include/configs/sama5d2_xplained.h

   1 /*
   2  * Configuration file for the SAMA5D2 Xplained Board.
   3  *
   4  * Copyright (C) 2015 Atmel Corporation
   5  *                    Wenyou Yang <wenyou.yang@atmel.com>
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 /* No NOR flash, this definition should put before common header */
  14 #define CONFIG_SYS_NO_FLASH
  15
  16 #include "at91-sama5_common.h"
  17
  18 #define CONFIG_MISC_INIT_R
  19
  20 /* SDRAM */
  21 #define CONFIG_NR_DRAM_BANKS            1
  22 #define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
  23 #define CONFIG_SYS_SDRAM_SIZE           0x20000000
  24
  25 #ifdef CONFIG_SPL_BUILD
  26 #define CONFIG_SYS_INIT_SP_ADDR         0x210000
  27 #else
  28 #define CONFIG_SYS_INIT_SP_ADDR \
  29         (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
  30 #endif
  31
  32 #define CONFIG_SYS_LOAD_ADDR            0x22000000 /* load address */
  33
  34 /* SerialFlash */
  35 #ifdef CONFIG_CMD_SF
  36 #define CONFIG_SF_DEFAULT_BUS           0
  37 #define CONFIG_SF_DEFAULT_CS            0
  38 #define CONFIG_SF_DEFAULT_SPEED         30000000
  39 #endif
  40
  41 /* NAND flash */
  42 #undef CONFIG_CMD_NAND
  43
  44 /* MMC */
  45 #ifdef CONFIG_CMD_MMC
  46 #define CONFIG_GENERIC_MMC
  47 #define CONFIG_SDHCI
  48 #endif
  49
  50 /* USB device */
  51 #define CONFIG_USB_ETHER
  52 #define CONFIG_USB_ETH_RNDIS
  53 #define CONFIG_USBNET_MANUFACTURER      "Atmel SAMA5D2 XPlained"
  54
  55 #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
  56 #define CONFIG_DOS_PARTITION
  57 #endif
  58
  59 /* I2C */
  60 #define AT24MAC_ADDR            0x5c
  61 #define AT24MAC_REG             0x9a
  62
  63 /* Ethernet Hardware */
  64 #define CONFIG_MACB
  65 #define CONFIG_RMII
  66 #define CONFIG_NET_RETRY_COUNT          20
  67 #define CONFIG_MACB_SEARCH_PHY
  68
  69 /* LCD */
  70
  71 #ifdef CONFIG_LCD
  72 #define LCD_BPP                         LCD_COLOR16
  73 #define LCD_OUTPUT_BPP                  24
  74 #define CONFIG_LCD_LOGO
  75 #define CONFIG_LCD_INFO
  76 #define CONFIG_LCD_INFO_BELOW_LOGO
  77 #define CONFIG_SYS_WHITE_ON_BLACK
  78 #define CONFIG_ATMEL_HLCD
  79 #define CONFIG_ATMEL_LCD_RGB565
  80 #endif
  81
  82 #ifdef CONFIG_SYS_USE_MMC
  83
  84 /* bootstrap + u-boot + env in sd card */
  85 #undef FAT_ENV_DEVICE_AND_PART
  86 #undef CONFIG_BOOTCOMMAND
  87
  88 #define FAT_ENV_DEVICE_AND_PART "1"
  89 #define CONFIG_BOOTCOMMAND      "fatload mmc 1:1 0x21000000 at91-sama5d2_xplained.dtb; " \
  90                                 "fatload mmc 1:1 0x22000000 zImage; " \
  91                                 "bootz 0x22000000 - 0x21000000"
  92 #undef CONFIG_BOOTARGS
  93 #define CONFIG_BOOTARGS \
  94         "console=ttyS0,115200 earlyprintk root=/dev/mmcblk1p2 rw rootwait"
  95
  96 #endif
  97
  98 /* SPL */
  99 #define CONFIG_SPL_FRAMEWORK
 100 #define CONFIG_SPL_TEXT_BASE            0x200000
 101 #define CONFIG_SPL_MAX_SIZE             0x10000
 102 #define CONFIG_SPL_BSS_START_ADDR       0x20000000
 103 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 104 #define CONFIG_SYS_SPL_MALLOC_START     0x20080000
 105 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x80000
 106
 107 #define CONFIG_SPL_BOARD_INIT
 108 #define CONFIG_SYS_MONITOR_LEN          (512 << 10)
 109
 110 #ifdef CONFIG_SYS_USE_MMC
 111 #define CONFIG_SPL_LDSCRIPT             arch/arm/mach-at91/armv7/u-boot-spl.lds
 112 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS      0x400
 113 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
 114 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
 115 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME         "u-boot.img"
 116
 117 #elif CONFIG_SYS_USE_SERIALFLASH
 118 #define CONFIG_SPL_SPI_LOAD
 119 #define CONFIG_SYS_SPI_U_BOOT_OFFS      0x8000
 120
 121 #endif
 122
 123 #endif