3 * Heiko Schocher, DENX Software Engineering, <hs@denx.de>.
7 * Juergen Beisert, EuroDesign embedded technologies, jbeisert@eurodsn.de
9 * See file CREDITS for list of people who contributed to this
12 * This program is free software; you can redistribute it and/or
13 * modify it under the terms of the GNU General Public License as
14 * published by the Free Software Foundation; either version 2 of
15 * the License, or (at your option) any later version.
17 * This program is distributed in the hope that it will be useful,
18 * but WITHOUT ANY WARRANTY; without even the implied warranty of
19 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
20 * GNU General Public License for more details.
22 * You should have received a copy of the GNU General Public License
23 * along with this program; if not, write to the Free Software
24 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
31 #undef USE_VGA_GRAPHICS
34 * 0x00000000 .... 0x03FFFFFF -> RAM (up to 128MiB)
35 * 0x74000000 .... 0x740FFFFF -> CS#6
36 * 0x74100000 .... 0x741FFFFF -> CS#7
37 * 0x74200000 .... 0x742FFFFF -> CS4# if no internal USB
38 * 0x74300000 .... 0x743FFFFF -> CS5# if no boosted IDE
39 * 0x77C00000 .... 0x77CFFFFF -> CS4# USB HC (1 MiB)
40 * 0x77D00000 .... 0x77DFFFFF -> CS1# NAND-Flash (1 MiB)
41 * 0x78000000 .... 0x78FFFFFF -> CS2# ISA-Bus Speicherzugriff (16 MiB)
42 * 0x79000000 .... 0x7900FFFF -> CS2# ISA-Bus IO-Zugriff (16 MiB, mapped: 64kiB)
43 * 0x79010000 .... 0x79FFFFFF -> CS2# ISA-Bus IO-Zugriff (mirrored)
44 * 0x7A000000 .... 0x7A0FFFFF -> CS5# IDE emulation (1MiB)
46 * 0x80000000 .... 0x9FFFFFFF -> PCI-Bus Speicherzugriff (512MiB, mapped: 1:1)
47 * 0xA0000000 .... 0xBFFFFFFF -> PCI-Bus Speicherzugriff (512MiB, mapped: 0x00000000...0x1FFFFFFF)
48 * 0xE8000000 .... 0xE800FFFF -> PCI-Bus IO-Zugriff (64kiB, translated to PCI: 0x0000...0xFFFF)
49 * 0xE8800000 .... 0xEBFFFFFF -> PCI-Bus IO-Zugriff (56MiB, translated to PCI: 0x00800000...0x3FFFFFF)
50 * 0xEED00000 .... 0xEED00003 -> PCI-Bus
51 * 0xEF400000 .... 0xEF40003F -> PCI-Bus Local Configuration Registers
52 * 0xEF40003F .... 0xEF5FFFFF -> reserved
53 * 0xEF600000 .... 0xEFFFFFFF -> 405GP internal Devices (10 MiB)
54 * 0xF0000000 .... 0xF01FFFFF -> Flash-ROM (2 MiB)
55 * 0xF0200000 .... 0xF7FFFFFF -> free for flash devices
56 * 0xF8000000 .... 0xF8000FFF -> OnChipMemory (4kiB)
57 * 0xF8001000 .... 0xFFDFFFFF -> free for flash devices
58 * 0xFFE00000 .... 0xFFFFFFFF -> BOOT-ROM (2 MiB)
63 #define CONFIG_405GP 1
65 #define CONFIG_BOARD_EARLY_INIT_F 1
66 #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r() */
69 * Define IDE_USES_ISA_EMULATION for slower IDE access in the ISA-IO address range
70 * If undefined, IDE access uses a seperat emulation with higher access speed.
71 * Consider to inform your Linux IDE driver about the different addresses!
72 * IDE_USES_ISA_EMULATION is only used if you define CONFIG_CMD_IDE!
74 #define IDE_USES_ISA_EMULATION
76 /*-----------------------------------------------------------------------
78 *----------------------------------------------------------------------*/
79 #define CONFIG_CONS_INDEX 1 /* Use UART0 */
80 #define CONFIG_SYS_NS16550
81 #define CONFIG_SYS_NS16550_SERIAL
82 #define CONFIG_SYS_NS16550_REG_SIZE 1
83 #define CONFIG_SYS_NS16550_CLK get_serial_clock()
84 #define CONFIG_SERIAL_MULTI
85 #undef CONFIG_SERIAL_SOFTWARE_FIFO
87 * define CONFIG_POWER_DOWN if your cpu should power down while waiting for your input
88 * Works only, if you have enabled the CONFIG_SERIAL_SOFTWARE_FIFO feature
90 #if CONFIG_SERIAL_SOFTWARE_FIFO
91 #define CONFIG_POWER_DOWN
95 * define CONFIG_SYS_CLK_FREQ to your base crystal clock in Hz
97 #define CONFIG_SYS_CLK_FREQ 33333333
100 * define CONFIG_BAUDRATE to the baudrate value you want to use as default
102 #define CONFIG_BAUDRATE 115200
103 #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
105 #define CONFIG_PREBOOT "echo;" \
106 "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
109 #undef CONFIG_BOOTARGS
111 #define CONFIG_EXTRA_ENV_SETTINGS \
113 "nfsargs=setenv bootargs root=/dev/nfs rw " \
114 "nfsroot=${serverip}:${rootpath}\0" \
115 "ramargs=setenv bootargs root=/dev/ram rw\0" \
116 "nand_args=setenv bootargs root=/dev/mtdblock5 rw" \
117 "rootfstype=jffs2\0" \
118 "addip=setenv bootargs ${bootargs} " \
119 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
120 ":${hostname}:${netdev}:off panic=1\0" \
121 "addcons=setenv bootargs ${bootargs} " \
122 "console=ttyS0,${baudrate}\0" \
123 "flash_nfs=run nfsargs addip addcons;" \
124 "bootm ${kernel_addr}\0" \
125 "flash_nand=run nand_args addip addcons;bootm ${kernel_addr}\0" \
126 "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;" \
128 "rootpath=/opt/eldk/ppc_4xx\0" \
129 "bootfile=/tftpboot/sc3/uImage\0" \
130 "u-boot=/tftpboot/sc3/u-boot.bin\0" \
131 "setup=tftp 200000 /tftpboot/sc3/setup.img;source 200000\0" \
132 "kernel_addr=FFE08000\0" \
134 #undef CONFIG_BOOTCOMMAND
136 #define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */
137 #define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
139 #if 1 /* feel free to disable for development */
140 #define CONFIG_AUTOBOOT_KEYED /* Enable password protection */
141 #define CONFIG_AUTOBOOT_PROMPT \
142 "\nSC3 - booting... stop with ENTER\n"
143 #define CONFIG_AUTOBOOT_DELAY_STR "\r" /* 1st "password" */
144 #define CONFIG_AUTOBOOT_DELAY_STR2 "\n" /* 1st "password" */
148 * define CONFIG_BOOTCOMMAND to the autoboot commands. They will running after
149 * the CONFIG_BOOTDELAY delay to boot your machine
151 #define CONFIG_BOOTCOMMAND "bootp;dcache on;bootm"
154 * define CONFIG_BOOTARGS to the default kernel parameters. They will used if you don't
155 * set different values at the u-boot prompt
157 #ifdef USE_VGA_GRAPHICS
158 #define CONFIG_BOOTARGS "root=/dev/nfs rw ip=bootp nfsroot=/tftpboot/solidcard3re"
160 #define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/nfs rw ip=bootp"
163 * Is the USB host controller assembled? If yes define CONFIG_ISP1161_PRESENT
164 * This reserves memory bank #4 for this purpose
166 #undef CONFIG_ISP1161_PRESENT
168 #undef CONFIG_LOADS_ECHO /* no echo on for serial download */
169 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
171 #define CONFIG_NET_MULTI
172 /* #define CONFIG_EEPRO100_SROM_WRITE */
173 /* #define CONFIG_SHOW_MAC */
174 #define CONFIG_EEPRO100
176 #define CONFIG_PPC4xx_EMAC
177 #define CONFIG_MII 1 /* add 405GP MII PHY management */
178 #define CONFIG_PHY_ADDR 1 /* the connected Phy defaults to address 1 */
183 #define CONFIG_BOOTP_BOOTFILESIZE
184 #define CONFIG_BOOTP_BOOTPATH
185 #define CONFIG_BOOTP_GATEWAY
186 #define CONFIG_BOOTP_HOSTNAME
190 * Command line configuration.
192 #include <config_cmd_default.h>
195 #define CONFIG_CMD_CACHE
196 #define CONFIG_CMD_DATE
197 #define CONFIG_CMD_DHCP
198 #define CONFIG_CMD_ELF
199 #define CONFIG_CMD_I2C
200 #define CONFIG_CMD_IDE
201 #define CONFIG_CMD_IRQ
202 #define CONFIG_CMD_JFFS2
203 #define CONFIG_CMD_MII
204 #define CONFIG_CMD_NAND
205 #define CONFIG_CMD_NET
206 #define CONFIG_CMD_PCI
207 #define CONFIG_CMD_PING
208 #define CONFIG_CMD_SOURCE
211 #undef CONFIG_WATCHDOG /* watchdog disabled */
214 * Miscellaneous configurable options
216 #define CONFIG_SYS_LONGHELP 1 /* undef to save memory */
217 #define CONFIG_SYS_PROMPT "SC3> " /* Monitor Command Prompt */
218 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
220 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
222 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
223 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
225 #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
226 #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
229 * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
230 * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
231 * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
232 * The Linux BASE_BAUD define should match this configuration.
233 * baseBaud = cpuClock/(uartDivisor*16)
234 * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
235 * set Linux BASE_BAUD to 403200.
237 * Consider the OPB clock! If it get lower the BASE_BAUD must be lower to
238 * (see 405GP datasheet for descritpion)
240 #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
241 #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
242 #define CONFIG_SYS_BASE_BAUD 921600 /* internal clock */
244 /* The following table includes the supported baudrates */
245 #define CONFIG_SYS_BAUDRATE_TABLE \
246 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
248 #define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */
249 #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
251 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
253 /*-----------------------------------------------------------------------
255 *-----------------------------------------------------------------------
257 #define CONFIG_HARD_I2C /* I2C with hardware support */
258 #undef CONFIG_SOFT_I2C /* I2C bit-banged */
259 #define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
263 #define I2C_TRISTATE 0
265 #define CONFIG_SYS_I2C_SPEED 100000 /* use the standard 100kHz speed */
266 #define CONFIG_SYS_I2C_SLAVE 0x7F /* mask valid bits */
268 #define CONFIG_RTC_DS1337
269 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
271 /*-----------------------------------------------------------------------
273 *-----------------------------------------------------------------------
275 #define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
276 #define PCI_HOST_FORCE 1 /* configure as pci host */
277 #define PCI_HOST_AUTO 2 /* detected via arbiter enable */
279 #define CONFIG_PCI /* include pci support */
280 #define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
281 #define CONFIG_PCI_PNP /* do pci plug-and-play */
282 /* resource configuration */
284 /* If you want to see, whats connected to your PCI bus */
285 /* #define CONFIG_PCI_SCAN_SHOW */
287 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
288 #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
289 #define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
290 #define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
291 #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
292 #define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
293 #define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
294 #define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
296 /*-----------------------------------------------------------------------
297 * External peripheral base address
298 *-----------------------------------------------------------------------
300 #if !defined(CONFIG_CMD_IDE)
302 #undef CONFIG_IDE_LED /* no led for ide supported */
303 #undef CONFIG_IDE_RESET /* no reset for ide supported */
305 /*-----------------------------------------------------------------------
307 *-----------------------------------------------------------------------
310 #define CONFIG_START_IDE 1 /* check, if use IDE */
312 #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
313 #undef CONFIG_IDE_LED /* no led for ide supported */
314 #undef CONFIG_IDE_RESET /* no reset for ide supported */
317 #define CONFIG_DOS_PARTITION
318 #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
320 #ifndef IDE_USES_ISA_EMULATION
322 /* New and faster access */
323 #define CONFIG_SYS_ATA_BASE_ADDR 0x7A000000 /* start of ISA IO emulation */
325 /* How many IDE busses are available */
326 #define CONFIG_SYS_IDE_MAXBUS 1
328 /* What IDE ports are available */
329 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x000 /* first is available */
330 #undef CONFIG_SYS_ATA_IDE1_OFFSET /* second not available */
332 /* access to the data port is calculated:
333 CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_DATA_OFFSET + 0 */
334 #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
336 /* access to the registers is calculated:
337 CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_REG_OFFSET + [1..7] */
338 #define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
340 /* access to the alternate register is calculated:
341 CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_ALT_OFFSET + 6 */
342 #define CONFIG_SYS_ATA_ALT_OFFSET 0x008 /* Offset for alternate registers */
344 #else /* IDE_USES_ISA_EMULATION */
346 #define CONFIG_SYS_ATA_BASE_ADDR 0x79000000 /* start of ISA IO emulation */
348 /* How many IDE busses are available */
349 #define CONFIG_SYS_IDE_MAXBUS 1
351 /* What IDE ports are available */
352 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* first is available */
353 #undef CONFIG_SYS_ATA_IDE1_OFFSET /* second not available */
355 /* access to the data port is calculated:
356 CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_DATA_OFFSET + 0 */
357 #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
359 /* access to the registers is calculated:
360 CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_REG_OFFSET + [1..7] */
361 #define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
363 /* access to the alternate register is calculated:
364 CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET + CONFIG_SYS_ATA_ALT_OFFSET + 6 */
365 #define CONFIG_SYS_ATA_ALT_OFFSET 0x03F0 /* Offset for alternate registers */
367 #endif /* IDE_USES_ISA_EMULATION */
372 #define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000
373 #define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000
374 #define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000
377 /*-----------------------------------------------------------------------
378 * Start addresses for the final memory configuration
379 * (Set up by the startup code)
380 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
382 * CONFIG_SYS_FLASH_BASE -> start address of internal flash
383 * CONFIG_SYS_MONITOR_BASE -> start of u-boot
385 #define CONFIG_SYS_SDRAM_BASE 0x00000000
386 #define CONFIG_SYS_FLASH_BASE 0xFFE00000
388 #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* Start of U-Boot */
389 #define CONFIG_SYS_MONITOR_LEN (0xFFFFFFFF - CONFIG_SYS_MONITOR_BASE + 1)
390 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 KiB for malloc() */
393 * For booting Linux, the board info and command line data
394 * have to be in the first 8 MiB of memory, since this is
395 * the maximum mapped by the Linux kernel during initialization.
397 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
398 /*-----------------------------------------------------------------------
399 * FLASH organization ## FIXME: lookup in datasheet
401 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
402 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
404 #define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */
405 #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver*/
406 #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector */
407 #define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/
408 #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
409 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
410 #define CONFIG_SYS_WRITE_SWAPPED_DATA /* swap Databytes between reading/writing */
412 #define CONFIG_ENV_IS_IN_FLASH 1
413 #ifdef CONFIG_ENV_IS_IN_FLASH
414 #define CONFIG_ENV_OFFSET 0x00000000 /* Offset of Environment Sector in bottom type */
415 #define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
416 #define CONFIG_ENV_SECT_SIZE 0x4000 /* see README - env sector total size */
418 /* Address and size of Redundant Environment Sector */
419 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
420 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
423 /* let us changing anything in our environment */
424 #define CONFIG_ENV_OVERWRITE
429 #define CONFIG_SYS_MAX_NAND_DEVICE 1
430 #define CONFIG_SYS_NAND_BASE 0x77D00000
432 #define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
434 /* No command line, one static partition */
435 #undef CONFIG_CMD_MTDPARTS
436 #define CONFIG_JFFS2_DEV "nand0"
437 #define CONFIG_JFFS2_PART_SIZE 0x01000000
438 #define CONFIG_JFFS2_PART_OFFSET 0x00000000
441 * Init Memory Controller:
445 #define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE
446 #define FLASH_BASE1_PRELIM 0
448 /*-----------------------------------------------------------------------
449 * Some informations about the internal SRAM (OCM=On Chip Memory)
451 * CONFIG_SYS_OCM_DATA_ADDR -> location
452 * CONFIG_SYS_OCM_DATA_SIZE -> size
455 #define CONFIG_SYS_TEMP_STACK_OCM 1
456 #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
457 #define CONFIG_SYS_OCM_DATA_SIZE 0x1000
459 /*-----------------------------------------------------------------------
460 * Definitions for initial stack pointer and data area (in DPRAM):
461 * - we are using the internal 4k SRAM, so we don't need data cache mapping
462 * - internal SRAM (OCM=On Chip Memory) is placed to CONFIG_SYS_OCM_DATA_ADDR
463 * - Stackpointer will be located to
464 * (CONFIG_SYS_INIT_RAM_ADDR&0xFFFF0000) | (CONFIG_SYS_INIT_SP_OFFSET&0x0000FFFF)
465 * in arch/powerpc/cpu/ppc4xx/start.S
468 #undef CONFIG_SYS_INIT_DCACHE_CS
469 /* Where the internal SRAM starts */
470 #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR
471 /* Where the internal SRAM ends (only offset) */
472 #define CONFIG_SYS_INIT_RAM_END 0x0F00
476 CONFIG_SYS_INIT_RAM_ADDR ------> ------------ lower address
481 CONFIG_SYS_GBL_DATA_OFFSET ----> ------------
485 CONFIG_SYS_INIT_RAM_END ------> ------------ higher address
489 /* size in bytes reserved for initial data */
490 #define CONFIG_SYS_GBL_DATA_SIZE 64
491 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
492 /* Initial value of the stack pointern in internal SRAM */
493 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
496 * Internal Definitions
500 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
501 #define BOOTFLAG_WARM 0x02 /* Software reboot */
503 /* ################################################################################### */
504 /* These defines will be used in arch/powerpc/cpu/ppc4xx/cpu_init.c to setup external chip selects */
505 /* They are currently undefined cause they are initiaized in board/solidcard3/init.S */
507 /* This chip select accesses the boot device */
508 /* It depends on boot select switch if this device is 16 or 8 bit */
510 #undef CONFIG_SYS_EBC_PB0AP
511 #undef CONFIG_SYS_EBC_PB0CR
513 #undef CONFIG_SYS_EBC_PB1AP
514 #undef CONFIG_SYS_EBC_PB1CR
516 #undef CONFIG_SYS_EBC_PB2AP
517 #undef CONFIG_SYS_EBC_PB2CR
519 #undef CONFIG_SYS_EBC_PB3AP
520 #undef CONFIG_SYS_EBC_PB3CR
522 #undef CONFIG_SYS_EBC_PB4AP
523 #undef CONFIG_SYS_EBC_PB4CR
525 #undef CONFIG_SYS_EBC_PB5AP
526 #undef CONFIG_SYS_EBC_PB5CR
528 #undef CONFIG_SYS_EBC_PB6AP
529 #undef CONFIG_SYS_EBC_PB6CR
531 #undef CONFIG_SYS_EBC_PB7AP
532 #undef CONFIG_SYS_EBC_PB7CR
534 #define CONFIG_SYS_EBC_CFG 0xb84ef000
536 #define CONFIG_SDRAM_BANK0 /* use the standard SDRAM initialization */
537 #undef CONFIG_SPD_EEPROM
540 * Define this to get more information about system configuration
542 /* #define SC3_DEBUGOUT */
545 /***********************************************************************
546 * External peripheral base address
547 ***********************************************************************/
549 #define CONFIG_SYS_ISA_MEM_BASE_ADDRESS 0x78000000
551 Die Grafik-Treiber greifen über die Adresse in diesem Macro auf den Chip zu.
552 Das funktioniert bei deren Karten, weil sie eine PCI-Bridge benutzen, die
553 das gleiche Mapping durchführen kann, wie der SC520 (also Aufteilen von IO-Zugriffen
554 auf ISA- und PCI-Zyklen)
556 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000
557 /*#define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0x79000000 */
559 /************************************************************
561 ************************************************************/
563 #ifdef USE_VGA_GRAPHICS
564 #define CONFIG_VIDEO /* To enable video controller support */
565 #define CONFIG_VIDEO_CT69000
566 #define CONFIG_CFB_CONSOLE
567 /* #define CONFIG_VIDEO_LOGO */
568 #define CONFIG_VGA_AS_SINGLE_DEVICE
569 #define CONFIG_VIDEO_SW_CURSOR
570 /* #define CONFIG_VIDEO_HW_CURSOR */
571 #define CONFIG_VIDEO_ONBOARD /* Video controller is on-board */
573 #define VIDEO_HW_RECTFILL
574 #define VIDEO_HW_BITBLT
578 /************************************************************
580 ************************************************************/
581 #define CONFIG_SC3_VERSION "r1.4"
583 #define POST_OUT(x) (*((volatile unsigned char*)(0x79000080))=x)
585 #endif /* __CONFIG_H */