1 /* SPDX-License-Identifier: GPL-2.0+ */
4 * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com.
6 * Wolfgang Denk <wd@denx.de>
7 * Copyright 2004 Freescale Semiconductor.
8 * (C) Copyright 2002,2003 Motorola,Inc.
9 * Xianghua Xiao <X.Xiao@motorola.com>
19 /* High Level Configuration Options */
20 #define CONFIG_SOCRATES 1
23 * Only possible on E500 Version 2 or newer cores.
25 #define CONFIG_ENABLE_36BIT_PHYS 1
30 * Two valid values are:
34 * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
35 * is likely the desired value here, so that is now the default.
36 * The board, however, can run at 66MHz. In any event, this value
37 * must match the settings of some switches. Details can be found
38 * in the README.mpc85xxads.
41 #ifndef CONFIG_SYS_CLK_FREQ
42 #define CONFIG_SYS_CLK_FREQ 66666666
46 * These can be toggled for performance analysis, otherwise use default.
48 #define CONFIG_L2_CACHE /* toggle L2 cache */
49 #define CONFIG_BTB /* toggle branch predition */
51 #define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
53 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
55 #define CONFIG_SYS_CCSRBAR 0xE0000000
56 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
59 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
60 #define CONFIG_DDR_SPD
62 #undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
63 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef
65 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
66 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
67 #define CONFIG_VERY_BIG_RAM
69 #define CONFIG_DIMM_SLOTS_PER_CTLR 1
70 #define CONFIG_CHIP_SELECTS_PER_CTRL 2
72 /* I2C addresses of SPD EEPROMs */
73 #define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */
75 #define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */
77 /* Hardcoded values, to use instead of SPD */
78 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
79 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102
80 #define CONFIG_SYS_DDR_TIMING_0 0x00260802
81 #define CONFIG_SYS_DDR_TIMING_1 0x3935D322
82 #define CONFIG_SYS_DDR_TIMING_2 0x14904CC8
83 #define CONFIG_SYS_DDR_MODE 0x00480432
84 #define CONFIG_SYS_DDR_INTERVAL 0x030C0100
85 #define CONFIG_SYS_DDR_CONFIG_2 0x04400000
86 #define CONFIG_SYS_DDR_CONFIG 0xC3008000
87 #define CONFIG_SYS_DDR_CLK_CONTROL 0x03800000
88 #define CONFIG_SYS_SDRAM_SIZE 256 /* in Megs */
91 * Flash on the LocalBus
93 #define CONFIG_SYS_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */
95 #define CONFIG_SYS_FLASH_QUIET_TEST
96 #define CONFIG_SYS_FLASH0 0xFE000000
97 #define CONFIG_SYS_FLASH1 0xFC000000
98 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 }
100 #define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */
101 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */
103 #define CONFIG_SYS_BR0_PRELIM 0xfe001001 /* port size 16bit */
104 #define CONFIG_SYS_OR0_PRELIM 0xfe000030 /* 32MB Flash */
105 #define CONFIG_SYS_BR1_PRELIM 0xfc001001 /* port size 16bit */
106 #define CONFIG_SYS_OR1_PRELIM 0xfe000030 /* 32MB Flash */
108 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
109 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */
110 #undef CONFIG_SYS_FLASH_CHECKSUM
111 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
112 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
114 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
116 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
117 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
118 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
119 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/
121 #define CONFIG_SYS_INIT_RAM_LOCK 1
122 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
123 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM*/
125 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
126 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
128 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384KiB for Mon */
129 #define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4 MB for malloc */
132 #define CONFIG_SYS_FPGA_BASE 0xc0000000
133 #define CONFIG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */
134 #define CONFIG_SYS_HMI_BASE 0xc0010000
135 #define CONFIG_SYS_BR3_PRELIM 0xc0001881 /* UPMA, 32-bit */
136 #define CONFIG_SYS_OR3_PRELIM 0xfff00000 /* 1 MB */
138 #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_FPGA_BASE + 0x70)
139 #define CONFIG_SYS_MAX_NAND_DEVICE 1
142 #define CONFIG_SYS_LIME_BASE 0xc8000000
143 #define CONFIG_SYS_LIME_SIZE 0x04000000 /* 64 MB */
144 #define CONFIG_SYS_BR2_PRELIM 0xc80018a1 /* UPMB, 32-bit */
145 #define CONFIG_SYS_OR2_PRELIM 0xfc000000 /* 64 MB */
147 #define CONFIG_SYS_SPD_BUS_NUM 0
149 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
153 * Memory space is mapped 1-1.
156 /* PCI is clocked by the external source at 33 MHz */
157 #define CONFIG_PCI_CLK_FREQ 33000000
158 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
159 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
160 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
161 #define CONFIG_SYS_PCI1_IO_BASE 0xE2000000
162 #define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
163 #define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */
165 #define CONFIG_TSEC1 1
166 #define CONFIG_TSEC1_NAME "TSEC0"
167 #define CONFIG_TSEC3 1
168 #define CONFIG_TSEC3_NAME "TSEC1"
169 #undef CONFIG_MPC85XX_FEC
171 #define TSEC1_PHY_ADDR 0
172 #define TSEC3_PHY_ADDR 1
174 #define TSEC1_PHYIDX 0
175 #define TSEC3_PHYIDX 0
176 #define TSEC1_FLAGS TSEC_GIGABIT
177 #define TSEC3_FLAGS TSEC_GIGABIT
179 /* Options are: TSEC[0,1] */
180 #define CONFIG_ETHPRIME "TSEC0"
182 #define CONFIG_HAS_ETH0
183 #define CONFIG_HAS_ETH1
189 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
190 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
192 #define CONFIG_TIMESTAMP /* Print image info with ts */
197 #define CONFIG_BOOTP_BOOTFILESIZE
199 #undef CONFIG_WATCHDOG /* watchdog disabled */
202 * Miscellaneous configurable options
204 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
207 * For booting Linux, the board info and command line data
208 * have to be in the first 8 MB of memory, since this is
209 * the maximum mapped by the Linux kernel during initialization.
211 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
213 #if defined(CONFIG_CMD_KGDB)
214 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/
217 #define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/
219 #define CONFIG_EXTRA_ENV_SETTINGS \
222 "uboot_file=/home/tftp/syscon3/u-boot.bin\0" \
223 "bootfile=/home/tftp/syscon3/uImage\0" \
224 "fdt_file=/home/tftp/syscon3/socrates.dtb\0" \
225 "initrd_file=/home/tftp/syscon3/uinitrd.gz\0" \
226 "uboot_addr=FFF60000\0" \
227 "kernel_addr=FE000000\0" \
228 "fdt_addr=FE1E0000\0" \
229 "ramdisk_addr=FE200000\0" \
230 "fdt_addr_r=B00000\0" \
231 "kernel_addr_r=200000\0" \
232 "ramdisk_addr_r=400000\0" \
233 "rootpath=/opt/eldk/ppc_85xxDP\0" \
234 "ramargs=setenv bootargs root=/dev/ram rw\0" \
235 "nfsargs=setenv bootargs root=/dev/nfs rw " \
236 "nfsroot=$serverip:$rootpath\0" \
237 "addcons=setenv bootargs $bootargs " \
238 "console=$consdev,$baudrate\0" \
239 "addip=setenv bootargs $bootargs " \
240 "ip=$ipaddr:$serverip:$gatewayip:$netmask" \
241 ":$hostname:$netdev:off panic=1\0" \
242 "boot_nor=run ramargs addcons;" \
243 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
244 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
245 "tftp ${fdt_addr_r} ${fdt_file}; " \
246 "run nfsargs addip addcons;" \
247 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
248 "update_uboot=tftp 100000 ${uboot_file};" \
249 "protect off fff60000 ffffffff;" \
250 "era fff60000 ffffffff;" \
251 "cp.b 100000 fff60000 ${filesize};" \
252 "setenv filesize;saveenv\0" \
253 "update_kernel=tftp 100000 ${bootfile};" \
254 "era fe000000 fe1dffff;" \
255 "cp.b 100000 fe000000 ${filesize};" \
256 "setenv filesize;saveenv\0" \
257 "update_fdt=tftp 100000 ${fdt_file};" \
258 "era fe1e0000 fe1fffff;" \
259 "cp.b 100000 fe1e0000 ${filesize};" \
260 "setenv filesize;saveenv\0" \
261 "update_initrd=tftp 100000 ${initrd_file};" \
262 "era fe200000 fe9fffff;" \
263 "cp.b 100000 fe200000 ${filesize};" \
264 "setenv filesize;saveenv\0" \
265 "clean_data=era fea00000 fff5ffff\0" \
266 "usbargs=setenv bootargs root=/dev/sda1 rw\0" \
267 "load_usb=usb start;" \
268 "ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0" \
269 "boot_usb=run load_usb usbargs addcons;" \
270 "bootm ${kernel_addr_r} - ${fdt_addr};" \
271 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
273 #define CONFIG_BOOTCOMMAND "run boot_nor"
275 /* pass open firmware flat tree */
278 #define CONFIG_USB_OHCI_NEW 1
279 #define CONFIG_PCI_OHCI 1
280 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
281 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
282 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
284 #endif /* __CONFIG_H */