus flash start */
 121 #define CONFIG_SYS_FLASH_BASE           CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH     */
 122
 123 #define CONFIG_SYS_BR0_PRELIM           0xfe001001      /* port size 16bit      */
 124 #define CONFIG_SYS_OR0_PRELIM           0xfe000030      /* 32MB Flash           */
 125 #define CONFIG_SYS_BR1_PRELIM           0xfc001001      /* port size 16bit      */
 126 #define CONFIG_SYS_OR1_PRELIM           0xfe000030      /* 32MB Flash           */
 127
 128 #define CONFIG_SYS_FLASH_CFI                            /* flash is CFI compat. */
 129 #define CONFIG_FLASH_CFI_DRIVER                 /* Use common CFI driver*/
 130
 131 #define CONFIG_SYS_MAX_FLASH_BANKS      2               /* number of banks      */
 132 #define CONFIG_SYS_MAX_FLASH_SECT       256             /* sectors per device   */
 133 #undef  CONFIG_SYS_FLASH_CHECKSUM
 134 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms)     */
 135 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms)     */
 136
 137 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor     */
 138
 139 #define CONFIG_SYS_LBC_LCRR             0x00030004    /* LB clock ratio reg     */
 140 #define CONFIG_SYS_LBC_LBCR             0x00000000    /* LB config reg          */
 141 #define CONFIG_SYS_LBC_LSRT             0x20000000    /* LB sdram refresh timer */
 142 #define CONFIG_SYS_LBC_MRTPR            0x20000000    /* LB refresh timer presc.*/
 143
 144 #define CONFIG_SYS_INIT_RAM_LOCK        1
 145 #define CONFIG_SYS_INIT_RAM_ADDR        0xe4010000      /* Initial RAM address  */
 146 #define CONFIG_SYS_INIT_RAM_SIZE        0x4000          /* Size used area in RAM*/
 147
 148 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 149 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 150
 151 #define CONFIG_SYS_MONITOR_LEN          (384 * 1024)    /* Reserve 384KiB for Mon */
 152 #define CONFIG_SYS_MALLOC_LEN           (4 << 20)       /* Reserve 4 MB for malloc */
 153
 154 /* FPGA and NAND */
 155 #define CONFIG_SYS_FPGA_BASE            0xc0000000
 156 #define CONFIG_SYS_FPGA_SIZE            0x00100000      /* 1 MB         */
 157 #define CONFIG_SYS_HMI_BASE             0xc0010000
 158 #define CONFIG_SYS_BR3_PRELIM           0xc0001881      /* UPMA, 32-bit */
 159 #define CONFIG_SYS_OR3_PRELIM           0xfff00000      /* 1 MB         */
 160
 161 #define CONFIG_SYS_NAND_BASE            (CONFIG_SYS_FPGA_BASE + 0x70)
 162 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 163 #define CONFIG_CMD_NAND
 164
 165 /* LIME GDC */
 166 #define CONFIG_SYS_LIME_BASE            0xc8000000
 167 #define CONFIG_SYS_LIME_SIZE            0x04000000      /* 64 MB        */
 168 #define CONFIG_SYS_BR2_PRELIM           0xc80018a1      /* UPMB, 32-bit */
 169 #define CONFIG_SYS_OR2_PRELIM           0xfc000000      /* 64 MB        */
 170
 171 #define CONFIG_VIDEO_MB862xx
 172 #define CONFIG_VIDEO_MB862xx_ACCEL
 173 #define CONFIG_VIDEO_LOGO
 174 #define CONFIG_VIDEO_BMP_LOGO
 175 #define CONFIG_CONSOLE_EXTRA_INFO
 176 #define VIDEO_FB_16BPP_PIXEL_SWAP
 177 #define VIDEO_FB_16BPP_WORD_SWAP
 178 #define CONFIG_VIDEO_SW_CURSOR
 179 #define CONFIG_SPLASH_SCREEN
 180 #define CONFIG_VIDEO_BMP_GZIP
 181 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE  (2 << 20)       /* decompressed img */
 182
 183 /* SDRAM Clock frequency, 100MHz (0x0000) or 133MHz (0x10000) */
 184 #define CONFIG_SYS_MB862xx_CCF          0x10000
 185 /* SDRAM parameter */
 186 #define CONFIG_SYS_MB862xx_MMR          0x4157BA63
 187
 188 /* Serial Port */
 189
 190 #define CONFIG_CONS_INDEX     1
 191 #define CONFIG_SYS_NS16550_SERIAL
 192 #define CONFIG_SYS_NS16550_REG_SIZE     1
 193 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 194
 195 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 196 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 197
 198 #define CONFIG_BAUDRATE         115200
 199
 200 #define CONFIG_SYS_BAUDRATE_TABLE  \
 201         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 202
 203 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 204 #define CONFIG_AUTO_COMPLETE    1       /* add autocompletion support */
 205
 206 /*
 207  * I2C
 208  */
 209 #define CONFIG_SYS_I2C
 210 #define CONFIG_SYS_I2C_FSL
 211 #define CONFIG_SYS_FSL_I2C_SPEED        102124
 212 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 213 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 214 #define CONFIG_SYS_FSL_I2C2_SPEED       102124
 215 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 216 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 217
 218 /* I2C RTC */
 219 #define CONFIG_RTC_RX8025               /* Use Epson rx8025 rtc via i2c */
 220 #define CONFIG_SYS_I2C_RTC_ADDR 0x32    /* at address 0x32              */
 221
 222 /* I2C W83782G HW-Monitoring IC */
 223 #define CONFIG_SYS_I2C_W83782G_ADDR     0x28    /* W83782G address              */
 224
 225 /* I2C temp sensor */
 226 /* Socrates uses Maxim's        DS75, which is compatible with LM75 */
 227 #define CONFIG_DTT_LM75         1
 228 #define CONFIG_DTT_SENSORS      {4}             /* Sensor addresses     */
 229 #define CONFIG_SYS_DTT_MAX_TEMP 125
 230 #define CONFIG_SYS_DTT_LOW_TEMP -55
 231 #define CONFIG_SYS_DTT_HYSTERESIS       3
 232 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       4
 233
 234 /*
 235  * General PCI
 236  * Memory space is mapped 1-1.
 237  */
 238 #define CONFIG_SYS_PCI_PHYS             0x80000000      /* 1G PCI TLB */
 239
 240 /* PCI is clocked by the external source at 33 MHz */
 241 #define CONFIG_PCI_CLK_FREQ     33000000
 242 #define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
 243 #define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
 244 #define CONFIG_SYS_PCI1_MEM_SIZE        0x20000000      /* 512M                 */
 245 #define CONFIG_SYS_PCI1_IO_BASE 0xE2000000
 246 #define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
 247 #define CONFIG_SYS_PCI1_IO_SIZE 0x01000000      /* 16M                  */
 248
 249 #if defined(CONFIG_PCI)
 250 #define CONFIG_PCI_PNP                  /* do pci plug-and-play         */
 251 #undef CONFIG_PCI_SCAN_SHOW             /* show pci devices on startup  */
 252 #endif  /* CONFIG_PCI */
 253
 254 #define CONFIG_MII              1       /* MII PHY management */
 255 #define CONFIG_TSEC1    1
 256 #define CONFIG_TSEC1_NAME       "TSEC0"
 257 #define CONFIG_TSEC3    1
 258 #define CONFIG_TSEC3_NAME       "TSEC1"
 259 #undef CONFIG_MPC85XX_FEC
 260
 261 #define TSEC1_PHY_ADDR          0
 262 #define TSEC3_PHY_ADDR          1
 263
 264 #define TSEC1_PHYIDX            0
 265 #define TSEC3_PHYIDX            0
 266 #define TSEC1_FLAGS             TSEC_GIGABIT
 267 #define TSEC3_FLAGS             TSEC_GIGABIT
 268
 269 /* Options are: TSEC[0,1] */
 270 #define CONFIG_ETHPRIME         "TSEC0"
 271 #define CONFIG_PHY_GIGE         1       /* Include GbE speed/duplex detection */
 272
 273 #define CONFIG_HAS_ETH0
 274 #define CONFIG_HAS_ETH1
 275
 276 /*
 277  * Environment
 278  */
 279 #define CONFIG_ENV_IS_IN_FLASH  1
 280 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env     */
 281 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 282 #define CONFIG_ENV_SIZE         0x4000
 283 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
 284 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 285
 286 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
 287 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change        */
 288
 289 #define CONFIG_TIMESTAMP                /* Print image info with ts     */
 290
 291 /*
 292  * BOOTP options
 293  */
 294 #define CONFIG_BOOTP_BOOTFILESIZE
 295 #define CONFIG_BOOTP_BOOTPATH
 296 #define CONFIG_BOOTP_GATEWAY
 297 #define CONFIG_BOOTP_HOSTNAME
 298
 299 /*
 300  * Command line configuration.
 301  */
 302 #define CONFIG_CMD_BMP
 303 #define CONFIG_CMD_DATE
 304 #define CONFIG_CMD_DTT
 305 #undef CONFIG_CMD_EEPROM
 306 #define CONFIG_CMD_SDRAM
 307 #define CONFIG_CMD_REGINFO
 308
 309 #if defined(CONFIG_PCI)
 310     #define CONFIG_CMD_PCI
 311 #endif
 312
 313 #undef CONFIG_WATCHDOG                  /* watchdog disabled            */
 314
 315 /*
 316  * Miscellaneous configurable options
 317  */
 318 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 319 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address         */
 320
 321 #if defined(CONFIG_CMD_KGDB)
 322     #define CONFIG_SYS_CBSIZE   1024            /* Console I/O Buffer Size      */
 323 #else
 324     #define CONFIG_SYS_CBSIZE   256             /* Console I/O Buffer Size      */
 325 #endif
 326
 327 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buf Size    */
 328 #define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
 329 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 330
 331 /*
 332  * For booting Linux, the board info and command line data
 333  * have to be in the first 8 MB of memory, since this is
 334  * the maximum mapped by the Linux kernel during initialization.
 335  */
 336 #define CONFIG_SYS_BOOTMAPSZ    (8 << 20)       /* Initial Memory map for Linux */
 337
 338 #if defined(CONFIG_CMD_KGDB)
 339 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port*/
 340 #endif
 341
 342 #define CONFIG_LOADADDR  200000         /* default addr for tftp & bootm*/
 343
 344
 345 #define CONFIG_PREBOOT  "echo;" \
 346         "echo Welcome on the ABB Socrates Board;" \
 347         "echo"
 348
 349 #undef  CONFIG_BOOTARGS         /* the boot command will set bootargs   */
 350
 351 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 352         "netdev=eth0\0"                                                 \
 353         "consdev=ttyS0\0"                                               \
 354         "uboot_file=/home/tftp/syscon3/u-boot.bin\0"                    \
 355         "bootfile=/home/tftp/syscon3/uImage\0"                          \
 356         "fdt_file=/home/tftp/syscon3/socrates.dtb\0"                    \
 357         "initrd_file=/home/tftp/syscon3/uinitrd.gz\0"                   \
 358         "uboot_addr=FFFA0000\0"                                         \
 359         "kernel_addr=FE000000\0"                                        \
 360         "fdt_addr=FE1E0000\0"                                           \
 361         "ramdisk_addr=FE200000\0"                                       \
 362         "fdt_addr_r=B00000\0"                                           \
 363         "kernel_addr_r=200000\0"                                        \
 364         "ramdisk_addr_r=400000\0"                                       \
 365         "rootpath=/opt/eldk/ppc_85xxDP\0"                               \
 366         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 367         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 368                 "nfsroot=$serverip:$rootpath\0"                         \
 369         "addcons=setenv bootargs $bootargs "                            \
 370                 "console=$consdev,$baudrate\0"                          \
 371         "addip=setenv bootargs $bootargs "                              \
 372                 "ip=$ipaddr:$serverip:$gatewayip:$netmask"              \
 373                 ":$hostname:$netdev:off panic=1\0"                      \
 374         "boot_nor=run ramargs addcons;"                                 \
 375                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
 376         "net_nfs=tftp ${kernel_addr_r} ${bootfile}; "                   \
 377                 "tftp ${fdt_addr_r} ${fdt_file}; "                      \
 378                 "run nfsargs addip addcons;"                            \
 379                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
 380         "update_uboot=tftp 100000 ${uboot_file};"                       \
 381                 "protect off fffa0000 ffffffff;"                        \
 382                 "era fffa0000 ffffffff;"                                \
 383                 "cp.b 100000 fffa0000 ${filesize};"                     \
 384                 "setenv filesize;saveenv\0"                             \
 385         "update_kernel=tftp 100000 ${bootfile};"                        \
 386                 "era fe000000 fe1dffff;"                                \
 387                 "cp.b 100000 fe000000 ${filesize};"                     \
 388                 "setenv filesize;saveenv\0"                             \
 389         "update_fdt=tftp 100000 ${fdt_file};"                           \
 390                 "era fe1e0000 fe1fffff;"                                \
 391                 "cp.b 100000 fe1e0000 ${filesize};"                     \
 392                 "setenv filesize;saveenv\0"                             \
 393         "update_initrd=tftp 100000 ${initrd_file};"                     \
 394                 "era fe200000 fe9fffff;"                                \
 395                 "cp.b 100000 fe200000 ${filesize};"                     \
 396                 "setenv filesize;saveenv\0"                             \
 397         "clean_data=era fea00000 fff5ffff\0"                            \
 398         "usbargs=setenv bootargs root=/dev/sda1 rw\0"                   \
 399         "load_usb=usb start;"                                           \
 400                 "ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0"      \
 401         "boot_usb=run load_usb usbargs addcons;"                        \
 402                 "bootm ${kernel_addr_r} - ${fdt_addr};"                 \
 403                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
 404         ""
 405 #define CONFIG_BOOTCOMMAND      "run boot_nor"
 406
 407 /* pass open firmware flat tree */
 408
 409 /* USB support */
 410 #define CONFIG_USB_OHCI_NEW             1
 411 #define CONFIG_PCI_OHCI                 1
 412 #define CONFIG_PCI_OHCI_DEVNO           3 /* Number in PCI list */
 413 #define CONFIG_PCI_EHCI_DEVNO           (CONFIG_PCI_OHCI_DEVNO / 2)
 414 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS      15
 415 #define CONFIG_SYS_USB_OHCI_SLOT_NAME           "ohci_pci"
 416 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
 417 #define CONFIG_DOS_PARTITION            1
 418
 419 #endif  /* __CONFIG_H */