include/configs/omapl138_lcdk.h

   1 /*
   2  * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
   3  *
   4  * Based on davinci_dvevm.h. Original Copyrights follow:
   5  *
   6  * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0
   9  */
  10
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * Board
  16  */
  17 #define CONFIG_DRIVER_TI_EMAC
  18 #undef CONFIG_USE_SPIFLASH
  19 #undef  CONFIG_SYS_USE_NOR
  20 #define CONFIG_USE_NAND
  21
  22 /*
  23 * Disable DM_* for SPL build and can be re-enabled after adding
  24 * DM support in SPL
  25 */
  26 #ifdef CONFIG_SPL_BUILD
  27 #undef CONFIG_DM_I2C
  28 #undef CONFIG_DM_I2C_COMPAT
  29 #endif
  30 /*
  31  * SoC Configuration
  32  */
  33 #define CONFIG_MACH_OMAPL138_LCDK
  34 #define CONFIG_SYS_CLK_FREQ             clk_get(DAVINCI_ARM_CLKID)
  35 #define CONFIG_SYS_OSCIN_FREQ           24000000
  36 #define CONFIG_SYS_TIMERBASE            DAVINCI_TIMER0_BASE
  37 #define CONFIG_SYS_HZ_CLOCK             clk_get(DAVINCI_AUXCLK_CLKID)
  38 #define CONFIG_SYS_HZ                   1000
  39 #define CONFIG_SKIP_LOWLEVEL_INIT
  40
  41 /*
  42  * Memory Info
  43  */
  44 #define CONFIG_SYS_MALLOC_LEN   (0x10000 + 1*1024*1024) /* malloc() len */
  45 #define PHYS_SDRAM_1            DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
  46 #define PHYS_SDRAM_1_SIZE       (128 << 20) /* SDRAM size 128MB */
  47 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
  48
  49 /* memtest start addr */
  50 #define CONFIG_SYS_MEMTEST_START        (PHYS_SDRAM_1 + 0x2000000)
  51
  52 /* memtest will be run on 16MB */
  53 #define CONFIG_SYS_MEMTEST_END  (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
  54
  55 #define CONFIG_NR_DRAM_BANKS    1 /* we have 1 bank of DRAM */
  56
  57 #define CONFIG_SYS_DA850_SYSCFG_SUSPSRC (       \
  58         DAVINCI_SYSCFG_SUSPSRC_TIMER0 |         \
  59         DAVINCI_SYSCFG_SUSPSRC_SPI1 |           \
  60         DAVINCI_SYSCFG_SUSPSRC_UART2 |          \
  61         DAVINCI_SYSCFG_SUSPSRC_EMAC |           \
  62         DAVINCI_SYSCFG_SUSPSRC_I2C)
  63
  64 /*
  65  * PLL configuration
  66  */
  67
  68 /* Requires CONFIG_SYS_DA850_PLL0_POSTDIV=0, set in Kconfig */
  69 #define CONFIG_SYS_DA850_PLL0_PLLM     18
  70 #define CONFIG_SYS_DA850_PLL1_PLLM     21
  71
  72 /*
  73  * DDR2 memory configuration
  74  */
  75 #define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
  76                                         DV_DDR_PHY_EXT_STRBEN | \
  77                                         (0x5 << DV_DDR_PHY_RD_LATENCY_SHIFT))
  78
  79 #define CONFIG_SYS_DA850_DDR2_SDBCR (             \
  80         (1 << DV_DDR_SDCR_DDR2EN_SHIFT)         | \
  81         (1 << DV_DDR_SDCR_DDREN_SHIFT)          | \
  82         (1 << DV_DDR_SDCR_SDRAMEN_SHIFT)        | \
  83         (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT)      | \
  84         (4 << DV_DDR_SDCR_CL_SHIFT)             | \
  85         (3 << DV_DDR_SDCR_IBANK_SHIFT)          | \
  86         (2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
  87
  88 /* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
  89 #define CONFIG_SYS_DA850_DDR2_SDBCR2 0
  90
  91 #define CONFIG_SYS_DA850_DDR2_SDTIMR (            \
  92         (19 << DV_DDR_SDTMR1_RFC_SHIFT)         | \
  93         (1 << DV_DDR_SDTMR1_RP_SHIFT)           | \
  94         (1 << DV_DDR_SDTMR1_RCD_SHIFT)          | \
  95         (2 << DV_DDR_SDTMR1_WR_SHIFT)           | \
  96         (6 << DV_DDR_SDTMR1_RAS_SHIFT)          | \
  97         (8 << DV_DDR_SDTMR1_RC_SHIFT)           | \
  98         (1 << DV_DDR_SDTMR1_RRD_SHIFT)          | \
  99         (1 << DV_DDR_SDTMR1_WTR_SHIFT))
 100
 101 #define CONFIG_SYS_DA850_DDR2_SDTIMR2 (           \
 102         (7 << DV_DDR_SDTMR2_RASMAX_SHIFT)       | \
 103         (2 << DV_DDR_SDTMR2_XP_SHIFT)           | \
 104         (0 << DV_DDR_SDTMR2_ODT_SHIFT)          | \
 105         (20 << DV_DDR_SDTMR2_XSNR_SHIFT)        | \
 106         (199 << DV_DDR_SDTMR2_XSRD_SHIFT)       | \
 107         (1 << DV_DDR_SDTMR2_RTP_SHIFT)          | \
 108         (2 << DV_DDR_SDTMR2_CKE_SHIFT))
 109
 110 #define CONFIG_SYS_DA850_DDR2_SDRCR    0x00000492
 111 #define CONFIG_SYS_DA850_DDR2_PBBPR    0x30
 112
 113 /*
 114  * Serial Driver info
 115  */
 116 #define CONFIG_SYS_NS16550_CLK  clk_get(DAVINCI_UART2_CLKID)
 117 #if !defined(CONFIG_DM_SERIAL)
 118 #define CONFIG_SYS_NS16550_SERIAL
 119 #define CONFIG_SYS_NS16550_REG_SIZE     -4      /* NS16550 register size */
 120 #define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */
 121 #define CONFIG_SYS_NS16550_CLK  clk_get(DAVINCI_UART2_CLKID)
 122 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
 123 #endif
 124
 125 #define CONFIG_SYS_SPI_BASE             DAVINCI_SPI1_BASE
 126 #define CONFIG_SYS_SPI_CLK              clk_get(DAVINCI_SPI1_CLKID)
 127 #define CONFIG_SF_DEFAULT_SPEED         30000000
 128 #define CONFIG_ENV_SPI_MAX_HZ   CONFIG_SF_DEFAULT_SPEED
 129
 130 #ifdef CONFIG_USE_SPIFLASH
 131 #define CONFIG_SYS_SPI_U_BOOT_OFFS      0x8000
 132 #define CONFIG_SYS_SPI_U_BOOT_SIZE      0x30000
 133 #endif
 134
 135 /*
 136  * I2C Configuration
 137  */
 138 #define CONFIG_SYS_I2C_DAVINCI
 139 #define CONFIG_SYS_DAVINCI_I2C_SPEED    25000
 140 #define CONFIG_SYS_DAVINCI_I2C_SLAVE    10 /* Bogus, master-only in U-Boot */
 141 #define CONFIG_SYS_I2C_EXPANDER_ADDR    0x20
 142
 143 /*
 144  * Flash & Environment
 145  */
 146 #ifdef CONFIG_USE_NAND
 147 #define CONFIG_NAND_DAVINCI
 148 #define CONFIG_ENV_OFFSET               0x0 /* Block 0--not used by bootcode */
 149 #define CONFIG_ENV_SIZE                 (128 << 9)
 150 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 151 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
 152 #define CONFIG_SYS_NAND_PAGE_2K
 153 #define CONFIG_SYS_NAND_CS              3
 154 #define CONFIG_SYS_NAND_BASE            DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
 155 #define CONFIG_SYS_NAND_MASK_CLE        0x10
 156 #define CONFIG_SYS_NAND_MASK_ALE        0x8
 157 #undef CONFIG_SYS_NAND_HW_ECC
 158 #define CONFIG_SYS_MAX_NAND_DEVICE      1 /* Max number of NAND devices */
 159 #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
 160 #define CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
 161 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 162 #define CONFIG_SYS_NAND_PAGE_SIZE       (2 << 10)
 163 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 << 10)
 164 #define CONFIG_SYS_NAND_U_BOOT_SIZE     SZ_512K
 165 #define CONFIG_SYS_NAND_U_BOOT_DST      0xc1080000
 166 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_NAND_U_BOOT_DST
 167 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \
 168                                         CONFIG_SYS_NAND_U_BOOT_SIZE - \
 169                                         CONFIG_SYS_MALLOC_LEN -       \
 170                                         GENERATED_GBL_DATA_SIZE)
 171 #define CONFIG_SYS_NAND_ECCPOS          {                               \
 172                                 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,     \
 173                                 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, \
 174                                 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, \
 175                                 54, 55, 56, 57, 58, 59, 60, 61, 62, 63 }
 176 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 177 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
 178 #define CONFIG_SYS_NAND_ECCSIZE         512
 179 #define CONFIG_SYS_NAND_ECCBYTES        10
 180 #define CONFIG_SYS_NAND_OOBSIZE         64
 181 #define CONFIG_SPL_NAND_BASE
 182 #define CONFIG_SPL_NAND_DRIVERS
 183 #define CONFIG_SPL_NAND_ECC
 184 #define CONFIG_SPL_NAND_LOAD
 185 #endif
 186
 187 #ifdef CONFIG_SYS_USE_NOR
 188 #define CONFIG_FLASH_CFI_DRIVER
 189 #define CONFIG_SYS_FLASH_CFI
 190 #define CONFIG_SYS_FLASH_PROTECTION
 191 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* max number of flash banks */
 192 #define CONFIG_SYS_FLASH_SECT_SZ        (128 << 10) /* 128KB */
 193 #define CONFIG_ENV_OFFSET               (CONFIG_SYS_FLASH_SECT_SZ * 3)
 194 #define CONFIG_ENV_SIZE                 (128 << 10)
 195 #define CONFIG_SYS_FLASH_BASE           DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
 196 #define PHYS_FLASH_SIZE                 (8 << 20) /* Flash size 8MB */
 197 #define CONFIG_SYS_MAX_FLASH_SECT ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)\
 198                + 3)
 199 #define CONFIG_ENV_SECT_SIZE            CONFIG_SYS_FLASH_SECT_SZ
 200 #endif
 201
 202 #ifdef CONFIG_USE_SPIFLASH
 203 #define CONFIG_ENV_SIZE                 (64 << 10)
 204 #define CONFIG_ENV_OFFSET               (256 << 10)
 205 #define CONFIG_ENV_SECT_SIZE            (64 << 10)
 206 #endif
 207
 208 /*
 209  * Network & Ethernet Configuration
 210  */
 211 #ifdef CONFIG_DRIVER_TI_EMAC
 212 #define CONFIG_MII
 213 #undef  CONFIG_DRIVER_TI_EMAC_USE_RMII
 214 #define CONFIG_BOOTP_DEFAULT
 215 #define CONFIG_BOOTP_DNS2
 216 #define CONFIG_BOOTP_SEND_HOSTNAME
 217 #define CONFIG_NET_RETRY_COUNT  10
 218 #endif
 219
 220 /*
 221  * U-Boot general configuration
 222  */
 223 #define CONFIG_MISC_INIT_R
 224 #define CONFIG_BOOTFILE         "zImage" /* Boot file name */
 225 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 226 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
 227 #define CONFIG_SYS_LOAD_ADDR    (PHYS_SDRAM_1 + 0x700000)
 228 #define CONFIG_MX_CYCLIC
 229
 230 /*
 231  * Linux Information
 232  */
 233 #define LINUX_BOOT_PARAM_ADDR   (PHYS_SDRAM_1 + 0x100)
 234 #define CONFIG_CMDLINE_TAG
 235 #define CONFIG_REVISION_TAG
 236 #define CONFIG_SETUP_MEMORY_TAGS
 237 #define CONFIG_BOOTCOMMAND \
 238                 "run envboot; " \
 239                 "run mmcboot; "
 240
 241 #define DEFAULT_LINUX_BOOT_ENV \
 242         "loadaddr=0xc0700000\0" \
 243         "fdtaddr=0xc0600000\0" \
 244         "scriptaddr=0xc0600000\0"
 245
 246 #include <environment/ti/mmc.h>
 247
 248 #define CONFIG_EXTRA_ENV_SETTINGS \
 249         DEFAULT_LINUX_BOOT_ENV \
 250         DEFAULT_MMC_TI_ARGS \
 251         "bootpart=0:2\0" \
 252         "bootdir=/boot\0" \
 253         "bootfile=zImage\0" \
 254         "fdtfile=da850-lcdk.dtb\0" \
 255         "boot_fdt=yes\0" \
 256         "boot_fit=0\0" \
 257         "console=ttyS2,115200n8\0"
 258
 259 #ifdef CONFIG_CMD_BDI
 260 #define CONFIG_CLOCKS
 261 #endif
 262
 263 #ifndef CONFIG_DRIVER_TI_EMAC
 264 #endif
 265
 266 #ifdef CONFIG_USE_NAND
 267 #define CONFIG_MTD_DEVICE
 268 #define CONFIG_MTD_PARTITIONS
 269 #endif
 270
 271 #if !defined(CONFIG_USE_NAND) && \
 272         !defined(CONFIG_SYS_USE_NOR) && \
 273         !defined(CONFIG_USE_SPIFLASH)
 274 #define CONFIG_ENV_SIZE         (16 << 10)
 275 #endif
 276
 277 /* SD/MMC */
 278
 279 #ifdef CONFIG_ENV_IS_IN_MMC
 280 #undef CONFIG_ENV_SIZE
 281 #undef CONFIG_ENV_OFFSET
 282 #define CONFIG_ENV_SIZE         (16 << 10)      /* 16 KiB */
 283 #define CONFIG_ENV_OFFSET       (51 << 9)       /* Sector 51 */
 284 #endif
 285
 286 #ifndef CONFIG_DIRECT_NOR_BOOT
 287 /* defines for SPL */
 288 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SYS_TEXT_BASE - \
 289                                                 CONFIG_SYS_MALLOC_LEN)
 290 #define CONFIG_SYS_SPL_MALLOC_SIZE      CONFIG_SYS_MALLOC_LEN
 291 #define CONFIG_SPL_STACK        0x8001ff00
 292 #define CONFIG_SPL_TEXT_BASE    0x80000000
 293 #define CONFIG_SPL_MAX_FOOTPRINT        32768
 294 #define CONFIG_SPL_PAD_TO       32768
 295 #endif
 296
 297 /* additions for new relocation code, must added to all boards */
 298 #define CONFIG_SYS_SDRAM_BASE           0xc0000000
 299 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
 300                                         GENERATED_GBL_DATA_SIZE)
 301
 302 #include <asm/arch/hardware.h>
 303
 304 #endif /* __CONFIG_H */