include/configs/omap3_beagle.h

   1 /*
   2  * (C) Copyright 2006-2008
   3  * Texas Instruments.
   4  * Richard Woodruff <r-woodruff2@ti.com>
   5  * Syed Mohammed Khasim <x0khasim@ti.com>
   6  *
   7  * Configuration settings for the TI OMAP3530 Beagle board.
   8  *
   9  * SPDX-License-Identifier:     GPL-2.0+
  10  */
  11
  12 #ifndef __CONFIG_H
  13 #define __CONFIG_H
  14
  15 #define CONFIG_NR_DRAM_BANKS    2       /* CS1 may or may not be populated */
  16
  17 /*
  18  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
  19  * 64 bytes before this address should be set aside for u-boot.img's
  20  * header. That is 0x800FFFC0--0x80100000 should not be used for any
  21  * other needs.  We use this rather than the inherited defines from
  22  * ti_armv7_common.h for backwards compatibility.
  23  */
  24 #define CONFIG_SYS_TEXT_BASE            0x80100000
  25 #define CONFIG_SPL_BSS_START_ADDR       0x80000000
  26 #define CONFIG_SPL_BSS_MAX_SIZE         (512 << 10)     /* 512 KB */
  27 #define CONFIG_SYS_SPL_MALLOC_START     0x80208000
  28 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  29
  30 #include <configs/ti_omap3_common.h>
  31
  32 /*
  33  * Display CPU and Board information
  34  */
  35 #define CONFIG_DISPLAY_CPUINFO          1
  36 #define CONFIG_DISPLAY_BOARDINFO        1
  37
  38 #define CONFIG_MISC_INIT_R
  39
  40 #define CONFIG_REVISION_TAG             1
  41 #define CONFIG_ENV_OVERWRITE
  42
  43 /* Status LED */
  44 #define CONFIG_STATUS_LED               1
  45 #define CONFIG_BOARD_SPECIFIC_LED       1
  46 #define STATUS_LED_BIT                  0x01
  47 #define STATUS_LED_STATE                STATUS_LED_ON
  48 #define STATUS_LED_PERIOD               (CONFIG_SYS_HZ / 2)
  49 #define STATUS_LED_BIT1                 0x02
  50 #define STATUS_LED_STATE1               STATUS_LED_ON
  51 #define STATUS_LED_PERIOD1              (CONFIG_SYS_HZ / 2)
  52 #define STATUS_LED_BOOT                 STATUS_LED_BIT
  53 #define STATUS_LED_GREEN                STATUS_LED_BIT1
  54
  55 /* Enable Multi Bus support for I2C */
  56 #define CONFIG_I2C_MULTI_BUS            1
  57
  58 /* Probe all devices */
  59 #define CONFIG_SYS_I2C_NOPROBES         {{0x0, 0x0}}
  60
  61 /* USB */
  62 #define CONFIG_USB_MUSB_GADGET
  63 #define CONFIG_USB_MUSB_OMAP2PLUS
  64 #define CONFIG_USB_MUSB_PIO_ONLY
  65 #define CONFIG_USB_GADGET_DUALSPEED
  66 #define CONFIG_TWL4030_USB              1
  67 #define CONFIG_USB_ETHER
  68 #define CONFIG_USB_ETHER_RNDIS
  69 #define CONFIG_USB_GADGET_VBUS_DRAW     0
  70 #define CONFIG_USB_GADGET_DOWNLOAD
  71 #define CONFIG_G_DNL_VENDOR_NUM         0x0451
  72 #define CONFIG_G_DNL_PRODUCT_NUM        0xd022
  73 #define CONFIG_G_DNL_MANUFACTURER       "TI"
  74 #define CONFIG_USB_FUNCTION_FASTBOOT
  75 #define CONFIG_CMD_FASTBOOT
  76 #define CONFIG_ANDROID_BOOT_IMAGE
  77 #define CONFIG_FASTBOOT_BUF_ADDR        CONFIG_SYS_LOAD_ADDR
  78 #define CONFIG_FASTBOOT_BUF_SIZE        0x07000000
  79
  80 /* USB EHCI */
  81 #define CONFIG_CMD_USB
  82 #define CONFIG_USB_EHCI
  83
  84 #define CONFIG_USB_EHCI_OMAP
  85 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO        147
  86
  87 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
  88 #define CONFIG_USB_HOST_ETHER
  89 #define CONFIG_USB_ETHER_ASIX
  90 #define CONFIG_USB_ETHER_MCS7830
  91 #define CONFIG_USB_ETHER_SMSC95XX
  92
  93 /* GPIO banks */
  94 #define CONFIG_OMAP3_GPIO_5             /* GPIO128..159 is in GPIO bank 5 */
  95 #define CONFIG_OMAP3_GPIO_6             /* GPIO160..191 is in GPIO bank 6 */
  96
  97 /* commands to include */
  98 #define CONFIG_CMD_ASKENV
  99
 100 #define CONFIG_CMD_CACHE
 101
 102 #define MTDIDS_DEFAULT                  "nand0=nand"
 103 #define MTDPARTS_DEFAULT                "mtdparts=nand:512k(x-loader),"\
 104                                         "1920k(u-boot),128k(u-boot-env),"\
 105                                         "4m(kernel),-(fs)"
 106
 107 #define CONFIG_USB_STORAGE      /* USB storage support          */
 108 #define CONFIG_CMD_NAND         /* NAND support                 */
 109 #define CONFIG_CMD_LED          /* LED support                  */
 110 #define CONFIG_CMD_DHCP
 111
 112 #define CONFIG_VIDEO_OMAP3      /* DSS Support                  */
 113
 114 /*
 115  * TWL4030
 116  */
 117 #define CONFIG_TWL4030_LED              1
 118
 119 /*
 120  * Board NAND Info.
 121  */
 122 #define CONFIG_NAND_OMAP_GPMC
 123 #define CONFIG_SYS_MAX_NAND_DEVICE      1               /* Max number of NAND */
 124                                                         /* devices */
 125
 126 #define CONFIG_EXTRA_ENV_SETTINGS \
 127         "loadaddr=0x80200000\0" \
 128         "rdaddr=0x81000000\0" \
 129         "fdt_high=0xffffffff\0" \
 130         "fdtaddr=0x80f80000\0" \
 131         "usbtty=cdc_acm\0" \
 132         "bootfile=uImage\0" \
 133         "ramdisk=ramdisk.gz\0" \
 134         "bootdir=/boot\0" \
 135         "bootpart=0:2\0" \
 136         "console=ttyO2,115200n8\0" \
 137         "mpurate=auto\0" \
 138         "buddy=none\0" \
 139         "optargs=\0" \
 140         "camera=none\0" \
 141         "vram=12M\0" \
 142         "dvimode=640x480MR-16@60\0" \
 143         "defaultdisplay=dvi\0" \
 144         "mmcdev=0\0" \
 145         "mmcroot=/dev/mmcblk0p2 rw\0" \
 146         "mmcrootfstype=ext3 rootwait\0" \
 147         "nandroot=ubi0:rootfs ubi.mtd=4\0" \
 148         "nandrootfstype=ubifs\0" \
 149         "ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
 150         "ramrootfstype=ext2\0" \
 151         "mmcargs=setenv bootargs console=${console} " \
 152                 "${optargs} " \
 153                 "mpurate=${mpurate} " \
 154                 "buddy=${buddy} "\
 155                 "camera=${camera} "\
 156                 "vram=${vram} " \
 157                 "omapfb.mode=dvi:${dvimode} " \
 158                 "omapdss.def_disp=${defaultdisplay} " \
 159                 "root=${mmcroot} " \
 160                 "rootfstype=${mmcrootfstype}\0" \
 161         "nandargs=setenv bootargs console=${console} " \
 162                 "${optargs} " \
 163                 "mpurate=${mpurate} " \
 164                 "buddy=${buddy} "\
 165                 "camera=${camera} "\
 166                 "vram=${vram} " \
 167                 "omapfb.mode=dvi:${dvimode} " \
 168                 "omapdss.def_disp=${defaultdisplay} " \
 169                 "root=${nandroot} " \
 170                 "rootfstype=${nandrootfstype}\0" \
 171         "findfdt=" \
 172                 "if test $beaglerev = AxBx; then " \
 173                         "setenv fdtfile omap3-beagle.dtb; fi; " \
 174                 "if test $beaglerev = Cx; then " \
 175                         "setenv fdtfile omap3-beagle.dtb; fi; " \
 176                 "if test $beaglerev = C4; then " \
 177                         "setenv fdtfile omap3-beagle.dtb; fi; " \
 178                 "if test $beaglerev = xMAB; then " \
 179                         "setenv fdtfile omap3-beagle-xm-ab.dtb; fi; " \
 180                 "if test $beaglerev = xMC; then " \
 181                         "setenv fdtfile omap3-beagle-xm.dtb; fi; " \
 182                 "if test $fdtfile = undefined; then " \
 183                         "echo WARNING: Could not determine device tree to use; fi; \0" \
 184         "validatefdt=" \
 185                 "if test $beaglerev = xMAB; then " \
 186                         "if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile}; then " \
 187                                 "setenv fdtfile omap3-beagle-xm.dtb; " \
 188                         "fi; " \
 189                 "fi; \0" \
 190         "bootenv=uEnv.txt\0" \
 191         "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
 192         "importbootenv=echo Importing environment from mmc ...; " \
 193                 "env import -t -r $loadaddr $filesize\0" \
 194         "ramargs=setenv bootargs console=${console} " \
 195                 "${optargs} " \
 196                 "mpurate=${mpurate} " \
 197                 "buddy=${buddy} "\
 198                 "vram=${vram} " \
 199                 "omapfb.mode=dvi:${dvimode} " \
 200                 "omapdss.def_disp=${defaultdisplay} " \
 201                 "root=${ramroot} " \
 202                 "rootfstype=${ramrootfstype}\0" \
 203         "loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
 204         "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
 205         "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
 206         "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
 207                 "source ${loadaddr}\0" \
 208         "loadfdt=run validatefdt; load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
 209         "mmcboot=echo Booting from mmc ...; " \
 210                 "run mmcargs; " \
 211                 "bootm ${loadaddr}\0" \
 212         "mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
 213                 "run mmcargs; " \
 214                 "bootz ${loadaddr} - ${fdtaddr}\0" \
 215         "nandboot=echo Booting from nand ...; " \
 216                 "run nandargs; " \
 217                 "nand read ${loadaddr} 280000 400000; " \
 218                 "bootm ${loadaddr}\0" \
 219         "ramboot=echo Booting from ramdisk ...; " \
 220                 "run ramargs; " \
 221                 "bootm ${loadaddr}\0" \
 222         "userbutton=if gpio input 173; then run userbutton_xm; " \
 223                 "else run userbutton_nonxm; fi;\0" \
 224         "userbutton_xm=gpio input 4;\0" \
 225         "userbutton_nonxm=gpio input 7;\0"
 226 /* "run userbutton" will return 1 (false) if pressed and 0 (true) if not */
 227 #define CONFIG_BOOTCOMMAND \
 228         "run findfdt; " \
 229         "mmc dev ${mmcdev}; if mmc rescan; then " \
 230                 "if run userbutton; then " \
 231                         "setenv bootenv uEnv.txt;" \
 232                 "else " \
 233                         "setenv bootenv user.txt;" \
 234                 "fi;" \
 235                 "echo SD/MMC found on device ${mmcdev};" \
 236                 "if run loadbootenv; then " \
 237                         "echo Loaded environment from ${bootenv};" \
 238                         "run importbootenv;" \
 239                 "fi;" \
 240                 "if test -n $uenvcmd; then " \
 241                         "echo Running uenvcmd ...;" \
 242                         "run uenvcmd;" \
 243                 "fi;" \
 244                 "if run loadbootscript; then " \
 245                         "run bootscript; " \
 246                 "else " \
 247                         "if run loadimage; then " \
 248                                 "run mmcboot;" \
 249                         "fi;" \
 250                 "fi; " \
 251         "fi;" \
 252         "run nandboot;" \
 253         "setenv bootfile zImage;" \
 254         "if run loadimage; then " \
 255                 "run loadfdt;" \
 256                 "run mmcbootz; " \
 257         "fi; " \
 258
 259 /*
 260  * OMAP3 has 12 GP timers, they can be driven by the system clock
 261  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
 262  * This rate is divided by a local divisor.
 263  */
 264 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
 265
 266 /*-----------------------------------------------------------------------
 267  * FLASH and environment organization
 268  */
 269
 270 /* **** PISMO SUPPORT *** */
 271 #if defined(CONFIG_CMD_NAND)
 272 #define CONFIG_SYS_FLASH_BASE           NAND_BASE
 273 #endif
 274
 275 /* Monitor at start of flash */
 276 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_FLASH_BASE
 277 #define CONFIG_SYS_ONENAND_BASE         ONENAND_MAP
 278
 279 #define CONFIG_ENV_IS_IN_NAND           1
 280 #define CONFIG_ENV_SIZE                 (128 << 10)     /* 128 KiB */
 281 #define ONENAND_ENV_OFFSET              0x260000 /* environment starts here */
 282 #define SMNAND_ENV_OFFSET               0x260000 /* environment starts here */
 283
 284 #define CONFIG_SYS_ENV_SECT_SIZE        (128 << 10)     /* 128 KiB */
 285 #define CONFIG_ENV_OFFSET               SMNAND_ENV_OFFSET
 286 #define CONFIG_ENV_ADDR                 SMNAND_ENV_OFFSET
 287
 288 #define CONFIG_OMAP3_SPI
 289
 290 #define CONFIG_SYS_CACHELINE_SIZE       64
 291
 292 /* Defines for SPL */
 293 #define CONFIG_SPL_OMAP3_ID_NAND
 294
 295 /* NAND boot config */
 296 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT
 297 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 298 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 299 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
 300 #define CONFIG_SYS_NAND_OOBSIZE         64
 301 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128*1024)
 302 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
 303 #define CONFIG_SYS_NAND_ECCPOS          {2, 3, 4, 5, 6, 7, 8, 9,\
 304                                                 10, 11, 12, 13}
 305 #define CONFIG_SYS_NAND_ECCSIZE         512
 306 #define CONFIG_SYS_NAND_ECCBYTES        3
 307 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_HAM1_CODE_HW
 308 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 309 /* NAND: SPL falcon mode configs */
 310 #ifdef CONFIG_SPL_OS_BOOT
 311 #define CONFIG_CMD_SPL_NAND_OFS         0x240000
 312 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
 313 #define CONFIG_CMD_SPL_WRITE_SIZE       0x2000
 314 #endif
 315
 316 #endif /* __CONFIG_H */