Kconfig: USB: Migrate CONFIG_USB_EHCI_HCD users to Kconfig
[platform/kernel/u-boot.git] / include / configs / nitrogen6x.h
1 /*
2  * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
3  *
4  * Configuration settings for the Boundary Devices Nitrogen6X
5  * and Freescale i.MX6Q Sabre Lite boards.
6  *
7  * SPDX-License-Identifier:     GPL-2.0+
8  */
9
10 #ifndef __CONFIG_H
11 #define __CONFIG_H
12
13 #include "mx6_common.h"
14
15 #define CONFIG_MACH_TYPE        3769
16
17 /* Size of malloc() pool */
18 #define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
19
20 #define CONFIG_MISC_INIT_R
21 #define CONFIG_USBD_HS
22 #define CONFIG_USB_ETHER
23 #define CONFIG_USB_ETH_CDC
24 #define CONFIG_NETCONSOLE
25
26 #define CONFIG_MXC_UART
27 #define CONFIG_MXC_UART_BASE           UART2_BASE
28
29 #ifdef CONFIG_CMD_SF
30 #define CONFIG_MXC_SPI
31 #define CONFIG_SF_DEFAULT_BUS  0
32 #define CONFIG_SF_DEFAULT_CS   0
33 #define CONFIG_SF_DEFAULT_SPEED 25000000
34 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
35 #endif
36
37 /* I2C Configs */
38 #define CONFIG_SYS_I2C
39 #define CONFIG_SYS_I2C_MXC
40 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
41 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
42 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
43 #define CONFIG_SYS_I2C_SPEED            100000
44 #define CONFIG_I2C_EDID
45
46 /* MMC Configs */
47 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
48 #define CONFIG_SYS_FSL_USDHC_NUM       2
49
50 #ifdef CONFIG_MX6Q
51 #define CONFIG_CMD_SATA
52 #endif
53
54 /*
55  * SATA Configs
56  */
57 #ifdef CONFIG_CMD_SATA
58 #define CONFIG_DWC_AHSATA
59 #define CONFIG_SYS_SATA_MAX_DEVICE      1
60 #define CONFIG_DWC_AHSATA_PORT_ID       0
61 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
62 #define CONFIG_LBA48
63 #define CONFIG_LIBATA
64 #endif
65
66 #define CONFIG_FEC_MXC
67 #define CONFIG_MII
68 #define IMX_FEC_BASE                    ENET_BASE_ADDR
69 #define CONFIG_FEC_XCV_TYPE             RGMII
70 #define CONFIG_ETHPRIME                 "FEC"
71 #define CONFIG_FEC_MXC_PHYADDR          6
72 #define CONFIG_PHYLIB
73 #define CONFIG_PHY_MICREL
74 #define CONFIG_PHY_MICREL_KSZ9021
75
76 /* USB Configs */
77 #define CONFIG_USB_EHCI_MX6
78 #define CONFIG_USB_HOST_ETHER
79 #define CONFIG_USB_ETHER_ASIX
80 #define CONFIG_USB_ETHER_MCS7830
81 #define CONFIG_USB_ETHER_SMSC95XX
82 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
83 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
84 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
85 #define CONFIG_MXC_USB_FLAGS    0
86 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
87
88 /* Framebuffer and LCD */
89 #define CONFIG_VIDEO_IPUV3
90 #define CONFIG_VIDEO_BMP_RLE8
91 #define CONFIG_SPLASH_SCREEN
92 #define CONFIG_SPLASH_SCREEN_ALIGN
93 #define CONFIG_VIDEO_BMP_GZIP
94 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (6 * 1024 * 1024)
95 #define CONFIG_BMP_16BPP
96 #define CONFIG_IPUV3_CLK 260000000
97 #define CONFIG_CMD_HDMIDETECT
98 #define CONFIG_IMX_HDMI
99 #define CONFIG_IMX_VIDEO_SKIP
100
101 #define CONFIG_PREBOOT                 ""
102
103 #ifdef CONFIG_CMD_SATA
104 #define CONFIG_DRIVE_SATA "sata "
105 #else
106 #define CONFIG_DRIVE_SATA
107 #endif
108
109 #ifdef CONFIG_CMD_MMC
110 #define CONFIG_DRIVE_MMC "mmc "
111 #else
112 #define CONFIG_DRIVE_MMC
113 #endif
114
115 #ifdef CONFIG_USB_STORAGE
116 #define CONFIG_DRIVE_USB "usb "
117 #else
118 #define CONFIG_DRIVE_USB
119 #endif
120
121 #define CONFIG_DRIVE_TYPES CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC CONFIG_DRIVE_USB
122 #define CONFIG_UMSDEVS CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC
123
124 #if defined(CONFIG_SABRELITE)
125 #define CONFIG_EXTRA_ENV_SETTINGS \
126         "script=boot.scr\0" \
127         "uimage=uImage\0" \
128         "console=ttymxc1\0" \
129         "fdt_high=0xffffffff\0" \
130         "initrd_high=0xffffffff\0" \
131         "fdt_file=imx6q-sabrelite.dtb\0" \
132         "fdt_addr=0x18000000\0" \
133         "boot_fdt=try\0" \
134         "ip_dyn=yes\0" \
135         "usb_pgood_delay=2000\0" \
136         "mmcdevs=0 1\0" \
137         "mmcpart=1\0" \
138         "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
139         "mmcargs=setenv bootargs console=${console},${baudrate} " \
140                 "root=${mmcroot}\0" \
141         "loadbootscript=" \
142                 "load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
143         "bootscript=echo Running bootscript from mmc ...; " \
144                 "source\0" \
145         "loaduimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
146         "loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
147         "mmcboot=echo Booting from mmc ...; " \
148                 "run mmcargs; " \
149                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
150                         "if run loadfdt; then " \
151                                 "bootm ${loadaddr} - ${fdt_addr}; " \
152                         "else " \
153                                 "if test ${boot_fdt} = try; then " \
154                                         "bootm; " \
155                                 "else " \
156                                         "echo WARN: Cannot load the DT; " \
157                                 "fi; " \
158                         "fi; " \
159                 "else " \
160                         "bootm; " \
161                 "fi;\0" \
162         "netargs=setenv bootargs console=${console},${baudrate} " \
163                 "root=/dev/nfs " \
164         "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
165                 "netboot=echo Booting from net ...; " \
166                 "run netargs; " \
167                 "if test ${ip_dyn} = yes; then " \
168                         "setenv get_cmd dhcp; " \
169                 "else " \
170                         "setenv get_cmd tftp; " \
171                 "fi; " \
172                 "${get_cmd} ${uimage}; " \
173                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
174                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
175                                 "bootm ${loadaddr} - ${fdt_addr}; " \
176                         "else " \
177                                 "if test ${boot_fdt} = try; then " \
178                                         "bootm; " \
179                                 "else " \
180                                         "echo WARN: Cannot load the DT; " \
181                                 "fi; " \
182                         "fi; " \
183                 "else " \
184                         "bootm; " \
185                 "fi;\0"
186
187 #define CONFIG_BOOTCOMMAND \
188         "for mmcdev in ${mmcdevs}; do " \
189                 "mmc dev ${mmcdev}; " \
190                 "if mmc rescan; then " \
191                         "if run loadbootscript; then " \
192                                 "run bootscript; " \
193                         "else " \
194                                 "if run loaduimage; then " \
195                                         "run mmcboot; " \
196                                 "fi; " \
197                         "fi; " \
198                 "fi; " \
199         "done; " \
200         "run netboot; "
201 #else
202 #define CONFIG_EXTRA_ENV_SETTINGS \
203         "bootdevs=" CONFIG_DRIVE_TYPES "\0" \
204         "umsdevs=" CONFIG_UMSDEVS "\0" \
205         "usb_pgood_delay=2000\0" \
206         "console=ttymxc1\0" \
207         "clearenv=if sf probe || sf probe || sf probe 1 ; then " \
208                 "sf erase 0xc0000 0x2000 && " \
209                 "echo restored environment to factory default ; fi\0" \
210         "bootcmd=for dtype in ${bootdevs}" \
211                 "; do " \
212                         "if itest.s \"xusb\" == \"x${dtype}\" ; then " \
213                                 "usb start ;" \
214                         "fi; " \
215                         "for disk in 0 1 ; do ${dtype} dev ${disk} ;" \
216                                 "load " \
217                                         "${dtype} ${disk}:1 " \
218                                         "10008000 " \
219                                         "/6x_bootscript" \
220                                         "&& source 10008000 ; " \
221                         "done ; " \
222                 "done; " \
223                 "setenv stdout serial,vga ; " \
224                 "echo ; echo 6x_bootscript not found ; " \
225                 "echo ; echo serial console at 115200, 8N1 ; echo ; " \
226                 "echo details at http://boundarydevices.com/6q_bootscript ; " \
227                 "setenv stdout serial;" \
228                 "setenv stdin serial,usbkbd;" \
229                 "for dtype in ${umsdevs} ; do " \
230                         "if itest.s sata == ${dtype}; then " \
231                                 "initcmd='sata init' ;" \
232                         "else " \
233                                 "initcmd='mmc rescan' ;" \
234                         "fi; " \
235                         "for disk in 0 1 ; do " \
236                                 "if $initcmd && $dtype dev $disk ; then " \
237                                         "setenv stdout serial,vga; " \
238                                         "echo expose ${dtype} ${disk} " \
239                                                 "over USB; " \
240                                         "ums 0 $dtype $disk ;" \
241                                 "fi; " \
242                 "       done; " \
243                 "done ;" \
244                 "setenv stdout serial,vga; " \
245                 "echo no block devices found;" \
246                 "\0" \
247         "initrd_high=0xffffffff\0" \
248         "upgradeu=for dtype in ${bootdevs}" \
249                 "; do " \
250                 "for disk in 0 1 ; do ${dtype} dev ${disk} ;" \
251                         "load ${dtype} ${disk}:1 10008000 " \
252                                 "/6x_upgrade " \
253                                 "&& source 10008000 ; " \
254                 "done ; " \
255         "done\0" \
256
257 #endif
258 /* Miscellaneous configurable options */
259 #define CONFIG_SYS_MEMTEST_START       0x10000000
260 #define CONFIG_SYS_MEMTEST_END         0x10010000
261 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
262
263 /* Physical Memory Map */
264 #define CONFIG_NR_DRAM_BANKS           1
265 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
266
267 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
268 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
269 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
270
271 #define CONFIG_SYS_INIT_SP_OFFSET \
272         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
273 #define CONFIG_SYS_INIT_SP_ADDR \
274         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
275
276 /* Environment organization */
277 #define CONFIG_ENV_SIZE                 (8 * 1024)
278
279 #if defined(CONFIG_SABRELITE)
280 #define CONFIG_ENV_IS_IN_MMC
281 #else
282 #define CONFIG_ENV_IS_IN_SPI_FLASH
283 #endif
284
285 #if defined(CONFIG_ENV_IS_IN_MMC)
286 #define CONFIG_ENV_OFFSET               (6 * 64 * 1024)
287 #define CONFIG_SYS_MMC_ENV_DEV          0
288 #elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
289 #define CONFIG_ENV_OFFSET               (768 * 1024)
290 #define CONFIG_ENV_SECT_SIZE            (8 * 1024)
291 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
292 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
293 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
294 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
295 #endif
296
297 #define CONFIG_SYS_ALT_MEMTEST
298
299 /*
300  * PCI express
301  */
302 #ifdef CONFIG_CMD_PCI
303 #define CONFIG_PCI_SCAN_SHOW
304 #define CONFIG_PCIE_IMX
305 #endif
306
307 #define CONFIG_USB_FUNCTION_MASS_STORAGE
308
309 #define CONFIG_USB_FUNCTION_FASTBOOT
310 #define CONFIG_CMD_FASTBOOT
311 #define CONFIG_ANDROID_BOOT_IMAGE
312 #define CONFIG_FASTBOOT_BUF_ADDR   CONFIG_SYS_LOAD_ADDR
313 #define CONFIG_FASTBOOT_BUF_SIZE   0x07000000
314
315 #endif         /* __CONFIG_H */