include/configs/mx7dsabresd.h

   1 /*
   2  * Copyright (C) 2015 Freescale Semiconductor, Inc.
   3  *
   4  * Configuration settings for the Freescale i.MX7D SABRESD board.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __MX7D_SABRESD_CONFIG_H
  10 #define __MX7D_SABRESD_CONFIG_H
  11
  12 #include "mx7_common.h"
  13
  14 #define CONFIG_DBG_MONITOR
  15 #define PHYS_SDRAM_SIZE                 SZ_1G
  16
  17 #define CONFIG_MXC_UART_BASE            UART1_IPS_BASE_ADDR
  18
  19 #define CONFIG_BOARD_EARLY_INIT_F
  20 #define CONFIG_BOARD_LATE_INIT
  21
  22 /* Uncomment to enable secure boot support */
  23 /* #define CONFIG_SECURE_BOOT */
  24 #define CONFIG_CSF_SIZE                 0x4000
  25
  26 /* Network */
  27 #define CONFIG_CMD_MII
  28 #define CONFIG_FEC_MXC
  29 #define CONFIG_MII
  30 #define CONFIG_FEC_XCV_TYPE             RGMII
  31 #define CONFIG_ETHPRIME                 "FEC"
  32 #define CONFIG_FEC_MXC_PHYADDR          0
  33
  34 #define CONFIG_PHYLIB
  35 #define CONFIG_PHY_BROADCOM
  36 /* ENET1 */
  37 #define IMX_FEC_BASE                    ENET_IPS_BASE_ADDR
  38
  39 /* MMC Config*/
  40 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  41
  42 /* PMIC */
  43 #define CONFIG_POWER
  44 #define CONFIG_POWER_I2C
  45 #define CONFIG_POWER_PFUZE3000
  46 #define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08
  47
  48 #undef CONFIG_BOOTM_NETBSD
  49 #undef CONFIG_BOOTM_PLAN9
  50 #undef CONFIG_BOOTM_RTEMS
  51
  52 #undef CONFIG_CMD_EXPORTENV
  53 #undef CONFIG_CMD_IMPORTENV
  54
  55 /* I2C configs */
  56 #define CONFIG_CMD_I2C
  57 #define CONFIG_SYS_I2C
  58 #define CONFIG_SYS_I2C_MXC
  59 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  60 #define CONFIG_SYS_I2C_SPEED            100000
  61
  62 #define CONFIG_SUPPORT_EMMC_BOOT        /* eMMC specific */
  63 #define CONFIG_SYS_MMC_IMG_LOAD_PART    1
  64
  65 #ifdef CONFIG_IMX_BOOTAUX
  66 /* Set to QSPI1 A flash at default */
  67 #define CONFIG_SYS_AUXCORE_BOOTDATA 0x60000000
  68 #define CONFIG_CMD_SETEXPR
  69
  70 #define UPDATE_M4_ENV \
  71         "m4image=m4_qspi.bin\0" \
  72         "loadm4image=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4image}\0" \
  73         "update_m4_from_sd=" \
  74                 "if sf probe 0:0; then " \
  75                         "if run loadm4image; then " \
  76                                 "setexpr fw_sz ${filesize} + 0xffff; " \
  77                                 "setexpr fw_sz ${fw_sz} / 0x10000; "    \
  78                                 "setexpr fw_sz ${fw_sz} * 0x10000; "    \
  79                                 "sf erase 0x0 ${fw_sz}; " \
  80                                 "sf write ${loadaddr} 0x0 ${filesize}; " \
  81                         "fi; " \
  82                 "fi\0" \
  83         "m4boot=sf probe 0:0; bootaux "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)"\0"
  84 #else
  85 #define UPDATE_M4_ENV ""
  86 #endif
  87
  88 #define CONFIG_MFG_ENV_SETTINGS \
  89         "mfgtool_args=setenv bootargs console=${console},${baudrate} " \
  90                 "rdinit=/linuxrc " \
  91                 "g_mass_storage.stall=0 g_mass_storage.removable=1 " \
  92                 "g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
  93                 "g_mass_storage.iSerialNumber=\"\" "\
  94                 "clk_ignore_unused "\
  95                 "\0" \
  96         "initrd_addr=0x83800000\0" \
  97         "initrd_high=0xffffffff\0" \
  98         "bootcmd_mfg=run mfgtool_args;bootz ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \
  99
 100 #define CONFIG_DFU_ENV_SETTINGS \
 101         "dfu_alt_info=image raw 0 0x800000;"\
 102                 "u-boot raw 0 0x4000;"\
 103                 "bootimg part 0 1;"\
 104                 "rootfs part 0 2\0" \
 105
 106 #define CONFIG_EXTRA_ENV_SETTINGS \
 107         UPDATE_M4_ENV \
 108         CONFIG_MFG_ENV_SETTINGS \
 109         CONFIG_DFU_ENV_SETTINGS \
 110         "script=boot.scr\0" \
 111         "image=zImage\0" \
 112         "console=ttymxc0\0" \
 113         "fdt_high=0xffffffff\0" \
 114         "initrd_high=0xffffffff\0" \
 115         "fdt_file=imx7d-sdb.dtb\0" \
 116         "fdt_addr=0x83000000\0" \
 117         "boot_fdt=try\0" \
 118         "ip_dyn=yes\0" \
 119         "videomode=video=ctfb:x:480,y:272,depth:24,pclk:108695,le:8,ri:4,up:2,lo:4,hs:41,vs:10,sync:0,vmode:0\0" \
 120         "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
 121         "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
 122         "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 123         "mmcautodetect=yes\0" \
 124         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 125                 "root=${mmcroot}\0" \
 126         "loadbootscript=" \
 127                 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 128         "bootscript=echo Running bootscript from mmc ...; " \
 129                 "source\0" \
 130         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 131         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 132         "mmcboot=echo Booting from mmc ...; " \
 133                 "run mmcargs; " \
 134                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 135                         "if run loadfdt; then " \
 136                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 137                         "else " \
 138                                 "if test ${boot_fdt} = try; then " \
 139                                         "bootz; " \
 140                                 "else " \
 141                                         "echo WARN: Cannot load the DT; " \
 142                                 "fi; " \
 143                         "fi; " \
 144                 "else " \
 145                         "bootz; " \
 146                 "fi;\0" \
 147         "netargs=setenv bootargs console=${console},${baudrate} " \
 148                 "root=/dev/nfs " \
 149         "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 150                 "netboot=echo Booting from net ...; " \
 151                 "run netargs; " \
 152                 "if test ${ip_dyn} = yes; then " \
 153                         "setenv get_cmd dhcp; " \
 154                 "else " \
 155                         "setenv get_cmd tftp; " \
 156                 "fi; " \
 157                 "${get_cmd} ${image}; " \
 158                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 159                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 160                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 161                         "else " \
 162                                 "if test ${boot_fdt} = try; then " \
 163                                         "bootz; " \
 164                                 "else " \
 165                                         "echo WARN: Cannot load the DT; " \
 166                                 "fi; " \
 167                         "fi; " \
 168                 "else " \
 169                         "bootz; " \
 170                 "fi;\0"
 171
 172 #define CONFIG_BOOTCOMMAND \
 173            "mmc dev ${mmcdev};" \
 174            "mmc dev ${mmcdev}; if mmc rescan; then " \
 175                    "if run loadbootscript; then " \
 176                            "run bootscript; " \
 177                    "else " \
 178                            "if run loadimage; then " \
 179                                    "run mmcboot; " \
 180                            "else run netboot; " \
 181                            "fi; " \
 182                    "fi; " \
 183            "else run netboot; fi"
 184
 185 #define CONFIG_CMD_MEMTEST
 186 #define CONFIG_SYS_MEMTEST_START        0x80000000
 187 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_MEMTEST_START + 0x20000000)
 188
 189 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 190 #define CONFIG_SYS_HZ                   1000
 191
 192 #define CONFIG_STACKSIZE                SZ_128K
 193
 194 /* Physical Memory Map */
 195 #define CONFIG_NR_DRAM_BANKS            1
 196 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 197
 198 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 199 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 200 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 201
 202 #define CONFIG_SYS_INIT_SP_OFFSET \
 203         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 204 #define CONFIG_SYS_INIT_SP_ADDR \
 205         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 206
 207 /* FLASH and environment organization */
 208 #define CONFIG_SYS_NO_FLASH
 209 #define CONFIG_ENV_SIZE                 SZ_8K
 210 #define CONFIG_ENV_IS_IN_MMC
 211
 212 /*
 213  * If want to use nand, define CONFIG_NAND_MXS and rework board
 214  * to support nand, since emmc has pin conflicts with nand
 215  */
 216 #ifdef CONFIG_NAND_MXS
 217 #define CONFIG_CMD_NAND
 218 #define CONFIG_CMD_NAND_TRIMFFS
 219
 220 /* NAND stuff */
 221 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 222 #define CONFIG_SYS_NAND_BASE            0x40000000
 223 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 224 #define CONFIG_SYS_NAND_ONFI_DETECTION
 225
 226 /* DMA stuff, needed for GPMI/MXS NAND support */
 227 #define CONFIG_APBH_DMA
 228 #define CONFIG_APBH_DMA_BURST
 229 #define CONFIG_APBH_DMA_BURST8
 230 #endif
 231
 232 #define CONFIG_ENV_OFFSET               (8 * SZ_64K)
 233 #ifdef CONFIG_NAND_MXS
 234 #define CONFIG_SYS_FSL_USDHC_NUM        1
 235 #else
 236 #define CONFIG_SYS_FSL_USDHC_NUM        2
 237 #endif
 238
 239 #define CONFIG_SYS_MMC_ENV_DEV          0   /* USDHC1 */
 240 #define CONFIG_SYS_MMC_ENV_PART         0       /* user area */
 241 #define CONFIG_MMCROOT                  "/dev/mmcblk0p2"  /* USDHC1 */
 242
 243 /* USB Configs */
 244 #define CONFIG_CMD_USB
 245 #define CONFIG_USB_EHCI
 246 #define CONFIG_USB_EHCI_MX7
 247 #define CONFIG_USB_STORAGE
 248 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 249 #define CONFIG_USB_HOST_ETHER
 250 #define CONFIG_USB_ETHER_ASIX
 251 #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
 252 #define CONFIG_MXC_USB_FLAGS   0
 253 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 254
 255 #define CONFIG_IMX_THERMAL
 256
 257 #define CONFIG_CI_UDC
 258 #define CONFIG_USBD_HS
 259 #define CONFIG_USB_GADGET_DUALSPEED
 260
 261 #define CONFIG_USB_GADGET
 262 #define CONFIG_CMD_USB_MASS_STORAGE
 263 #define CONFIG_USB_FUNCTION_MASS_STORAGE
 264 #define CONFIG_USB_GADGET_DOWNLOAD
 265 #define CONFIG_USB_GADGET_VBUS_DRAW     2
 266
 267 #define CONFIG_G_DNL_VENDOR_NUM         0x0525
 268 #define CONFIG_G_DNL_PRODUCT_NUM        0xa4a5
 269 #define CONFIG_G_DNL_MANUFACTURER       "FSL"
 270
 271 /* USB Device Firmware Update support */
 272 #define CONFIG_CMD_DFU
 273 #define CONFIG_USB_FUNCTION_DFU
 274 #define CONFIG_DFU_MMC
 275 #define CONFIG_DFU_RAM
 276
 277 #define CONFIG_VIDEO
 278 #ifdef CONFIG_VIDEO
 279 #define CONFIG_CFB_CONSOLE
 280 #define CONFIG_VIDEO_MXS
 281 #define CONFIG_VIDEO_LOGO
 282 #define CONFIG_VIDEO_SW_CURSOR
 283 #define CONFIG_VGA_AS_SINGLE_DEVICE
 284 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 285 #define CONFIG_SPLASH_SCREEN
 286 #define CONFIG_SPLASH_SCREEN_ALIGN
 287 #define CONFIG_CMD_BMP
 288 #define CONFIG_BMP_16BPP
 289 #define CONFIG_VIDEO_BMP_RLE8
 290 #define CONFIG_VIDEO_BMP_LOGO
 291 #endif
 292
 293 #ifdef CONFIG_FSL_QSPI
 294 #define CONFIG_CMD_SF
 295 #define CONFIG_SPI_FLASH
 296 #define CONFIG_SPI_FLASH_MACRONIX
 297 #define CONFIG_SPI_FLASH_BAR
 298 #define CONFIG_SF_DEFAULT_BUS           0
 299 #define CONFIG_SF_DEFAULT_CS            0
 300 #define CONFIG_SF_DEFAULT_SPEED         40000000
 301 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
 302 #define FSL_QSPI_FLASH_NUM              1
 303 #define FSL_QSPI_FLASH_SIZE             SZ_64M
 304 #define QSPI0_BASE_ADDR                 QSPI1_IPS_BASE_ADDR
 305 #define QSPI0_AMBA_BASE                 QSPI0_ARB_BASE_ADDR
 306 #endif
 307
 308 #endif  /* __CONFIG_H */