omap3_beagle: Change NAND ECC scheme back to OMAP_ECC_HAM1_CODE_HW
[platform/kernel/u-boot.git] / include / configs / omap3_beagle.h
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * (C) Copyright 2006-2008
4  * Texas Instruments.
5  * Richard Woodruff <r-woodruff2@ti.com>
6  * Syed Mohammed Khasim <x0khasim@ti.com>
7  *
8  * Configuration settings for the TI OMAP3530 Beagle board.
9  */
10
11 #ifndef __CONFIG_H
12 #define __CONFIG_H
13
14 #include <configs/ti_omap3_common.h>
15
16 /*
17  * We are only ever GP parts and will utilize all of the "downloaded image"
18  * area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB).
19  */
20
21 #define CONFIG_CMDLINE_TAG
22 #define CONFIG_SETUP_MEMORY_TAGS
23 #define CONFIG_INITRD_TAG
24 #define CONFIG_REVISION_TAG
25
26 /* NAND */
27 #if defined(CONFIG_MTD_RAW_NAND)
28 #define CONFIG_SYS_FLASH_BASE           NAND_BASE
29 #define CONFIG_SYS_MAX_NAND_DEVICE      1
30 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
31 #define CONFIG_SYS_NAND_PAGE_COUNT      64
32 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
33 #define CONFIG_SYS_NAND_OOBSIZE         64
34 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128*1024)
35 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   NAND_LARGE_BADBLOCK_POS
36 #define CONFIG_SYS_NAND_ECCPOS          {2, 3, 4, 5, 6, 7, 8, 9,\
37                                          10, 11, 12, 13}
38 #define CONFIG_SYS_NAND_ECCSIZE         512
39 #define CONFIG_SYS_NAND_ECCBYTES        3
40 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_HAM1_CODE_HW
41 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
42 #define CONFIG_SYS_ENV_SECT_SIZE        SZ_128K
43 #define CONFIG_ENV_OVERWRITE
44 /* NAND: SPL falcon mode configs */
45 #if defined(CONFIG_SPL_OS_BOOT)
46 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x2a0000
47 #endif /* CONFIG_SPL_OS_BOOT */
48 #endif /* CONFIG_MTD_RAW_NAND */
49
50 /* USB EHCI */
51 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO        147
52
53 /* Enable Multi Bus support for I2C */
54 #define CONFIG_I2C_MULTI_BUS
55
56 /* DSS Support */
57
58 /* TWL4030 LED Support */
59
60 #define MEM_LAYOUT_ENV_SETTINGS \
61         DEFAULT_LINUX_BOOT_ENV
62
63 #define BOOTENV_DEV_LEGACY_MMC(devtypeu, devtypel, instance) \
64         "bootcmd_" #devtypel #instance "=" \
65         "setenv mmcdev " #instance "; " \
66         "run mmcboot\0"
67 #define BOOTENV_DEV_NAME_LEGACY_MMC(devtypeu, devtypel, instance) \
68         #devtypel #instance " "
69
70 #if defined(CONFIG_MTD_RAW_NAND)
71
72 #define BOOTENV_DEV_NAND(devtypeu, devtypel, instance) \
73         "bootcmd_" #devtypel #instance "=" \
74         "if test ${mtdids} = '' || test ${mtdparts} = '' ; then " \
75                 "echo NAND boot disabled: No mtdids and/or mtdparts; " \
76         "else " \
77                 "run nandboot; " \
78         "fi\0"
79 #define BOOTENV_DEV_NAME_NAND(devtypeu, devtypel, instance) \
80         #devtypel #instance " "
81
82 #define BOOT_TARGET_DEVICES(func) \
83         func(MMC, mmc, 0) \
84         func(LEGACY_MMC, legacy_mmc, 0) \
85         func(UBIFS, ubifs, 0) \
86         func(NAND, nand, 0)
87
88 #else /* !CONFIG_MTD_RAW_NAND */
89
90 #define BOOT_TARGET_DEVICES(func) \
91         func(MMC, mmc, 0) \
92         func(LEGACY_MMC, legacy_mmc, 0)
93
94 #endif /* CONFIG_MTD_RAW_NAND */
95
96 #include <config_distro_bootcmd.h>
97
98 #define CONFIG_EXTRA_ENV_SETTINGS \
99         MEM_LAYOUT_ENV_SETTINGS \
100         "fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
101         "fdt_high=0xffffffff\0" \
102         "console=ttyO2,115200n8\0" \
103         "bootdir=/boot\0" \
104         "bootenv=uEnv.txt\0" \
105         "bootfile=zImage\0" \
106         "bootpart=0:2\0" \
107         "bootubivol=rootfs\0" \
108         "bootubipart=rootfs\0" \
109         "usbtty=cdc_acm\0" \
110         "mpurate=auto\0" \
111         "buddy=none\0" \
112         "camera=none\0" \
113         "vram=12M\0" \
114         "dvimode=640x480MR-16@60\0" \
115         "defaultdisplay=dvi\0" \
116         "defaultargs=setenv defargs " \
117                 "mpurate=${mpurate} " \
118                 "buddy=${buddy} "\
119                 "camera=${camera} "\
120                 "vram=${vram} " \
121                 "omapfb.mode=dvi:${dvimode} " \
122                 "omapdss.def_disp=${defaultdisplay}\0" \
123         "optargs=\0" \
124         "findfdt=" \
125                 "if test $beaglerev = AxBx; then " \
126                         "setenv fdtfile omap3-beagle.dtb; fi; " \
127                 "if test $beaglerev = Cx; then " \
128                         "setenv fdtfile omap3-beagle.dtb; fi; " \
129                 "if test $beaglerev = C4; then " \
130                         "setenv fdtfile omap3-beagle.dtb; fi; " \
131                 "if test $beaglerev = xMAB; then " \
132                         "setenv fdtfile omap3-beagle-xm-ab.dtb; fi; " \
133                 "if test $beaglerev = xMC; then " \
134                         "setenv fdtfile omap3-beagle-xm.dtb; fi; " \
135                 "if test $fdtfile = undefined; then " \
136                         "echo WARNING: Could not determine device tree to use; fi\0" \
137         "mmcdev=0\0" \
138         "mmcpart=2\0" \
139         "mmcroot=/dev/mmcblk0p2 rw\0" \
140         "mmcrootfstype=ext4 rootwait\0" \
141         "mmcargs=run defaultargs; setenv bootargs console=${console} " \
142                 "${mtdparts} " \
143                 "${defargs} " \
144                 "${optargs} " \
145                 "root=${mmcroot} " \
146                 "rootfstype=${mmcrootfstype}\0" \
147         "userbutton_xm=gpio input 4;\0" \
148         "userbutton_nonxm=gpio input 7;\0" \
149         "userbutton=if gpio input 173; then " \
150                         "run userbutton_xm; " \
151                 "else " \
152                         "run userbutton_nonxm; " \
153                 "fi;\0" \
154         "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
155         "ext4bootenv=ext4load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootenv}\0" \
156         "importbootenv=echo Importing environment from mmc${mmcdev} ...; " \
157                 "env import -t ${loadaddr} ${filesize}\0" \
158         "mmcbootenv=setenv bootpart ${mmcdev}:${mmcpart}; " \
159                 "mmc dev ${mmcdev}; " \
160                 "if mmc rescan; then " \
161                         "if run userbutton; then " \
162                                 "setenv bootenv uEnv.txt;" \
163                         "else " \
164                                 "setenv bootenv user.txt;" \
165                         "fi;" \
166                         "run loadbootenv && run importbootenv; " \
167                         "run ext4bootenv && run importbootenv; " \
168                         "if test -n $uenvcmd; then " \
169                                 "echo Running uenvcmd ...; " \
170                                 "run uenvcmd; " \
171                         "fi; " \
172                 "fi\0" \
173         "validatefdt=" \
174                 "if test $beaglerev = xMAB; then " \
175                         "if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile}; then " \
176                                 "setenv fdtfile omap3-beagle-xm.dtb; " \
177                         "fi; " \
178                 "fi; \0" \
179         "loadimage=ext4load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
180         "loaddtb=run validatefdt; ext4load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
181         "mmcboot=run mmcbootenv; " \
182                 "if run loadimage && run loaddtb; then " \
183                         "echo Booting ${bootdir}/${bootfile} from mmc ${bootpart} ...; " \
184                         "run mmcargs; " \
185                         "if test ${bootfile} = uImage; then " \
186                                 "bootm ${loadaddr} - ${fdtaddr}; " \
187                         "fi; " \
188                         "if test ${bootfile} = zImage; then " \
189                                 "bootz ${loadaddr} - ${fdtaddr}; " \
190                         "fi; " \
191                 "fi\0" \
192         "nandroot=ubi0:rootfs ubi.mtd=rootfs rw\0" \
193         "nandrootfstype=ubifs rootwait\0" \
194         "nandargs=run defaultargs; setenv bootargs console=${console} " \
195                 "${mtdparts} " \
196                 "${defargs} " \
197                 "${optargs} " \
198                 "root=${nandroot} " \
199                 "rootfstype=${nandrootfstype}\0" \
200         "nandboot=if nand read ${loadaddr} kernel && nand read ${fdtaddr} dtb; then " \
201                         "echo Booting uImage from NAND MTD 'kernel' partition ...; " \
202                         "run nandargs; " \
203                         "bootm ${loadaddr} - ${fdtaddr}; " \
204                 "fi\0" \
205         "loadramdisk=ext4load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
206         "ramdisk=rootfs.ext2.gz.uboot\0" \
207         "ramdisk_size=16384\0" \
208         "ramroot=/dev/ram rw\0" \
209         "ramrootfstype=ext2\0" \
210         "ramargs=run defaultargs; setenv bootargs console=${console} " \
211                 "${mtdparts} " \
212                 "${defargs} " \
213                 "${optargs} " \
214                 "root=${ramroot} ramdisk_size=${ramdisk_size} " \
215                 "rootfstype=${ramrootfstype}\0" \
216         "ramboot=run mmcbootenv; " \
217                 "if run loadimage && run loaddtb && run loadramdisk; then " \
218                         "echo Booting ${bootdir}/${bootfile} from mmc ${bootpart} w/ramdisk ...; " \
219                         "run ramargs; " \
220                         "bootz ${loadaddr} ${rdaddr} ${fdtaddr}; " \
221                 "fi\0" \
222         BOOTENV
223
224 #endif /* __CONFIG_H */