include/configs/nitrogen6x.h

   1 /*
   2  * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
   3  *
   4  * Configuration settings for the Boundary Devices Nitrogen6X
   5  * and Freescale i.MX6Q Sabre Lite boards.
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #include "mx6_common.h"
  14
  15 #define CONFIG_MACH_TYPE        3769
  16
  17 /* Size of malloc() pool */
  18 #define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
  19
  20 #define CONFIG_BOARD_EARLY_INIT_F
  21 #define CONFIG_MISC_INIT_R
  22 #define CONFIG_MXC_GPIO
  23 #define CONFIG_CMD_GPIO
  24 #define CONFIG_CI_UDC
  25 #define CONFIG_USBD_HS
  26 #define CONFIG_USB_GADGET_DUALSPEED
  27 #define CONFIG_USB_ETHER
  28 #define CONFIG_USB_ETH_CDC
  29 #define CONFIG_NETCONSOLE
  30
  31 #define CONFIG_CMD_FUSE
  32 #ifdef CONFIG_CMD_FUSE
  33 #define CONFIG_MXC_OCOTP
  34 #endif
  35
  36 #define CONFIG_MXC_UART
  37 #define CONFIG_MXC_UART_BASE           UART2_BASE
  38
  39 #define CONFIG_CMD_SF
  40 #ifdef CONFIG_CMD_SF
  41 #define CONFIG_SPI_FLASH
  42 #define CONFIG_SPI_FLASH_SST
  43 #define CONFIG_MXC_SPI
  44 #define CONFIG_SF_DEFAULT_BUS  0
  45 #define CONFIG_SF_DEFAULT_CS   0
  46 #define CONFIG_SF_DEFAULT_SPEED 25000000
  47 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
  48 #endif
  49
  50 /* I2C Configs */
  51 #define CONFIG_CMD_I2C
  52 #define CONFIG_SYS_I2C
  53 #define CONFIG_SYS_I2C_MXC
  54 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  55 #define CONFIG_SYS_I2C_SPEED            100000
  56 #define CONFIG_I2C_EDID
  57
  58 /* MMC Configs */
  59 #define CONFIG_FSL_ESDHC
  60 #define CONFIG_FSL_USDHC
  61 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  62 #define CONFIG_SYS_FSL_USDHC_NUM       2
  63
  64 #define CONFIG_MMC
  65 #define CONFIG_CMD_MMC
  66 #define CONFIG_GENERIC_MMC
  67 #define CONFIG_BOUNCE_BUFFER
  68 #define CONFIG_CMD_EXT2
  69 #define CONFIG_CMD_EXT4
  70 #define CONFIG_CMD_EXT4_WRITE
  71 #define CONFIG_CMD_FAT
  72 #define CONFIG_DOS_PARTITION
  73
  74 #ifdef CONFIG_MX6Q
  75 #define CONFIG_CMD_SATA
  76 #endif
  77
  78 /*
  79  * SATA Configs
  80  */
  81 #ifdef CONFIG_CMD_SATA
  82 #define CONFIG_DWC_AHSATA
  83 #define CONFIG_SYS_SATA_MAX_DEVICE      1
  84 #define CONFIG_DWC_AHSATA_PORT_ID       0
  85 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
  86 #define CONFIG_LBA48
  87 #define CONFIG_LIBATA
  88 #endif
  89
  90 #define CONFIG_CMD_PING
  91 #define CONFIG_CMD_DHCP
  92 #define CONFIG_CMD_MII
  93 #define CONFIG_CMD_NET
  94 #define CONFIG_FEC_MXC
  95 #define CONFIG_MII
  96 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  97 #define CONFIG_FEC_XCV_TYPE             RGMII
  98 #define CONFIG_ETHPRIME                 "FEC"
  99 #define CONFIG_FEC_MXC_PHYADDR          6
 100 #define CONFIG_PHYLIB
 101 #define CONFIG_PHY_MICREL
 102 #define CONFIG_PHY_MICREL_KSZ9021
 103
 104 /* USB Configs */
 105 #define CONFIG_CMD_USB
 106 #define CONFIG_CMD_FAT
 107 #define CONFIG_USB_EHCI
 108 #define CONFIG_USB_EHCI_MX6
 109 #define CONFIG_USB_STORAGE
 110 #define CONFIG_USB_HOST_ETHER
 111 #define CONFIG_USB_ETHER_ASIX
 112 #define CONFIG_USB_ETHER_MCS7830
 113 #define CONFIG_USB_ETHER_SMSC95XX
 114 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 115 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
 116 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
 117 #define CONFIG_MXC_USB_FLAGS    0
 118 #define CONFIG_USB_KEYBOARD
 119 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
 120
 121 /* Miscellaneous commands */
 122 #define CONFIG_CMD_BMODE
 123 #define CONFIG_CMD_SETEXPR
 124
 125 /* Framebuffer and LCD */
 126 #define CONFIG_VIDEO
 127 #define CONFIG_VIDEO_IPUV3
 128 #define CONFIG_CFB_CONSOLE
 129 #define CONFIG_VGA_AS_SINGLE_DEVICE
 130 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 131 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
 132 #define CONFIG_VIDEO_BMP_RLE8
 133 #define CONFIG_SPLASH_SCREEN
 134 #define CONFIG_SPLASH_SCREEN_ALIGN
 135 #define CONFIG_VIDEO_BMP_GZIP
 136 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (6 * 1024 * 1024)
 137 #define CONFIG_BMP_16BPP
 138 #define CONFIG_IPUV3_CLK 260000000
 139 #define CONFIG_CMD_HDMIDETECT
 140 #define CONFIG_CONSOLE_MUX
 141 #define CONFIG_IMX_HDMI
 142 #define CONFIG_IMX_VIDEO_SKIP
 143
 144 /* allow to overwrite serial and ethaddr */
 145 #define CONFIG_ENV_OVERWRITE
 146 #define CONFIG_CONS_INDEX              1
 147 #define CONFIG_BAUDRATE                        115200
 148
 149 /* Command definition */
 150
 151 #define CONFIG_BOOTDELAY               1
 152
 153 #define CONFIG_PREBOOT                 ""
 154
 155 #define CONFIG_LOADADDR                        0x12000000
 156 #define CONFIG_SYS_TEXT_BASE           0x17800000
 157
 158 #ifdef CONFIG_CMD_SATA
 159 #define CONFIG_DRIVE_SATA "sata "
 160 #else
 161 #define CONFIG_DRIVE_SATA
 162 #endif
 163
 164 #ifdef CONFIG_CMD_MMC
 165 #define CONFIG_DRIVE_MMC "mmc "
 166 #else
 167 #define CONFIG_DRIVE_MMC
 168 #endif
 169
 170 #ifdef CONFIG_USB_STORAGE
 171 #define CONFIG_DRIVE_USB "usb "
 172 #else
 173 #define CONFIG_DRIVE_USB
 174 #endif
 175
 176 #define CONFIG_DRIVE_TYPES CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC CONFIG_DRIVE_USB
 177 #define CONFIG_UMSDEVS CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC
 178
 179 #if defined(CONFIG_SABRELITE)
 180 #define CONFIG_EXTRA_ENV_SETTINGS \
 181         "script=boot.scr\0" \
 182         "uimage=uImage\0" \
 183         "console=ttymxc1\0" \
 184         "fdt_high=0xffffffff\0" \
 185         "initrd_high=0xffffffff\0" \
 186         "fdt_file=imx6q-sabrelite.dtb\0" \
 187         "fdt_addr=0x18000000\0" \
 188         "boot_fdt=try\0" \
 189         "ip_dyn=yes\0" \
 190         "mmcdevs=0 1\0" \
 191         "mmcpart=1\0" \
 192         "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
 193         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 194                 "root=${mmcroot}\0" \
 195         "loadbootscript=" \
 196                 "load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 197         "bootscript=echo Running bootscript from mmc ...; " \
 198                 "source\0" \
 199         "loaduimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
 200         "loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 201         "mmcboot=echo Booting from mmc ...; " \
 202                 "run mmcargs; " \
 203                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 204                         "if run loadfdt; then " \
 205                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 206                         "else " \
 207                                 "if test ${boot_fdt} = try; then " \
 208                                         "bootm; " \
 209                                 "else " \
 210                                         "echo WARN: Cannot load the DT; " \
 211                                 "fi; " \
 212                         "fi; " \
 213                 "else " \
 214                         "bootm; " \
 215                 "fi;\0" \
 216         "netargs=setenv bootargs console=${console},${baudrate} " \
 217                 "root=/dev/nfs " \
 218         "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 219                 "netboot=echo Booting from net ...; " \
 220                 "run netargs; " \
 221                 "if test ${ip_dyn} = yes; then " \
 222                         "setenv get_cmd dhcp; " \
 223                 "else " \
 224                         "setenv get_cmd tftp; " \
 225                 "fi; " \
 226                 "${get_cmd} ${uimage}; " \
 227                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 228                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 229                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 230                         "else " \
 231                                 "if test ${boot_fdt} = try; then " \
 232                                         "bootm; " \
 233                                 "else " \
 234                                         "echo WARN: Cannot load the DT; " \
 235                                 "fi; " \
 236                         "fi; " \
 237                 "else " \
 238                         "bootm; " \
 239                 "fi;\0"
 240
 241 #define CONFIG_BOOTCOMMAND \
 242         "for mmcdev in ${mmcdevs}; do " \
 243                 "mmc dev ${mmcdev}; " \
 244                 "if mmc rescan; then " \
 245                         "if run loadbootscript; then " \
 246                                 "run bootscript; " \
 247                         "else " \
 248                                 "if run loaduimage; then " \
 249                                         "run mmcboot; " \
 250                                 "fi; " \
 251                         "fi; " \
 252                 "fi; " \
 253         "done; " \
 254         "run netboot; "
 255 #else
 256 #define CONFIG_EXTRA_ENV_SETTINGS \
 257         "bootdevs=" CONFIG_DRIVE_TYPES "\0" \
 258         "umsdevs=" CONFIG_UMSDEVS "\0" \
 259         "console=ttymxc1\0" \
 260         "clearenv=if sf probe || sf probe || sf probe 1 ; then " \
 261                 "sf erase 0xc0000 0x2000 && " \
 262                 "echo restored environment to factory default ; fi\0" \
 263         "bootcmd=for dtype in ${bootdevs}" \
 264                 "; do " \
 265                         "if itest.s \"xusb\" == \"x${dtype}\" ; then " \
 266                                 "usb start ;" \
 267                         "fi; " \
 268                         "for disk in 0 1 ; do ${dtype} dev ${disk} ;" \
 269                                 "load " \
 270                                         "${dtype} ${disk}:1 " \
 271                                         "10008000 " \
 272                                         "/6x_bootscript" \
 273                                         "&& source 10008000 ; " \
 274                         "done ; " \
 275                 "done; " \
 276                 "setenv stdout serial,vga ; " \
 277                 "echo ; echo 6x_bootscript not found ; " \
 278                 "echo ; echo serial console at 115200, 8N1 ; echo ; " \
 279                 "echo details at http://boundarydevices.com/6q_bootscript ; " \
 280                 "setenv stdout serial;" \
 281                 "setenv stdin serial,usbkbd;" \
 282                 "for dtype in ${umsdevs} ; do " \
 283                         "if itest.s sata == ${dtype}; then " \
 284                                 "initcmd='sata init' ;" \
 285                         "else " \
 286                                 "initcmd='mmc rescan' ;" \
 287                         "fi; " \
 288                         "for disk in 0 1 ; do " \
 289                                 "if $initcmd && $dtype dev $disk ; then " \
 290                                         "setenv stdout serial,vga; " \
 291                                         "echo expose ${dtype} ${disk} " \
 292                                                 "over USB; " \
 293                                         "ums 0 $dtype $disk ;" \
 294                                 "fi; " \
 295                 "       done; " \
 296                 "done ;" \
 297                 "setenv stdout serial,vga; " \
 298                 "echo no block devices found;" \
 299                 "\0" \
 300         "initrd_high=0xffffffff\0" \
 301         "upgradeu=for dtype in ${bootdevs}" \
 302                 "; do " \
 303                 "for disk in 0 1 ; do ${dtype} dev ${disk} ;" \
 304                         "load ${dtype} ${disk}:1 10008000 " \
 305                                 "/6x_upgrade " \
 306                                 "&& source 10008000 ; " \
 307                 "done ; " \
 308         "done\0" \
 309
 310 #endif
 311 /* Miscellaneous configurable options */
 312 #define CONFIG_SYS_LONGHELP
 313 #define CONFIG_SYS_HUSH_PARSER
 314 #define CONFIG_SYS_PROMPT              "U-Boot > "
 315 #define CONFIG_AUTO_COMPLETE
 316 #define CONFIG_SYS_CBSIZE              1024
 317 #define CONFIG_SYS_MAXARGS             48
 318 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 319
 320 #define CONFIG_SYS_MEMTEST_START       0x10000000
 321 #define CONFIG_SYS_MEMTEST_END         0x10010000
 322 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 323
 324 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 325
 326 #define CONFIG_CMDLINE_EDITING
 327
 328 /* Physical Memory Map */
 329 #define CONFIG_NR_DRAM_BANKS           1
 330 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 331
 332 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 333 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 334 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 335
 336 #define CONFIG_SYS_INIT_SP_OFFSET \
 337         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 338 #define CONFIG_SYS_INIT_SP_ADDR \
 339         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 340
 341 /* Environment organization */
 342 #define CONFIG_ENV_SIZE                 (8 * 1024)
 343
 344 #if defined(CONFIG_SABRELITE)
 345 #define CONFIG_ENV_IS_IN_MMC
 346 #else
 347 #define CONFIG_ENV_IS_IN_SPI_FLASH
 348 #endif
 349
 350 #if defined(CONFIG_ENV_IS_IN_MMC)
 351 #define CONFIG_ENV_OFFSET               (6 * 64 * 1024)
 352 #define CONFIG_SYS_MMC_ENV_DEV          0
 353 #elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
 354 #define CONFIG_ENV_OFFSET               (768 * 1024)
 355 #define CONFIG_ENV_SECT_SIZE            (8 * 1024)
 356 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 357 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 358 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 359 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 360 #endif
 361
 362 #define CONFIG_OF_LIBFDT
 363 #define CONFIG_CMD_BOOTZ
 364
 365 #ifndef CONFIG_SYS_DCACHE_OFF
 366 #define CONFIG_CMD_CACHE
 367 #endif
 368
 369 #define CONFIG_CMD_BMP
 370
 371 #define CONFIG_CMD_TIME
 372 #define CONFIG_CMD_MEMTEST
 373 #define CONFIG_SYS_ALT_MEMTEST
 374
 375 #define CONFIG_CMD_BOOTZ
 376 #define CONFIG_SUPPORT_RAW_INITRD
 377 #define CONFIG_CMD_FS_GENERIC
 378
 379 /*
 380  * PCI express
 381  */
 382 #ifdef CONFIG_CMD_PCI
 383 #define CONFIG_PCI
 384 #define CONFIG_PCI_PNP
 385 #define CONFIG_PCI_SCAN_SHOW
 386 #define CONFIG_PCIE_IMX
 387 #endif
 388
 389 #define CONFIG_CMD_ELF
 390
 391 #define CONFIG_USB_GADGET
 392 #define CONFIG_CMD_USB_MASS_STORAGE
 393 #define CONFIG_USB_GADGET_MASS_STORAGE
 394 #define CONFIG_USBDOWNLOAD_GADGET
 395 #define CONFIG_USB_GADGET_VBUS_DRAW     2
 396
 397 /* Netchip IDs */
 398 #define CONFIG_G_DNL_VENDOR_NUM 0x0525
 399 #define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5
 400 #define CONFIG_G_DNL_MANUFACTURER "Boundary"
 401
 402 #define CONFIG_CMD_FASTBOOT
 403 #define CONFIG_ANDROID_BOOT_IMAGE
 404 #define CONFIG_USB_FASTBOOT_BUF_ADDR   CONFIG_SYS_LOAD_ADDR
 405 #define CONFIG_USB_FASTBOOT_BUF_SIZE   0x07000000
 406
 407 #endif         /* __CONFIG_H */