include/configs/mx7dsabresd.h

   1 /*
   2  * Copyright (C) 2015 Freescale Semiconductor, Inc.
   3  *
   4  * Configuration settings for the Freescale i.MX7D SABRESD board.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __MX7D_SABRESD_CONFIG_H
  10 #define __MX7D_SABRESD_CONFIG_H
  11
  12 #include "mx7_common.h"
  13
  14 #define CONFIG_DBG_MONITOR
  15 #define PHYS_SDRAM_SIZE                 SZ_1G
  16
  17 #define CONFIG_MXC_UART_BASE            UART1_IPS_BASE_ADDR
  18
  19 /* Size of malloc() pool */
  20 #define CONFIG_SYS_MALLOC_LEN           (32 * SZ_1M)
  21
  22 #define CONFIG_BOARD_EARLY_INIT_F
  23 #define CONFIG_BOARD_LATE_INIT
  24
  25 /* Uncomment to enable secure boot support */
  26 /* #define CONFIG_SECURE_BOOT */
  27 #define CONFIG_CSF_SIZE                 0x4000
  28
  29 /* Network */
  30 #define CONFIG_CMD_MII
  31 #define CONFIG_FEC_MXC
  32 #define CONFIG_MII
  33 #define CONFIG_FEC_XCV_TYPE             RGMII
  34 #define CONFIG_ETHPRIME                 "FEC"
  35 #define CONFIG_FEC_MXC_PHYADDR          0
  36
  37 #define CONFIG_PHYLIB
  38 #define CONFIG_PHY_BROADCOM
  39 /* ENET1 */
  40 #define IMX_FEC_BASE                    ENET_IPS_BASE_ADDR
  41
  42 /* MMC Config*/
  43 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  44
  45 /* PMIC */
  46 #define CONFIG_POWER
  47 #define CONFIG_POWER_I2C
  48 #define CONFIG_POWER_PFUZE3000
  49 #define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08
  50
  51 #undef CONFIG_BOOTM_NETBSD
  52 #undef CONFIG_BOOTM_PLAN9
  53 #undef CONFIG_BOOTM_RTEMS
  54
  55 /* I2C configs */
  56 #define CONFIG_SYS_I2C
  57 #define CONFIG_SYS_I2C_MXC
  58 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  59 #define CONFIG_SYS_I2C_SPEED            100000
  60
  61 #define CONFIG_SUPPORT_EMMC_BOOT        /* eMMC specific */
  62 #define CONFIG_SYS_MMC_IMG_LOAD_PART    1
  63
  64 #ifdef CONFIG_IMX_BOOTAUX
  65 /* Set to QSPI1 A flash at default */
  66 #define CONFIG_SYS_AUXCORE_BOOTDATA 0x60000000
  67
  68 #define UPDATE_M4_ENV \
  69         "m4image=m4_qspi.bin\0" \
  70         "loadm4image=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4image}\0" \
  71         "update_m4_from_sd=" \
  72                 "if sf probe 0:0; then " \
  73                         "if run loadm4image; then " \
  74                                 "setexpr fw_sz ${filesize} + 0xffff; " \
  75                                 "setexpr fw_sz ${fw_sz} / 0x10000; "    \
  76                                 "setexpr fw_sz ${fw_sz} * 0x10000; "    \
  77                                 "sf erase 0x0 ${fw_sz}; " \
  78                                 "sf write ${loadaddr} 0x0 ${filesize}; " \
  79                         "fi; " \
  80                 "fi\0" \
  81         "m4boot=sf probe 0:0; bootaux "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)"\0"
  82 #else
  83 #define UPDATE_M4_ENV ""
  84 #endif
  85
  86 #define CONFIG_MFG_ENV_SETTINGS \
  87         "mfgtool_args=setenv bootargs console=${console},${baudrate} " \
  88                 "rdinit=/linuxrc " \
  89                 "g_mass_storage.stall=0 g_mass_storage.removable=1 " \
  90                 "g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
  91                 "g_mass_storage.iSerialNumber=\"\" "\
  92                 "clk_ignore_unused "\
  93                 "\0" \
  94         "initrd_addr=0x83800000\0" \
  95         "initrd_high=0xffffffff\0" \
  96         "bootcmd_mfg=run mfgtool_args;bootz ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \
  97
  98 #define CONFIG_DFU_ENV_SETTINGS \
  99         "dfu_alt_info=image raw 0 0x800000;"\
 100                 "u-boot raw 0 0x4000;"\
 101                 "bootimg part 0 1;"\
 102                 "rootfs part 0 2\0" \
 103
 104 #define CONFIG_EXTRA_ENV_SETTINGS \
 105         UPDATE_M4_ENV \
 106         CONFIG_MFG_ENV_SETTINGS \
 107         CONFIG_DFU_ENV_SETTINGS \
 108         "script=boot.scr\0" \
 109         "image=zImage\0" \
 110         "console=ttymxc0\0" \
 111         "fdt_high=0xffffffff\0" \
 112         "initrd_high=0xffffffff\0" \
 113         "fdt_file=imx7d-sdb.dtb\0" \
 114         "fdt_addr=0x83000000\0" \
 115         "boot_fdt=try\0" \
 116         "ip_dyn=yes\0" \
 117         "videomode=video=ctfb:x:480,y:272,depth:24,pclk:108695,le:8,ri:4,up:2,lo:4,hs:41,vs:10,sync:0,vmode:0\0" \
 118         "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
 119         "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
 120         "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 121         "mmcautodetect=yes\0" \
 122         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 123                 "root=${mmcroot}\0" \
 124         "loadbootscript=" \
 125                 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 126         "bootscript=echo Running bootscript from mmc ...; " \
 127                 "source\0" \
 128         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 129         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 130         "mmcboot=echo Booting from mmc ...; " \
 131                 "run mmcargs; " \
 132                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 133                         "if run loadfdt; then " \
 134                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 135                         "else " \
 136                                 "if test ${boot_fdt} = try; then " \
 137                                         "bootz; " \
 138                                 "else " \
 139                                         "echo WARN: Cannot load the DT; " \
 140                                 "fi; " \
 141                         "fi; " \
 142                 "else " \
 143                         "bootz; " \
 144                 "fi;\0" \
 145         "netargs=setenv bootargs console=${console},${baudrate} " \
 146                 "root=/dev/nfs " \
 147         "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 148                 "netboot=echo Booting from net ...; " \
 149                 "run netargs; " \
 150                 "if test ${ip_dyn} = yes; then " \
 151                         "setenv get_cmd dhcp; " \
 152                 "else " \
 153                         "setenv get_cmd tftp; " \
 154                 "fi; " \
 155                 "${get_cmd} ${image}; " \
 156                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 157                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 158                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 159                         "else " \
 160                                 "if test ${boot_fdt} = try; then " \
 161                                         "bootz; " \
 162                                 "else " \
 163                                         "echo WARN: Cannot load the DT; " \
 164                                 "fi; " \
 165                         "fi; " \
 166                 "else " \
 167                         "bootz; " \
 168                 "fi;\0"
 169
 170 #define CONFIG_BOOTCOMMAND \
 171            "mmc dev ${mmcdev};" \
 172            "mmc dev ${mmcdev}; if mmc rescan; then " \
 173                    "if run loadbootscript; then " \
 174                            "run bootscript; " \
 175                    "else " \
 176                            "if run loadimage; then " \
 177                                    "run mmcboot; " \
 178                            "else run netboot; " \
 179                            "fi; " \
 180                    "fi; " \
 181            "else run netboot; fi"
 182
 183 #define CONFIG_SYS_MEMTEST_START        0x80000000
 184 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_MEMTEST_START + 0x20000000)
 185
 186 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 187 #define CONFIG_SYS_HZ                   1000
 188
 189 #define CONFIG_STACKSIZE                SZ_128K
 190
 191 /* Physical Memory Map */
 192 #define CONFIG_NR_DRAM_BANKS            1
 193 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 194
 195 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 196 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 197 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 198
 199 #define CONFIG_SYS_INIT_SP_OFFSET \
 200         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 201 #define CONFIG_SYS_INIT_SP_ADDR \
 202         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 203
 204 /* FLASH and environment organization */
 205 #define CONFIG_SYS_NO_FLASH
 206 #define CONFIG_ENV_SIZE                 SZ_8K
 207 #define CONFIG_ENV_IS_IN_MMC
 208
 209 /*
 210  * If want to use nand, define CONFIG_NAND_MXS and rework board
 211  * to support nand, since emmc has pin conflicts with nand
 212  */
 213 #ifdef CONFIG_NAND_MXS
 214 #define CONFIG_CMD_NAND
 215 #define CONFIG_CMD_NAND_TRIMFFS
 216
 217 /* NAND stuff */
 218 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 219 #define CONFIG_SYS_NAND_BASE            0x40000000
 220 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 221 #define CONFIG_SYS_NAND_ONFI_DETECTION
 222
 223 /* DMA stuff, needed for GPMI/MXS NAND support */
 224 #define CONFIG_APBH_DMA
 225 #define CONFIG_APBH_DMA_BURST
 226 #define CONFIG_APBH_DMA_BURST8
 227 #endif
 228
 229 #define CONFIG_ENV_OFFSET               (8 * SZ_64K)
 230 #ifdef CONFIG_NAND_MXS
 231 #define CONFIG_SYS_FSL_USDHC_NUM        1
 232 #else
 233 #define CONFIG_SYS_FSL_USDHC_NUM        2
 234 #endif
 235
 236 #define CONFIG_SYS_MMC_ENV_DEV          0   /* USDHC1 */
 237 #define CONFIG_SYS_MMC_ENV_PART         0       /* user area */
 238 #define CONFIG_MMCROOT                  "/dev/mmcblk0p2"  /* USDHC1 */
 239
 240 /* USB Configs */
 241 #define CONFIG_USB_EHCI
 242 #define CONFIG_USB_EHCI_MX7
 243 #define CONFIG_USB_STORAGE
 244 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 245 #define CONFIG_USB_HOST_ETHER
 246 #define CONFIG_USB_ETHER_ASIX
 247 #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
 248 #define CONFIG_MXC_USB_FLAGS   0
 249 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 250
 251 #define CONFIG_IMX_THERMAL
 252
 253 #define CONFIG_USBD_HS
 254
 255 #define CONFIG_CMD_USB_MASS_STORAGE
 256 #define CONFIG_USB_FUNCTION_MASS_STORAGE
 257
 258 /* USB Device Firmware Update support */
 259 #define CONFIG_CMD_DFU
 260 #define CONFIG_USB_FUNCTION_DFU
 261 #define CONFIG_DFU_MMC
 262 #define CONFIG_DFU_RAM
 263
 264 #define CONFIG_VIDEO
 265 #ifdef CONFIG_VIDEO
 266 #define CONFIG_CFB_CONSOLE
 267 #define CONFIG_VIDEO_MXS
 268 #define CONFIG_VIDEO_LOGO
 269 #define CONFIG_VIDEO_SW_CURSOR
 270 #define CONFIG_VGA_AS_SINGLE_DEVICE
 271 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 272 #define CONFIG_SPLASH_SCREEN
 273 #define CONFIG_SPLASH_SCREEN_ALIGN
 274 #define CONFIG_CMD_BMP
 275 #define CONFIG_BMP_16BPP
 276 #define CONFIG_VIDEO_BMP_RLE8
 277 #define CONFIG_VIDEO_BMP_LOGO
 278 #endif
 279
 280 #ifdef CONFIG_FSL_QSPI
 281 #define CONFIG_SPI_FLASH
 282 #define CONFIG_SPI_FLASH_MACRONIX
 283 #define CONFIG_SPI_FLASH_BAR
 284 #define CONFIG_SF_DEFAULT_BUS           0
 285 #define CONFIG_SF_DEFAULT_CS            0
 286 #define CONFIG_SF_DEFAULT_SPEED         40000000
 287 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
 288 #define FSL_QSPI_FLASH_NUM              1
 289 #define FSL_QSPI_FLASH_SIZE             SZ_64M
 290 #define QSPI0_BASE_ADDR                 QSPI1_IPS_BASE_ADDR
 291 #define QSPI0_AMBA_BASE                 QSPI0_ARB_BASE_ADDR
 292 #endif
 293
 294 #endif  /* __CONFIG_H */