include/configs/socfpga_arria5_secu1.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) 2017-2020 ABB
   4  *
   5  */
   6 #ifndef __CONFIG_SOCFPGA_SECU1_H__
   7 #define __CONFIG_SOCFPGA_SECU1_H__
   8
   9 #include <asm/arch/base_addr_ac5.h>
  10 #include <linux/stringify.h>
  11
  12 /* Call misc_init_r */
  13 #define CONFIG_MISC_INIT_R
  14
  15 #define CONFIG_HUSH_INIT_VAR
  16 /* Eternal oscillator */
  17 #define CONFIG_SYS_TIMER_RATE   40000000
  18
  19 /* Memory configurations */
  20 #define PHYS_SDRAM_1_SIZE       0x20000000      /* 512MiB on SECU1 */
  21
  22 /*
  23  * We use bootcounter in i2c nvram of the RTC (0x68)
  24  * The offset fopr the bootcounter is 0x9e, which are
  25  * the last two bytes of the 128 bytes large NVRAM in the
  26  * RTC which begin at address 0x20
  27  */
  28 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
  29
  30 /* Booting Linux */
  31 #define CONFIG_BOOTFILE         "zImage"
  32
  33 #define CONFIG_BOOTCOMMAND      \
  34         "setenv bootcmd '"      \
  35                 "bridge enable; "       \
  36                 "if test ${bootnum} = \"b\"; " \
  37                       "then run _fpga_loadsafe; " \
  38                 "else if test ${bootcount} -eq 4; then echo \"Switching copy...\"; setexpr x $bootnum % 2 && setexpr bootnum $x + 1; saveenv; fi; " \
  39                       "run _fpga_loaduser; " \
  40                 "fi;" \
  41                 "echo \"Booting bank $bootnum\" && run userload && run userboot;" \
  42         "' && " \
  43         "setenv altbootcmd 'setenv bootnum b && saveenv && boot;' && " \
  44         "saveenv && saveenv && boot;"
  45
  46 #define CONFIG_CMDLINE_TAG
  47 #define CONFIG_SYS_BOOTM_LEN            (64 << 20)
  48
  49 /* Environment settings */
  50
  51 /*
  52  * Autoboot
  53  *
  54  * After 45s of inactivity in the prompt, the board will reset.
  55  * Set 'bootretry' in the environment to -1 to disable this behavior
  56  */
  57 #define CONFIG_BOOT_RETRY_TIME 45
  58 #define CONFIG_RESET_TO_RETRY
  59
  60 #define CONFIG_LOADADDR         0x01000000
  61 #define CONFIG_SYS_LOAD_ADDR   CONFIG_KM_KERNEL_ADDR
  62
  63 /*
  64  * FPGA Remote Update related environment
  65  *
  66  * Note that since those commands access the FPGA, the HPS-to-FPGA
  67  * bridges MUST have been previously enabled (for example
  68  * with 'bridge enable').
  69  */
  70 #define FPGA_RMTU_ENV \
  71         "rmtu_page=0xFF29000C\0" \
  72         "rmtu_reconfig=0xFF290018\0" \
  73         "fpga_safebase=0x0\0" \
  74         "fpga_userbase=0x2000000\0" \
  75         "_fpga_loaduser=echo Loading FPGA USER image..." \
  76                 " && mw ${rmtu_page} ${fpga_userbase} && mw ${rmtu_reconfig} 1\0" \
  77         "_fpga_loadsafe=echo Loading FPGA SAFE image..." \
  78                 " && mw ${rmtu_page} ${fpga_safebase} && mw ${rmtu_reconfig} 1\0" \
  79
  80 #define CONFIG_KM_NEW_ENV \
  81         "newenv=" \
  82                 "nand erase 0x100000 0x40000\0"
  83
  84 #define CONFIG_KM_DEF_ENV_BOOTTARGETS \
  85         "release=" \
  86                 "run newenv; reset\0" \
  87         "develop=" \
  88                 "tftp 0x200000 scripts/develop-secu.txt && env import -t 0x200000 ${filesize} && saveenv && reset\0"
  89
  90 #define CONFIG_EXTRA_ENV_SETTINGS \
  91         FPGA_RMTU_ENV \
  92         CONFIG_KM_DEF_ENV_BOOTTARGETS \
  93         CONFIG_KM_NEW_ENV \
  94         "socfpga_legacy_reset_compat=1\0"       \
  95         "altbootcmd=run bootcmd;\0"     \
  96         "bootlimit=6\0" \
  97         "bootnum=1\0" \
  98         "bootretry=" __stringify(CONFIG_BOOT_RETRY_TIME) "\0" \
  99         "fdt_addr=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \
 100         "load=tftpboot ${loadaddr} u-boot-with-nand-spl.sfp\0" \
 101         "loadaddr=" __stringify(CONFIG_KM_KERNEL_ADDR) "\0" \
 102         "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
 103         "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
 104         "update=nand erase 0x0 0x00100000 && nand write ${loadaddr} 0x0 ${filesize}\0" \
 105         "userload=ubi part nand.ubi &&" \
 106                 "ubi check rootfs$bootnum &&" \
 107                 "ubi read $fdt_addr dtb$bootnum &&" \
 108                 "ubi read $loadaddr kernel$bootnum\0" \
 109         "userboot=setenv bootargs " CONFIG_BOOTARGS \
 110                 " ubi.mtd=1 ubi.block=0,rootfs$bootnum root=/dev/ubiblock0_$ubivolid"   \
 111                 " ro rootfstype=squashfs init=sbin/preinit;" \
 112                 "bootz ${loadaddr} - ${fdt_addr}\0" \
 113         "verify=y\0"
 114
 115 /* The rest of the configuration is shared */
 116 #include <configs/socfpga_common.h>
 117
 118 #ifdef CONFIG_SPL_NAND_SUPPORT
 119 #undef CONFIG_SYS_NAND_U_BOOT_OFFS
 120 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 121 #endif
 122
 123 #undef CONFIG_WATCHDOG_TIMEOUT_MSECS
 124 #define CONFIG_WATCHDOG_TIMEOUT_MSECS   60000
 125
 126 #endif  /* __CONFIG_SOCFPGA_SECU1_H__ */