include/configs/socfpga_arria5_secu1.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) 2017-2020 ABB
   4  *
   5  */
   6 #ifndef __CONFIG_SOCFPGA_SECU1_H__
   7 #define __CONFIG_SOCFPGA_SECU1_H__
   8
   9 #include <asm/arch/base_addr_ac5.h>
  10
  11 /* Call misc_init_r */
  12 #define CONFIG_MISC_INIT_R
  13
  14 #define CONFIG_HUSH_INIT_VAR
  15 /* Eternal oscillator */
  16 #define CONFIG_SYS_TIMER_RATE   40000000
  17
  18 /* Memory configurations */
  19 #define PHYS_SDRAM_1_SIZE       0x20000000      /* 512MiB on SECU1 */
  20
  21 /*
  22  * We use bootcounter in i2c nvram of the RTC (0x68)
  23  * The offset fopr the bootcounter is 0x9e, which are
  24  * the last two bytes of the 128 bytes large NVRAM in the
  25  * RTC which begin at address 0x20
  26  */
  27 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
  28
  29 /* Booting Linux */
  30 #define CONFIG_BOOTDELAY        2
  31 #define CONFIG_BOOTFILE         "zImage"
  32 #define CONFIG_BOOTARGS         \
  33         "console=ttyS0," __stringify(CONFIG_BAUDRATE) \
  34         " ubi.fm_autoconvert=1" \
  35         " uio_pdrv_genirq.of_id=\"idq,regbank\""
  36
  37 #define CONFIG_BOOTCOMMAND      \
  38         "setenv bootcmd '"      \
  39                 "bridge enable; "       \
  40                 "if test ${bootnum} = \"b\"; " \
  41                       "then run _fpga_loadsafe; " \
  42                 "else if test ${bootcount} -eq 4; then echo \"Switching copy...\"; setexpr x $bootnum % 2 && setexpr bootnum $x + 1; saveenv; fi; " \
  43                       "run _fpga_loaduser; " \
  44                 "fi;" \
  45                 "echo \"Booting bank $bootnum\" && run userload && run userboot;" \
  46         "' && " \
  47         "setenv altbootcmd 'setenv bootnum b && saveenv && boot;' && " \
  48         "saveenv && saveenv && boot;"
  49
  50 #define CONFIG_CMDLINE_TAG
  51 #define CONFIG_SYS_BOOTM_LEN            (64 << 20)
  52
  53 /* Environment settings */
  54 #define CONFIG_ENV_OVERWRITE
  55
  56 /*
  57  * Autoboot
  58  *
  59  * After 45s of inactivity in the prompt, the board will reset.
  60  * Set 'bootretry' in the environment to -1 to disable this behavior
  61  */
  62 #define CONFIG_BOOT_RETRY_TIME 45
  63 #define CONFIG_RESET_TO_RETRY
  64
  65 #define CONFIG_LOADADDR         0x01000000
  66 #define CONFIG_SYS_LOAD_ADDR   CONFIG_KM_KERNEL_ADDR
  67
  68 /*
  69  * FPGA Remote Update related environment
  70  *
  71  * Note that since those commands access the FPGA, the HPS-to-FPGA
  72  * bridges MUST have been previously enabled (for example
  73  * with 'bridge enable').
  74  */
  75 #define FPGA_RMTU_ENV \
  76         "rmtu_page=0xFF29000C\0" \
  77         "rmtu_reconfig=0xFF290018\0" \
  78         "fpga_safebase=0x0\0" \
  79         "fpga_userbase=0x2000000\0" \
  80         "_fpga_loaduser=echo Loading FPGA USER image..." \
  81                 " && mw ${rmtu_page} ${fpga_userbase} && mw ${rmtu_reconfig} 1\0" \
  82         "_fpga_loadsafe=echo Loading FPGA SAFE image..." \
  83                 " && mw ${rmtu_page} ${fpga_safebase} && mw ${rmtu_reconfig} 1\0" \
  84
  85 #define CONFIG_KM_NEW_ENV \
  86         "newenv=" \
  87                 "nand erase 0x100000 0x40000\0"
  88
  89 #define CONFIG_KM_DEF_ENV_BOOTTARGETS \
  90         "release=" \
  91                 "run newenv; reset\0" \
  92         "develop=" \
  93                 "tftp 0x200000 scripts/develop-secu.txt && env import -t 0x200000 ${filesize} && saveenv && reset\0"
  94
  95 #define CONFIG_EXTRA_ENV_SETTINGS \
  96         FPGA_RMTU_ENV \
  97         CONFIG_KM_DEF_ENV_BOOTTARGETS \
  98         CONFIG_KM_NEW_ENV \
  99         "socfpga_legacy_reset_compat=1\0"       \
 100         "altbootcmd=run bootcmd;\0"     \
 101         "bootlimit=6\0" \
 102         "bootnum=1\0" \
 103         "bootretry=" __stringify(CONFIG_BOOT_RETRY_TIME) "\0" \
 104         "fdt_addr=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \
 105         "load=tftpboot ${loadaddr} u-boot-with-nand-spl.sfp\0" \
 106         "loadaddr=" __stringify(CONFIG_KM_KERNEL_ADDR) "\0" \
 107         "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
 108         "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
 109         "update=nand erase 0x0 0x00100000 && nand write ${loadaddr} 0x0 ${filesize}\0" \
 110         "userload=ubi part nand.ubi &&" \
 111                 "ubi check rootfs$bootnum &&" \
 112                 "ubi read $fdt_addr dtb$bootnum &&" \
 113                 "ubi read $loadaddr kernel$bootnum\0" \
 114         "userboot=setenv bootargs " CONFIG_BOOTARGS \
 115                 " ubi.mtd=1 ubi.block=0,rootfs$bootnum root=/dev/ubiblock0_$ubivolid"   \
 116                 " ro rootfstype=squashfs init=sbin/preinit;" \
 117                 "bootz ${loadaddr} - ${fdt_addr}\0" \
 118         "verify=y\0"
 119
 120 /* The rest of the configuration is shared */
 121 #include <configs/socfpga_common.h>
 122
 123 #ifdef CONFIG_SPL_NAND_SUPPORT
 124 #undef CONFIG_SYS_NAND_U_BOOT_OFFS
 125 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 126 #endif
 127
 128 #undef CONFIG_WATCHDOG_TIMEOUT_MSECS
 129 #define CONFIG_WATCHDOG_TIMEOUT_MSECS   60000
 130
 131 #endif  /* __CONFIG_SOCFPGA_SECU1_H__ */